Search Documents

By Dennis R. Dolinar

The National Institute for Occupational Safety and Health?s Pittsburgh Research Laboratory conducted a full-scale test of a composite polyurethane-aggregate seal in a hydrostatic chamber at the Lake Lynn Experimental Mine. This composite seal consisted of a polyurethane and limestone aggregate core that was formed between two concrete block walls. In the hydro-static chamber test, water is used to pressurize the seal. During the test, the maximum average water pressure the seal was able to withstand was 18.9 psi. Further, the seal began to yield at an average water pressure of only 17 psi. At the time of the test, the minimum seal design requirement was 20 psi under 30 CFR4 75.335 (2005). Therefore, based on this test, the seal did not meet the regulatory minimum design requirement. Uniaxial compressive tests conducted on samples from the polyurethane-aggregate core revealed that both the compressive strength and the elastic modulus of the material were much less than that for polyurethane only with a density of 10.0?12.0 lb/ft3. The significant reduction in the strength and stiffness of the polyurethane-aggregate mixture results from the formation of a soft polyurethane foam around each piece of aggregate. The formation of the soft foam seems to be caused by residual moisture from the aggregate. The moisture also caused the density of the polyurethane in the polyurethane-aggregate mixture to be less than the design requirements. The lower density of the polyurethane in the mixture, along with the formation of zones of pure polyurethane only, resulted in the overall seal density being less than the design requirements. During seal construction, steps were taken to control the moisture, but were not successful. An analysis of the seal failure showed that the calculated shear stresses at failure and the estimated shear strength of the polyurethane-aggregate mixture are fairly close. This suggests that the strength properties of the polyurethane-aggregate mixture along with a weak zone of poorly bonded aggregate controlled the maximum pressure the seal could withstand. At the time of the seal testing, the minimum design requirement was 20 psi, as specified at 30 CFR 75.335 (2005). New emergency temporary standards for seal designs were promulgated on May 22, 2007, with a minimum requirement of 50 psi under specified conditions. However, it will be shown that the evaluation of the polyurethane seal performance as designed to meet the older 20-psi criterion can be relevant to the design requirements under the new standards.

Jan 1, 2008

By AIME AIME

THE following paragraphs, constituting the concluding portion of the Annual Report of the Council for 1903, have been withheld from publication until now, in order to make them as accurate and complete as possible. They will be published in Volume XXXV. of the Transactions in their proper place at the end of the said Annual Report. Franklin Ballou was born in Pittsburg, Pa., May 29, 1845. He was the son of an old resident, Arthur Ballou, a manufacturer and wholesale dealer in vinegar. In early youth Franklin attended the Western University of Pittsburg, but left school at the age of 16 to become book-keeper for his father, upon whose retirement from business, in 1868, he associated himself with Walter C. Childs, of Pittsburg, in the manufac¬ture of furnace-grates and asbestos-cement for blast-furnaces. This firm was known as W. C. Childs & Co., and did a success¬ful business for several years. In 1869 Mr. Ballou married Miss May S. Wilson, daughter of Judge Wilson, of Lewistown, Pa. In 1876 he spent several months traveling in the West and studying the mining industry, which greatly interested him. In consequence of this journey, he wound up his business in Pittsburg and removed in 1877 to Georgetown, Colo., where for several years he conducted a sampling-works, and built up an extensive business as an agent for the sale of ores, besides engaging to some extent in mining enterprises. , It is said that he controlled at one time about one-eighth of the output of the Leadville mines. In the early 80's, he became Vice-President and General Manager of the Bimetallic Smelter at Leadville, of which Mr. David H. Moflat was the principal owner. This was practically the first successful demonstration of pyritic smelting in Colorado. Upon the sale of the works in 1897 to the American Smelting and Refining Co., Mr. Ballou retired

Jan 1, 1905

By V. B. Dale

This paper is one of a series covering the mineral resources of the Nation. It briefly describes most of the known tungsten deposits of New Mexico. Most of the descriptions are from field examinations by the senior author. Reported tungsten occurrences that were not visited are listed below: Colfax County: Occurrences of ferberite in thin veins in Willow Creek near Elizabethtown.4/ Dona Ana County: Small, low-grade occurrences of scheelite near the summit of the Organ Mountains about 15 miles east of Las Cruces. Hidalgo County: Scheelite reported in the Daisy mine 7 miles southeast of Hachita. Ores are carbonates containing copper, gold, silver, and bismuth.5/

