Search Documents

By Joan Weinberg

Real gross national produce (GNP) grew at a seasonally adjusted annual rate of 2.0% in the fourth quarter (table 1). The restrained quarterly growth rate was the slowest in 2 years, and was substantially slower than the 2.5 % rate of the previous quarter. According to the U.S. Department of Commerce, the summer drought reduced the fourth-quarter growth rate by 1.1 percentage points. A growing trade deficit and a reduction in business investment were the key economic factors curtailing growth. The trade deficit widened by $6.8 billion, reflecting both a surge of imports and a slowing of exports. Business investment declined 3.7%, mainly as a result of a slowdown in computer sales. On a year-to-year basis, the economy grew at an inflation-adjusted rate of 3.8% for 1988, the fastest in 4 years, despite the drought. However, on a fourth-quarter-to-fourth-quarter basis, real growth measured 2.7%. Increased exports and business spending for plant and equipment accounted for much of the 1988 GNP growth. Employment continued to grow as the manufacturing sector added 414,000 new workers (table 2). Of these, the primary metals industry added 26,000 workers, and the clay, glass, and stone industry added 10,000. The civilian unemployment rate remained low throughout 1988, fluctuating between 5.3% and 5.4% during the last quarter.

Jan 1, 1989

By Bernard J. Steblay

The U.S. Bureau of Mines has attempted to use ultrasonic signal travel-time measurements to measure loaded roof bolt strains. The strain measurements are then related to roof bolt loads through equations or empirical calibrations. Such techniques offer the potential of accurate, rapid bolt load measurement that does not disturb the anchotage. This report presents 6e research findings for a specific type of ultrasonic measurement instrument using a pulsed-phase-Iock-Ioop technique. This technique measures signal travel time indirectly by measuring frequency changes. A complete development of the applicable theory and detailed derivations of key equations is presented along with empirical laboratory and field results. The differences between anticipated and measured behaviors are analyzed and discussed. The report identifies problems encountered in applying pulsed-phase-Iock-Ioop technology to roof bolt load measurement and provides potential solutions to many of them. A key assumption of pulsed-phase-lock-loop theory is that driving and reflected signal frequencies will always be equal. Findings showed that not only were actual frequencies not equal but they were not stable or simply related. Reflection wave shape also was not stable. The ramification of these findings and ways to minimize their adverse effects are presented.

Jan 1, 1990

The Estonia Mine, operated by Eesti Energia Kaevandused AS (EEK), the mining division of the Estonian Government's energy company, Eesti Energia AS, is a large room and pillar mine located in Eastern Estonia. It supplied approximately 4.9 Mt/a of oil shale in financial year ending 2010, which is used for electricity and shale oil generation. Due to the Estonian climate and the power station's need for a dry product, Estonia Mine has developed a planning system where short-term demands of the power stations dictate the schedule. Such an arrangement requires maximising flexibility and consequently the mine only operated for 199 days in 2010.The footprint plays a key role in achieving mass mining rates as the 12 km + 12 km lease area allows the mine to split into mining districts that act independently of each other and maximise the number of work areas available. Coupled with this, the geology of the mine is relatively homogenous over the mining lease, simplifying the mine design and production methods.During the last five years, EEK has commissioned a comprehensive conveyor network. Consequently, material handling only requires loaders to dump oil shale direct from the production face onto a chain conveyor that feeds the conveyor network that ultimately supplies the enrichment plant. Dewatering is also of critical importance, with 90 Mm3 of water discharged annually. EEK uses large trenches up to 3.5 m deep and 1.2 m wide to channel groundwater. Track mounted mechanical saws are used to cut slots in the floor, to control overbreak in blasting these trenches.EEK has introduced Salzgitter Machinenbau GB 280S auger drills that drill three 280 mm diameter holes simultaneously. This has improved void hole drilling times and reduced the drilling required for each face, reducing the overall production cycle time. Blasting activities have also been decoupled from other mining activities negating the need for firing times through the use of small independent firings, required to control vibrations.

