Search Documents

By Cheng Pan, Qiugang Yuan, Xuewei Lv, Mei Liu, Enguang Guo

Land-based nickel resources include nickel sulfide and nickel laterite. With the consumption of high grade nickel sulfide, use of nickel laterite has received more and more attention. The mineralogy and sintering behavior of limonitic nickel laterite with high iron and low nickel and silica was studied to offer technical support for producing ferronickel through sintering–blast furnace route. The mineralogy results showed that the main phases in this kind of nickel laterite are goethite (FeO(OH)), gibbsite (Al(OH)3) and NiFe2O4. The TGA (Thermogravimetric Analysis) and DSC (Differential Scanning Calorimetry) revealed hydroxide minerals in addition to absorbed water. After the sintering experiments the chemical composition, phases present (XRD analysis) and physical properties of the sinter were studied. The content of FeO in the sinter increased with increasing basicity up to 1.3, and then decreased with further increase in basicity. The yield of sinter increased (from 73% to 80%) with increase in the basicity from 1.1 to 1.7, and then the yield decreased with the further increase in basicity. Mg(Ni)(Fe,Al)2O4 is the main phase in the sinter while MgCaSiO4 and Fe2SiO4 is the main binder phase when the basicity is 1.1~1.5, and MgCaSiO4, Fe2SiO4 and SFCA is the main binder phase when the basicity is 1.7~2.1.

Jan 1, 2014

By Isıl Kerti, Sibel Daglılar, Sinem Yıldırım

In this study, effect of rolling and coiling temperature in thermo mechanical controlled process (TMCP), on the microstructure and mechanical properties of dual phase (DP) steel according to martensite volume fraction (MVF) rate was investigated. By using various finishing mill exit temperature and cooling conditions that is controlled laminar cooling system, the microstructural evolution of coil improves the mechanical properties with lower costs and higher productivities, in comparison to the heat treatment after rolling. The main part of the paper contains the result of tensile, yield and microstructure properties of DP600 steel produced on hot strip rolling plant and run- out table line. The results show that a higher MVF and an increasing cooling rate after the last deformation raised strength of the DP600 steel. The yield strength and ultimate tensile strength increase by decreasing coiling temperature.

Jan 1, 2015

By Pengcheng Li, Wei-Tong Du, Yu Wang, Gang Wen

Carbon dioxide could be utilized as a weak oxidant and a kind of coolant to oxidize elements, meanwhile, helping control the temperature during the converter vanadium extraction process. However, the optimum content of CO2 and the cooling effect of CO2 at low content have not been reported. In this study, experimental research based on the influence of different CO2 contents from 0% to 25% injected to the vanadium-containing hot metal was carried out, as well as contrast experiments of O2-N2 mixed blowing. The results indicated that the optimum content of CO2 was 15%. Under the optimum condition, the oxidation of [C] was the lowest and the oxidation rate of [V] was 96.9%, while the temperature was also lower than the O2-N2 mixed blowing. This paper provide a potential property for utilizing CO2 during the converter vanadium extraction process.

Jan 1, 2016

By J. R. Donald

Surface and interfacial phenomena play a significant role in refractory performance. For example, the wettability of the refractory material with slag, matte, and metal influences infiltration and interfacial reactions. Yet, very little fundamental information regarding the surface properties of refractory materials and slag is available. Thus, in the present work, the sessile drop technique incorporating a high temperature furnace equipped with X-ray fluorescope was employed to investigate the surface and interfacial phenomena of fayalite-type slags on solid alumina at 1200?C. The iron to silica (Fe/SiO,) ratios employed were 1.4 and 2.0, and the oxygen potentials used were log p02 =-11 and log p02=-9 atmospheres. The contact angle between the fayalite-type slags and the alumina were determined to be relatively low, at about 16.9 to 19.6 degrees under the experimental conditions. The surface tension of fayalite slag (Fe/SiO2=1.4) at an oxygen potential of log -11 was 0.298, which agreed with the work of previous researchers. The surface tension of the fayalite was observed to increase with time. The spinel FeAl2O4. was determined to be the product of the interfacial reaction, and 8.8 to 15.8 mass percent alumina was dissolved into the slag after 40 minutes.

