Search Documents

By R. K. Zipf

Recent scientific studies by researchers at the National Institute for Occupational Safety and Health (NIOSH) and the U.S. Army Corps of Engineers (USACE) presented the worst-case explosion pressures that can develop if a methane-air mixture of a certain composition and dimension accumulates and ignites within a sealed area of a mine. The Mine Safety and Health Administration (MSHA) issued its final rule on sealing of abandoned areas which considers potential explosion pressures and the risk of achieving the necessary conditions. The new MSHA seals regulation has increased the pressure design criteria an order of magnitude beyond the old standard of 140 kPa (20 psi) to 800 kPa (120 psi). However, there still are major knowledge gaps pertaining to seals and sealed areas including: (1) the composition of the sealed area atmosphere and how it changes in time and space, (2) explosion pressures that might actually develop within sealed areas, (3) engineering procedures to follow when designing seals and seal installations, and (4) guidelines to manage the atmosphere within sealed areas with monitoring or inertization. NIOSH has initiated a seals research program with collaborators from Safety in Mines Testing and Research Station (SIMTARS) in Australia, West Virginia University (WVU), the Naval Research Laboratory (NRL), and USACE. Highlights of progress so far include: (1) construction of a gas explosion tube at Lake Lynn Laboratory for studying large methane-air explosions, (2) computer simulation of the fluid dynamics of high pressure methane-air explosions, (3) development of seal analysis methods considering construction materials, reinforcement and the seal foundation, and (4) development and testing of innovative seal designs that utilize inexpensive, readily-available rock rubble to resist high explosion pressures. NIOSH researchers aim to provide sound engineering guidelines to better address the new MSHA seal regulations. DISCLAIMER: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By R. A. Speirer, T. C. Bettinger, L. P. Richardson

INTRODUCTION The Bureau of Mines (The Bureau) remote sensing researchers at the Denver (CO) Research Center, have been investigating computerized methods to detect and map surface linear features called "lineaments" for ground hazard assessment in mines. Many of these lineaments at the test mine site were found to correlate to subsurface geologic discontinuities such as faults, fractures, and joints that intersect coal seams at depth. These features adverse1 y affect the roof and rib integrity in underground mines, thus contributing to rock failures that may result in injuries to mine workers and loss of production. Advance knowledge of the existence of such hazardous geologic features can aid in mine planning and development. Lineaments may be observed in a variety of images of the earth's surface. Linear features that can be observed using Landsat mu1ti spectral scanner data (MSS) images range from regional (greater than 3 miles in length) to an intermediate length of from 1 to 3 miles. These images are recorded in discrete radiation bands in the green, red, and near-infrared portions of the el ectromaynetic spectrum. These data are acquired from the EROS Data Center of the U.S Geological Survey, Sioux Falls, SD, in digital format on magnetic tapes that are suitable for processing on certain minicomputers. Shorter lineaments length (less than 1 mile) can be observed in high- to low-a1titude aerial photography, radar, and infrared images with image scale ratios of 1:1,000,000 or less. These linear features can correlate to smaller dimensioned faults, and to fracture and joint sets at the local geologic scale. Other informational sources can help substantiate 1ineament analyses, such as well logs, mine naps, topographic data, and geophysical data acquired over the study site. These data must be in a digital format to process on the "DEC PDP 11/23 minicomputer system1". Data can be acquired in

