Search Documents

By S. C. O?Brien

This paper develops the procedure for simulating the special locked-cycle Work Index laboratory test using the kinetic parameters obtained by conducting standard size-mass balance (SMB) grinding tests and presents the results for three materials - quartz, a taconite iron ore and a bituminous coal. It was found that the WI could be determined by simulation; however, if a material breaks abnormally, a full description of its abnormal breakage is necessary. It was also found that the sensitivity of the WI test procedure to the sieving process and the estimating of the 80% passing size of the sieve undersize is sufficient to question the practice of quoting a WI to two or more decimal places. Finally, if a material grinds abnormally in the Work Index mill, then the WI test should not be conducted.

Jan 1, 1987

By A. Khan

The effect of sulfur dioxide on collectorless and collector induced flotation of chalcopyrite was studied by cyclic voltammetry on a rotating disc electrode. Contact angle measurements were made to determine the effect of sulfur dioxide concentration and electrochemical treatment. The benefits of sulfur dioxide in enhancing the selectivity of separating chalcopyrite from complex sulfide ores are discussed.

Jan 1, 1996

By D. Williamson

In the post war years metals analysts and statisticians have generally tracked the demand for metals in line with changes in OECD industrial production (IP) growth rates because, undoubtedly, the correlation between IP growth and metal demand was reasonable. However the correlation was exaggerated. During times of expanding IP growth metal demand increased at a faster proportional rate than IP growth. This was probably due to industry restocking in anticipation of growing demand at the start of each economic cycle. Conversely, metal demand would slacken at a greater rate than would be suggested by negative IP growth as industry destocked in order to reduce costs. Nonetheless, overall, a reasonable correlation between IP growth, over the longer term, and metal demand could be painted. Yet, although this correlation has stood well since the last world war it has been based on the fact that the bulk of the world's IP growth stemmed from the industrialized countries of the western world, latterly including Japan. The so called "developing world" was of little consequence, whilst countries of the Soviet Union and Communist Bloc were deemed to be closed, self-contained entities which, for each metal, would either be net exporters or importers. These quantities would be used by analysts to calculate the overall supply/demand equation for the western world only and to deduce whether a commodity was in shortage or surplus. It is now believed that this method of projecting total world supply and demand for raw materials is outdated and takes little account of the worldwide political changes which have occurred since the collapse of communism and the revitalization of China, albeit under a notional communist government. It is no longer appropriate to assess global balances for raw materials on the basis of three economic blocs namely, western world, developing world and communist bloc. Rather, global balances need to be projected on a global basis. In this regard, since the collapse of communism and the removal of many other totalitarian regimes, capitalist forces are at work and are attempting to satisfy, with some considerable success, the expectations of the great mass of the world's poorer people. Such people, usually located in Asia, Africa and Latin America have aspired to the same standard of living as people living in western Europe, North America and Japan. Now, with free market forces at work their aspirations will start to be met. Consequently, the demand for metals and other raw materials will now rise at a much faster rate than at any other time in the world's history. Not only will the production of raw materials have to keep pace with rising IP in the developed world but will also have to keep pace with the demands associated with the rising expectations of rapidly increasing populations in the developing world, as well as from within the old communist bloc countries. This paper sets out to argue the case that metal demand could well increase at a rate faster than the world's mining companies, governments and financiers can deliver.