Dec 6, 2010

By Mohammad Noaparast, Babak Fotoohi

"Due to certain advantages in (semi-)Autogenous-Ball mill circuits in most of the high-throughput ore grinding units of mineral processing plants, much attention is paid to optimize the mill performance. Despite the maturity of the grinding mill mechanical design, there had been made less attention to the efficiency of the grinding media in the past. In this research, the possibility of establishing a relationship between liner/lifter wear rate and variations in the composition of the iron ore (from Chadormalu mine) is investigated.Measurements and determination of liner/lifter wear rates and patterns concluded in recognition of critical liner segments exposed to much abrasion during the ore grinding. After metallurgical analysis of liner materials and correlation of wear rate with the ore composition, the homogeneity in the metallurgical microstructure of the alloyed steel (such as the uniform distribution and amounts of the constituent phases) was determined as the most influential factor in the response of the liner/lifter to the variations in the ore composition. Magnetite with greater abrasion index than hematite, in finer particles, is responsible for additional abrasion of liners; hematite with greater work index exists in the mill with larger particle sizes, thus it could produce wear on liner parts with less tolerance to impact as is the situation for martensitic steels.INTRODUCTIONThe mineralization in Chadormalu plutonic iron ore deposit is consisted of mostly magnetite, hematite, martite, apatite, quartz and carbonates. The average composition of the ore is presented in Table 1. In the processing circuit, the gyratory crushed ore reduced to 30 cm would finally be the feed to three similar 32’ semi-autogenous mills in parallel processing lines. The pulp in the mill would have the characteristics mentioned in Table 2. The quality of the mill output has its direct effect on the downstream processes either physically or chemically (e.g. in cycloning or flotation respectively). In order to take advantage of optimum performance for these circuits, a close control of the ore grinding conditions is necessary; because any shortages in throughput, liner/lifter damage or changes in ore composition could bring the unexpected casualties. In this work, it has been attempted to find (possibly) a reasonable relationship between variations in ore characteristics together with liner quality and the amount of wear rate in different liner/lifter segments of a semi-autigenous mill. Liner/lifter segments are supplied by three different domestic steel making companies. The alloy structure of the liners/lifters is made up of pearlitic chromoly steel."

Jan 1, 2005

By A Prinsloo, R Tewu

Automatic control of semi-autogenous grinding (SAG) mills has often been considered complex. Recent experiences at Century Zinc (worldÆs second largest open pit zinc mine) refute this. Together with operating knowledge and appropriate control techniques high quality control is achievable. In this application model-based, constraint, and multiple output control were employed. The control was implemented using standard blocks in the plant DCS. The resulting overall control strategy fulfils the operating objectives and controls the mill with minimal operator involvement over 95 per cent of the time. Previous campaigns using expert systems and complex DCS based control have lacked durability. Their fall into disuse is briefly discussed.

Jan 1, 2009

By Jeffrey R. Hill

To extend the life of the Merchants Railroad Bridge crossing the Mississippi River in St. Louis, MO, the owner implemented a rehabilitation and reconstruction project. The Merchants Bridge provides a key link in the transcontinental railroad system. The bridge is of local importance to the Terminal Railroad Association ? providing a link between St Louis and a rail switching yard in Venice, IL. The intent of the bridge rehabilitation is to keep the Merchants Bridge in service, even though the bridge was originally constructed in the 1890?s. The project involved replacing the East and West approach deck truss spans with new deck girder spans. The rehabilitation program required construction of new concrete piers to support the new spans. In order to reduce the track down time to two, ten day single track shutdowns, the specifications required that all foundation and substructure work be completed while leaving the existing spans in place. The preliminary bridge design specified rock-socketed drilled shaft foundations. Drilled shafts proved to be challenging due to working from beneath the existing bridge, a high water table, utilities, a flood wall, and existing rail way lines. The micropile alternative was technically appropriate given the access limitations, shortened the foundation rehabilitation schedule by several weeks, and realized a significant cost savings to the Owner.

Jan 1, 2006

The prospect of utilisation of phosphate ores which contain high P2O5 values associated with Al and Fe has produced a great deal of interest over many years. Processing options have generally been based on the utilisation of by-products which were required to offset the processing costs.   This paper presents a range of processing options which have been investigated at laboratory or technical scale on phosphate ores which predominantly consist of crandallite, CaAl3(PO4)2(OH)5.3H2O and millisite, Ca(NaK)Al6(PO4)4(OH)9.3H2O. Christmas Island (Indian Ocean) and Mt Weld (Western Australia) phosphate ores are good examples of such feedstocks. It is expected that these processes may also be applicable to such phosphate ores from other locations.