Jan 1, 1986

By J. E. Powell

Introduction The disposal of mine tailings, development rock, and other unwanted refuse material underground in mines by using pneumatic conveying techniques has been undertaken in the coal industry for many years. Similar equipment has been utilized for backfilling hard rock mines and is currently being applied in a gold mine in South Africa where development rock is being stowed in the mined-out stopes to help reduce the incidence of rock outbursts. On a limited scale, pneumatic conveying has been applied for backfilling uranium mines and one particular mine in New Mexico, U.S.A., has used this technique for 8 years. Other uranium mines in this area are now considerinq the dry backfill technique to eliminate the problems associated with hydraulic fill. The need to backfill in uranium mines is primarily of importance to improve ventilation, stabilize the pillars and roof, and possibly to extract a larger percentage of the uranium ore. If this can be achieved by utilizing the tailings from the beneficiation plant and using rock from the development headings which in itself may be slightly radioactive, then a greater benefit can be derived. Backfill can be achieved with hydraulic fill methods by running slurry into the stopes and allowing the water to decant and return through the footwall development entries to sumps for pumping to the surface. However there are several disadvantages associated with this method in that water is percolating throough the mine workings; it is necessary to build bulk heads in flat lying deposits; it is difficult to fill right to the back; and the decanted water takes with it quantities of the finer sand particles which results in maintenance problems with the mine pumps. Pneumatic conveying can overcome these problems in that the voids can be completely filled with high degree of compaction, heavy bulk heads are not necessary, the development rock can be added to the pneumatic system for disposal underground so eliminating hoisting cost to the surface, and cement can be added to the wetted material. To

Jan 1, 1980

By Z. Sample

"INTRODUCTION This past year commodity prices continued their dip with increased volatility causing market values to slide another 16% putting increased pressure on even the largest companies to improve their free cash flow.[1] Without a recovery in commodity prices in sight, companies must find a sustainable method to improve returns in the current economic climate. In an effort to improve plant sustainability, the mineral processing industry is investing in advanced automation technologies and innovative processing methods that are both more reliable and more efficient than ever before. One such breakthrough technology is Heap Leaching (HL). This method of extraction has certain advantages over traditional metallurgical methods making previously unsustainable operations economically feasible. While HL is already seeing use in the gold and copper industries among others, recent developments may allow for the use of HL to process primary sulfide ores which make up about 80% of today’s ores.[2] For this reason, this emerging technology is poised for exciting growth. Unfortunately, as with any process change, the implementation of HL projects requires significant training on both the control system as well as the underlying process, and further, due to the complex nature of the HL process, this can be a particularly difficult task. DEMOGRAPHIC TIME BOMB Even before the implementation of these new technologies, the availability of the skilled workforce has already become a significant problem for the mining and mineral processing industries. From a survey of 912 mining professionals, Stratum International found that a mere 0.4% of senior level candidates were between the ages of 25 and 34 and a similar proportion aged over 75 years.[3] This indicates that there is both a deficiency of young skilled workers and a skilled workforce that is retiring earlier than the previous generation. Combined with data published by the US Department of Labor stating that the median age of the mining workforce is approaching 50 years old, research suggests that up to 50% of skilled mining and mineral process professionals are expected to retire in the next 5 years, leaving with their irreplaceable knowledge and experience.[4] While it is projected that the labor pool will be sufficient to fill open positions, the real question is if this young workforce will have necessary skill sets and experiences. In addition to a rapidly aging workforce and an inexperienced labor pool, a study done by the Oil and Gas Journal showed that it takes about 7 years, on average, for new workers to achieve a level of competency that permits them to assess risks and appropriately make decisions.[5] Not only is this figure is in direct conflict with the typical tenure of 5 years in one position meaning that the thinly spread skilled labor will be required to become senior staff before they are able to achieve competency in their current role, this also means that these millennials are not given the opportunity to become competent in their role before the retirement of the more experienced workforce."