Jan 1, 1996

By Sylwia Zymankowska-Kumon, Rafal Danko, Józef Danko, Mariusz Holtzer

"Burning of ceramic materials is carried out at temperatures 900+ 1300°C, in dependence of the required functional properties. The Faculty of Foundry Engineering together with the Faculty of Material Engineering and Ceramics developed the technology of production of burned ceramic materials with using spent moulding and core sands. The mentioned above waste materials of the foundry industry fulfilled -in plastic masses intended for obtaining ceramic materials -the role of the addition weakening clay raw materials. The laboratory investigations were fully verified by the results of industrial tests. It should be pointed out that none negative effects were observed at the stage of mixing raw materials and preparation of plastic masses. The measurements of exhaust gases emissions performed during burning the products containing spent moulding sands as well as during the normal production did not exhibit any significant differences, which could have indicated the harmful impact on the natural environment.IntroductionSands are used by the foundry industry to make metal casting molds and are a mixture of silica sand, bentonite clay and carbonaceous additives or resins. During the casting process, the molten metal cause thermal decomposition of carbonaceous additives or resins, which results in the formation of potentially hazardous organics, that are emitted to the atmosphere and condense in the molding sand. Each year the U.S. foundry industry landfills about 10 million tones of sand because it is no longer suitable to make metal casting molds. A large high-silica sand content in spent foundry sands (SFSs) generates rational premises for their reuse in other than foundry practice fields. Efforts to divert the SFSs from landfills and encourage their beneficial use in manufactured soils, geotechnical applications, the construction industry (road construction, highway construction), the building materials industry (cement, bricks, limestone manufacture), in the filling of mining cavities or in landfill construction (roads on landfills, permanent covers) are make [1-7]."

Jan 1, 2013

By Adrien Antenen, Didier Villette

CITRON has developed a new process for the recycling of hydroxide sludge, household batteries, catalysts, automobile shredding residues, grinding sludge and other metal containing organic and inorganic waste. A pilot plant with a capacity of 1,000 tons per year has started operations in April 1998. In August 1999, an industrial plant became operational with an initial treatment capacity of 23,000 tons.

Jan 1, 2000

By Yuanbo Zhang, Qian Li, Helei Zhang, Heng Yu, Guanghui Li, Tao Jiang

"Large reserves of specularite iron ores have been found all over the world, which is characterized by high total iron grade, low gangues content, as well as low commercial price. However, it has not been widely used in sinter or pellet production due to its inferior sintering and roasting behaviors. It has shown that the proportion of specularite ores was increased as high as 40%~50% and good results was achieveed by using Composite Agglomeration Process (CAP), an innovative agglomeration process invented by Central South University. But the mineralization of specularite is still unknown during composite agglomeration processing. In this paper, the induration characteristic of specularite ore is studied by simulating CAP in laboratory, as well as microstructure analysis of CAP product. The results show that specularite pellet is mainly indurated through recrystallization of Fe2O3, calcium ferrite within high basicity sinters matrix interweaves with the recrystallized Fe2O3 on the surface of the pellet, which forms an integral microstructure, and ensures high strength of CAP product for ironmaking.IntroductionLarge reserves of specularite iron ores have been found all over the world, especially in Minas Gerais of Brazil, Xuanhua city and Anshan city of China, Elba island of Italy, St.Gotthard of Switzerland, Cumberland of Britannic, and so on. The specularite ores have a smooth surface, as well as a good crystallization and dense texture. When specularite is used to produce pellets, the specularite ore grains are difficult to adhere onto green ball due to its poor ballability. Moreover, specularite pellet requires high roasting temperature over 1300°C [1]. When specularite ore is used in sintering, the permeability of sintering bed gets bad and the quality of sinter is diminished. The practice in a few sintering plants finds that the output and strength of sinter decrease with the increase of specularite proportion, and the consumption of coke increases [2-4]. Therefore, the utilization of specularite has been limited. Composite Agglomeration Process (CAP) is an innovative technology invented by Central South University [5-7]. The process has the following merits: making reasonable utilization of different iron ore resources; improving the quality and output of sinters; manufacturing sinters with low basicity; significantly reducing energy consumption, etc[8-9]. It has been shown that large proportion specularite ores, as high as 40%~50% can be used well by CAP [10], but the mineralization of specularite pellet is still unknown during composite agglomeration processing. In this investigation, the induration characteristics of specularite ore pellets is studied by simulating CAP in laboratory, and the phase composition and microstructure of CAP product are also characterized by using microscope and Leica image analyzer (Germany, Leica DM RXp)."

