Search Documents

By D. G. Kotlyar

Silver is an economically important component of many complex, massive sulfide ores. Current beneficiation for these ores is almost entirely by flotation. Silver recovery often is low, but little is known about the flotation behavior of the silver-bearing minerals. Floatability studies were conducted using silver-bearing tetrahedrite and lead-zinc ore. The effects of xanthate collector concentration, conditioning time, potentiostatic control of the mineral potential, and pH on mineral floatability were evaluated. The floatability of the silver-bearing minerals was shown to depend on collector concentration and mineral potential. The effect of controlling mineral potential during the flotation process is discussed.

Jan 1, 1994

It is well established that the results of emulsion flotation in which water-insoluble oily collectors are utilized depend critically on the emulsification of the collector and on its conditioning with the pulp prior to flotation. The flotation tests carried out with magnesite and fluorite using sodium oleate as collector confirmed acidic and alkaline ranges of good flotation. While the flotation results in the acidic solutions depend strongly on the conditioning time and can be very much improved when longer conditioning times are utilized, the tests in the alkaline environment do not exhibit any significant dependence on conditioning. The results obtained with sodium salts of myristic and lauric acids confirm these findings. The observed effects provide additional evidence for the role of the colloidal species which appear in the acidic solutions of weak electrolyte type surfactants, such as fatty acids. The flotation properties of sodium oleate in the pH region in which it appears in the form of oleic acid droplets are mainly determined by the properties of such droplets. The flotation in this pH region closely resembles an emulsion flotation.

Jan 1, 1993

By Thomas O. Glover

History of Underground Coal Mining in Illinois The production of coal in Illinois using underground mining methods, commenced early in the 1800's; however, the first shaft entrance was not sunk until 1842. The shafts range in depth from 16 feet (4.9 m) in Peoria County to 1,001 feet (306 m) in Christian County. The earlier mines were smell, private operations that worked outcrops and shallow seams at less than 100 feet (30.5 m) in depth. By 1975, there were reported 4,076 abandoned underground coal mines in 70 Illinois counties (Nawrot, 1977). There were many more mines; however, only 4,076 underground mines have been documented. Small mining operations characterize the majority of the underground mines. There have been no significant multiple seam operations in Illinois. The most extensively mined seams were the number two, five, and six seams. Number two seam was worked in the early 1900's by 252 mines in the longwall mining region of northern Illinois (Nawrot, 1977). Available records for 2,054 abandoned mines identify 1,043 as shaft nines, 700 as slope mines, and 311 as drift mines. Some operators began reporting annually to the State Department of Labor in 1879 and by 1882 all mine operators were reporting. Annual reporting still continues to date. The information is compiled by the State Department of Panes and Minerals in their "Annual Coal Report." By the end of 1974 there were 800,000 acres (323,756 hectares) of abandoned underground coal mine workings (Smith-Stall, 1975)2 Copies of abandoned underground coal mine maps may be inspected by interested parties in the State Department of fines and Minerals office in Springfield, Illinois, or at the office of any county recorder for mines within their county. Copies of active underground coal mine maps may be inspected at a State mine rescue station near the mine site or at the county recorder's in the county in which the mine is located. Copies of active underground coal nine naps shall be open to the examination of all interested persons, but such examination shall be made only in the presence of the State mane inspector or the recorder. At the present time, the Department of Mines and Minerals has 1,746 maps of abandoned underground coal mines in its possession. These maps cover the majority of