Jan 1, 2016

By M. C. Williams

The solution of the dynamic population balance model (PBM) of a closed grinding network consisting of a mill, sump, and cyclone is problematic. The fact that the dynamic PBM model equation solution to the Inverse Problem for grinding systems is degenerate or underspecified is demonstrated. Two numerical solution approaches to the Inverse Problem are used. These are: 1) providing additional constraints on breakage selection functions or 2) performing the Arbiter-Bhrany (or other) normalization of the selection functions. Actual experimental anthracite batch grinding data is used to demonstrate the non-unique functionality of the batch dynamic mill selection and breakage functions for a real physical system. The Levenberg-Marquardt algorithm for systems of constrained non-linear equations is used to solve the batch dynamic PBM grinding equations to obtain the grinding selection and breakage rate functions. Different solutions to the same PBM transport equations are provided. The mill, sump and hydrocyclone were modeled as a CSTR operating at various retention times. Batch dynamic PBM data was used to provide the mill kinetic and breakage selection function data. Two different solutions were obtained depending on the numerical solution approach. The severity of the non-uniqueness problem for dynamic grinding is demonstrated. Each solution approach to a dynamic PBM with transport, while giving the same prediction for a single batch grinding time, gives different solutions or predictions for mill composition for other grinding times. This fact makes dynamic nodal analysis and control problematic. The fact that the constraint solution approach gives a solution may suggest that normalization for closed networks is not necessary. Differences in solutions to the PBM cannot be excused away by inaccuracies in the data used to model the grinding phenomenon.

Jan 1, 1995

By S. K. Kawatra

The fly ash from coal combustion often has a high unburned-carbon content. This can make it unusable as a cement admixture, which is the major fly ash utilization market. As a result, high-carbon fly ashes currently disposed of by landfilling, at sometimes considerable expense. In this paper, the use of froth flotation to remove the unburned carbon from fly ash is described. Three different fly ashes were studied, which had Loss-on-Ignition (LOI) values of 6.79, 6.90, and 11.11 %. It was found that the use of an alkanolamide/oil mixture as a froth-conditioning reagent could greatly reduce the amount of collector needed, by increasing the affinity of the collector for oxidized carbonaceous surfaces. For each of the three fly ashes, froth flotation reduced the LOI of the ash to less than 2% which is well below the ASTM specification of no ' more than 6.0% LOI for Class F fly ash. Increasing carbon content of the ash tended to increase the quantities of reagents needed in flotation.

Jan 1, 1996

By Donald T. Mylar

It is axiomatic that in designing a bulk material handling system the primary consideration is the functioning of the machines. The structure is secondary -its reasons for being are to support, enclose and provide access to the machine, for servicing. This results in a wide variety of supporting structures. Other considerations are: plant layout, local soil conditions, climate, local laws and codes, and last, but by no means least, the Customer's wishes.

Jan 1, 1971

By D. L. Stevens

Following an in-depth scenario and strategic-planning exercise in 1997, Noranda's mine production goal was set at 500 kt/a (550,000 stpy) of both copper and zinc metal in five years. There had been no recent discoveries, reserves were shrinking and things had to be done differently and quickly. Change is now continual in Noranda's program. The following steps were taken: the exploration and business development groups were combined, teams were formed to search for and respond to opportunity; geologists were coached to become more business minded and engineers were coached to become more optimistic; the company went global; clear thresholds were set, marginal properties were farmed out and other properties were fast tracked; reconnaissance exploration was focussed where there was a clear competitive advantage; and Noranda became a "flexible" partner to juniors and seniors. Is it working? A number of successes, near successes and outright failures are discussed. The main result is a much higher rate of opportunity flux, which is essential for success in the mining industry.