Jan 1, 1997

By Fulian He, Jianhang Chen, Dongdong Chen, Shoubao Zhang

"The Wangjialing Coal Mine is the main colliery of the China Coal Huajin Energy Limited Liability Company. The average thickness of the coal seam in District 201 is 6.21 m. Fully mechanized longwall mining was used in this district. The ventilation roadway of panel 20102 was influenced by the retreat mining of the adjacent panel 20104. Therefore, large deformation and severe roof falls occurred in this roadway, seriously influencing the safety production of this coal mine. To support the roadway, cable truss was proposed to strengthen the reinforcement of this ventilation roadway. First, numerical simulation was used to optimize the reinforcement parameters, including the cable installation angle, cable length, and eccentric distance. Based on numerical simulation results, in-situ tests were conducted in the ventilation roadway of panel 20102 with the cable truss technology. In-situ monitoring results showed that the roof-to-floor convergence and the convergence of roadway on two sides were within the safety range. Furthermore, no apparent separations occurred in the roof. These indicate that based on the designed parameters, the cable truss system can effectively maintain the roadway stability under the severe influence of the adjacent longwall mining.INTRODUCTIONCable bolts are flexible tendons composed of multi steel wires, which are wound into a strand (Chen, Hagan, and Saydam, 2018). They were initially introduced in the hard rock mining industry in the 1960s. Later, they found rapid application in coal mines to maintain the stability of excavations (Wang et al., 2015).The standard cable bolt is composed of seven steel wires with a diameter of 15.2 mm. Laboratory and in-situ tests showed that there is a low bonding capacity between the standard cable bolt and the grout (Craig and Holden, 2014; Chen, Hagan, and Saydam, 2018). Then, modified cable bolts are developed based on the standard cable bolts. They are improved by changing the surface geometry of standard cable bolts, such as birdcaged cable bolts (Hutchins et al., 1990) or nutcaged cable bolts (Hyett et al., 1993). Further tests proved that modified cable bolts have better mechanical interlock and friction between the cable bolt and grout, leading to larger load transfer capacity of cable bolts.Although cable bolts have been used for many years, failure of the cable bolting system still occurs. A common failure mode is the damage of surrounding confining medium while the cable bolt is still hanging in the roof, which is caused by the bond failure of the cable/grout interface (Hutchinson and Diederichs, 1996). To prevent the cable bolting system from failing, the cable truss system is more widely used in mining engineering."

Jan 1, 2019

By Tsunenori Shibata, Kazunori Jimbo, Kaoru Toya, Masafumi Matsumoto, Jinya Mitsui, Toshinori Tsuji

"The Toyama Line is under construction as a natural gas pipeline with a length of 102 km from Itoigawa City to Toyama City. A 2 km-long tunnel section of the pipeline that we are reporting here is being excavated in a mountain area away from an urban area. The geology under which the tunnel is constructed is collapsible fractured breccia slate and Holocene sandy soil. Other tunnels of the Hokuriku Expressway and Hokuriku Shinkansen are in service above the tunnel route. From the starting shaft on Toyama side, conventional tunneling was adopted to facilitate excavating the base rock layer and maintain enough distance from the Hokuriku Expressway tunnel. From the starting shaft on the Itoigawa side, TBM tunneling was adopted to cope with the unconsolidated soft ground for a 200 m-long section from the shaft. We will discuss the issues and countermeasures concerning the selection of a tunnel route and excavation methods, performance of both conventional and TBM tunneling, and underground connecting of these tunnels excavated by conventional (NATM) and TBM methods under a high groundwater pressure up to 1.2 MPa. INTRODUCTION AND BACKGROUND The International Petroleum Exploration Teiseki Co., Ltd. (INPEX) is constructing a high-pressure main pipeline network in the Toyama Prefecture area to promote the use and reliable supply of natural gas as shown in Figure 1. As part of the Toyama line project that has a total length of 102 km, A-1 construction, the nearest section to the tunneling starting point in Itoigawa City, where various tunnel excavation methods have been adopted to install the high-pressure pipeline 20 inches in diameter, a 2 km tunnel in the A-1 construction section discussed here is to be excavated by conventional and TBM methods in a mountain area. Based on environmental studies such as traffic jams due to frequent traffic of heavy vehicles disposing of soil, and the effects of dust, noise and vibration during construction, we selected the route to install the gas pipeline in a mountain area as shown in Figure 2, where the impact on the surrounding environment could be minimized."

