Search Documents

By Thomas J. Kingston

A general overview of the taconite crushing process at Minntac is presented The process is controlled from a central control where the control room operator uses closed circuit TV, computer process control and alarms, graphic panels, and radio communication to roving attendants to run the Plant. This paper points out the operating controls and parameters as the plant operator sees and uses them.

Jan 1, 1980

By J. B. Mitchell

Comminution methods for base metal and precious metal ores have had considerable attention from mine operators, equipment suppliers and design engineers for many years and much of their work has been well reported. This interest derives from a healthy concern with the costs of comminution, often the largest single cost factor in ore dressing of hard ores. Many imaginative innovations have resulted. One notices a trend toward autogenous and semi-autogenous methods, combined with a trend toward very large equipment. Unfortunately, there has been less obvious cost incentive to experiment with softer ores. This is unfortunate because the consequences of inappropriate comminution methods can have an important effect on overall economics by influencing down stream processing and salability of final products. This paper concerns some of the factors to be considered in the selection of comminution methods for potash ores, and gives some specific examples to illustrate some of the principles involved.

Jan 1, 1969

By W. A. Zingg

Impervious zones in copper waste heaps create a problem in contacting the rock with leaching solutions. These zones are normally associated with compacted layers .formed on the surface of each lift by dump truck traffic and by disintegration of the rock exposed to atmospheric conditions. These layers are usually only a few feet in depth--but, nevertheless, act as barriers to vertical flow causing the leach solution to perch in the heap, Consequently, much of the rock remains untouched and the leach solution breaks out the side of the heap instead of continuing downward to bedrock. One solution to this problem is breaking the hard pans with explosive charges. However, to use explosives means adopting new explosive materials and methods. To use this process successfully requires finding answers to operating conditions inherent to waste heaps. Foremost among these are: (1) type and size of casing that can be used because of limitations brought about by drilling problems, caving and, corrosive conditions; (2) perforating the casing at required levels; (3) an explosive capable of being pumped; (4) obtaining detonation of the, main charges through, the wail of the casing; (5) an explosive with the ability to propagate through the voids of the rubble and one which is not affected by water, acidic solutions, or back pressure conditions from hydrostatic heads; (6) to heave and rupture the compacted zones without chambering or recompressing the waste material.

Jan 1, 1970

By John R. Hawley

Ontario, one of the richest mining districts in the world, is a natural storehouse for much of the earth's fresh water supply. Covering over 344,000 square miles, the surface of this Canadian Province is dotted with 250,000 fresh water lakes and is laced with uncounted thousands of fresh water rivers and streams. The southern portion of the Province, for the most part, is flat or lazily rolling farmland. This is where most of the people in Ontario live. Although it is not a major mining area, southern Ontario does possess important deposits of salt, oil, gas and gypsum. Most of these deposits are being actively worked. Toronto, the capital city of Ontario, lies deep in the southern region. Here the climate is mild and the winters are short. The total annual precipitation consists of 27 inches of rain and 65 inches of snow. Most of the major mining companies that do business in Canada have made Toronto their Canadian headquarters. There are two reasons for this. The first, of course, is money. Toronto is the gathering place of many well- known financial institutions. The second is access. Toronto lies within a few hundred miles of some of the most spectacular mining enterprises that exist in the world.

Jan 1, 1973

By Michael Davis

In the fairly recent past, with a history of cheap and abundant energy, it has been possible to predict with reasonable confidence that world energy demand would continue to double about every 15 years. Those who attempted to forecast the role of nuclear energy in future electricity generation could also start with the fairly safe assumption that electricity demand would increase even faster : with a doubling in demand about every 10 years. To estimate the likely future world demand for uranium it was then necessary to introduce a number of other assumptions including the rate of penetration of nuclear energy, the timing and the specific fuel requirements. This series of assumptions naturally compounded the uncertainty, but, remarkably, usually led to future uranium demands being overestimated. Such a bias which has almost always been observed in predictions made over the past 20 years has increasingly made uranium producers sceptical when expected to match the forecast demand with increased production capacity and supporting reserves. This scepticism has, of course, been reinforced by the persistence so far of a buyers' market in uranium throughout the entire period of emergence of commercial nuclear electricity generation.

Jan 1, 1974

By John Hughes

Fundamental to the use of rotary bit drilling equipment for oil and gas drilling is the requirement to maintain a cooling and lubricating environment for the bit and a means of conveying the cuttings from the drilling operation to the surface. The vast majority of such functions are provided for by the use of water based drilling fluids, commonly known as the drilling mud. One of the basic constituents of drilling mud is bentonite, a montmorillonite clay. Bentonite, when mixed with water at approximately 6% solids, will produce a fluid which has several important features in connection with its role as a drilling mud:

Jan 1, 1983

By William N. Poundstone

Since World War II, when off-track mining became popular, mining machinery has undergone much change. However, the change has been basically to make the machines more powerful, more productive and more reliable. Little change has been made, in this period, in the basic mining system. While steady improvement was made in productivity until the passage of the new Federal Coal Mine Health & Safety Act, I believe that the cost Co benefit ratio of further improvement from this basic approach of improving the existing extractive tool is not as promising as I believe may be obtained from a new approach. Consequently, six years ago Conoco and Consol undertook a comprehensive long-range R&D program to see if improvements of a more basic nature could be made in underground mining. We concluded early in our program that while many things currently limit the rate of production such as the rate at which roof can be supported, time needed to advance ventilation systems, time required to clean up and rock dust, time required to maintain and service equipment as well as time lost due to haulage deficiencies, that the key to improvement was a truly flexible continuous high capacity haulage. With face equipment in use today, mining rates can be increased with such a haulage system where the ability to support the roof exceeds the ability of conventional haulage equipment to remove the coal. More importantly, if we could develop such a system, it would set the stage for development of far more sophisticated methods of mining at the face than exist today, and as new and more dependable mining machines and methods are developed, continuous transportation will enable the gains envisaged in production to be realized.

Jan 1, 1974

By Takahide Wakamatsu

In Japan all the complex sulfide ore deposits of base metals have been developed as underground mining. The underground mining cost is extremely high as compared with open pit mining case. Therefore, in milling section of base metal mines, technical advance for maximum recoveries of valuable constitutents in ore has been required all the time to utilize as much ore mined as possible. At present, in mill plants treating "Kuroko", complex sulfide ore, concentrates of copper, lead, zinc, pyrite and barite are produced, with gold and silver contents in the copper, lead, and zinc concentrates being estimated as extra profit. As in the case of Kuroko milling plants, gold and silver contents in the lead and zinc concentrates of lead-zinc ore milling plants are also varuable from an economical viewpoint. Silver content is very high in Kuroko crude ore as well as lead-zinc ore.

Jan 1, 1982

By J. Gordon Scott

The Iron Ore Company of Canada has now been operating a computer for the grading or blending of direct shipping ores for two years. This paper deals with the computer application pertaining to the grading of direct shipping ore. It consists of five sections. The first part deals briefly with a description of the operation of the Iron Ore Company of Canada; the second with the source and flow of the various data required to grade or blend ore; the third briefly outlines the computer programs used in this application; the fourth illustrates the mathematical approach used to properly blend ore. The final section briefly describes other technical computer programs.

Jan 1, 1964

By D. L. Kiser

Conventional and advanced coal preparation technologies were investigated through both a literature search and through direct contact with investigators and developers. In addition to a brief description of each process, performance characteristics including feedstock type, ash and sulfur reduction, thermal energy recovery and cost are provided in a tabular form. Seven of the most commonly utilized conventional coal preparation processes, including those respectively accepting coarse, intermediate and fine coal feed, were reviewed. It was found that certain properly implemented and well maintained conventional processes were capable of better than 75 percent ash removal while recovering 90 percent or more of the inherent thermal energy. Almost 50 advanced coal preparation processes were investigated based on biological, chemical and physical principles. Physical processes investigated included cycloning, homogeneous heavy media, electrostatic, high gradient magnetic, flotation and selective coalescence. Using pulverized coal as a feedstock, some of these processes are respectively reported to be capable of removing better than 95 percent ash. 95 percent pyritic sulfur, and 50 percent organic sulfur while incurring energy losses of less than 5 percent.

Jan 1, 1986

By Milton Hood

The Copper Flat Property is located approximately 6 miles NE of the small town of Hillsboro in Sierra County, N. M. (Fig. 1). Hillsboro was the center of considerable mining activity in the late 1800's and early 1900's following the discover, of gold bearing vein deposits and later discovery of, placer gold along the east slopes of the Animas Hills. The Copper Flat orebody is a porphyry type deposit occurring in a small quartz monzonite porphyry stock that has intruded the center of a circular andesite plug (Fig. 2). The primary ore mineral is chalcopyrite. By-product values are contained in gold, silver and molybdenum.

Jan 1, 1983

By D. Loy LeRoy

As we are all aware, the impacts of the 1977 Surface Mining Act and the implementing OSM Regulations require application of new, as well as existing, equipment and technologies. Our firm recently completed (June, 1979) a study for the Department of Energy titled "Analysis of the Impact of Public Law 95-87 on Mining Performance." The objective of the study was to analyze the impact of the Act and its regulations on mining performance in order to provide recommendations to alleviate the impacts identified, including identification of research needs. This paper presents some of the highlights of that report: projected cost increases; additional equipment needed for compliance; review of methods currently practiced or those which can be modified; and will focus particulary on equipment and technology applications.

Jan 1, 1980

By J. Van Kleunen

In the Spring of 1959 the Riverside Cement Company, a Division of American Cement Corporation, placed into operation at their Oro Grande California plant a new crushing-blending-reclaiming facility. This new facility, in conjunction with other modernization in the plant, has established a degree of automation and reliability on a-plant-wide basis which heretofore had not been attained in the industry. The blending and reclaiming facilities for raw stone and cement clinker at this plant represent not only the first computer programmed materials handling system of its type in the industry, but also the first installation of specialized equipment which was designed for high capacity, fully automated operations.

