Search Documents

By John F. Wiss

A series of controlled experiments was conducted at four surface coal mines to study the effects of certain blast parameters upon the ground and air vibration. Preliminary scale-model blasts were conducted at a quarry to provide basic data. It was found that the amplitudes of the ground and air vibration were controlled by the maximum explosive weight per delay. Either cube root or square root scaling could be used for the seismic amplitudes, and cube root scaling could be used for the overpressure amplitudes. Both amplitudes were not significantly affected by the total charge weight per blast, the attitude of the boreholes, or the charge length or diameter. The overpressure amplitudes were affected by the charge depth, the use of cover over surface detonating cord, and the use of adequate stemming. The length of the delay intervals and the spacing of holes were important in determining the potential for reinforcement of the amplitudes in certain directions from the blasts. In downwind directions from the blast, the attenuation of the overpressure with distance decreases. Surface terrain did not significantly affect the overpressure amplitudes within the range investigated. The type of overburden affects the generation of both amplitudes and the propagation of the seismic amplitudes. Spectral analysis of the ground and air vibration is reported. A bibliography of pertinent literature is included as an appendix. A scaled distance of 300 ft/lb1/3 should produce a peak particle velocity of less than 1 ips and an overpressure of less than 128 dB linear peak. For square root scaling, a scaled distance of 75 ft/lbl/2 should limit the ground vibration to less than 1 ips.

Jan 1, 1978

Power Point Presentation

Jan 1, 2007

Mining steeply dipping coal seams is a difficult task in the mining industry. Prior to 1996, fully mechanized longwall mining methods along the seam strike direction were tried in China and other countries. Due to its larger coal reserve in steep seams, China made more but still limited progresses on mining in such seams than the other major coal-mining countries. In the last two decades, accelerated research efforts have been made to improve the mining technology in steeply dipping coal seams. Based on these works, a dynamic model of ?R-S-F? system under asymmetrical constrains in mining steep seam is established and the theory of strata control and hazard prevention begin to be formed. The key technologies for mining steep coal seams include: global and regional strata control methods in longwall face, methods for the longwall face machines to sustain static and dynamic loads, and flexible protection technology. These theory and technologies have been successfully applied to mining of steep coal seams of varying thickness and hardness, with hard and soft roof and floor, and with high potential of spontaneous combustion in China. In the recent years, the technology has been introduced to Russia, India, Uzbekistan and other countries where steep coal seams are mined.

Jan 1, 2012

By AIME AIME

The Institute Headquarters at Spokane was established at the Spokane Hotel, and included a Bureau of Information for the benefit and comfort of members and guests of the party during the time of the meeting. The first session, held Tuesday afternoon, Sept. 28, 1909, in the beautiful Convention Hall ,of Masonic Temple, was called to order by Mr. E. J. Roberts, Chairman of the Spokane Local Committee, who introduced Mr. J. C. Ralston, City Engineer, representing the Mayor of Spokane and the Spokane Chamber of Commerce. Mr. Ralston extended to the members and guests of the Institute a cordial welcome to the city of Spokane, substantially as follows:

Dec 1, 1909

Jan 1, 1882

By A. C. Fieldner

"Decline of the Beehive Coke OvenTwenty years ago a favorite theme of the crusader for fuel conservation was the enormous waste of valuable by-products incurred in the manufacture of blast-furnace coke in beehive ovens. Indeed, there was good reason for arousing the national conscience to this needless' loss of an irreplaceable mineral resource. In 1910, 83 per cent of the coke production was made in beehive ovens, from which surplus gas, tar, light oil, and ammonia, aggregating in value (at 1910 prices) 40 million dollars annually, were discharged into the atmosphere.In 1929, proportions were reversed and 90 per cent of the production was made in by-product ovens. The average value of by-products obtained in the production of 1 ton of coke in 1929 was $3.60, as compared with $1.16 in 1910, although the value of a ton of coke had increased only from $3.47 to $4.80. As shown in Figure 1,1 the production of by-product coke progressed rather slowly until 1915. War needs suddenly expanded the demand for coke and the by-products benzol and toluol for the manufacture of explosives. Except during the depression of 1921, this accelerating rate of production was maintained up to 1929, largely at the expense of beehive plants. The 1929 production of 60 million tons of coke will probably remain a record-breaking figure for several years. The developments which are now in progress in long-distance transmission of rural gas and in the utilization of volatile petroleum products and refinery gases for augmenting, city gas supplies may retard an other- wise accelerating demand for coke and coke-oven gas for domestic and industrial heating, Trends in Value of By-ProductsThe increasing value of by-products in comparison to the value of coke is shown in Figure 2. In 1913, the average value of by-product coke was $3.38, the value of the by-products per ton of coke was $1.41, and the cost of coal per ton of coke was $3,27, In 1929 not shown in figure) the value of the coke had risen to $4.80 per ton, the value of the by-products to $3.60, and the cost of coal per ton of coke to $5.07. The by-product values in were 155 per cent higher than in 1913, although the coke value had increased only 25 per And the cost of the coal 55 per cent. Actually the increase or the total value of coke plus by-products in this period was very little more than the increase in the coat of the coal, being 55per cent for coal and 60 per cent for coke plus by-products."

Mar 1, 1931

By Donald F. Rapp, Thomas E. Brown

The application of commercial explosives in an underwater environment, sometimes referred to as submarine blasting, presents the blaster with a unique set of demanding conditions which require exacting detail in design and application. There are two basic methods for removing rock under water: 1) "the drill and blast method"; and 2) "the dobying method." Because it is a far less effective method of blasting, dobying will not be addressed in this 'paper but suggested criteria can be found in the 16th Edition of the **DuPont Blasters' Handbook" page 371. Some examples of submarine blasting utilizing the drill and blast method include channel expansions, harbor construction, bridge pier footer excavations, utility excavation and demolition work.

Jan 1, 1994

By William R. Yernberg

The Society of Economic Geologists (SEG) held its biennial conference May 14 through 16, 2006, in Keystone, CO. SEG is an international organization with about 3,500 individual members with interests in economic geology. The 2006 SEG conference theme was “Wealth creation in the minerals industry — integrating science, business and education.” The conference exceeded expectations with 705 participants, including 102 students, from 44 countries. The conference featured 30 oral presentations, 24 professional posters and more than 70 student posters. The conference also included a trade show with 50 vendors, numerous field trips, workshops and social activities.

Jan 1, 2006

By By Staff

"Acid mine drainage can be controlled by water treatment, retardation of the pyrite oxidation reaction system, or enhanced prediction that allows preventive action to be taken. The Bureau of Mines is conducting research in each of these areas; the results of this research are summarized in the eight papers that comprise this volume. Field work to evaluate overburden analysis, alkaline injection, and bactericidal control of acid formation is described, along with two new inexpensive methods to treat acid mine water. These papers were prepared for an acid mine drainage technology transfer meeting held in Pittsburgh, PA, on April 3 and 4, 1985. INTRODUCTIONAcid drainage from coal mines is one of the most persistent industrial pollution problems in the United States. Over 5,000 miles of streams and rivers are adversely affected, primarily by underground mines that have been abandoned for decades. Meanwhile, at active mining operations and at sites where mining occurred after 1977, discharge water must be treated to meet fairly stringent regulatory limits--at a cost to the industry of over $1 million per day.The Bureau of Mines has a special responsibility to facilitate integration of mining and mineral processing with environmental safeguards. This responsibility is twofold: the development of techniques to reduce or eliminate environmental degradation, and the improvement of existing pollution control processes to make them more efficient and more cost effective. Research in acid mine drainage exemplifies the Bureau's concern for these environmental aspects of mining.This collection of papers summarizes much of the Bureau's recent research on acid mine drainage and will give the reader a sense of where the research is headed, in addition to providing details regarding new technology and recently acquired knowledge. The research papers address four basic objectives:"

Jan 1, 1985

This appendix contains the list of equipment, their corresponding number and their specifications with the quotations from the vendors/ manufacturers who can supply this equipment. The listings are arranged by process plant areas.