Jan 1, 1977

By T. Luterbach, V. T. McLemore

"Trace element analysis of placer gold can be used as a valuable exploration tool in order to determine the original deposit source and locating lode gold deposits. Placer gold collected from multiple districts in New Mexico and Alaska, coupled with a broad database of previously analyzed placer gold samples indicate correlations between chemical signatures (especially gold, silver, and copper) and type of deposits (i.e., Au-rich copper porphyry deposits, Au porphyry deposits, and epithermal deposits). By completing a chemical analysis and determining the particle morphology of placer gold collected from these districts using an electron microprobe, patterns in the chemical signatures from each location can be used to examine chemical variability (1) within the individual placer gold particles, (2) within the same district and (3) among different districts. INTRODUCTION Although there are numerous past studies on the chemical composition of placer gold by Newberry et al. (1997), Melchiorre (2001, 2009), Townley et al. (2003), and McLemore et al. (2014), the gold analyzed tends to be collected from one or few specific districts. Rarely do those studies compare compositional results to additional districts, or elaborate on the correlation between the elemental composition of the placer gold and the original deposit source for the respective districts. This research analyzes the composition of placer gold from multiple districts and within the same district. There are a number of elements, which can, in various quantities, be present in placer gold particles. Native gold can be in complete solid solution with native silver and contain additional elements including Cu, As, Pb, Fe, and S. The chemical signature of the gold is determined by the thermodynamic conditions of precipitation and transport as well as the total metal content of the system. As Townley et al. (2003) explains, “These thermodynamic conditions and metal budget differ from one type of hydrothermal deposit to another, and hence different deposit types will each have a characteristic gold compositional signature.” Identifying this signature can be a highly valuable tool in exploring for gold, as it can not only be used to determine the original source deposit of the placer gold, but provide valuable insight as to the erosion level of the present deposit."

Jan 1, 2016

By P. R. Taylor

Three refractory gold concentrates have been tested to evaluate the effect of roasting with hydrated lime followed by cyanidation. The results indicate that it may be possible to roast in such a manner as to contain nearly all of the sulfur, arsenic and antimony in the roaster calcine. Cyanidation results indicate that the gold recoveries are greater than 80% for all three concentrates.

Jan 1, 1993

By James W. Cooksley

Through the early stages of metamorphism, when diffusion is the predominant mineral forming process. there is a tendency toward homogenization of rock units; but there is also zoning resulting from differing primary lithology and structure. Later stages of metamorphism, when infiltration occurs, tend to intensify zoning within the rock mass. The above concepts have been borne out in exploration of talc deposits and skarns. Initially, geologic mapping and soil sampling are directed to understanding mineralogy and petrology. Later, seismic methods are employed to further define lithology in the subsurface. Magnetometer surveys can also define some metamorphic units efficiently. Then, drilling must ensue to confirm lithology and determine extent of mineralization.

Jan 1, 1992

Growing concerns of climate change and its potential association with the release of greenhouse gasses to the atmosphere have prompted possible legislation which would require minimization of greenhouse gas emissions. Carbon dioxide and methane, both of which largely contribute to the greenhouse effect, have direct links to the fossil energy industry sector. Specifically, the combustion of one ton of coal produces between one and three tons of carbon dioxide, dependent upon the carbon content and heating value of the combusted coal. Additionally, coal mine methane (CMM) released through a mine?s ventilation system has a radiative trapping impact approximately 20 times greater than that of an equivalent mass of carbon dioxide. The capture of coalbed methane (CBM) prior to the mining process and its utilization as an alternative energy source provides the possibility of a decreased carbon footprint. Domestically, the past 25 years have seen a significant expansion of the CBM industry. Internationally, in developing countries such as China, the need for western coal degasification technology is growing. A collaborative, international effort will be required to initiate a recognizable decrease in global greenhouse gas emissions. This paper identifies the potential decrease in equivalent carbon dioxide emissions through effective degasification at a hypothetical longwall mine located in China. Advanced, three-dimensional gas reservoir simulation software will be utilized to determine the maximum feasible CBM recovery in a low permeability, high gas content reservoir prior to the mining process.

Jan 1, 2010

By R. P. King

A new device, called the dual impact load cell, has been developed and built at the Comminution Center to measure fracture energy and damage accumulation in brittle particles that are subject to impact. The results show that damage accumulation during impact is not a significant factor in determining the fracture energy or the particle strength. However, predamage induced by thermal pretreatment of the particles has a significant effect on both fracture energy and particle strength.

Jan 1, 1995

By A. E. Petersen

The United States Bureau of Mines conducted research on high-intensity magnetic separation methods for upgrading tantalum concentrates from Alabama. Process flow sheets were studied to maximize tin removal and minimize tantalum loss. Using laboratory-scale equipment, concentrates were produced which contained over 65% combined Ta2O5-Nb2O5. Up to 78% of the tin was recovered as a byproduct, containing about 70% SnO2. Only 1 to 5% of the tantalum reported with the tin byproduct. The producer subsequently incorporated high-intensity magnetic separation into its process flow sheet to provide concentrates for the National Defense Stockpile.