Jan 1, 2000

By Barnaby J. Watten, Sibrell. Philip L., Brian J. Vinci, Andrew E. Friedrich

We evaluated a new process for remediation of acid rock drainage (ARD). The process treats ARD with intermittently fluidized beds of granular limestone maintained within a continuous flow reactor pressurized with CO2. Tests were performed over a thirty day period at the Toby Creek mine drainage treatment plant, Elk County, Pennsylvania in cooperation with the Pennsylvania Department of Environmental Protection. Equipment performance was established at operating pressures of 0,34,82, and 117 kPa using an ARD flow of 227 L/min. The ARD had the following characteristics: pH, 3.1; temperature, 10 OC; dissolved oxygen, 6.4 mg/L; acidity, 260 mg/5; total iron, 21 mg/L; aluminum, 22 mg/L; manganese, 7.5 mg/L; and conductivity, 1400 uS/cm. In all cases tested, processed ARD was net alkaline with mean pH and alkalinities of 6.7 and 59 mg/L at a CO2 pressure of 0 kPa, 6.6 and 158 mg/L at 34 kPa, 7.4 and 240 mg/L at 82 kPa, and 7.4 and 290 mg/L at 117 kPa Processed ARD alkalinities were correlated to the settled bed depth (p<0.001) and CO2 pressure (p<0.001). Iron, aluminum, and manganese removal efficiencies of 96%, 99%, and 5%, respectively, were achieved with filtration following treatment. No indications of metal hydroxide precipitation or armoring of the limestone were observed. The surplus alkalinity established at 82 kPa was successful in treating an equivalent of 1136 L/min (fivefold dilution) of the combined three ARD streams entering the Toby Creek Plant. This side-stream capability provides savings in treatment unit scale as well as flexibility in treatment effect. The capability of the system to handle higher influent acidity was tested by elevating the acidity to 5000 mg/L with sulfuric acid. Net alkaline effluent was produced, indicating applicability of the process to highly acidic ARD.

Jan 1, 2000

By R. J. Matetic

The impact of longwall mining on the local hydrological regime has become an important environmental focal point. Unfortunately, only a few studies have addressed the timing and range of well fluid level fluctuations and the associated ground movement. Furthermore, even fewer studies have determined the influence of longwall mining on water quality. The U.S. Bureau of Mines is providing insight into this environmental concern through a program of field case studies. One such study was conducted in Cambria County, PA where five observation water wells were drilled above two adjacent longwall panels. In this study, three wells were completed as nested piezometers and the remaining two served as producing wells. The piezometers were positioned along a line oriented subparallel to the longwall face and were located at the centerline of each panel and over the intervening chain pillars. The piezometers were designed to monitor fluid level fluctuations in both shallow and deep water-bearing zones. Slug tests were conducted before and after mining to characterize changes in hydraulic conductivity of the respective water-bearing zones. Pressure transducers and data loggers were installed to provide continuous fluid level fluctuation data as mining developed through the study area. The producing wells were drilled to provide water quality information. One well was located directly above the centerline of a panel and the other was positioned over the panel&apos;s set-up rooms. The wells were designed to simulate domestic use and were produced daily, for four hour intervals, throughout the study. Samples of the produced water were collected before and after mining progressed through the area. In addition, an array of monuments was installed near the study wells and was periodically surveyed to characterize mining-induced surface deformations. This study shows that: a) the observed changes in ground water chemistry did not affect the potability of the water; b) short-term major water level fluctuations occur at the approximate time of undermining; and c) water level recovery begins before the process of subsidence is complete.

Jan 1, 1986

By John W. Tieman

The increasing magnitude of our nation&apos;s pollution problems seems to stem from two main factors: urbanization and technical advance. In 1920, less than half the country&apos;s 106 million people lived in cities. Forty years later, the urban population accounted for 70 percent of the nation&apos;s 179 million. It is predicted that by the end of the century, 95 percent of the U. S. population, estimated at 280 million, will live in urban areas. As these people live increasingly in city concentrations, their residues also concentrate. With technological advances to support the increasing population, the variety and quantity of goods that we use also increases. New materials and processes result in increases in pollutants, some of them new. The harmfulness of these pollutants is sometimes known, but sometimes only suspected. One pollutant of concern at the present time is sulfur dioxide, the product of combustion of sulfur-containing fuels. Research on processes to remove sulfur oxides from flue gas has been in progress for many years. Pioneers in this field were the British who, in the early 1930&apos;s, installed a full-scale flue gas scrubbing unit on a 120 MW boiler using alkaline water from a Thames estuary plus chalk. Since that time, various methods have been studied by many investigators. Federal laws covering air pollution started with the 1955 Air Pollution Control Act. With the advent of the Air Quality Act of 1967, and subsequent publishing of criteria and available technology for control of sulfur oxides in January 1969, the clamor for information on commercially available control techniques to remove sulfur from fossil fuels has rapidly increased. Although many state-of-the-art papers have deluged the literature during the past several years, the research going on in the area of sulfur oxides control is of such importance that periodic reviews are justified. It is the purpose of this paper, therefore, to again review the state-of-the-art, but this time from the stand-point of what is immediately commercially available

