Search Documents

By S. Ersayin, I. Iwasaki

Laboratory- and pilot-scale tests were carried out to study the effects of a magnetically enhanced hydroseparator on a magnetic taconite sample. The test parameters included feed flow rate, percent solids and magnetic field strength. Laboratory tests showed that magnetic iron losses could be effectively prevented by applying a magnetic field strength of 0.003 T (30 gauss) to a hydroseparator. A relatively uniform magnetic field within a pilot-scale hydroseparator was obtained by installing a magnetic grid within the device. The test parameters for the pilot-scale study also included the effects of magnetizing/demagnetizing the feed and magnetizing current. Magnetic iron losses were substantially reduced, even when the hydroseparator was operated at very high upward velocities. Results also show that increasing the field strength decreased the losses, but magnetic enhancement was successful even at the lowest field strengths, and the results show that magnetic iron losses were lower when the feed was magnetized. Key words: Hydroseparator, Magnetic field, Magnetic grid, Taconite processing, Magnetizing, Demagnetizing.

Jan 1, 2003

By J. A. Nelen, R. B. Cook

Panned stream-sediment, geochemistry-based gold exploration in those parts of the southeastern Piedmont proximal to the Fall Line must take into account potential contamination from basal fluvial sediments of the Coastal Plain. Anomalies attributable to the incorporation of placer gold of Coastal Plain origin into modern Piedmont drainages have been identified in portions of Lee, Macon, and Tallapoosa Counties, AL, and Baldwin and Hancock Counties, GA. Identification and interpretation of such multicyclic anomalies must be based on knowledge of the local maximum Cretaceous transgression, paleotopography, modern and paleofluvial system dynamics, and fineness trends and Au-Ag zoning in gold grains.

Jan 1, 1990

By S. C. Gambrell

Support characteristics of in-cycle trusses are analyzed using a photoelastic model loaded by tightening a truss in the sequence normally used in an underground mine. Stresses in the roof at its center point and at the junction of the roof and rib are examined. Effects of zero tension and unequal tension in the inclined anchor rods are presented. Effects of simulated subsidence on stress in the roof surface and on tension in the separate truss members are examined. Conclusions are drawn relating to (1) the effects of tension in the inclined anchor rods on uplift and compressive stress parallel to the roof surface, (2) the effects of subsidence on stress in the roof surface, and (3) the effects of subsidence on tension in the truss members.

Jan 1, 1987

By Zhen-lu Zhao

The manipulators possibly used in underground mining must deal with unpredictable obstacle while keeping certain positions and orientations of end effector, and in some cases, are required to possess redundant joints in order to be more flexible. This kind of manipulators might be fitted with jumbo drill or platform as auxiliary to potentially deal with some utility works in versatile way, such as installing rock bolts, guniting, blasting, charging, surveys and measuring work, etc.. This paper describes numerical procedures of performing inverse kinematic problems for redundant manipulators .The procedures, based on the generalized pseudoinverse of Jacobian matrix, are developed to lead to kinematic solution at both singularity and ill conditioning, and to guarantee continuous sequence of positions of the end effect or. Furthermore, the solution to optimization and obstacle avoidance is investigated. A numerical example is shown to illustrate the approach.

Jan 1, 1989

By Edita Vircíková, J. B. Hiskey, Ludovít Molnár, Peter Lech, B. J. Scheiner

This paper describes the results of a study of hydrometallurgical methods of producing sodium arsenate for the glass industry from arsenic oxide wastes occurring in carbon dioxide washing. This paper addresses the following aspects: theoretical assumptions for leaching arsenic and its oxides, experimental results of As(III) oxidation to As(V) in aqueous solutions, sodium arsenate crystallization (the system As2O5-Na2O-H2O), characteristics of the crystalline product, and pilot-plant tests using sodium arsenate in the glass industry.

Jan 1, 1993

By G. T. Adel, W. Z. Choi

In previous work at Virginia Tech, a population balance-model describing the simultaneous processes of size reduction and mineral liberation has been developed. Experimental verification of this model, however, has been limited to a binary mineral system containing only one composite particle class. When considering multiple classes of composite particles, estimation of model parameters becomes much more difficult. In the present work, a procedure for estimating model parameters for a multiple-composite- class model has been developed. Emphasis is placed on direct experimental determination of these parameters. The physical significance of the breakage rate function and the liberation function in characterizing the liberation process is also discussed.