Jan 1, 2011

By Uchil Jayagopal, M. Krishna, P .. V. Krilpakara, S. Manjunath

"There have been a pioneering efforts over the last forty years in the development of metal matrix composites (MMCs) as a new engineering materials, having improved properties, light weight characteristics and competitive costs compared to traditional materials. Following recent advancements in casting technology and the use of melt stirring device by foundries, discontinuously reinforced MMCs where prominent alloys are reinforced with particulates or short fibres and the being employed ·in the production of castings targeted for automotive and aerospace application.The ZA-27 alloy has a high strength compared to zinc or alluminium alloys with a lower melting temperature. The main objective of the present research is to study the effect of quartz particles on the mechanical behaviour of ZA-27 alloy composites. The results showed that the ultimate tensile strength, hardness, Young's modulus of the composite gradually increased with increase in the weight percentage of the quartz reinforcement. However overall ductility decreased with an increase in quartz reinforcementIntroductionMetal matrix composite (MMCs) offer outstanding benefits as they combine metallic properties with ceramic properties there by yielding improved physical and mechanical properties.1Among the various type of MMCs particulate reinforced composite are the most versatile and economical2. By suitable choice of metal matrix and particulate system a wide range of properties combination can be obtained such as strength, modulus, fiiction.al resistance, tribological performance and machinability. These composites are capable of replacing conventional alloys in a considerable range of applications. They also offer significant saving in energy and resources"

Jan 1, 2000

By A. Rojo, N. J. Ramirez, J. E. Salgado

"This work aims to characterize the plastics used in a handgrip located in the car interior body in order to improve its design process and be able to predict its behavior when the part is subjected to impact test involving human casualties.Through stress analyses at high speeds and a video camera set up (front and side view), the reduction of area of specimen was obtained from image analysis, allowing to get the stress-strain real curve of the material.Continuing the characterization process a set of impact test was developed, where standard lzod configurations were used in unnotched specimens. From these tests were gotten displacement curves and absorption energy estimations.The proposed testing procedure allowed the acquisition of force and displacement data through time at various strain rates which are indispensable for the characterization of dynamic events. Using a specimen with a special configuration has shown a more detailed dynamic behavior resulting into more accurate numerical analyses within the design process.IntroductionIn the design process, one of the many analyses which take place is the impact test of the designed part. Nowadays there are many software capable to do these kind of analysis and each industry use the one they think it is convenient for them, but also the selected software has mathematic models that help to find the solution and the simulation of the case of analysis. These are not the only considerations that a company has to take into account, other one is the type of information and data necessary to feed the software. For this study we are going to focus on the acquisition of these data.The mail reason of this work is that generally the supplier gives the card of the material with all the characteristics and information requested by the buyer, but all of that information is acquired by standard methods, but it is inconvenient when the materials are polymers."