Jan 1, 1959

By K. C. Lahiri, H. P. Das, G. G. Sarkar

"The petrographic components of any particular rank of coal often show some distinct physical and chemical characteristics. Therefore, their pro-portionate distribution in a coal greatly influences the technological behaviour of the coal.In any size or gravity separation of a coal, the petrographic constituents become segregated to different degrees in some preferred size or specific gravity range. Therefore, a knowledge of the petrographic nature of the washed and/or screened fractions is often considered essential in selecting the most efficient method for coal preparation and in exploring the proper evenues for its utilization.A graphical method is described in this paper to indicate the mineral-matter content and the petrographic components of the washed fractions of a coal at different ash levels of separation in the form of a new washability diagram. This diagram can be conveniently used to assess or predict the petrographic composition of clean coal or sinks corresponding to any desired ash level in the cleans. With the help of this diagram, it is also possible to locate the yield level of cleans at which maximum enrichment of vitrinites and exinites occurs with the least amount of mineral-matter content."

Jan 1, 1971

By L. F. Miao

Studies were carried out to investigate the ultimate soil pressure acting on pile(s) undergoing lateral soil movement in soft clay. A special apparatus has been designed to apply a uniform rectangular profile of lateral soil movement on the rigid pile(s) with pinned head and tip conditions to obtain the ultimate soil pressure. The piles were 16 mm (5/8 in) in diameter. For the pile group tests, the behavior of different number of piles (2, 3, 4, 6 and 9), pile arrangements and center-to-center spacings (3 and 6 diameters) were investigated. In this paper, the group factors of 11 combinations of number of piles, pile arrangements and pile spacings are presented. The group factors are given for individual piles in a pile group as well as for the entire group. Generally, the group factors of individual piles in a group varied significantly according to pile spacing in both directions, and pile arrangement; the group factor of the whole group reduced with an increasing number of piles, and increased with increasing pile spacing. For a pile group with the same number of piles but different pile arrangement, no significant difference was found in the group factors for the entire group.

Jan 1, 2008

By Knevitt L. T

PART 1Details of Kiewa Scheme.Introduction.Topography.Preliminary Investigations.Geology.Description of Project.Details of Main Works.Main Transmission of Power.Construction Facilities.PART 2Underground Works.Summary of Projected Works.Administration.Labour.Surveying.Safety and Accident Prevention.Medical Attention and First Aid.PART 3No. 4 Head Race Tunnel.Summary.Geology.

Jan 1, 1950

There is a saying, ?If it moves, it vibrates.? This is especially true in our modern industrial environments, where workers use powered tools, machinery, vehicles, and heavy equipment. How workers are affected by these elements of the industrial working environment is a concern of health professionals, govern­ments, and scientists around the world. How to adequately assess the effects of human vibration exposure is an equally important issue. The human body comprises a dynamic structure that is living, intelligent, and complex. Consequently, it is not unreasonable to consider that exposing the body to an array of vibration environments would result in outcomes that are not necessarily simple or easily predictable. Sensations caused by vibration may include nausea, annoyance, discomfort or pain, and exhilaration or pleasure. Many factors contribute to the effects of vibration on humans, including the characteristics of the motion and the exposed indi­vidual, the activities of the exposed individual, and various elements of the environment. There have been attempts to summarize the effects of occupational vibration exposures by simply recommending the avoidance of certain frequencies of vibration or by providing a graphical method, i.e., a single curve displaying all human responses to all frequencies. However, such efforts have not withstood the scrutiny of scientific research and analysis. Thus, attendees and participants at this professional gathering now have the rare opportunity to benefit from the technological advances and new scientific research to enhance their understanding of human responses to vibration that suggest more than a simplistic approach. In the tradition of the First American Conference on Human Vibration (1st ACHV) held in Morgantown, WV, June 2006, the 2nd ACHV provides a forum for scientists, engineers, medical doctors, industrial hygienists, and educators to learn and advance research and education in the specialized area of human body vibration. The conference was organized by the Mechanical and Industrial Engineering Department, University of Illinois at Chicago, with support from the National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory. As with the first conference, the 2nd ACHV provides the unique opportunity to learn about the current activities of peers and colleagues and to exchange information on topics of interest such as human response, human modeling, experimental design, sensors, new technologies, and epidemiological studies of human responses to hand-transmitted and whole-body vibration. The conference organizers hope that the publication of these conference proceedings continues to foster new research and technological advances to reduce health hazards associated with occupational vibration exposures.