Jan 1, 1979

By Ivette E. Torres

Of the 15 selected non fuel mineral commodities detailed in table 12, only 3 indicated increases in worldwide consumption in 1992. As in 1991, decline in consumption levels of the selected commodities can be attributed to reduced levels of use in the former U.S.S.R. and Eastern Europe. Of the remaining 12 commodities, 2 magnesium and cadmium, stayed relatively the same, while the other 10, including iron and steel, all recorded decreases. Global consumption of iron ore is estimated to have fallen about 3.5 % or about 30 million tons. This is a greater decline than what was estimated for production of iron ore, which is down only 2.7% or nearly 26.5 million tons, suggesting an addition to stocks. The consumption trend for iron and steel has been declining since 1989. This has mainly been due to the continued drops in use in the former U.S.S.R. and Eastern Europe. Even as the European economy begins to turn upward, there may only be a slight increase in consumption of iron, steel, and cement, considering the high cost of construction needed to modernize factories and buildings in Eastern Europe. Many feel that the economies of these countries are limited by the current status of their industries.

Jan 1, 1994

By R. Lusignea

A device has been developed for nondestructive testing the holding power of split tube friction rock supports. It operates by measuring the amount of decrease in internal volume when the support is forced into the drilled hole. The pullout force or slip load is a function of this decrease in volume. The device gives readouts of the average internal diameter and predicted pullout force or the support. Laboratory and field tests showed excellent repeatability and good correlation between predicted and actual pullout force. The device is hand-operated, lightweight (7.5 lb) and can be used on any friction support.

Jan 1, 1983

Copper waste dump leaching is growing in importance because of the.large tonnages (up to 250,000 ton/day) of low grade waste rock available from open cut mining of copper deposits and proof that controlled leaching of copper from such dumps can be profitable.Overburden or waste rock, ranging in size from large boulders to fines, is dumped as cheaply as possible on sloping sites. Copper is leached from the dumps by applying up to 12,000 gal/min of leach solution (a combination of spent solution from cementation and make-up water) to the top of the dumps by various techniques.Efliuent from the dumps is sent to a cementation plant for copper recovery.Factors which may be controlled, either directly or indirectly, to give a controlled copper content in the dump efliuent (usually 1-2 g/l.) are the cycle of operations (i.e. the alternate wetting and drying periods), thevolume of solution applied to the dump, pH, Fe2+ and Fe3+ content or redox potential, oxygen content, bacteria and their necessary nutrients, and temperature.Dissolution of oxide copper minerals appears to be mainly a function of acid concentration. Copper sulphide minerals need oxidation for dissolution to occur and this is accomplished by a combination of oxygen,ferric ion, and bacteria. Oxidation of pyrite, oxidation of Fe2+ to Fe3 +, and hydrolysis of Fe3+ are of some importance in leaching practice. The presence of gangue carbonate minerals is detrimental.Physical factors connected with penetration of solution into large rocks are important and the treatment of an individual dump usually extends over a period of many years. Recovery of copper from solution is usually achieved by cementation with iron (usually in the form of crumpled cans) but the use of sponge iron is becoming more important. Iron consumption varies from 1 to 4 lbiron per pound of copper. Preconcentration of the copper in the efliuent solution by solvent extraction followed by electrolysis may become a useful method.Application of dump leaching techniques to metals other than copper depends on finding an economic method of recovering the metal from solution...