Jan 1, 2016

By N. Sahin, M. Can, Z. Ekmekçi, Y. Öztürk, Ö. Biçak, I. B. Çelik, B. Kocabiyik

"In this paper, a case study from Çayeli Bakir Isletmeleri A.S. (Rize, Turkey) about the selective flotation of copper minerals from sphalerite is discussed. Çayeli Cu-Zn Sulfide Ore contains different ore types, such as yellow ore, clastic ore, bornite-clastic ore, bornite-yellow ore, and black ore. For some of these ore types, selective flotation of copper and zinc is very difficult presumably due to presence of secondary copper minerals such as bornite, chalcocite and covellite, and also surface oxidation. These factors affect Cu-Zn selectivity due to activation of sphalerite particles in the ore during the process. The main objective of this work was to improve Cu-Zn selectivity by optimization of the pulp chemistry for different ore types of Çayeli ore. After preliminary flotation tests investigating effects of different chemical conditions, a plant survey was performed to determine the plant performance and sources of the problems when problematic bornite-clastic ore is treated in the plant. Various chemical conditions are tested in the laboratory scale test for better depression of sphalerite in copper flotation circuit. Combination of Na2S+ZnSO4+MBS was found to be the most effective depressant scheme. INTRODUCTION Ore variability is one of the most important factors affecting performance of a process plant both in short and long term planning. The geometallurgical modelling becomes a common tool to determine ore variability problems and develop the most efficient solution during life of mine (1, 2). Flowsheet design and equipment selection and sizing are usually done based on the results of ore variability test works. However, in some cases ore variability may not be foreseen during the design stage and therefore the solutions should be developed based on the existing flowsheet and equipment in the plant. In this situation, ore characterisation, problem statement and diagnostic testing should be applied step by step. The problem could be due to changing feed grade, mineralogical characteristics, grindability and surface characteristics when flotation is involved. The variability in feed grade with fixed mineralogy can be handled with relatively simple modifications (i.e. adjusting throughput or equipment capacity) in the plant. Variability in ore mineralogy is the most complex and difficult problem to tackle. Because, mineralogical variations could bring variations in mineral composition, texture and liberation. These variations can potentially lead to the variations in grindability of the ore and flotation behaviour. Variations in grindability are usually managed by optimization of operational parameters in grinding circuit, as it would be costly to replace the existing equipment in the circuit (3). The variations in flotation behaviour are mainly due to variations in mineral types and distribution, texture and surface oxidation. One or all of these factors could be observed in a flotation operation. Therefore, a comprehensive investigation both in plant and lab scale should be conducted for definition of source of the problem. The testwork to solve the problem and retrieve the performance is planned and conducted depending on the source of the problem (4, 5)."

