Search Documents

By Robert R. McDougal, Anne E. McCafferty, Bruce D. Smith

Magnetic, electromagnetic, and radiometric airborne survey data have been used in regional and local (drainage basin) scales. In a regional geoenvironmental assessment of the state of Montana, magnetic and radiometric data compiled from airborne surveys were used along with other digital geologic and geochemical data to prioritize mining districts for potential acid water generation. Probability ratio mapping was done in order to integrate the interpretation of many different digital data sets. On a more local scale, the Animas (CO) and Boulder Basin (MT) watersheds have been studied using helicopter geophysical surveys. The airborne geophysical surveys show many more structural features than the geologic maps. Combined interpretation of the geophysical data sets using the probability ratio method has resulted in identification of areas of alteration. Airborne radiometric data in the Boulder Basin area suggests that rocks with high potassium and thorium also have a high acid water buffering capacity.

Jan 1, 2000

By Dae S. Young

The Disjunctive Kriging (DK) procedure was developed to estimate ore recovery figures within a deposit/ domain from limited diamond drill hole (DDH) core assay data taken at the exploration stage. Local recovery figures include minable ore tonnage and ore grades within relatively small areas such as stopes or small panels on a pit bench, for a given cut-off grade. The grade and tonnage should be computed based on the true selective mining units, that is, the average grade distribution of selective mining units within a panel. Local recovery figures are critical information for economic and engineering feasibility studies before mine development, as well as for short-term mine planning for operating mines. This kind of information can be provided only by non-linear geostatistical methods including DK and the Multivariate Gaussian Approach (MG) (Journel, 2, Parker, et al, 5).

Jan 1, 1982

By Scott Jones, Tony R. A. Durkac, David W. Stephens

Williams Mine was considering spending a large amount of capital to install a pumping system underground to rid the mine of slimes; with the introduction of Delvo Stabilizer this challenge would be met. This paper will address the process to introducing the Delvo Technology into the Cemented Roddill Program. Some areas that were worked on included: testing of the mix design, bet dosage rate for an economical solution, temperatures at different levels of the mine, the amount of time needed once the grout was put to sleep, preventing plugs in the delivery system A controlled dosage that gave the Operator a 12 hour window of flowable material was developed and an added feature to the introduction of Delvo was also noted; an increase in MPa strength over the design. Collectively with the help of operators at the batch plant and the underground miners involved with the program all concerns where addressed and all goals met. A cost effective program was implemented thus increasing productivity, preventing costly plugs, and improved the actual maintenance on the entire delivery system, which included the batch tanks, aggitator tanks, all pumps required in the system and of course reducing buildup of slimes at the cones.

Jan 1, 2001

By J. Kemeny, K. Girdner, M. A. Lowery

A strategy for proactive blast planning to improve the postblast fragmentation size has been implemented at the Phelps Dodge Morenci Mine. This strategy was developed in specific phases that include stabilization of blasting practices, systematic changes in blast design and quantification of the size distribution of blasts. Implementing this new strategy would not be possible without an accurate method for quantifying the postblast fragment size distribution. The Split image processing system is now being used to assess fragmentation size using muck pile digital imaging taken on a daily basis and an online fragmentation analysis system installed at the primary crushers. Drilling and blasting variables and fragmentation size are entered into a database, spatially evaluated in a geographic information system and subsequently utilized for mine planning purposes. Using this strategy, significant improvements have been made in postblast fragmentation and continued improvements are expected in the next several years.

Jan 1, 2002

By A. M. Al Taweel, V. K. Kasireddy

Intensive coal cleaning usually necessitates fine grinding of the feed in order to liberate inorganic constituents from the surrounding organic matrix. This however adversely affects the ability of flotation techniques to beneficiate coal. Such difficulties are mainly attributed to the increase of particle population density, the decrease in capture efficiency, and the greater tendency of inorganic components to report with the froth. A three-pronged approach was adopted in an attempt to overcome these difficulties. The aggregative flotation technique was used to reduce particle population densities and improve capture, while unconventional spargers were used to generate a wide range of bubble sizes. Use of unagitated flotation columns allowed for the maintenance of countercurrent flows in both the recovery and washing sections. The combined effect of these parameters enabled the recovery of 92% of the carbon content of coal having an average particle size of 20.5 µ m, while rejecting 85% of the ash. This was accomplished using 2 kg of fuel oil per tonne of coal in a column 2 meters high operating at 2-3 tph/m3, a capacity which compares favourably with conventional cells.