Jan 1, 1990

It is possible to divide industrial minerals into four general categories: 1. fuels, 2. construction materials, 4. agricultural minerals, and 4. industrial minerals. It is proposed to ignore the fuels in the context of this paper and deal in general terms with the others. Mining companies have often considered getting into the industrial mineral business because they can see a resource development with good growth and consistent profits. However, many mining companies being conversant with the metallic side of the industry have spent sleepless nights determining which industrial minerals are most suited for their particular situation. Some have got into the business for the wrong reasons and wished they had never heard of it. Others have successfully adapted to the industrial minerals philosophy and now operate in both metallic and industrial mineral arenas. There is a large difference between firstly, the philosophy and secondly, the functions of being in the industrial minerals business as opposed to metallicÆs. The philosophies can be considered in parallel but it is necessary to clearly have an appreciation of the dominant influences that affect industrial minerals.

Jan 1, 1984

By Jean Balech

This paper presents some results of dynamic loading tests performed on concrete piles driven in soft clay formation. The load transfer mechanism, measured in the dynamic increasing energy test (DIET), under blows of growing energy, is described in terms of mobilized normal forces diagrams and unitary local friction and displacements. It was observed that the lateral skin friction grows up to a maximum, in the soft clay layer and, gradually diminishes to a residual value when the system presents the maximum mobilized resistance. It may be concluded that the rupture load is not equal to the maximum mobilized point resistance plus the maximum mobilized local friction as suggested by most of static bearing capacity formulae.

Jan 1, 2002

By John H. Wright

The United States Antarctic Program (USAP), through its principal support contractor Raytheon Polar Services Co. (RPSC), has recently completed a three-year project comprising nearly 936 m (3,071 ft) of undersnow utility tunnels at Amundsen-Scott Station, South Pole, Antarctica. The tunnel serves the new station facilities that are currently under construction. It houses the piping that conveys fresh water from current and future water well sites, as well as waste water to repositories in abandoned wells. The undersnow tunnels permit year-round access for system operations and maintenance. The network of tunnels is entirely unlined and unsupported. And, for the most part, it maintains a rectangular cross section of 1.8-m-wide x 3-m-high (6 x 10 ft).The tunnel runs from 6 to 14 m (18 to 45 ft) below the surface. Eight 1-m- (3.3-ft-) diam raises bored from the surface serve the network as emergency escapeways.

Jan 1, 2002

By Michael Zachariah, Art Miller, David Kittelson, Gib Ahlstrand

This report describes an investigation in which we used iron-doped diesel fuel to generate metal-bearing diesel particles and a subsequent analysis of the particles using transmission electron microscopy (TEM) and energy-dispersive spectroscopy (EDS). For this study, DPM was generated by a 1.5-L diesel engine and the fuel was doped with ferrocene to enhance the level of iron in the system. The exhaust particles were collected on TEM grids and analyzed using the Philips CM12 TEM/EDS instrument. Results show that when the iron-to-carbon (soot) ratio (Fe/C) in the engine is low, the exhaust particles have morphologies similar to those for the undoped case, but at a threshold Fe/C value of 0.013 (for this engine), homogeneously nucleated metallic nanoparticles are formed and begin agglomerating. The number and size of these nanoparticles increase with level of doping. Metal-bearing particles that span a wider size range are also formed. Agglomeration of metallic and carbon particles is observed in two distinct modes: attachment of iron primary particles (5–10 nm in diameter) to carbon agglomerates, and coagulation of iron agglomerates (20–200 nm in diameter) with carbon agglomerates. Results of this work imply that as new engine technologies reduce soot levels in the engine and/or levels of trace metals in the fuel are increased, the generation of metallic nanoparticles may ensue, creating a potential health concern. Keywords: Nanoparticles; Particulate emissions; Metallic particles; Metal emissions

By P. A. Witt

"Highland Valley Copper is a conventional truck-shovel mining and flotation concentrator operation located 75 km southwest of Kamloops, British Columbia (Fig. 1).The ore is situated within a porphyry copper deposit and is mined at a rate of 135,000 mt/day from two separate open pits. The nearby mill produces concentrates containing 375 million pounds of copper and 5 million pounds of molybdenum metal yearly. In the Valley pit, head grades are roughly 0.40% Cu at a 0.23% Cu equivalent cut-off. The Valley pit strip ratio currently sits at 0.55:1 with waste quantities made up of separate rock and unconsolidated overburden units. From the mill, concentrates are trucked to nearby Ashcroft and then hauled by rail to ocean port facilities in Vancouver. The mine employs 950 people and is planned to operate until 2009. The operation is a partnership between Teck Cominco (63.9%), BHP Billiton (33.6%), and others (2.5%). Management is shared by the two principal owners and directed by a management committee."