Jan 1, 2017

By R. Bishop, J. Baggett, J. Monsalve, J. Hole, N. Ripepi, A. Abassi

This work focuses on the operational and safety issues associated with karst voids in large opening underground mines. Issues include water inrush, structural instability, and engineering uncertainty in these environments. Coupled with the fracturing prevalent in folded sedimentary rocks, karsts are complex and challenging ground control risks. Traditional methods of predicting karst locations, such as probe drilling, are impeded by the inconsistent spatial distribution and variable sizes of the features. Ground penetrating radar (GPR) is a geophysical technique that transmits radio waves into a medium and subsequently detects reflected waves via a receiver. The travel time and energy of received signals are then processed and interpreted. The difference in material properties between limestone and open karsts causes strong reflections. GPR is frequently used as a geophysical surveying technique in several industries, however there is a lack of published research on underground mining GPR applications. The purpose of this work is to prove the viability of GPR in underground stone mines for karst detection, and to discuss the importance of karst detection ahead of mining. INTRODUCTION The Mine Safety and Health Administration (MSHA) currently lists 116 active underground stone mines in the United States, the vast majority of which extract limestone for crushed stone products. These limestone mines have the potential to encounter karst voids at some point in their operation, as most karstic regions of the United States develop in limestone rock masses (Kuniansky, Weary, & Kaufmann, 2016). Karsts, the cavities formed by the dissolution of carbonate rock, have long plagued the mining and tunneling industries, as well as been a hindrance on the Earth’s surface, producing sinkholes and ruining otherwise valuable land for construction and public use. The impact of karsts on the Gavarres tunnel in Spain is well documented by Alija et al; constant instability conditions, material spills into the tunnel, and unexpected cavities seriously delayed the project deadlines and “were not foreseen in the design” (Alija, Torrijo, & Qunita-Ferreira, 2013). At the water supply project in Sohngua River, China, Bin et al detail the presence of both water and sediment filled karsts which are sources of disastrous conditions at this tunnel (Bin, et al., 2017). A hydrological tunnel in Lebanon encountered numerous massive karsts in the tunneling path which required remediation via friction anchors, rockbolts, welded wire fabric, channel steel arch segments, invert steel beams, and shotcrete (Leech, Jaoude, & Ghanem, 2008). From a design standpoint, rock mass classification schemes, such as the RMR from Bieniawski and the Q-system from Barton, are not able to represent the true nature of a karstified carbonate rock mass, and therefore complex case-by-case analyses of underground conditions are necessary (Andriani & Parise, 2017).

Jan 1, 2019

By F. S. Knoll

Magnetic separation employing superconducting technology is now accepted within the Kaolin processing industry, proving the value of this technology and its ability to operate reliably even at the most remote site. Developments in superconducting magnet engineering, including cryogen free operation, combined with experience in mineral processing enables new forms of Wet and Dry superconducting magnetic separation to be developed. Applying the high magnetic force advantages at 5 T else available from such magnets to other materials is now a reality. High magnetic force mineral separating system developments are reviewed allowing the mineral processor to take advantage of a technology that is no longer confined to the laboratory.

Jan 1, 1997

By R. L. Russell

Production at Freeport Indonesia's Ertsberg open pit copper/gold mine started in 1972 at a rate of 7500 t/d. Mill throughput remained at that rate for a number of years until the discovery of the Ertsberg East (GBT) orebody. This discovery prompted three successive expansion stages from 1981 to 1988 that boosted production to 20,000 t/d. The discovery of the huge Grasberg porphyry copper deposit in 1988 launched a new era of much larger expansions. The first of these involved installation of a fourth primary mill in 1989 to bring production up to 32,000 t/d and was immediately followed by an expansion of the crushing and screening plant and the addition of a new south concentrator to bring production to 57,000 t/d in 1991. The addition of a primary ball mill and the changeout of the original Denver flotation cells in 1993 has served to optimize current production at a level of 66,000 t/d. A major expansion is now in progress. This includes construction of another new concentrator to house a SAG mill circuit and large Wemco flotation cells in an area created by the removal of 6,000,000t of glacial material. This current expansion, with a planned completion in 1995, will take production to 115,000 t/d. This paper describes the evolution of the Freeport Indonesia (FI) concentrator to-date and will then go into an in-depth discussion of the 66,000 and 115,000 t/d expansions.

Jan 1, 1994

By L. Sandbak

"CURRENT BASIS OF GROUND SUPPORT DESIGN ANALYSIS The current strategy used in determining what kinds of support are needed is based on empirical design charts (Grimstad and Barton, 1993). Figure 1 is an example of the topcut analysis used for a 14 foot wide (4.3 meter) drift, which is the current design width used for topcuts at TRJV mine. The majority of our topcuts are situated in ore of the Type IV and Type III weak rock class categories that necessitate the use of bolts, mesh and 2”-4” of shotcrete. This type of empirical chart gives excellent guidelines for the kinds of support, and it is based on case histories of civil tunneling and mining properties. It is a good starting point for determining the kinds of support needed, but not to the detail needed to optimize the number of bolts, type of mesh, or combination of types or strengths of shotcrete. This report is an attempt to help quantify the safety factor and optimum design parameters to include mesh and shotcrete as part of the design criteria and subsequent safety factor.SAFETY FACTOR ANALYSIS: BOLTS ONLY One type of safety factor analysis used at TRJV for the past 7 years is described as the “dead weight” method, developed by Pakalnis (2008). It involves the support of a conservative “dead weight” of rock held in place by bolts in which the depth of failure is approximated as a wedge whose height is one-half of the span. The failure or dead weight wedge resembles a triangular wedge that must be supported by the remainder of the bolts going through the wedge (see Figure 2).The support capacity of the system is determined by the bond strength of the bolts holding up the wedge, which is in turn based on the RMR. The method assumes the total support capacity is the sum of the individual bolt values defined by either the breaking strength or the bond strength of the bolts (whichever is lower) passing through the failure surface."