Jan 1, 2011

By Yuanyuan Zhang, Patrick J. Masset

"The reduction of FexO in slag is one of the fundamental reactions in iron and steelmaking technology, including the blast furnace process (BF). Experiments on the reduction reaction of iron oxide using CaO-SiO2-Al2O3-FexO-C mixtures were carried out using thermogravimetric analysis (TGA) under reducing conditions at temperatures up to 1100°C. The composition of the primary slag was chosen so that the FexO concentration varied between 0 and 75 wt % and the CaO/SiO2 ratio being kept constant to 0.90. From the TGA curves recorded isothermally at different temperatures the kinetic parameters of the iron oxide reduction were determined.IntroductionIn blast furnace the iron ores and coke are charged in layers from the top. The reduction of iron oxide by coke is one of the fundamental reactions in the blast furnace process. Although a great amount of work has been done on the topic of reduction of composites [1, 2, 3], gasification of carbon [4, 5] and reduction of iron oxides by CO [4, 5, 6], the mechanism of reduction in iron oxide - carbon powder mixtures is not fully understood. Fruehan [1] and Rao [2] studied the reaction rate of the reduction of iron oxide by different types of carbon and concluded that the reaction mechanism is controlled by the oxidation of carbon at temperatures up to 1200°C. Rao [2] studied the reaction of hematite with graphite as carbon source up to 1080°C. An activation energy close to 300 kJ/mol was calculated within the temperature range of 950°C to 1087°C. In his study, Fruehan [1] determined the rate of reduction of Fe2O3 and FeO by coal, coke and coconut charcoal as carbon sources within the 900°C to 1200°C temperature range. He found that the reduction of Fe2O3 by carbon occurs in two stages and that the reduction of Fe2O3 to FeO is faster than that of FeO to Fe. This is due to the fact that the CO2/CO equilibrium ratio is higher, and hence, the rate of oxidation of carbon is faster. Fortini and Fruehan [3] have studied the reduction reaction of wustite by graphite and wood charcoal. They found that the wustite reduction can have a significant effect on the overall rate of reduction in composites at high temperatures or in the presence of a large excess of carbon. The calculated activation energy of the reduction reaction by wood charcoal was close to 368 kJ/mol, while the activation energy of the reduction reaction by graphite was 444 kJ/mol."

Jan 1, 2011

By T. H. Courtney, B. R. Murphy

"Nominal room temperature mechanical alloying (MA) has been used to synthesize the high melting temperature NbC and Cu-NbC composites. Elemental powders of Cu and Nb were alloyed in the presence of either graphite or hexane to form nanocrystalline NbC or a Cu-NbC composite. Through control of hot-isostatic-pressing (H/Ping) parameters, we have been able to minimize microstructural coarsening during densijication, and have processed fully dense bulk compacts of both single phase NbC and two-phase Cu-NbC while maintaining a nanocrystalline or near-nanocrystalline structure. These materials generally exhibit high strength and low fracture toughness. However, mechanical properties vary significantly depending upon the Cu content and the method of NbC synthesis (graphite or hexane).INTRODUCTIONMechanical alloying (MA) has been recently used to synthesize a variety of inorganic solids; sulfides (1-2), nitrides (3), borides (4), and carbides (3, 5-8). One advantage of this processing route is that synthesis of fairly high melting temperature materials takes place at what is nominally room temperature. Another advantage is that the structures generated are often nanocrystalline in scale, with attendant interesting properties. The consolidation of these fine structures into near fully dense or fully dense materials while limiting microstructural coarsening is a challenge that has just recently seen limited success (5, 9). We report here on some recent studies of ours dealing with crystallite size and structural analysis of NbC and CuNbC composites consolidated to full density from mechanically alloyed powders. Bulk mechanical properties and their dependence on milling parameters are also presented."