Jan 1, 1993

By J. W. Cooksley

Seismic methods provide an efficient and comprehensive approach to overburden studies pertinent to mining exploration and development, and to other mining and civil engineering problems such as rock mechanics, slope stability, and foundation engineering. For the purpose of defining geologic units and structural features, these methods are generally regarded as the most accurate, but most expensive, of the commonly-used geophysical exploration methods. Although the accuracy and cost of seismic work are generally affected adversely by rugged topography and complicated geologic conditions, it is in rough terrain and complex geology that seismic methods offer important advantages in overburden investigations. For example, to find the surface of rock underlying unconsolidated overburden at depths of approximately 200 feet, a 50-foot spacing of drill holes along the profile line would be required to yield a degree of resolution and accuracy similar to that obtained from a 50-foot spacing between seismic detectors along the same line. See Figure 1. In cases similar to that shown in Figure 1, a twelve-channel recording seismic system would be used. The main components of such a system would be: 1. detectors (commonly referred to as geophones) which convert the ground movement resulting from seismic waves into an electrical signal. 2. a multi-conductor cable which connects the seismic detectors to the amplifiers. 3. ampliiiers, amplify and filter the electrical signals . 4. oscillograph, records the amplified signal. 5. the blaster and firing line. A typical layout of the seismic spread and the components of the system Is shown in Figure 2.

Jan 1, 1968

Microwave pretreatment can improve grindability by weakening brittle particulate material prior to size reduction. The differential thermal expansion experienced by multiphase materials during rapid heating can also promote damage in the grain-boundary region, which may ultimately translate into enhanced liberation. The effect of microwave pretreatment on the breakage characteristics of different ores has been studied using the Ultrafast Load Cell. The energy accumulated during impact (fracture energy) and the particle stiffness have been measured for untreated and microwaved ore samples. It has been observed that microwave pretreatment can weaken brittle multiphase particulate material, as observed by reductions in fracture energy and increase in damage.

Jan 1, 1996

The Mine Safety and Health Administration (MSHA) has conducted studies to evaluate dust control technologies on deep cut continuous mining sections. These surveys have been conducted in different mines using various mining methods, face ventilation systems and dust control systems. The surveys typically consist of respirable dust sampling combined with a time study of mining activities. Measurements of dust control and operational parameters are also made. Critical elements identified for controlling respirable dust in deep cut mining systems include controlling intake dust, dust collector capacity, face ventilation quantities and velocities, positioning of workers, work practices and selection of equipment. This paper discusses how the dust surveys are conducted in deep cut mining sections and how these surveys are used to identify specific dust generating sources.

Jan 1, 1999

By Wayne W. Murdy

Since 1993, Newmont has been actively growing through the development of three major foreign mining operations with a fourth under construction. The first project, Yanacocha in Peru began operating in October 1993 at a time when political and business risk in that country was considered high. In 1995, Newmont began operating the Muruntau Joint Venture in Uzbekistan, the first of its kind in the CIS. In early 1996, Newmont started operating the Minahasa mine in Indonesia. Now, in early 1997, Newmont is undertaking the construction of a $1.9 billion project in Indonesia and is completing a feasibility study with our partner for the development of a gold operation in Mexico. All of these projects have been considered "risky" by most standards, and Newmont has been very successful in all of them through risk mitigation programs including utilizing strong and successful in-country partners, concentrating on developing a strong national workforce with minimal expatriate employees, utilizing World Bank, EBRD and IFC financing and building and maintaining strong ties with host governments. This paper describes in more detail, some of the risk mitigation programs that Newmont has used to successfully grow the company through development of major foreign mining operations.

Jan 1, 1997

By R. W. Draves

Planning and testing in advance of the mining operation are essential. This advance work can involve physical and chemical analysis of overburden cores, field test plots, green- house studies or any of a multitude of other baseline data collection activities. This paper presents the results of Central and South West's field test plots and how they relate to topsoil substitution. Besides the obvious need for testing in advance of mining, there are the inevitable regulatory requirements. Quoting from the office of Surface Mining Regulations concerning topsoil substitution: 216.22(e) TOPSOIL SUBSTITUTE AND SUPPLEMENTS -Selected overburden materials may be substituted for or used as a supplement to topsoil if the office determines that the resulting soil medium is equal to or more suitable for sustaining revegetation than is the available topsoil and the substitute material is the best available to support revegetation.