Jan 1, 2017

By Siyu Song, Yanhong Wang, Guohua Gu, Linbo Huang

In this study, the effect of cations, Na+ and Mg2+, in saline water on copper flotation in the presence of calcium bentonite was investigated. It was found that as the concentration of NaCl was increased, the copper recovery initially decreased and then increased to above 99%, while the copper grade initially increased and then decreased. In contrast, as the concentration ofMgCl2 was increased, the copper recovery continuously increased, while the copper grade continuously decreased. The variation of copper recovery and grade was mainly attributed to the synergistic effect of pulp rheology and flotation solution chemistry. The underpinning mechanisms are the compressing electrical double layer and ion-exchange interaction between saline water and bentonite, which occur at the same time. Using salinewater slightly affected the pulp rheologywith a decrease in copper recovery at low NaCl concentration. Increasing the concentration of cations in saline water might even facilitate the flowing out of exchangeable cations, especially divalent cations, from the interlayer space of bentonite to the solution, resulting in the decrease of copper grade at high salt concentration.

Sep 10, 2020

By Jorge Amaya, Nelson Morales Varela, Francisco Saavedra, Gonzalo Nelis, René Gómez

Precedence constraints are broadly used in mathematical models and algorithms for mine planning to model, for example, slope angles in open pit operations or connectivity in underground mines. Unfortunately, these constraints do not capture relevant geometrical aspects for the design of the mine like minimum bottom space of pits or smoothness of the economic envelope in block caves. In this work, we present different approaches that utilize precedence constraints generating economic envelops that are more suitable for design purposes. The numerical experiences show that the proposed techniques produce high value envelops with better geometrical properties and that the methods proposed can be computed efficiently.

Jun 25, 2023

By Rodrigo Peroni, Euler Victoria

Knowing the depth of contacts between weathering zones in phosphate mines is determinant to define the stripping ratios and the mineralized zones. Contacts are gradational and difficult to define even in the drillhole samples, so the combination with geostatistical simulation techniques helps to define the contact zone and the grade distribution, providing a way to assess the probability of the occurrence and the positioning of contacts between the barren waste and the ore zones. These inputs are used in the scheduling, anticipating risks associated with mine planning scenarios. The results from an application to a case study showed a good improvement when compared to traditional techniques.

Jun 25, 2023

By Hesam Dehghani, Farid Alimohammadnia, Nima Babanouri, Mokhtar Kalhori

In open-pit mining, blasting pattern design is performed to achieve a desired degree of fragmentation for loading, hauling, and crushing operations. Inappropriate fragmentation of rock will result in numerous problems such as incurring extra costs for secondary blasting, production interruption, etc. Wetness of the blast holes is one of the most important factors, which can cause the inappropriate rock fragmentation. Lowering ambient temperature in the vicinity of the explosion, the presence of water in the hole adversely affects the quality of the explosive while dissipating part of the explosion energy, ending up with inappropriate fragmentation problems. In the present research, in order to study blast-induced fragmentation conditions in Baba-Ali Iron Ore Mine, three scenarios were considered: explosion of ammonium nitrate with fuel oil (ANFO) in dry hole, explosion of ANFO in wet hole, and explosion of the emulsion in wet hole. For this purpose LS-DYNA, a numerical simulation code was used. Results of the present research showed that, compared to the explosion of ANFO in wet hole, the explosion of the emulsion produced more uniform distribution of fragment size, while the explosion of ANFO in dry hole resulted in fewer large fragments.