Jun 1, 2009

Jan 1, 2003

By FRANCIS FEEHAN

Safety first is no longer merely a motto ; in some industries and in some parts of the mining industry it is an accomplished fact . In connection with the National Safety Competition of 1928 in which 284 mines and quarries participated , 42 plants were operated without a single lost - time accident . The winning company in the bituminous group had an accident severity rate of 0.053 per thousand man hours of exposure . Excellent safety records of various kinds are becoming more and more frequent , and the indication is that in reality safety is first in many mines and qquuaarrrriieess .. The safety achievements in the Stewart mine of W. J. Rainey , Inc. , are unusual even among mines winning awards in the competition .

Apr 1, 1930

By Jack Green

Within three major tectonic time frames of earth history: Microplate (±3.8 - ±2.6 billion years), intraplate (±2.6 - ±1.3 b.y.), and macroplate (=1.3 b.y. - present), precious - metal deposits are confined to specific structural, depositional and physico-chemical environments. Precambrian primary gold deposits are localized in two microplate greenstone episodes (±3.7 and ±2.7 b.y.); secondary gold in Witwatersrand placers (±2.6 b.y.). Precambrian primary platinum group metals are in anorthositic facies of layered mafic intrusions (±2.8, ±1.8 and ±1.0 b.y.). Most radioisotope mineral dates cluster - at these times and are coincident with inflections on polar wandering curves. These coincidences may reflect episodicity in lunar tidal disruptions and global deceleration effects in crust and outer core during micro- and intra- plate phases. Macroplate tectonics and an oxygenated atmosphere created favorable conditions for strata-hosted and plate suture gold and silver deposits. "Black smokers" at constructive plate margins and calc-alkalic calderas at destructive plate margins are loci for hydrothermal gold and silver.

Jan 1, 1984

By Jones S. C

The problem of sealing a fluid serieite zone at a hole depth of 4000 ft was overcome by using a composite non-return valve plug and rod assembly which enabled cement to be forced under pressure into the zoneà

Jan 1, 1966

By D. Pennington

Ground-water levels and subsidence have been monitored over a longwall panel of a deep coal mining operation located in western Pennsylvania. The monitoring network includes eleven ground-water monitoring wells completed to measure water level changes in separate shallow and deep aquifer zone-, and 50-foot surveyed subsidence stations parallel and perpendicular to the panel centerline. Monthly monitoring data were collected during the premining, mining, and postmining tine periods. Aquifer testing and borehole geophysical logging were conducted during premining, and post-mining conditions to document any changes in aquifer properties and ground-water flow patterns. Results indicate ground-water declines were located with respect to the mining face and mined longwall panel. Dewatering of the deep aquifer zone caused a significant water level decline in deep wells; however, the shallow aquifer zone was isolated fro major impacts by an aquitardal layer during, the, one-year period. Transmissivity data were greatly impacted by fracturing, in the highly anisotropic aquifer system. Borehole geophysical logging indicated changes in ground-water flow patterns and zones of increased fracturing from subsidence.

Jan 1, 1984

By M. N. Rubin

This report summarizes the work performed under USBM contract J0100018. The purpose of this work was to document the currently available noise control techniques that can be incorporated into new coal preparation plants during the design stage. This was accomplished by reviewing the related experience of the contractor and subcontractor (Bolt Beranek and Newman Inc.), conducting an extensive literature search, visiting operating coal preparation plants, and contacting various equipment manufacturers. The treatments addressed include equipment substitution, changes in plant layout, and retrofit treatments for existing equipment.

Jan 1, 1982

By T. Tholana, P. N. Neingo

"Mining companies globally are currently facing severe economic and financial challenges. In addition to global challenges, the South African mining industry has to face other operational challenges that are unique to the country and which threaten the survival and competitiveness of the industry. Profit margins are being squeezed by rising costs and decreasing commodity prices, while labour productivity is greatly affected by intermittent labour unrest. This paper analyses how the South African gold mining industry has performed pre-, during, and post the global financial crisis of 2008. The competitiveness of the industry in terms of labour productivity and industry cost curve position is analysed for the period 2006–2013 to assess the impacts of both the global financial crisis and labour unrest. An analysis of the South African gold mining industry is presented at company as well as mine level. Productivity measure in this paper is limited to labour productivity, in line with limited reporting on productivity. All the data analysed was obtained from the public domain. IntroductionSouth Africa dominated the world as the number one gold producer until 2009 when China took that position, and today South Africa ranks fifth after China, Australia, Russia, and the USA. According to Statistics South Africa (2009), South Africa still had about 30 years of production in the gold sector, a forecast that fluctuates based on the day’s modifying factors. Although South Africa has a comparative advantage in terms of minerals endowment, there are challenges faced by the mining industry that hinder translation of the comparative advantage into a competitive advantage. The industry continually seeks to address these challenges to remain competitive in global markets while addressing national and community needs.Neingo and Cawood (2014) argued that stakeholders in mining are continually concerned with mine management’s ability to translate use inputs effectively into quality outputs. They further suggested close monitoring of effective utilization of people, materials, and money to obtain maximum production of commodities under given conditions. Productivity is measured in various ways, including unit cost, output per employee, and output per unit capital equipment"