Jan 1, 2005

By William R. Vogel

The Bureau of Mines Information and Analysis organization collects worldwide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. This data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 3291, to place the collection of mineral statistics on an annual basis. The most recent authority for the Bureau of Mines Information and Analysis activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress), which strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral- material production or consumption.

Jan 1, 1989

By (NIOSH) Publication

In 2004, a total of 2,011 coal mining operations reported employment to the Mine Safety and Health Administration (MSHA). Coal mines comprised 13.9% of all mining operations.

Sep 1, 2007

In 1953, Dr. N. H. Fisher of the Bureau of Mineral Resources, acting on behalf of the Society of Economic Geologists, which is considering the sponsoring of a uniform system of nomenclature for ore reserves, enquired from the Australasian Institute of Mining and Metallurgy whether it had ever considered this subject and particularly whether it had ever set up any standard definitions or specifications with regard to ore reserves.As this had not been done, but was thought to be desirable, the Council of the Institute appointed a Committee consisting of H. H. Dunkin, Associate, Professor of Mining Engineering, University of Melbourne (Convenor), E. A. Rudd, Professor of Economic Geology, University of Adelaide, I. N. Campbell, Chief Geologist of Western Mining Corporation; and the writer to consider and report on this supject.In December 1953, the Committee submitted its first report to the council and this report (reproduced here as an Appendix) was widely circulated among member companies, and engineers, with an invitation to comment on the proposal. A large number of, replies was received and studied.After studying the replies the Committee issued a second report in part as follows:-From these replies we have learned that the suggestions made in the first teport of the Committee are unacceptable to most of those interested, on one or all, of the following grounds;-(a) number of categories,(b) definition of categories;(c) nomenclature.

Jan 1, 1955

Toward the goal of maximizing minerals and metals recovery from domestic resources, the Bureau of Mines, U.S. Department of the Interior, has conducted in situ corrosion studies at the Salton Sea Known Geothermal Resources Area (KGRA) in the Imperial Valley, Calif., to evaluate and characterize materials of construction for geothermal resources recovery plants. General-, pitting, and crevice-corrosion characteristics of 13 commercially available alloys were investigated for periods of 15 and 30 days in seven process environments expected to be found in typical geothermal resources plants. Stainless steel alloy 29.4, Inconel 625, and the Hastelloys G, S, and C-276 were the most resistant to general corrosion, did not pit, and exhibited little susceptibility to crevice corrosion. Stainless steel alloys 430, E-Brite 26-1, and 6X had low general corrosion rates, but pitted and were susceptible to crevice corrosion. Stainless steel alloy 316 L had a low corrosion rate, but corroded intergranularly, pitted, and was susceptible to crevice corrosion and to stress-corrosion cracking. Titanium-1.5 nickel and TiCode-12 had low corrosion rates, did not pit, and were not susceptible to crevice corrosion. Carbon and 4130 steels had high corrosion rates, pitted, and had high susceptibilities to crevice corrosion. The major scale-forming mineral on the corrosion samples in most of the process environments studied was galena mixed with lesser amounts of other minerals.

Jan 1, 1979

By E. D. Gardner

This paper on the square-set system of mining embodies the results of a special study of the subject made as a part of the Bureau of Mines general investigation of mining methods and costs. Data for the paper were gathered by the authors during visits to mines using square-set mining, from Information Circulars prepared by consulting engineers to the Bureau on mining methods at individual mines, and from articles in the technical press and the Transactions of the American Institute of Mining and Metallurgical Engineers. The square-set system of mining is very widely applied and is one of the oldest methods in use in the United States. It is mainly employed for extracting relatively high-grade ore in heavy ground. It is also useful in taking out pillars left in mining by other methods. It is used to some extent as an auxiliary method with many underground systems and as an alternate with cut-and-fill, shrinkage, and open-stope methods when heavy ground is encountered. In some cases as much as 50 per cent of the ore may be extracted by square-setting at mines listed as using some other method of mining. A large tonnage is mined yearly by square-setting, principally in the Western States.