Jan 1, 1967

By D. Toporov, R. Abraham

"Gasification is a process of thermal conversion of solid carbonaceous materials into a gaseous fuel called syngas. Coal gasification is an efficient technology for a range of systems for producing low-emission electricity and other high-value products such as chemicals, synthetic fuels, etc.The paper presents the High-Temperature Winkler (HTW) gasification process, which is designed to utilize low-rank feedstock such as coals with high ash content, lignite, biomass etc. The process is characterized by a bubbling fluidized bed, where coal devolatilization and partial oxidation and gasification of coal char and volatiles take place, and by a freeboard where partial combustion and gasification of coal char take place.The recent development of the high-pressure HTW process is reviewed. Gasification of low-rank, high-ash coals with respect to gasification temperatures, conversion rates, and syngas quality is also discussed. The main HTW design steps required for an industrial-scale design are presented. Special attention is given to the process modelling, including global thermodynamic calculation as well as detailed CFD-based simulation of a reacting fluidized bed. Three-dimensional numerical results of the HTW process are also provided and discussed."

Jan 1, 2015

By W. J. Mcgaughey

A crosshole seismic imaging (tomography) experiment has been carried out in an underground mine in order to delineate waste rock within a massive sulphide ore body. Data comprising 1526 travel time measurements were inverted to yield a compressional wave speed image consistent with, and adding to, knowledge of the extent of the waste inclusions. An effective method of resolving travel time discrepancies measured on reversed ray paths is presented.

Jan 1, 1989

By Bill Almdal

Today?s presentation ? Role of the Regional Issues Working Group ? What does RIWG do? ? How can RIWG?s work benefit Stakeholders? ? Review of forecasts vs. reality ? How have past investment compared to the reality? ? Risks to future growth ? The growth potential is very high and so are the risks ? Examples of outputs ? Housing needs ? Growth in population ? Tires for large trucks The Regional Issues Working Group ? Our vision ? To provide a proactive process which promotes the responsible, sustainable development of resources within the Regional Municipality of Wood Buffalo for the benefit of all stakeholders ? What we do ? Facilitate planning for growth ? Facilitate effective and efficient resolution of issues ? Involve all of the resource developers and affected stakeholders in planning ? Develop plans for sharing benefits with Aboriginal stakeholders ? Benefits for Stakeholders ? Our forecasts include up-to-date information from all developers ? including information on employment and housing needs ? Our forecasts are the basis of planning for many stakeholders ? and can assist in their development planning

May 1, 2002

By Russell E. Griffin

Dielectric constants and dissipation factors were measured by the Bureau of Mines for 13 simulated lunar rocks over the 20-to 100-megahertz frequency range by means of the susceptance-variation method. Measurements were made at room temperature and normal atmospheric pressure. Results are presented and some comparison is made with data reported by others. The rocks used include a broad range of physical characteristics and chemical compositions from the large areas of volcanism in Oregon and northern California, and two nonvolcanic types. These rocks make up a suite of rock standards used by a group of laboratories engaged in lunar research. The data presented will add to the basic scientific and engineering knowledge needed to utilize extra-terrestrial mineral resources for support of future space missions.