Jan 1, 1987

By H. Polat, M. Polat, S. Chander

A high shear treatment step was observed to improve flotation of coal. The effect of high shear treatment (HST) was a strong function of coal rank, however. For the low rank coals the HST produced loose, open-structured agglomerates which decreased the entrapment of ash minerals. For the high rank coals, the high shear treatment promoted detachment of low-floating particles from the agglomerates that ordinarily formed in a flotation cell. The extent of agglomeration and detachment of particles from the agglomerates was a function of the amount of dodecane and coal rank. To obtain desired efficiency of separation ethylene-propylene oxide block co-polymers were used. The results showed that the HST-flotation technique increased the ash rejection considerably for both high and low rank coals, though the mechanisms were different.

Jan 1, 1995

By J. M. Kruger, P. Berendsen, A. Martinez

High-resolution ground-penetrating radar (GPR) was used to image the near-surface extent of two exposed Late Cretaceous kimberlites intruded into lower Permian limestone and dolomite host rocks in northeast Kansas. Six parallel GPR profiles identify the margin of the Randolph 1 kimberlite by the up-bending and termination of limestone reflectors. Five radially intersecting GPR profiles identify the elliptical margin of the Randolph 2 kimberlite by the termination of dolomite reflectors near or below the kimberlite's mushroom shaped cap. These results suggest GPR may augment magnetic methods for the delineation of kimberlites or other forceful intrusions in a layered host rock where thick, conductive soil or shale is not present at the surface.

Jan 1, 1998

By Natesa Jayaraman, Jon C. Volkwein, Edward D. Thimons

The Bureau of Mines has studied the impact of shuttle car movement on face ventilation. Real-time measurements of air velocity, methane gas, and respirable dust were recorded and compared with a time study of face shuttle car movement. Work was conducted in a blowing face ventilation section where a scrubber-equipped mining machine operated. Air velocities decreased by an average of 35% as the shuttle car entered the face, restricting air flow, and increased by an average of 35% as the shuttle car pulled away from the face, drawing with it additional air. Return air methane levels follow the face air flow volumes, decreasing as air volume increases. The surge of air created as the shuttle car leaves the face helps to dilute methane. Respirable dust levels, however, were found to increase as the air flow increased and decreased the scrubber capture efficiency.

Jan 1, 1989

By Allen V. Reicks, Thomas J. Rudolphi

Computerization has allowed practical design of complicated and optimized belt conveyors for bulk materials from prediction of belt tensions around the belt circuit for a wide range of belt loadings and conveyance paths. These design methods are based on a knowledge of component operating characteristics and sources of tension change. As compared to generalized 'f' methods, CEMA's historical Kx and Ky has provided nonlinear and more specific predictions of belt tension as affected by various components and operating conditions. These empirical values were developed in a different age and generalizations made in their development are now a constraint to additional conveyor improvements. This paper discusses the potential from improved and standardized ‘friction’ predictions and presents the results of sensitivity evaluations as affected by calculation method

Jan 1, 2004

By Donald S. Clarke

The Umuna epithermal precious metal deposit has provided the target for a simulated rock geochemistry exploration program, directed at bedrock exposed in the drainage system of eastern Misima Island. A geochemical halo to the deposit is readily recognised in the mafic meta-volcanic country rock. This halo is defined by anomalous results for both major (K, Na, Ca, Mg) and minor (Au, As, Sb, Cu, Pb, Zn, Ba, Rb, Sr, Cs, Bi, Ga, S) element geochemistry, extending further than 1km from the deposit. Such halos are sufficiently extensive to provide adequate exploration targets in the search for epithermal mineralisation, complementing mineralogic and secondary media geochemical investigations.

Jan 1, 1989

By Tom C. Palanglo, Norbert Maerz

Control of crushing and grinding circuits ideally requires continuous particle size measurements on both in- and outgoing streams. Until recently, size distributions could only be obtained by screening methods, which were neither cost effective, frequent enough, nor timely. Input streams are often composed of large fragments, making screening prohibitive. Optical image processing systems, such as the WipFrag System, have been developed to the point that they are an extremely valuable tool to characterize, control, and fine-tune the comminution process. Although accuracy is less than that of screening, measurements are precise enough to detect relatively small changes in size distributions.