Jan 1, 1972

By Laura J. Carroll, Gordon A. Goldsmith

Experts, like many of the speakers at the SME Annual Conference, are frequently called upon by lawyers to assist them in litigation. Due to the technical nature of many cases, the testimony of an expert with knowledge and experience in a particular field is necessary to help a judge or jury understand and decide certain issues. Environmental litigation is no exception. Experts routinely are called upon to offer testimony to establish the existence of contamination and its source, as well as the potential health and environmental risks associated with the contaminants. This article will briefly discuss the factors courts apply to determine whether to admit expert testimony after the recent Supreme Court decision in Daubert v. Memell Dow Pharm., Inc., 509 U.S. 579 (1993). The Court&apos;s decision in Daubert overruled a long-standing test that had based the admissibility of scientific evidence on its "general acceptance" in the field in issue. Next, the article will discuss in general terms what a party must do to "link a particular defendant&apos;s conduct to the contamination involved in order to recover from that defendant. This link, known as causation, varies depending upon the type of claim being asserted. Expert witnesses are used extensively to help establish causation. JUNK SCIENCE OR GOOD SCIENCE- HOW DOES A COURT DETERMINE WHAT TO LET IN A frequent complaint in litigation involving technical or scientific issues is that one party or another is trying to use so-called "junk science" to prove its case. While some expert testimony might be so clearly lacking in support or so "off the wall" that a court can easily determine to exclude it, other testimony, especially testimony on the "cutting edge," is much more problematic. In 1923, the District of Columbia Circuit Court of Appeals decided the case of Frye v. United States, 293 E 1013 (1923). In deciding whether to admit certain expert testimony, the court in Frye stated that while a court will "go a long way in admitting expert testimony deduced from a well-recognized scientific

Jan 1, 1998

By David A. Grisafe

Divided opinions concerning dredging-permit locations and boating uses on the Kansas River in northeastern Kansas led to a study of the recreation potential on the river by a legislatively mandated interagency group (five agencies) that included the Kansas Geological Survey (KGS). In addition, the KGS conducted its own study of the river corridor, encompassing the development, geology, and economic resources of the corridor (Brady and others, 1998). The corridor area is 12 mi wide and 140 mi long (171 river miles). Included in the study was the potential impact of restric¬tions to river dredging. The Kansas River and its floodplain in northeastern Kansas are underlain by Lower Permian and Upper Pennsylvanian limestones and shales. The river and its floodplain are the major sources of sand and gravel for northeastern Kansas, and the limestones along the river bluffs supply crushed stone and building stone. The population of the 10-county area bordering the river has grown by 20% since 1980, and now comprises nearly 40% of the state&apos;s population (U.S. Bureau of the Census, 1996). Projections (Floerchinger, 1992) indicate close to 50% of the Kansas population will reside in these counties by 2025, with a continued increase in the demand for aggregates. Factors such as floodplain width, price and availability of land, and overburden ratios tend to favor river dredging on the lower part of the river, and floodplain or pit dredging on the upper portion. The use of alternate sources of sand and gravel such as the Missouri and Arkansas Rivers would increase sand prices due to transportation costs to much of the 10-county area. In 1996, river and pit dredges along the Kansas River supplied more than 3 million tons of sand and gravel valued at about $8 million to northeastern Kansas. As a result of its study, the KGS had concerns with the idea of large recreation zones on the river that excluded river dredging in areas of presently large population and projected population growth. This controversial issue is likely to recur elsewhere.