Jan 1, 1989

By R. V. Ramani, W. Miola

The MSHA prescribed method for the determination of quartz in airborne respirable-dust samples from underground coal mines is the P-7 method, a combination of low-temperature, radio-frequency ashing (LTA) and infrared analysis (IR). There is no prescribed procedure for quartz analysis in bulk samples of coal and host rock. Dispersive infrared (IR), Fourier-transform infrared (FTIR) and X-ray diffraction (XRD) methods are most commonly used for the analysis of quartz in powders. Several aspects of the experimental procedures, such as the preparation of the analysis sample from bulk samples, ashing techniques, scanning procedures, peak measurement location, calibration techniques, sample amounts, size consist and data interpretation, affect the results from each of the methods differently. Significant differences in analytical results obtained from X-ray diffraction (XRD) and infrared spectroscopy (IR) on the same samples are reported. All studies point to the need for reliable quartz analysis methods. In a recent research program, a procedure for preparing bulk-coal and host-rock samples for quantitative quartz analysis was developed. Further, the results from X-ray diffractometry and infrared spectroscopy for quartz content on identical samples were compared. Calibrations with pure and mixed standards were used to assess the influence of particle-size distribution, matrix and calibration on the analytical results. In this paper, several issues concerning the measurement of quartz in the samples of coal, host-rock and airborne respirable dust from mines are outlined and quantified.

Jan 1, 1996

By Jean-Michel M. Rendu

According to statistical theory, the geostatistical methods of ore reserves estimation are greatly superior to any other method. However acceptance of geostatistics by the mining industry has been slow and not as wide spread as one would expect. One of the reasons for this cautious approach is that it is often questioned whether the geo- statistical assumptions are satisfied in real world situations. When blocks of ore are estimated in a mineral deposit, geostatistical theory can be used to determine which method of estimation should give the best results. Using this theory, the relationship between estimated value and true block value can be quantified. There is a need to verify that this theoretical relationship is actually observed in practice, and that the block estimates ' obtained using the theoretical ly best method of estimation, are actually most similar to the true block values. In this paper the results expected according to the theory are compared with the results actually obtained. Sample values from a large bedded gold deposit have been used. Blocks of ore have been estimated by a number of methods, including the polygone, inverse power of the distance, kriging, logarithmic kriging and other geostatistical methods. The block estimates have been calculated from samples on a large grid, and compared with the true block values obtained from additional samples on a much smaller grid. The results of this comparison show extremely good agreement between theory and actual results.

Jan 1, 1979

By Jae-Chun Lee, Kang-In Rhee, D. B. Dreisinger, Hyo-Shin Yu, G. A. Kordosky

The development of a process for direct synthesis of very pure ZnO powders from zinc-bearing waste was investigated. The zinc waste which contains 55% zinc was leached with sulfuric acid. After iron removal by hydrolysis from this zinc solution, purification through solvent extraction by the use of D2EHPA as an extractant was carried out. Then, loaded zinc in the organic solution was stripped and precipitated simultaneously using oxalic acid as a precipitant. Synthesized ZnC2O4 precursors by precipitation stripping were calcined to obtain ZnO powders exceeding 99.9% purity. The effects of sulfuric acid concentration, leaching time, and pulp density on the extraction of zinc were studied and optimum conditions for the solvent extraction were obtained through purification of the zinc solution. The size, morphology, and size distribution of synthesized ZnC204 powders were studied in terms of oxalic acid concentration, temperature, surfactant added, precipitation time, etc.

Jan 1, 1993

By Kenneth S. Johnson

Oklahoma is a region of complex geology where a mobile belt of Paleozoic geosynclines and uplifts on the south abuts against the margin of the North American craton to the north. The state contains many classic areas where fundamental concepts of sedimentation, stratigraphy, structural geology, historical geology, mineral investigation, and petroleum exploration have been formulated through the years. In the southern Oklahoma mountain belts, there are exposed a great variety of igneous and sedimentary rock units seen at few other places in the Midcontinent area. Major geologic provinces of Oklahoma (Fig. 1) include: (1) the cratonic and relatively stable northern shelf areas, including the Ozark uplift; (2) the Ouachita geosyncline (now the Ouachita Mountain belt) and associated Arkoma basin in the southeast; and (3) the southern Oklahoma aulacogen (geosyncline), comprising the area of Anadarko, Ardmore, Marietta, and Hollis basins, as well as the Arbuckle and Wichita Mountain uplifts. The three principal fold belts, the Ouachitas, Arbuckles, and Wichitas, all originated from a series of Pennsylvanian orogenies (about 300 million years ago) in the two Paleozoic geosynclines.

