Search Documents

By Deren Zhu

Based on the results of field observation and physical model analyses, a computer simulation method, FEAEBP, has been developed for simulating the breakage of the main roof by considering it as a Kirchhoff plate on Winkler elastic foundation. By this method various parameters of rock property, different boundary conditions of the working face and the initiation, development and results of the breaking process of the main roof with different geometric dimensions can be effectively simulated. Since the main and immediate roofs, and the coal seams are treated as an integrated mechanical system, the interaction among them can be studied in detail.

Jan 1, 1988

By Mingju Liu

In this research, we measured fractal characteristics of over ten typical outburst areas on different scales and related them to their outburst proneness, in attempts to provide new methods for outburst prediction. It was shown that both faults and folds follow the power law on coal basin scale, mine scale or mining district scale, whichever it is. Fractal dimensions are appropriate indices to describe geological structures quantitatively. Preliminary relationships have been established between outburst proneness and fractal dimension. Comparisons have been made among fractal characteristics and degrees of outburst proneness on all three scales. The results indicate that multi-scale assessment of outburst proneness can be made based on fractal measurements independently or supplemented by other assessment methods.

Jan 1, 2000

By Neil Styler

This paper presents an analysis of measurements of inter-burden de- formations above six longwall faces. An attempt is made to demonstrate some correlation between the movements at the various sites, and to examine their importance with respect to predicting caving height, disruption of overlying seams, and disruption of aquifers. This analysis demonstrates some significant differences between predicted surface subsidence, and inter-burden deformation. In addition it is shown that the caving height above a longwall face is equal to 8 to 12 times the extraction height, with a zone of fractured rock ex- tending to approximately 50 times the extraction height above the seam.

Jan 1, 1984

By Xianming Zhou

Mining economics is such that too conservative in safety will result in a considerable penalty in mining cost. However, initial planning and design of a mining project often must be done without complete information. The assurance of economical and safe mining is thus difficult. This study is focused on the improvement of the mine design associated with Zhaoyuan Gold Mine in P.R. China as more information becomes available. Attention is given to the selection of backfill structures. Based on a proposed practical finite element model, a design, which is believed to be not only reliable but also cost-effective, is recommended for further mining operations in this mine.

Jan 1, 1989

By Tetsuro Esaki

This paper describes the present condition of mining-induced damages in Japan and the characteristics of them. The change of mining operation and environmental condition has caused various significant impacts on the ground environment: subsidence, cave-in, springing out of ground water etc. The characteristics and the influences of these phenomena are discussed by investigation of the actual conditions and by fundamental studies. Some counter measures are also introduced.

Jan 1, 1989

By Jinsheng Chen

For underground openings, many factors can cause roof failure and thus roof falls. The most common factors related to Mother Nature are weak roof lithology, geological structures, and an abnormal in-situ stress field. Theoretically, any underground opening can be successfully supported under any geological and mining conditions if the opening width is limited and the roof supporting system is well designed. However, roof control cost must be taken into account. In practice, to minimize the roof control cost, different roof control plans have to be considered to take care of the uncertainty or variation in geological and mining conditions. For most underground mines, it is unsafe or economically unrealistic to use one fixed roof control plan for the entire mine. Therefore, local, abnormal geological and mining conditions must be identified and a site- or area-specific roof control plan must be employed. This study tries to identify the major factors that have significant impact on entry roof stability by analyzing the historical roof fall data at Rofomex mine. Finally, the appropriate roof control plans or roof bolting systems for different geological and mining conditions are recommended.

Jan 1, 2011

By Kevin MacPherson

After 34km of roof bolted drivage the first fall of ground occurred at the Phalen Colliery in the maingate of the 8th East longwall panel. The fall occurred over the stage loader as the wall approached an area of poor roof geology. This area had developed a severe cutter since initial drivage and the longwall had yet to mine through 500m of even worse conditions. This paper describes the cause of the poor roof conditions, the use of polyurethane resin injection and cable bolting to re-stabilize the roof outby the fall, and the measurement of roof movement and performance subsequent to the continuation of mining under the rehabilitated roof.