Jan 1, 1999

By Jianmin Qin, Raja V. Ramani, Wilson Miola

The number of underground work entities operating under reduced dust standards in U.S. coal mines has been increasing since the start of the decade of the 80s and is currently approaching 10,000. The concern for controlling the quartz levels in airborne respirable dust in coal mine has manifested itself in several improvements in equipment selection and operation, face ventilation practices, and dust control procedures. At the same time, fundamental studies have been initiated on determining the source-sink relationships of the airborne quartz dust. The P-7 method is the prescribed method for the determination of quartz in the respirable airborne dust samples from coal mines. Questions have been raised on the reliability of the P-7 infrared spectrometry method for quartz analysis in powders. No specific method has been defined for quartz determination in bulk samples from the mine. In a recent study on the relationship between quartz in the airborne dust and that in the materials being mined, both infrared (IR) and x-ray diffraction (XRD) methods were used on a suite of samples from several coal mines. These samples encompassed airborne respirable dust samples, airborne total dust samples, the oversize fraction from the respirable samplers, ROM samples, channel samples, and chip samples from the face, roof, and floor materials. In this paper, the sample preparation and analysis procedures for the samples are discussed. The data, analysis results, and comparisons of the P-7 and XRD results are presented. The quartz percent determined for the same sample by the two methods are different. In 85% of the samples analyzed, the quartz percents determined by the XRD method are higher than those obtained by the P-7 method. However, there is a strong linear relationship between the results from the two methods. Further, the XRD method indicates an average of 20 percent more quartz than that from the P-7 method. The reasons for the differences in the results and the need for additional studies are explored.

Jan 1, 1991

By Chee S. Theng

As the 2016 president of the Society for Mining, Metallurgy & Exploration Inc., I am pleased to present the 2016 issue of the Transactions of the Society for Mining, Metallurgy & Exploration Inc., Vol. 340. A significant portion of the contribution that we make as a professional society is the publication of professional and technical papers that accelerate the advancement of scientific knowledge and enable the transfer of technology. Communication within the mining community is the key to a successful society. This technology exchange continues a tradition that dates back to the 1871 meeting of 22 mining engineers in Wilkes-Barre, PA, that resulted in the founding of the American Institute of Mining, Metallurgical and Petroleum Engineers (AIME). Those individuals envisioned that these transaction volumes “would form a most valuable and greatly needed addition to our professional literature.” This volume fulfills that pledge. The 2016 Transactions contains some of the most interesting research and insights from the past year and features an international slate of authors spanning industry, academia and government. Papers include the latest findings from the U.S. National Institute for Occupational Safety and Health (NIOSH) and special-issue articles on process development testing. The 2016 Transactions consists of a total of 65 technical papers, encompassing all 21 papers published in 2016 in the Technical Papers Section of Mining Engineering (Vol. 68) and all 27 papers published in 2016 in Minerals & Metallurgical Processing (Vol. 33). Additionally, this volume contains 17 papers that are being published for the first time in this issue. The papers presented in this volume were written by some of the most distinguished professionals in the industry worldwide. All of the technical papers were peer-reviewed. The process of review and publication requires much hard work by authors, reviewers and our publications staff. As the 2016 president of SME and on behalf of all our members, I would like to extend our gratitude to all whose volunteer efforts contributed to the publication of this volume.