Jan 1, 2016

By C Hall, J L. Mauk

New 40Ar/39Ar dates of vein and wall rock adularia from seven epithermal deposits and one porphyry copper prospect help constrain the ages of mineralisation in the Hauraki Goldfield. Vein adularia from the Paritu region yielded a single 40Ar/39Ar plateau date of 16.315 ¦ 0.066 Ma. Five 40Ar/39Ar plateau dates of three samples of vein adularia from the Opitonui deposit overlap within error to yield a preferred age of 13.149 ¦ 0.016 Ma. Two samples of vein adularia from the Night Reef at the Broken Hills deposit yield exceptionally flat 40Ar/39Ar plateaus, and all dates overlap within error to provide an age of 7.121 ¦ 0.010 Ma. Two 40Ar/39Ar plateau dates of one sample of vein adularia from the Wharekirauponga deposit overlap within error to provide an age of 6.318 ¦ 0.061 Ma. Four 40Ar/39Ar plateau dates of three samples of vein adularia from the Maratoto deposit overlap within error to provide an age of 6.411 ¦ 0.022 Ma. Two samples of adularia from altered wall rock at the Sovereign deposit yield three 40Ar/39Ar plateau dates that range from 6.547 ¦ 0.021 to 6.806 ¦ 0.028 Ma. This suggests that mineralisation formed around 6.6 Ma, but the results are complicated because the adularia contains minor illite that post-dates adularia formation. Results from the Karangahake deposit are complex. Two samples of vein adularia yield three 40Ar/39Ar plateau dates that range from 6.116 ¦ 0.116 to 6.901 ¦ 0.101 Ma, whereas one sample of wall rock adularia that contains minor late illite yields two 40Ar/39Ar plateau dates that overlap within error to provide a date of 5.734 ¦ 0.041. The range of dates indicates that more work is necessary to understand the history of mineralisation at this deposit. Two samples of vein adularia from the Tui deposit yield four 40Ar/39Ar plateau dates that overlap within error to provide an age of 5.714 ¦ 0.017 Ma. These results confirm previous work that indicates that the ages of epithermal deposits young southward in the Hauraki Goldfield. These results are also consistent with previously postulated different ages for deposits hosted in Kuaotunu Subgroup rocks in the northern goldfield (>10 Ma), and deposits hosted in Waiwawa Subgroup rocks in the southern goldfield (7.1 to 5.7 Ma).

Jan 1, 2005

By CHRISTOPHER D. HEBERT, SCOTT W. HOFFMAN

All Rights Reserved. Printed in the United States of America. Information contained in this work has been obtained by SME, Inc. from sources believed to be reliable. However, neither SME nor its authors guarantee the accuracy or completeness of any information published herein, and neither SME nor its authors shall be responsible for any errors, omissions, or damages arising out of use of this information. This work is published with the understanding that SME and its authors are supplying information but are not attempting to render engineering or other professional services. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of the publisher. Any statement or views presented here are those of individual authors and are not necessarily those of the SME. The mention of trade names for commercial products does not imply the approval or endorsement of SME.