Jan 1, 1999

By Robert J. Timko, R. Lincoln Derick

The Bureau of Mines evaluated the integrity of escapeways in a three entry underground coal mine. A center conveyor belt entry (secondary escapeway), was flanked by an intake (primary escapeway) and a return entry. Diesel equipment was used throughout the mine for material and personnel haulage. A carbon monoxide monitoring system, tied to a data recording computer on the surface, was deployed throughout the belt entry and at selected sites in the intake and return entries. Previously, the company had a fire of unknown origin in another mine, which prompted an interest in the performance of their escapeways. An initial, qua1itative evaluation was performed by burning approximately 14 kg of coal at the mouth of the intake entry. The first test was followed by a similar burn at the mouth of the belt entry. These initial trials showed a high quantity of leakage between entries. In several follow-up evaluations, simulated fires, using a tracer gas, were set in the intake and belt entries. Tracer gas concentrations were obtained in all entries at four different underground locations. The results of these tests showed that permanent stoppings could not guarantee isolated, contaminant-free escapeways.

Jan 1, 1989

By A. C. Noble, D. E. Ranta, J. W. Mustard

Skarn deposits present many unique problems in estimating ore reserves, including difficulties arising from the complex character of the mineralization and intricate ore body shapes resulting from structural complexity. Mineralization within skarns occurs in metasomatically altered carbonate horizons produced by magmatic hydrothermal fluids emanating from intrusive stocks. Deposit formation is controlled by both the presence of favorable host rocks and by proximity of these host rocks to a mineralizing intrusion. Ore controls must be defined to account for abrupt changes in grade that occur between miner- alized and unmineralized horizons. Gradational grade changes within the mineralized zones must also be defined in terms of skarn type and included barren rock to assist in reserve estimation. Defining mineralized limits can be further complicated by faulted, rotated, or folded strata affecting the morphology of an ore body. The MacTung copper-tungsten exoskarn deposit, located along the Yukon-Northwest Territories border in Northwestern Canada exhibits a number of unique properties that preclude a simple mathematical approach to ore re- serve estimation. This deposit is used to demonstrate methods for modeling geologic controls and geostatistical properties for a skarn deposit.

Jan 1, 1992

By Rowan Melrose, Naj. I. Aziz, Arvind Misra

Mathematical models have been developed to simulate longwall heading development systems in Australian Longwall Mines. The models developed consider the effect of non concurrent cutting and supporting systems and concurrent cutting and supporting systems. They also consider the impact of operating parameters on each of these systems. Operating parameters that are considered include pillar dimensions, the use of surge cars, bolting time, shuttle car speed and heading advance per cycle. The effect of these parameters is considered with respect to production rates and also panel advance rates.

Jan 1, 1996

By K. Morsy, S. S. Peng

This paper deals with the causes and mechanisms of a massive pillar failure in a room-and-pillar mine. The mine employed a nine-entry panel system using supersection technique under a cover ranging from 91 to 168 m (300 to 550 ft). Chain pillar squeeze and large roof-to-floor convergence were first observed at the belt transfer point on the very inby side of the main entries. It propagated out by quickly, and, within 24 hours, it had covered an area approximately 1,250-m- (4,100 ft-) long by 762-m- (2,500-ft-) wide. The failure was caught and stopped by a solid barrier pillar. Using computer modeling, this study indicates that the massive failure was initiated because of a combination of undersized chain pillars in some panels and weak immediate floor. Also, the study shows that the massive pillar failure expanded to a large area because of the absence of barrier pillars between some panels and between mains and panels. Based on computer modeling, alternative mine plans were proposed to avoid such problems.

Jan 1, 2002

By J. A. Ryder

Compressed air is a relatively inefficient yet very convenient vehicle for transmitting mechanical energy. It is inefficient when compared to, say, hydraulic or electric energy systems since compressor and pneumatic machine efficiencies are quite low (in the range 20-65%) and reticulation losses can be quite high unless adequate pipe diameters are used to minimize friction drops. It is convenient in that capital and maintenance costs of pipes and machines are exceptionally low, the equipment is flexible and lightweight, the technological level is simple, the form of the energy supply is intrinsic- ally safe, and as an additional minor but psychologically important benefit, it provides a ready source of cooling and air supply for emergency use in deep hot mines. It is for these reasons that compressed air is a premier source of energy for many forms of underground equipment, in particular hand or rig-mounted rockdrills, some forms of rock- handling equipment, and a host of minor applications including agitators, small-lift pumps and temporary f am installations. In a typical S. African deep-level gold or platinum mine, compressed air generation accounts for 15% of the total mine electrical energy bill - more than is used for hoisting. In these mines it is not uncommon for over 100 km of underground compressed air piping to be installed, primarily to supply handheld rockdrills.

Jan 1, 1979

By Arthur J. Borst, Joseph P. Gildner

In a recent National survey, Seattle topped the list for having the worst daily traffic congestion. To address this problem, Sound Transit is planning to build 40km (24 miles) of light rail, including ten kilometers (six miles) of twin tunnels with four subway stations 40 m (130 ft.) to 65 m (210 ft.) deep. The overall schedule is very aggressive and Sound Transit is preparing four separate heavy civil construction contracts for simultaneous underground construction. Three of these contracts are being considered for design-build. Final design will start in March2000 and all underground construction must be completed by the end of 2005.