Jan 1, 2016

By Chee S. Theng

As the 2017 president of the Society for Mining, Metallurgy & Exploration Inc., I am pleased to present the 2017 issue of the Transactions of the Society for Mining, Metallurgy & Exploration Inc., Vol. 342. A significant portion of the contribution that we make as a professional society is the publication of professional and technical papers that accelerate the advancement of scientific knowledge and enable the transfer of technology. Communication within the mining community is the key to a successful society. This technology exchange continues a tradition that dates back to the 1871 meeting of 22 mining engineers in Wilkes-Barre, PA, that resulted in the founding of the American Institute of Mining, Metallurgical and Petroleum Engineers (AIME). Those individuals envisioned that these transaction volumes “would form a most valuable and greatly needed addition to our professional literature.” This volume fulfills that pledge. The 2017 Transactions contains some of the most interesting research and insights from the past year and features an international slate of authors spanning industry, academia and government. Papers include the latest findings from the U.S. National Institute for Occupational Safety and Health (NIOSH), a special review article on Heap Leach Modeling, and articles from two Special Issues on Rare Earths. The 2017 Transactions consists of a total of 54 technical papers, encompassing all 21 papers published in 2017 in the Technical Papers Section of Mining Engineering (Vol. 69) and all 24 papers published in 2017 in Minerals & Metallurgical Processing (Vol. 34). Additionally, this volume contains 9 papers that are being published for the first time in this issue. The papers presented in this volume were written by some of the most distinguished professionals in the industry worldwide. All of the technical papers were peer-reviewed. The process of review and publication requires much hard work by authors, reviewers and our Publications staff. As the 2017 president of SME and on behalf of all our members, I would like to extend our gratitude to all whose volunteer efforts contributed to the publication of this volume.

Jan 1, 2017

By D. Tao

Coal is a major source of energy in the U.S. and more than 51% of the electricity used in the country is generated from coal. Coal cleaning prior to combustion is necessary and often accomplished using wet physical processes at coal preparation plants to remove impurities such as ash, sulfur, mercury. However, the resultant clean coal product still contains a significant amount of impurity due to the fact that impurities are not well liberated from coal particles ranging from several millimeters to inches in size at which wet cleaning processes take place. A cleaner coal product can be obtained if a cost-effective dry process is developed to further clean pulverized and thus better liberated fine coal at the power plants prior to its combustion. The benefit of such a process is a significant reduction in the cost of expensive post-combustion chemical cleaning processes such as flue gas scrubbing employed to meet the stringent environmental air quality regulations. In this study, a novel rotary triboelectrostatic separator (RTS) was investigated for its application to dry cleaning of fine coal samples acquired from the power plants in the state of Illinois. The pulverized fine coal contains well liberated ash and pyrite minerals and is an ideal feed to the triboelectrostatic separator for further cleaning without the use of water or any chemical reagents. The proprietary rotary triboelectrostatic separator (RTS) is characterized by an innovative high efficiency rotary charger, charger electrification, laminar air flow, and specially designed electrodes. Compared to existing triboelectrostatic separators, the rotary triboelectrostatic separator offers significant advantages in particle charging efficiency, solids throughput, separation efficiency, applicable particle size range, etc. Testing with several fine coal samples has demonstrated that this technology can significantly reduce ash content with a process efficiency similar to or better than froth flotation. Important process parameters such as charger rotation speed, injection and co-flow rate, feed rate were investigated for their effects on separation performance.

Jan 1, 2010

By K. E. Robinson, G. Re, L. Skoski

Introduction A new technology is evolving as a result of growing industry and government concerns over the potential impacts of possible airborne emissions from uranium tailings piles. A major component of the technology is the use of earth covers to stabilize the tailings after mill operations have ceased. While various analytical models have been used to predict the thickness of required covers, experimental validation of the models has been necessary. This paper presents the results of a field program to select and test cover material to determine its suitability for eventual reclamation of a currently active tailings pile. The two main criteria guiding the study were the U.S. Nuclear Regulatory Commission radon flux requirements (reduction to less than twice background pre-1979, and to 2 pCi/m2 -sec above background post-1979) and the desire to employ locally available material. The methodology chosen for this study consisted of three main elements: o Determination of the background radon flux. o Determination of the radon flux from the tailings pile. o Experimental determination of the cover material diffusion coefficient and and calculation of cover thickness. The first two elements of the study are relatively straightforward, the last phase is discussed in detail. Background Radon Flux Measurements of radon-222 emanation rates from the surface of the ground were taken at three sampling locations. Samples were collected by means of the accumulator can method described by Wilkening, 1977. Both morning and afternoon samples were collected at each site to obtain an average. The measured fluxes were fairly uniform and did not differ greatly among sites. The overall average flux for all sites was 0.63[+]0.28(o) pCi/m2 -sec. This value is equal to the average radium-226 concentration determined in the soil, thus yielding a one to one ratio of radon-222 emitted (in pCi/m2 -sec) to soil radium content (in pCi/g). Tailings Pile Radon Flux Two sites on the tailing pile