Dec 1, 2019

By N Coplin

Australian Coal Association Research Program (ACARP) project C25073 was proposed by industry stakeholders seeking a potential solution that improves underground air quality and reduces operational costs associated with technology used to control diesel particulate emissions in the underground coal mining environment.The need to protect workers from diesel particulate matter (DPM) has lead the underground coal mining industry to install disposable filter systems on their vehicles. While the disposable filters are efficient at removing significant amounts of DPM, the following major issues have arisen:- high cost of operations; disposable filters cost $A250–300 each and need to be changed at least once per shift resulting in an estimated cost of up to $A164 M/a, in filters alone, to the NSW underground coal mining industry- improper installation, damaged seals and lack of installing a new filter when the old filter is removed; workers are still being exposed to excessive amounts of DPM.The ACARP project successfully demonstrated significant DPM emissions reduction comparable to the incumbent disposable technology on a proof-of-concept wall-flow diesel particulate filter (DPF) system, as well as satisfactory system robustness when assessed using an industry representative test cycle representing operations of a load haul dump (LHD) vehicle typical of that used by the Australian underground coal industry. It was noted in testing that the technology increased modal NO2 formation, but was compliant over typical operational duty cycles.One of the key benefits with the use of a wall-flow DPF system is its tamper-proof design, mitigating the risk of operating unfiltered diesel plant in poorly ventilated areas. Elimination of the need for continual replacement of disposable filters provides significant operational savings estimated to be up to 80 per cent of the incumbent technology.In addition to the above, the project also delivered a number of significant contributions to the knowledgebase of the Australian and international coal industry with regard to the characterisation of operations and control of emissions.CITATION:Coplin, N, 2017. Wall-flow type diesel particulate filter system to replace existing wet element filter systems used in typical LHDs in underground coal operations, in Proceedings Australian Mine Vent Conference 2017, pp 119–128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By Shosei Serata

The Stress Control Method improves productivity and safety in underground coal mining. The method stabilizes the roofs and floors of mine openings in both shallow and deep coal beds, regardless of whether or not there are ground stability problems. This paper describes the means by which a tapered pillar experiment is used to collect in situ data, which is then used as input for a computer model. The resulting computer model is then used to optimize Stress Control design for the mine under study. The behavior of any underground coal mine is not elastic, as is generally conceived in the conventional view of rock mechanics, but rather is highly time-dependent and site-specific. Unfortunately, conventional rock mechanics methods based on the elastic principle are not able to capture the highly non-elastic nature of ground behavior which actually occurs. To capture actual behavior, a new method of study is required. In this regard, geomechanical study of an underground coal mine may be compared to studying the behavior of a living fish. Its true behavior zannot be understood by examining it "dead in the laboratory. It Is the "live" nature of the coal mine that is required for design optimization of the Stress Control Method in the given mine. The Stress Control Method is based on a time-dependent theory of the global behavior of the mine ground, which generally contradicts the conventional elastic theory of ground behavior. Therefore, site-specific adaptation of the Stress Control Method required a comprehensive understanding of the global behavior of the mine as a function of time and site-specific ground conditions.

Jan 1, 1986

By Alexander Filotti, Stanley Merjan

"Abstract. The paper shows the benefits and accomplishments of this relatively new but established product on the pile foundations market in the United States. The first part of the paper describes general aspects of the design, construction, and geotechnical capacity (designed and in situ) of Tapertube piles. The qualities resulting from the design and manufacturing of the Tapertube pile will be presented first.The second part of the paper describes the installation of Tapertube piles for an addition to Terminal One at JFK International Airport and The Edge development. A carbon print analysis for both projects is developed using the EFFC-DFI carbon print calculator. For the JFK project the benefits of using BIM in redesigning the project for Tapertube piles are explored.General description.The tapertube pile consists of a tapered tubular bottom section attached to a conventional pipe extension. The 50 ksi steel for the taper is mechanically folded into a polygonal cross-section (usually 12-sided) with a longitudinal welded seam. The tapers are fabricated in many sizes with bottom diameters varying from 8 to 14 inches, top diameters from 12 to 20 inches, lengths from 10 to 35 feet, and steel thicknesses from 3/16 to 1/2 inch. A conical steel shoe or a flat plate is welded to the bottom of the taper and the top of the taper is circularized to match the outside diameter of the pipe extension. The inclination of the tapers is generally between 1.5% and 2.5%.The pipe extension is fully butt welded to the taper and has the necessary length for the pile to develop the requisite capacity. Concrete fill for the piles is generally 4,000 p.s.i. or more. Typically the piles are shopassembled and shipped to jobsites in lengths to 80 feet."

Jan 1, 2014

By Elaine T. Cullen

Human beings are natural storytellers and story listeners. We learn very early that stories entertain us, but also give us the ?rules? about what is expected of us and how to make meaning of our experiences. Stories are integral to our lives, and have great power to change or influence how we think or how we react. They are an innate part of how we learn, and have obvious benefits to trainers or educators who are trying to impact what and how we learn. This paper and presentation discuss the social and cultural power of stories, and how they have been used to develop training for skilled blue-collar workers. Included will be examples as well as suggestions for trainers on where to find stories, what type of stories to pay attention to, and how to use them to improve occupational safety training.

Jan 1, 2008