Jan 1, 1994

By Zhijing Zhang

The management of hazardous wastes is important in a society which is increasingly concerned with environmental issues. Incinerators such as the slagging rotary kiln are widely used in the treatment of hazardous wastes. However, in order to assure a smooth operation of the rotary kiln, the melt should have both a low melting point and high fluidity. In this study, the fluidity of various hazardous waste rotary kiln slags was measured in terms of length of flow using the crucible test technique. It was found that the slags have melting points ranging from 1372 to 1424°C while their fluidities varied from 61-102 mm. The effect of addition of oxides on the fluidity of a slag containing 47 wt% SiO2 was also investigated. For this slag, additions of SiO2 (up to 56 wt%), FeO and Na20 increased fluidity, whereas the addition of CaO and A1203 resulted in lower fluidity values.

Jan 1, 2002

By M. Ide, K. Takemura, S. Taenaka, K. Shinzawa

"The laser characteristic is strongry dependent upon the stoichometry of forsterite (Mg2Si04) and YSO (Y2Si05) single crystals, because of change in the valency and occupied sites of doped Cr in the lattice so that mole ratios of Mg0/Si02 and Y203/Si02 in the above single crystals must be precisely analyzed. In this study ICP-AES was applied for analyzing the mole ratios. Emission intensities corresponding to Si and Mg or Si and Y were measured at the same time with internal standard method. Preparation of sample solutions, measurement conditions of ICP-AES and interferences by coexisting components were discussed, resulting in excellently precise detennination of stoichometry of the above single crystals.IntroductionIn conventional stoichiometric analysis of single crystals, the stoichiometry is detennined by analyzing each component separately with titrimetry and gravimetry techniques. On the other hand, by stoichiometric analyses using ICP-AES, emission intensities corresponding to components are measured at the same time with internal standard method. Consequently erros caused by variation of analytical condition are canceled out.Cr-doped Mg2Si04 and Y2Si05 syngle crystals are known as laser materials. The change of valency and occupied sites of doped Cr affect the characteristic of single crystal as aleser materials. The change of state of doped Cr.Stoichometric composition of Mg2Si04 is constructed by 2mole of MgO and 1mole of Si02, and Y2Si05 is constructed by 1mole of Y203 and 1mole of Si02. In this study, required analytical precision in component mole ratio is within an error of 0.0010 for Mg2Si04 (CV=0.05wt%), and within an error of 0.0030 for Y2Si05 (CV=0.05wt%) (Table I )."

Jan 1, 1998

By E. M. Weenink

One of the new direct smelting technologies for the production of lead from sulfide concentrates that has reached the commercial stage is the Outokumpu lead flash/electric furnace ?smelting process. Using data from pilot plant test work, energy and mass balances for a commercial plant were initially calculated by hand. To optimize process conditions, a large number of such balances had to be generated and a computer program using Lotus 123 was developed which provided an excellent opportunity for computer simulation. Operating parameters can be calculated by iteration using input values for feed composition, feed rate, smelting temperature, and lead content of the slag'" The output is presented by means of various views of the appropriate process steps, or in 68 different graphs.

Jan 1, 1990

By Levente Becze

The zinc bottom dross is obtained as a by-product from hot dip galvanizing operations and contains at least 92 % zinc, which is recycled mainly by pyrometallurgical processes. The overall costs of such a treatment, however, are often relatively high, and the very strict environmental protection regulations might also cause additional difficulties for the high temperature procedures in the future. Therefore, a novel hydro-electrometallurgical process has been developed in our laboratory, by which one can reclaim zinc of high purity, while attempting to achieve low energy consumption and making allowances for all the environmental restrictions. This aqueous processing technique, based on electrolytic refining in a cell equipped with anion-exchange membrane to separate the anode and cathode compartments, allows the indirect purification of the anolyte. Zinc is dissolved from the anode along with some of the impurity elements, while the intermetallic compounds (Fe-Zn, Fe-AI- Zn) are accumulated in the anode slime.