Jan 1, 1999

By R. J. Sweigard, R. V. Ramani

The effects of postmining land use planning are addressed in this paper. These effects may include savings in reclamation costs and increased value of reclaimed land. However, this may result in greater planning costs and possible delays in production. Therefore, an economic analysis was undertaken in an effort to determine the importance of each potential result and to quantify the overall economic impact of postmining land use planning. A discounted cash flow analysis was performed using a surface mine cost model to analyze the sensitivity of selling price to changes in various postmining land use planning parameters. As a result of this analysis, it was determined that the profitability of a project is most sensitive to delays in production, particularly if the delay occurs after major investments have been made. Many methods have been proposed for evaluating postmining land use alternatives (Sweigard and Ramani, 1981). Both quantitative methods, such as benefit-cost analysis (Brock and Brooks, 1968), and nonquantitative methods have been proposed. The application of one specific analytical method is pursued in this paper.

Jan 1, 1988

By Robert A. Wilson

Los primeros pasos básicos para determinar los valores reales y los minerales concernientes, que son la base para las pruebas metalúrgicas, son presentados en este capítulo. A continuatión, eligiendo el proceso o los procesos indicados para el tratamiento de un mineral, son expuestos los temas. Todo esto es seguido por los procedimientos utilizados, el resultado de los cuales indicará la viabilidad para el tratamiento. Estas pruebas de procedimiento han sido desarrolladas, utilizadas y de probada efectividad en laboratorio con evaluaciones relativas al procesamiento de la planta. Los procedimientos especiales y poco comunes se encuentran fuera de la finalidad de este capítulo. La evaluatión de los resultados de las pruebas y su incorporatión dentro del flujograma preliminar y final para el diseno de la planta son temas igualmente expuestos. El valor de un flujograma, con balances de material y agua para el diseño de la planta, es asimismo mostrado.

Jan 1, 1982

By P. C. Kapur

The hierarchical relationship between three broad kinds of grinding models for a spatially homogeneous, linear, time-invariant batch grinding system are first established. Limiting and asymptotic arguments for arriving at approximate but simpler models are employed in all three cases. These parsimonious models -provide alternate and, in some respects, more incisive and convenient tools for the analyses of grinding processes and simulation of comminution circuits. In the discrete-size, discrete- time class of models, a reduced mill matrix is derived, which is seemingly adequate for those grinding circuits whose identification otherwise is difficult because of limitations on the quantity of data and its quality. In discrete-size, continuous-time types of models, parameter lumping has been employed for obtaining a G-H solution which is quite accurate and exceptionally useful for graphical display of data, model verification, and parameter estimation and simulation. In continuous-size, continuous-time models, a similarity transformation is used for solving the integrodifferential equation of grinding. This solution provides a unified framework for a number of apparently diverse empirical grinding phenomena such as self-preserving behavior of ground particle size distributions and energy laws.

Jan 1, 1987

By K. B. C. Brady, B. E. Scheetz, J. E. Cuddeback, T. W. Bergstresser, W. A. Telliard, S. C. Parsons, R. J. Hornberger

Two weathering procedures are being developed by the Acid Drainage Technology Initiative in cooperation with federal agencies(OSM and EPA). Objects are to: (1) standardize existing humidity cell and leaching column procedures; (2) improve test methods by maintaining a carbon dioxide enriched environment needed to optimize carbonate mineral dissolution, and quantifying particle size variables to evaluate reaction kinetics, and (3) provide flexibility in test method implementation consistent with EPA guidelines for Performance-Based Measurement Systems. Preliminary results indicate the CO2enriched leaching environments produce alkalinities that are similar to field observations and greater than the tests run under atmospheric PCO2. Leaching columns produce higher alkalinity than humidity cells.

Jan 1, 2003

By Raj K. Singhal

Three principal activities are involved in planning and developing a surface mine. These are 1) definition of economic and technical feasibility, 2) design, procurement and construction, and 3) mining and reclamation. The last is the only activity which begins in the feasibility study and continues throughout the life of a mine. It is also the activity which depends heavily on use of computers. This paper deals with a method of selecting mining software and dwells on the recent progress, made in this area. Discussed also is the status of computerized equipment management and information systems: a microprocessor based technology applied to dispatch systems, monitoring of equipment health and performance, wireless data transmission to a centralized data processing unit, and mine- wide information and reporting system. Reference has been made to upcoming developments which offer the potential- of transforming the surface mine of the year 2000 into a "manless pit". Canadian achievements in all of these areas have been highlighted at appropriate places in the text.

Jan 1, 1989