Jan 1, 1974

By Andrew Cho, Changsoo (Kevin) Moon, Richard Flanagan, Brian Larsen

"INTRODUCTION Project Background The U.S. Army Corps of Engineers (USACE)/Port Authority of New York & New Jersey (PANYNJ), as part of their New York and New Jersey Harbor Deepening Project, will dredge this shipping channel to a depth of 16.5 m below mean low water (MLW). By deepening the channel, the new generation of larger, “post-panamax” container ships coming to U.S. waters as a result of the expansion of Panama Canal can be accommodated in local marine terminals, helping to retain the nearly 300,000 jobs and $12 billion in annual wages the PANYNJ provides to the region. The existing siphons are situated at a depth that could be compromised by the planned dredging of the channel (nycedc.com). The purpose of this project is to build a new 1.83 m diameter water main inside a 3.66m diameter tunnel replacing the two existing siphons in order to provide the necessary backup water supply to Staten Island across the Anchorage Channel within the Upper New York Bay from Brooklyn. The proposed tunnel is approximately 2.9 km long and at a depth of at least 26 m below MLW. The project is funded jointly by New York City’s Department of Environmental Protection (NYCDEP) and PANYNJ and is managed by New York City Economic Development Corporation (NYCEDC). The contractor of the project is Tully/OHL JV, the designer is CDM/HMM JV, and the CM is LiRo/PB JV. History of New York City’s Soft Ground Tunneling The New York City area has a relatively long history of soft ground tunneling, commencing in the late 19th century. Construction of the first Hudson River tunnel crossings was begun (but not completed) in 1874 for the Hudson & Manhattan Railroad using compressed air supplying a shield. The work continued intermittently until the project finally opened for service in 1907. These 1.72km long tunnels (maximum depths of 29 m) are still in operation and now operated as the PATH Tunnels. They are approximately 5.5m diameter utilizing cast iron segments. The river bed consisted of primarily silt with shallow rock near the New York side. Air “leaks” occurred during the compressed air excavations resulting in some serious “blows” with water and soil entering the tunnel, including one incident with 20 deaths."

Jan 1, 2016

By Dominic Orf, Gregory Poole

On December 12, 2018 at 4:14 AM EST, an earthquake registering a 4.4 magnitude on the Richter Scale occurred in central Tennessee. According to a survey posted on the USGS website, this earthquake was felt throughout the southeast and even as far away as Arnold Nebraska. That’s over 900 miles (1,448 kilometers) from the epicenter. We recorded the vibrations from this earthquake on 44 different seismographs that were set up with remote access to continuously monitor vibrations from blasting activities. Having this data gave us an opportunity to compare the vibrations caused by earthquakes and blasting. A simple observation of the amplitudes, frequencies, and durations is enough to notice that vibrations from earthquakes are very different than vibrations caused by blasting in mining and construction. We were also able to observe the dissipation of the vibrations from the earthquake and see if the low frequencies, that are typical of earthquakes, dissipate at a consistent rate. Regression calculations were performed in order to see if there was a good data fit and if a specific vibration prediction could be made based on the magnitude of an earthquake. “How does quarry/mining/construction blasting compare to the Richter Scale?” This is a very common question that we get from homeowners when discussing vibrations due to blasting activities. This paper is intended to provide some simple answers for such a complicated question. Both the Richter and Mercalli scales are compared to the particle velocities as they were recorded from this earthquake.

By Green P. F

Apatite Fission Track Analysis (AFTA) is a thermal history reconstruction tool that enables determination of magnitude and timing of maximum paleotemperature and paleo-geothermal gradient at the time of maximum paleotemperatures. From this information, the amount of section missing at major unconfornities can be estimated and incorporated into basin models. The Gippsland Basin has a number of distinct problems that can be tackled using AFTA. 1. The nature of the regional break between the Late Cretaceous-Tertiary Latrobe Group and the underlying Early Cretaceous Strzelecki Group. 2. The tectonic history of the basement flanking the basin and its effect on sediment composition. 3. The age of igneous activity in the basin, as typified by the widespread basaltic plugs and dykes intruding the outcropping Strzelecki Group. Major uplift and erosion within, and adjacent to, the early Cretaceous rift basin in the Mid-Cretaceous, at -95 to 100 Ma, initially constrained the Latrobe Group depositional area to the central deep of the Gippsland Basin and provided an elevated source of quartz-rich detritus for the Latrobe Group reservoirs. This is in marked contrast to the preceding period in the early Cretaceous when contemporaneous volcanism dominated as a source of detritus, producing quartz-poor lithic sandstones, in which a host of attendant diagenetic reactions destroyed their reservoir potential. Initial uplift and erosion of the volcanogenic Strzelecki Group also occurred in the mid-Cretaceous as revealed by a number of distinct inversion structures, and erosion of this material will have locally provided very poor quality sand to the basal Latrobe Group.

Jan 1, 1992