Jan 1, 2000

The declining grades of surface deposits have re-confirmed the need for greater production rates. Large scale production requires increased investments in expensive and sophisticated equipment. The key to successful operations can depend entirely on proper equipment utilisation and in this program of research at the Department of Mining and Metallurgical Engineering, University of Queensland, much emphasis has been placed on the analysis and improvement of this aspect of a load-haul-dump operation. For a model to be successfully integrated into a mine engineering function and readily accepted by mine operating personnel, it has to offer more than just results. The concepts used in its design and construction must include sufficient detail to enable engineers to apply it usefully and with confidence.

Jan 1, 1979

By John Durkin, Steven Wirch, Fred N. Kissell, Steven Ruggieri

The Bureau of Mines has developed two expert systems to give advice on coal mine dust control, one for continuous miner sections, and another for longwalls. Prototype versions have been evaluated by coal operators and MSHA. Both systems query the user as to the nature and extent of the dust control problem. Typical questions asked deal with matters such as cutting sequence, current dust standards and characteristics of current dust control techniques. Advice given by the system generally does not focus on a single issue, but may suggest a variety of approaches consistent with the ability of the operator to practically implement what is suggested. Both were written using expert system development software called Insight 2+. The advantages of Insight 2+ for the user are: low cost, IBM-PC compatibility, and the fact that little prior experience with computers is required. For the developer, Insight offers an easy to use production rule language and goal driven structure as well as a wide variety of capabilities.

Jan 1, 1987

By Subash Chander, B. Arnold

Many developments have occurred in coal flotation with regard to increasing recovery from the flotation circuit and its impact on overall coal preparation plant recovery. This includes innovative design of flotation circuits, equipment modification and development, methods of enhancing the use of reagents, effect of slimes, and recognizing the effect of water chemistry. This paper will review recent advances and present some guidelines to improve process efficiency.

Jan 1, 2005

By B. Cavender

The operating lifetime, or production rate, selected for a mining project is among the most important factors influencing the project's design and ultimate economic success. Incorrectly-determined lifetimes can lead to the erroneous rejection of projects as uneconomic as well as the suboptimal exploitation of producing properties. This paper examines the optimal lifetime calculation using traditional discounted cash flow and recently-proposed option pricing techniques. Using each method, the production rate is determined as that rate at which the project's net present value is maximized.

Jan 1, 1993

By R. Hogg, E. Kaya

The presence of agglomerated particles in airborne dust in coal mines has been confirmed by SEM examination of static samples collected on substrates. In addition, the effect of agglomerated particles on the performance of cascade impactors and cyclone- type personal samplers has been studied. Simple procedures have been developed for evaluating the extent of agglomeration in air-borne dust by comparing the observed size- selectivity of the sampling devices with that expected under idealized conditions. Applications of these techniques in the laboratory and in underground mines are discussed.

Jan 1, 1992

By M. C. Williams, T. P. Meloy

For over thirty years the Population Balance Model, PBM, has been the mainstream modeling method for comminution unit operations and comminution circuits. For commercial comminution circuits the method is based on erroneous physics and dubious numerical mathematical methods leading to non unique solutions that have little extrapolative value and faulty control strategies. In short the PBM is wrong. Given is a detailed analysis showing a number of non trivial flaws in the linear PBM. Moreover, a simpler model is presented that leads to a solution of the comminution circuit predicting the size distribution output over a variety of conditions. Because the linear PBM is firmly entrenched, an award is offered, $10,000, to any researcher that can use the linear PBM and its present numerical methods to predict the typical straight line, self similar, output of wet mills over a variety of grinding times.

Jan 1, 1992

By R. D. Hansen, R. R. Klimpel

This paper discusses the influence of frother type and dosage on recovery/selectivity in coal/sulfide mineral flotation as a function of particle size. It is shown that different frother structures exhibit quite different but consistent performance characteristics depending on the underlying particle size ranges involved as well as the dosage levels of both the frother and collector. The data presented on existing commercial frothers and some new special purpose experimental frothers is used to illustrate some general operator guidelines on proper frother selection and use.

Jan 1, 1987

By P. Mousset-Jones, F. Calizaya

This paper explains and discusses a computer program that has been developed to determine the ventilation design parameters for complex auxiliary ventilation systems such as those found in the construction of long excavations with multiple headings. The program is based on the principle of partitioning the system into segments of finite length, and formulating and solving the resulting networks recursively. The resulting network problems are solved analytically. With this program, the size of fans can be determined in order to reduce the total leakage and minimize the flow recirculation. The application of the program is illustrated by the detailed solution of an auxiliary ventilation system proposed for the Exploratory Studies Facility (ESF) at the Yucca Mountain Project, Nevada.

Jan 1, 1995