Jan 1, 1963

By Albert H. Fay

The gypsum industry makes significant contribution to the wealth of our nation. This non-metallic mineral ranks in the highest order with America's most precious resources. Evidence of this is borne out by the fact that gypsum is a vitally necessary element in the building, industrial and agricultural industries. In 1967, the United States consumed 14 million tons of this valuable ore. Of .this amount 69% was required by the building industry for the manufacture of building materials. An additional 21% was directed to the industrial market, for the manufacture of Portland Cement and for other industrial uses. The remaining 10% was used for agricultural purposes.

Jan 1, 1969

By George C. Carter

It was just a little over three years ago that the "Go" button was pushed to start operations on the blending piles at Oro Grande. As is usual with any new installation, there were problems that had to be solved. This paper will concern itself with those problems directly related to quality control. To obtain a consistent outgoing quality level at the most economical level for a finished product requires two main points: 1. Measurement of variations in the process, 2. A method of making a predictable change to adjust for variations. The manufacture of cement requires a relatively high degree of accuracy if a consistent outgoing quality level is to be maintained. The blending piles were our solution to this problem.

Jan 1, 1962

By M. E. Lewellyn

A new class of thionocarbamates, O-alkyl-N-allyl thionocarbamate (III), has been found to give better metallurgy than 0-isopropyl-N-ethyl thionocarbamate (I) for a number of sulfide ores containing copper, lead, and zinc. Data on the results of flotation tests with several such ores are presented. The improved metallurgy is believed to be due to the participation of the allyl double bond in the complex formation of the thionocarbamate on the surface of the mineral.

Jan 1, 1985

By T. D. Oulton

The only known attapulgite clay deposits of any considerable extent and purity in the United States are roughly bisected by the Georgia. Florida state line between Decatur County, southwest Georgia, and Gadsden County, northwest Florida. Although attapulgite clay occurrences both farther East and South are known and have been mined to some extent in the past, at the present time it can be said that substantially: all of the commercial attapulgite clay mining and pro¬cessing is concentrated in a roughly rectangular area some 25 miles long by 15 miles wide,, in the general region of Attapulgus, Georgia, and of Quincy and Havana, Florida. Within this area are located the clay processing plants of the four major producers as well as most, if not all, of the currently active mining operations. The approximate location of the plants and of some of the open mines are shown in the local area map, Figure No. 1, for the purpose of orientation only.

Jan 1, 1965

By A. E. Hunt

Over the past twenty-live years since large scale truck haulage in open-pit mining began, the periodic introduction of Larger capacity vehicles has provided increased productivity and reduced costs. WISEDA Ltd. has introduced a 220 ton capacity, two-axle rear dump, diesel-electric truck for the world-wide large open-pit mining industry. Design features and components selected in the development of this vehicle will be presented along with operating experience and a brief history of rear dump truck evolution.

Jan 1, 1983

By R. E. Mason

Shotcrete has been used for approximately 20 years to facilitate tunnel excavation through poor ground. Early examples of such usage in North America include the recuperation of the Granduc Mines access tunnel in Northern British Columbia, and similar work performed in the Carley V. Porter and Big Walker Tunnels in the United States. Mining companies such as Craigmont Mines in B.C. and Hecla Mines have used shotcrete in their workings for the past ten years. Shotcrete is now a widely utilized fool in the mining and tunnel construction industries in North America, but the accumulated experience is too limited for many to fully appreciate the capability of shotcrete to control ground movements and to understand the limitations of this tool. It is common, for instance, to use shotcrete to "bridge the gap" between rock bolt-supported and steel-rib supported ground and to avoid the use of shotcrete in water-bearing ground. Shotcrete can, and has been, used economically and practically under most severe ground conditions.

Jan 1, 1976

By W. B. Weston

To mining people who have experienced the tremendous expansion of existing operations and the development of new properties over the last several years we do not have to point out the difficulties in hiring skilled equipment operators. To those of you who have opened operations in some of the more remote places in the world this is not just a difficulty. It is an impossibility. Your only recourse has been to try and train whatever manpower has been available. Depending upon your success in training, the next problem has been to keep them. On todays modern equipment, the skill of the operator remains as the greatest single variable affecting the performance of the machine. On a blast hole drill, for example, a skilled operator will get good production footage, acceptable bit life and minimal machine downtime The unskilled operator will not only fail to get the acceptable production footage but all too frequently this failure is coupled with low bit life, high repair costs and excessive machine downtime. Even between experienced operators, on identical machines, in the same kind of material we find significant variations in performance. It is, therefore, the skill of the operator, not just his experience, which makes the difference. The problem, as presented to us by our customers, has been to find a way for the unskilled man, with minimal training, to match the performance of the most skilled and experienced operator. The obvious answer is automation.

Jan 1, 1970