Jan 1, 1933

By K. Najim, D. Hodouin

"The raw ores which are processed in mineral processing plants exhibit very strong variations of their physical and chemical properties. As a consequence, the performances of the comminution and separation processes vary greatly from time to time. Model-based control strategies improve the performance of the plant; however, they require some form of adaptation to cope with the variations of the are properties.This paper deals with the use of adaptive techniques for the control of mineral processes. It begins with a survey on adaptive control algorithms including parameters estimation aspects. Then several examples dealing with crushing, rod, ball, autogenous and semi-autogenous grinding, flotation , drying and calcination processes are reviewed.IntroductionThe operation of the various processes of mineral processing plants (crushing, grinding, flotation, dewatering, etc.) is generally controlled using empirically tuned regulators of constant structure, such as PID controllers. To improve the operation performance, mineral processors try to implement specifically designed controllers, i.e. controllers based on plant dynamic models. Most of the time, these techniques improve the control of the mineral processing installations. However, modelling is a complex procedure because of the problems of measurement and data management, specific to this industry, and because of the variations of the model parameters. In this context model-based control strategies do not always bring the expected improvements or are sometimes discarded and replaced by more conventional techniques .The sources of variation of the dynamic behaviour of mineral processing systems can be classified into three categories: (I) the inherent changes of the raw ore properties (composition, grindability, mineralogical texture, etc.); (2) the process tuning modifications (grinding media loads, number of hydrocyclones, slurry level in flotation cells, agitation speeds, etc.); (3) the feedrate variation of the ore, water, chemical reagents, etc. All these factors change the fundamental properties of the process dynamics such as the grinding or flotation rates and the residence time in the equipment. The simplified linear models which are used to describe the process dynamics are not able to track the complex behaviour of the mineral processing systems when the amplitude of the sources of variation are too large. The mismatch between the model and the plant behaviour is then frequently a cause of model-based controller failures."

Jan 1, 1992

By VERITAS

THE most concentrated industry of major character in the United States is that of the Ford Motor CO., which is to say Henry Ford. Its sole function is to supply the public with a cheap motor car which it does to the extent of two million or so per annum. In doing this, a relatively small profit per unit is multi- plied to an enormous aggregate per annum and has resulted in the creation of one of the greatest industrial fortunes of the world. The industrial and sociological consequences of .this are bound to be immense. On the physical side the production of two million automobiles means the consumption of two or three million tons of materials, chiefly metals, in the 'direct form of the finished product', and a huge additional tonnage of coal and other things that ,are consumed en route, and also the labor of many thousands of men. In the development of a business on this scale it was but natural that the Ford Motor ,Co. should seek to supply itself with the raw 'materials it needs, and they being so largely coal and metals the company is brought into close contact with the mining and metallurgical industries. It is a huge consumer of - steel. It is the fourth largest consumer of copper. It is a large consumer of lead, tin, aluminum and zinc. The mining and metallurgical industries have, therefore, good reason to learn to know Henry Ford, his personality, his thoughts and his policies.

Jan 1, 1924

By D. B. Swanepoel

Hulamin Rolled Products (Ltd) developed a high Mn and Si containing alloy, EN 4017 as a scrap consuming alloy from the waste generated in producing their range of clad products for brazing of inter alia automotive heat exchangers. The multifaceted composition of this alloy (Al -1.2 wt% Si -1.1 wt% Mn -0.2 wt% Mg-0.26 wt% Cu) suggested that it might display some degree of strengthening via precipitate formation of the Mg2 Si-types. The aging isotherms constructed showed that EN 4017 with 0.19% Mg reached a lower peak strength (YS~210 MPa and UTS~260 MPa)compared to the EN 4017 material with 0.43% Mg (YS~270 MPa and UTS~325 MPa). The higher Mg variant of EN 4017 was comparable with the age-hardenable reference alloy EN 6061. Selected area electron diffraction (SAED) studies proved that the microstructure of age hardened EN 4017 contained a combination of ß', ß" and U2 phase after being aged at 175ºC for 65 h. The general microstructure contained precipitate free zones as well as grain boundary Si films, although these did not lead to significant embrittlement. The role of Mn dispersoids in the fracture mechanism of 4017 is also discussed. The article will compare the behaviour of EN 4017 with that EN6061. Keywords: Age-hardening, dispersoids, magnesium silicide, precipitate free zones

Jan 1, 2009