Jan 1, 1985

By S. A. Pirzada

A thermal plasma assisted laminar flow reactor has been used to evaluate the kinetics of converting alumina to sodium aluminate in flight. Free energy minimization calculations were used to determine experimental conditions. The experimental variables include: alumina particle size, alumina/sodium nitrate molar ratio, temperature and residence time. A mathematical model for the conversion was developed and validated. Experimental and mathematical results are presented.

Jan 1, 1996

By J. Hilgers

Metal prices are often predicted by relying on time trend projections of various economic indicators or even the trend in price itself Thus, time is the underlying explanatory variable acting through at best, a limited selection of economic variables. The price prediction method described in this paper differs from this by analyzing hundreds of economic variables to develop a few principle components that automatically capture the fundamental changes in the economy and delete duplicate or irrelevant information. This leaves a few principle variables to describe a state-space representation of the economy which can then be used for prediction. Forecasts of the price of a metal are then made based on these principle variables.

Jan 1, 1995

The stability of mine roofs in permafrost zones is determined mainly by temperature and ice content. The deformation resulting from creep and temperature dependent physical properties of frozen rockmass is the dominant component of total deformation. Roof bolts can consolidate the roof and control its deformation. In this paper, a finite element model for analysis of the effects of roof bolting in a frozen rockmass is presented. The model includes the variables normally encountered when analyzing the effects of roof bolting in rocks. It also accounts for properties unique to frozen rockmass, creep deformation and the change in Young's modulus with changing temperature. The model shows that, as bolt spacing decreases, there is a trade-off between increased roof stability from increased mechanical support and decreased stability from increased conduction of heat into the frozen roof. This result was expected, and shows that, for a given set of rockmass conditions, including ice content, temperature, particle size, etc., there is an optimum bolt length and bolt density for minimum roof deflection.

Jan 1, 1996

By Morgan M. Sears

The stability of gateroad pillars is crucial in deep-cover longwall mining, especially during transitions to wider panel layouts. This study evaluates the transition from a 700-foot to a 1,000-foot panel layout with an inter-panel barrier in a deep-cover longwall mine in Southwestern Virginia to identify a configuration that enhances stability and reduces operational risks. Using the LaModel program, three pillar configurations were simulated to assess their performance based on stress distributions and pillar safety factors. These included the previously used 4-Entry Yield-Abutment-Yield layout, the current 3-Entry Yield-Abutment layout with a 220-ft inter-panel barrier, and the proposed 3-Entry Yield-Yield layout with a 320-ft inter-panel barrier. The findings of this study suggest that the proposed 3-Entry Yield-Yield pillar layout is more effective in managing stresses in deep-cover mining environments. By optimizing pillar placement and improving load management, this layout could positively impact mineworker safety and health. The study underscores the importance of advanced simulation tools in developing innovative solutions to address the challenges of modern longwall mining operations.

Feb 1, 2025

By M. E. Smith

Chile is the world's largest copper producer and as such sets the standard of practice in copper SX/EW design. The authors summarize the liner systems used at many of Chile's major copper producers both operating and planned. The evolution in the state of the art is also discussed, considering both economic factors and Chile's burgeoning environmentalism.

Jan 1, 1994

By Joseph J. Garbarino

World demand for phosphate fertilizers has grown at an average annual rate of between 6 and 7 per cent over the past 10 years. In the next five years world demand is expected to at least continue to grow at that rate. Also, the continued need for improved fertilizer materials, coupled with improvements in fertilizer technology, have placed added importance on the use of phosphoric acid as a starting material for high analysis phosphate fertilizers. This demand for phosphates and phosphoric acid must be met by increased production. Increased phosphoric acid production also brings increased demand for chemical processing agents including foam control agents. We at Arizona Chemical Company have closely followed the phosphate fertilizer industries needs. Arizona Chemical Company has been an important supplier of flotation agents to the phosphate industry, primarily from its Panama City, Florida plant. We have also recognized the important role played by foam control agents in the wet-phosphoric acid manufacturing process. We feel it is the responsibility of the supplier of foam control agents to offer specifically designed products that are highly efficient and economically useful. The difficulties involved in evaluating foam control agents in the plant are recognized. Owing to the large number of variables present, and the difficulties in controlling these variables during the period of a plant trial, plant evaluation of a large number of foam control agents is impractical. We have attempted to develop a practical, reproducible, and yet rapid, laboratory evaluation test which correlates with plant performance.

Jan 1, 1966