Jan 1, 1999

By Douglas Morrison

By applying modern 3D numerical modelling techniques to the analysis of a pillar cascade failure in a room and pillar mine, it has been possible to simulate the collapse and develop an understanding of the role of low rock strength areas within the mine. The cascade collapse occurred in a normal strength area but would not have occurred without the influence of a low strength rockmass in one section of the mine. The numerical analysis made it possible to develop a realistic assessment of the residual pillar strength. With the introduction of regular empirical pillar performance assessments, critical pillars or groups of pillars can now be identified proactively. This has led to an aggressive extraction ratio of 90% that manages pillar failure, avoids pillar and roof collapse and prevents surface subsidence. Since the mine also has significant waste products, the use of backfill for ground support has made it possible to significantly improve the performance of strategically located pillars, and so achieve even higher extraction ratios.

Jan 1, 2003

By Hamid Maleki

A novel ground control program has been developed at Plateau Mining Company through five years of geotechnical investigations. The study was initiated to determine the causes for roof stability problems and to develop alternative support and monitoring systems for increased safety and productivity. From systematic roof fall observations, extensive geologic mapping, roof drilling and monitoring ground movements along gate entries of four longwall panels, a sand- stone channel system was detected and shown to impact roof stability. In particular, underlying mudstones up to seven feet thick experienced instability due to differential compaction and load transfer from the gob. Roof bolter operators were trained to report roof lithology for mapping channel positions into the roof and for selective use of longer bolts. This boosted operator morale, and improved ground conditions. Monitoring rates of roof movement is used in these areas for detection of instability and for application of secondary support: This has significantly increased safety and productivity.

Jan 1, 1987

By Kikuo Matsui

Standing supports such as steel arches or square work supports along with the necessary struts and lagging have been traditionally employed in the longwall gateroads of the Japanese underground coal mines. Miike Colliery has newly introduced the interpanel-pillar mining system and the strata bolting system in gateroads to raise productivity levels and reduce operating costs. The Department of Mining Engineering, Kyushu University, in cooperation with the Miike Colliery and the Coal Mining Research Center, Japan (CMRCJ), has been conducting research into the optimum design of strata bolting as a primary support system in longwall gateroads. This paper presents a brief overview of the current state of strata bolting technique being applied in longwall gateroads at the Miike Colliery and discusses some problems in employing bolting.

Jan 1, 1993

A procedure fm the estimation of pilla1 strength is presented where the design of underground coal pillars is emphasized. An analytical approach has been developed, proposing that the effect of end constraints on the pillar strength and the ductile behavior of coal material should be incorporated in the computation of the stability of coal pillars. Bad on this approach, it has been found that end constraint has a significant influence on the pillar strength. The study indicates that when the end constraint is zero the computed strength of the pillar is the same as the unconfiied compressive strength of the coal mass and will not increase with the increase in the width to height ratio. However. when the end constraint is greater than zero the pillar strength will increase exponentially as the width to height ratio increases.

Jan 1, 1990

By Duk-Won Park

A vast majority of the operating longwall sections use shield-type face supports to provide ground control in the United States. As a co-operative research program between the University of Alabama (UA) and Jim Walter Resources, Inc.(JWR), a joint research program is underway to study interaction of shields with surrounding rock masses. A series of analyses on the response of shields are performed using monitored data at a longwall face in a deep coal mine. In this paper, various effects of parameters, such as leg pressure, setting load, developing load, maximum loading rate, pressure in capsule, and convergence between canopy and base, are discussed and recommended as stability indices. A microcomputer program is being developed for instantaneous interpretation of the shield monitored data, and for giving warnings of potential problems. The preliminary results define the effects of the setting load, developing load, and rate of developing load or leg closure rate. The objective of the study is to understand the shield characteristics and their interaction with surrounding strata in real time, then develop a reliable program for maintaining longwall stability.