Jan 1, 1980

By Wenhua Li, Tsuyoshi Adachi

Resource nationalism is essentially mandatory government intervention in natural resources businesses by political or economic means in order to benefit the nation and the people. It is attacking the mining industry more and more rampantly by all kinds of means since the twenty-first century. Poor countries who count on a resource-led economic growth usually find themselves trapped into “resource curse”. The harmfulness of resource nationalism for investors is that one event can quickly escalate and lead to a chain of events which make projects commercially unavailable. In spite of historical and theoretical social investigations in the causes of resource nationalism, rare studies engaged in quantification of dominant parameters of it. The objective of this study is to find significant factors that dominate the occurrence of resource nationalism for important metal and energy resources producing countries and quantify their marginal effects. The study applies binary choice logit model for panel data using pooled method. One feature of the research is that binary data set of occurrence of resource nationalism are sorted out by authors referencing U.S. Geological Survey’s reports. The results indicate that high-technology export (% manufactured export), ores and metals exports (% merchandise exports), rule of law (world governance indicator), trade (% GDP), and natural resource rent except forest (% GDP ) dominant the occurrence of resource nationalism for high and upper middle income group countries; government effectiveness (world governance indicator), policy perception index (The Fraser Institute), high-technology export (% manufactured export), and mineral rent (% GDP) dominant the occurrence of resource nationalism for lower middle and low income countries. According to our model, probability of occurrence of resource nationalism in 90 countries are predicted. Top 10 risky countries in 2012 are estimated to be North Korea, India, Honduras, Indonesia, Kazakhstan, Burkina Faso, Mongolia, Cuba, Bolivia, and Peru. The study is a primary trial of researching on resource nationalism and provides some insights for theoretical building and simulation on the issue.

Jan 1, 2017

By Hilal Soydan, H. Sebnem Düzgün, Jurgen Brune

In this study, with the primary goal of capturing ongoing digital transformation and automation impacts on the mining industry and its workforce, we conduct several interviews with mining industry experts in the United States and analyze our survey reports qualitatively and quantitatively through exploratory analysis. After the interpretation of the insights of industry experts, we proceed to generate a personalized and customized data analysis through a novel metric based on skills, knowledge, competencies and occupational requirements, which quantifies the job similarities for occupations in the mining industry based on the publicly available database of the U.S. Department of Labor. We use text analytics to tokenize and classify the interviews to capture a better understanding of major response categories. The temporal analysis shows that the critical competency needs in the data science and autonomy category increases from 28 percent in current demands to 43 percent. In defining our metric, we also calculate Kullback–Leibler (KL) divergence for each job profile that enables determining whether and to what extent that job is transitionary in our test set based on the mean, standard deviation and kurtosis of each job of interest. Our analysis reveals that the in-group job transitions are significantly easier than the between-group transitions, proving our initial assumptions and common sense. The generated heat maps provide the opportunity to present the gap between the current job and desired job profiles that provide feasible career change options, among others, offering individualized career paths for job seekers and promoting potential job transitions. Through the collection of industry-specific individual employee data, the AI system is envisaged to continue to learn as end users engage with the system, thus creating a central data hub specifically for the future workforce in the mining industry. Although the study has limitations on generalizability for qualitative assessments, it presents itself as a valuable application of how qualitative and quantitative approaches could be of value for future worker training in the mining sector.

Feb 1, 2025