Jan 1, 2003

By Guo Chang Jiang

In order to improve the IIAZ toughness of X-60 pipe steel, the intragranular ferrite plate (IFP) technology was used. The characteristics of IFP is claimed to be much fine ferrite plates appear inside the original austenite grains. By means of suitable Re, Zr, Ti additions in a bath with a higher initial oxygen potential, a good control of the peak temperature and the cooling rate during welding simulation, one can get a %IFP in volume over 50%, and the toughness gets up from 55 J to 160 J. It was found that the inclusions most effective in nucleating IFP are some deformable complex silicates which either entrap Re, Zr, Ti oxides or contain these elements. The greater the number of the evenly distributed and effectively nucleating inclusions, the more the %IFP in volume, and the finer the microstructure of the HAZ, so the better the relevant toughness. Generally, these silicates bahave as fine spheres along a line. The present authors revealed that these fine spheres result from the remelting of the shuttle- like silicates due to heating in the process of welding simulation. These silicates used to get a higher sulphur capacity, so MnS deposits might be observed on the periphery of the silicates. IFP was proved to be directly rooted in the [Mn] depleting zone which locates beside MnS deposits.

Jan 1, 1997

By Zengjie Wang

Investigation on hydrochloric acid leaching of the ilmenite from Panzhihua, China was carried out to prepare synthetic rutile. The leaching parameters were optimized to obtain high content of TiO2 in the products. The experimental data suggest that an optimum leaching can be realized with 30% acid, a solid/liquid ratio of 1/4 at 95°C for 4h, and ore ground for -400 mesh size. After the acid leaching, an additional alkaline leaching process using hot NaOH solution was performed, and then the products was in grain form followed by heat treated at 900°C for 2h in order to extract Si and increase the particle size of synthetic rutile. The final product has a high content of TiO2 (about 95%), a low content of chlorine consuming elements (total CaO+MgO =0.07%) and a suitable particle size distribution for chlorination process.

Jan 1, 2008

By Wei-Tong Du, Yu Wang, Gang Wen

Carbon dioxide (CO2), a major component of the greenhouse gases, could be comprehensive utilized as a valuable resource to oxidize vanadium during the converter vanadium extraction process. The thermodynamic software, FactSage, was utilized to study the oxidation ability and theoretical cooling ability of using weak oxidant CO2 as coolant in vanadium-containing hot metal. Besides, experimental research on vanadium extraction in CO2 and O2 mixed blowing extracting process had been undertaken. The results indicated that the elements C, Si, V, Mn etc. could be oxidized by weak oxidant CO2, and the content of V2O3 in slag was approached to pure O2 blowing. Furthermore, CO2 had a remarkable cooling ability and the molten bath temperature kept on decreasing as CO2 blowing rate increases. This research has proved that CO2 and O2 mixed blowing in vanadium extraction process are effective.

Jan 1, 2015

By Itavahn Alves da Silva, Izabela Diniz Duarte, Carlos Antonio da Silva, Varadarajan Seshadri

Mathematical modeling using computational fluid dynamics has been employed to assess the thermal losses in a steelmaking ladle. Thermal losses lead to thermal stratification and convective flow inside the ladle. The effects of preheating, mineralogical and physical characteristics of the lining as well as thickness of slag cover have been studied and the results obtained from application of the model have been discussed.

Jan 1, 2016

By Li Kaihua, Li Liang, Miao Qingdong, Wang Cong

The current process of production of titanium sponge involves the use of TiCl4 as a feed material and a huge amount of heat is generated during the magnesiothermic reduction process. For this reason, it is possible to agglomerate into a titanium lump with the partial high temperature. And, it is difficult to obtain soft titanium sponge with low content of impurities. In order to solve the current problems in the titanium sponge production process, process optimization experiments study of TiCl4 feeding speed, vacuum distillation temperature, system pressure and time control had been conducted for obtain high quality titanium sponge. Experimental results show that lower feeding speed can improve the output capacity of titanium sponge and softer products can be obtained. The product grade rate of titanium sponge improved significantly.

Jan 1, 2015