Jan 1, 1992

By Douglas Morrison

Hardrock mines in Ontario generally operate at between 3,000 and 7,500 ft below surface and generally experience significant rockburst activity below 5,000 ft. Since the introduction of bulk mining techniques around 1980, the safety record of Canadian hardrock mines has improved dramatically. However, the process of improvement was not a smooth one and, in the early years, the number of accidents and fatalities actually increased. One incident in 1984 that resulted in 4 fatalities in Ontario initiated a complete re-examination of mining practice and by the mid 1980s many changes had been introduced, driven by new non-prescriptive mining legislation. These changes affected not only the technical discipline of mining engineering but also the management of operational procedures and, together, they resulted in the significant improvements that have continued to this day. The analysis of the rock-fall related fatalities showed 5 major causes (loose, scaling, installing support, collapse and rockburst) and by the mid 1990s fatalities in all of these categories, except rockbursting, had been eliminated and even then, all these rockburst fatalities occurred in one mine which was closed shortly afterward. This paper discusses both the technical and social reasons for the initial failure and the ultimate success in improving the safety of these mines, with implications for mines in other major mining jurisdictions.

Jan 1, 2003

By A. Mahyera

BETTER ROOF SUPPORT During the last decade, resin-grouted roof bolts have taken a substantial foothold in the coal mining industry - now accounting for about one-third of all bolts installed annually, due to the improved roof support. However, the high cost, toxicity and flammability of the resin cartridges appear to be a limiting factor in even greater use of such bolts. Terra Tek, Inc. has, over the past few years, been developing a novel roof bolting system to mix/inject a very fast-setting and high strength inorganic cement into bolt holes and install point-anchored or full-column grouted rebars - all automatically and at substantial cost savings. This grouting system utilizes a unique method to mix the grout ?in-the-hole?. It has been integrated with a conventional bolter, retrofitted with an indexing-head mechanism and an on-board pneumatic computer to sequence and Control the drilling, grouting and bolting. Cycle times are the same or better than for a resin system. Following laboratory testing/development, the prototype system has undergone field trials in a Utah coal mine. A description of the bolting system, results of pull-tests in the laboratory and field, and economics and productivity gains with this system in comparison to a conventional resin-cartridge bolting method are presented. The relationship of this technique to improved roof control is also discussed.

Jan 1, 1984

By Anthony T. Iannachione

The location and time of 2,007 microseismic emissions from a limestone mine in southwestern Pennsylvania were compared with the development of mine faces and the characteristics of the mine layout. Based on analyses of these results, the occurrence of roof failure zones appears to be associated with certain characteristics of the mine plan. It was determined that significant relationships exist between the intensity of the microseismic activity and the scale of the roof failures. Microseismic activity associated with these roof falls occurs in distinct episodes, with the final failure event occurring during approximately a 12-hour period. Each roof fall episode appears to be composed of dozens of distinct roof beam failures. As each beam fails in shear and tension, tens to hundreds of audible noises representing rock fracturing or bedding plane separation can occur. While every roof fall can be viewed as unique, certain mechanistic similarities can be realized through careful observation and monitoring of these complex systems. Understanding these similarities in characteristics allows mine personnel to design the most effective and efficient control technique.

Jan 1, 2001

By John Stankus

Accurate evaluation of stress and geological conditions is critical to ground control design in underground openings. For a mine slope entry, the problem becomes more complicated because a slope transverses through many different types of strata. Mine slope ground control has traditionally been practiced based on trial and error and prior experience. There is currently no well-accepted slope and support design methodology available for an economical and technically sound ground control plan. Over the last few years, Keystone Mining Services, LLC (KMS), the engineering affiliate company of Jennmar Cooperation, has developed a ground support design methodology called the ?Stress, Geologic, and Support design system? (SGSSM). This patent pending method enables accurate analysis of actual geo-technical conditions and stress; identifies strong, fair, and weak sections along the slope; formulates primary and supplemental roof bolting systems, designs optimal long-term steel structure support; and verifies the adequacy of the developed support. The method has been successfully utilized on various new slope projects and has been well received by state and federal regulatory agencies during the approval process. This paper details the concepts of the methodology using an actual case study of a slope project in the Midwest.

Jan 1, 2011

By Axel Preusse

Stowing or waste fill is common in the German mining industry since the beginning of mining activities, With increasing mechanization, flat and gently inclined seams (0 -- 18) were mined. These mines were located within the densely populated areas close to important infrastructures such as industrial complexes, roads, highways, railroads, rivers and canals. These buildings and infra¬structures were rarely protected against subsidence influences and other ground movements and dump capacities close to the mines were exhausted. For subsidence reasons and because of the low dump capacities pneumatic stowing methods were continuously developed and used in German longwalls until 1997. Due to techni¬cal standards and because of some restrictions pneumatic stowing in Germany is only used at a minimum seam thickness of 2.00 m and average costs of this method are $20 - 30 per ton. A significant reduction of the disturbance potential and by that a decrease in expenses for subsidence regulations due to reduced subsidence and ground movements could not be achieved. In this paper the experiences with pneumatic stowing in the Ger¬man mining industry are described. Possible subsidence reduction and economic aspects of pneumatic stowing are taken into account.

Jan 1, 2002

By Y. Luo

An extensive subsidence research program conducted by the authors has greatly improved the accuracy and the capabilities of subsidence prediction under complicated mining and surface conditions. The techniques developed for assessing and mitigating subsidence influences on various surface structures have been applied in numerous cases with a very good re- cord of success.

Jan 1, 1997

By K. Itakura

Information about geostructure for effective rock bolting must be obtained before setting the bolt into rock in a coal mine roadway. Especially, rock type variation and distribution of discontinuities such as layer boundaries, and separation of strata and cracks all represent indispensable knowledge. To achieve in-situ evaluation of roof rock, we developed an MWD (measurement while drilling) system using mechanical data from a drilling machine for rockbolt. System hardware detects torque, thrust, revolution, and stroke of the machine, and software analyzes the mechanical data log and displays locations of discontinuities using Neural Network techniques. Also, this system is able to estimate roof rock 3-D geostructure for varied rock types and discontinuity distribution in cases of a drill hole array arrangement in roof rock. We conducted a feasibility study for it using hydraulic drilling at roadways of the Taiheiyo Coal Mine, Japan. Simultaneously, some core drillings were also performed to confirm system analysis data. For core samples, distribution of cracks was observed and the borehole wall was investigated by OFS (optical fiber scope). Must discontinuity locations estimated from roof logging were conformed with data obtained from core inspection. However, the core sample contained a number of cracks which were not found in the mechanical data log. This indicates that additional cracks were generated during and/or after core drilling by the influence of rotational force of the machine and water supply. Furthermore, in comparison with the OFS image, resolution of the discontinuity's log estimated by this system was clarified; that is, it is difficult to detect small size cracks (hairline cracks) from a mechanical data log and the core inspection by OFS. This paper outlines the new hardware system for hydraulic drilling machine and compares the discontinuity map obtained from the software system with drilling core inspection.

Jan 1, 2001

By Olayemi Akinkugbe

As coal production in the United States continues to increase, the availability of unexploited or virgin fields continue to diminish. As a result, mine operators are forced to mine in unfavorable or multiple seam conditions. The safe, productive exploitation of coal in multiple-scam conditions requires specific design technology. At present, there are two general design approaches that the mining engineer can use to analyze the multiple-seam problem in question, either simple empirical relationships or complex numerical models. Often, the empirical approaches are too general for the specific problem and the numerical models require too much time and expertise for the practicing engineer. This paper introduces a new computer program, Lam2D, designed specifically to enhance multiple seam mining operation by quickly and easily calculating, stress, displacement, subsidence, horizontal strain and safety factors associated with multiple seam mining situations. The program implements a simplified, two-dimensional boundary-element method in order to model the complex multiple-seam stress and displacement interactions. Most importantly, the program is greatly simplified by incorporating automatic overburden, interburden, coal and gob property generation thereby reducing typical modeling and solution time to a few minutes.

Jan 1, 2004