By Brajendra Mishra, Himanshu Tanvar

Niobium and tantalum extraction industries heavily depend on fluoride chemistry for metal oxide production. This study concentrates on developing a fluoride-free approach utilizing alkali treatment for selective dissolution of niobium and tantalum phases. The application of microwave heating in the alkali treatment of columbite significantly reduced the processing time, providing a higher reaction rate and recovery than conventional heating. A short duration of microwave exposure (6 min) elevated the sample temperature to more than 900 °C, resulting in the rapid formation of water-soluble niobium and tantalum complex. Metal recovery from the solution was attempted through direct precipitation using guanidine carbonate as the precipitating agent, resulting in a mixed oxide product with > 90% purity. On the other hand, solvent extraction was also attempted using methyltrioctylammonium chloride as an extractant, providing a niobium oxide and tantalum-rich mixed oxide with > 98% purity as the final product.

Mar 23, 2024

By C. H. Stephenson, Z. White

This paper presents the design approach case study for incorporating a Technogrid® conveyance End-of-wind arresting system within the new South32 Hermosa headframe. Focus is placed on energy absorption requirements, structural integration, and mounting details tailored to the geometry and operational constraints of the headframe. Key considerations include arresting forces, load path continuity, and connection design to ensure reliability and maintainability. The paper also discusses coordination with other headframe systems and the iterative design process used to meet safety standards and client objectives.

Feb 22, 2026

By Marshall D. Himes

The Pima mine, 39,000 ton per day copper mine, is located 17 miles south of Tucson, Arizona. The mine is in a sequence of Paelozoic and Mesozoic sediments striking east-northeast and dipping southeasterly intruded by a Tertiary quartz monzonite porphyry. The Paleozoic Permian(?) dolo¬mites, limestones, and sandstones have been altered to talc-silicate skarn, marble and quartzite. The overlying Mesozoic Triassic(?) clastic sediments have undergone some recrystallization and hydro¬thermal alteration. The clastic metasediments are divided into three distinct lithologic units, lithic arenite, arkose, and inter¬bedded and overlying black argillite. Three types of hydrothermal alteration in the clastic rocks are propylitic alteration (epidote, chlorite and quartz, with or without sericite), quartz-sericite alteration, and potassic alteration (K-feldspar and quartz, with or without sericite and chlorite). The porphyry has undergone potassic alteration. Dominant structures are an east-west post mineral fault in the western part of the pit, and strong low angle faulting and shearing which truncates the ore body at depth. Two joint sets, one parallel to bedding and the other at right angles to bedding are prominent in the mine. Faulting is in two dominant directions, one striking northwest, dipping northeast and the other striking northeast, dipping northwest. Mineralization is predominantly disseminated pyrite and chalcopyrite, and molybdenite-quartz veinlets. There are lens important amounts of magnetite, hematite, sphalerite, galena, tennantite and bornite. Mineralization is believed to be both structurally and chemically controlled.

Jan 1, 1972

By J. A. Herbst, H. R. Cooper, R. J. Brison, R. W. Harper, K. P. Ananthapadmanabhan, W. C. Hellyer, B. H. Bergstorm, D. M. Hopstock, H. Rush Spedden, W. C. Hellyner

Scope of Section The physical characterization of an ore or mineral mixture in such detail that mineral processing may be effectively applied to create more useful products is one part of the technology of sampling and testing. In addition, the evaluation of the multitude of separation processes, both physical and chemical, combined with ancillary opera¬tions and performed on samples at a laboratory scale, is another part of the testing procedure. Although analytical techniques provid¬ing quantitative determinations of elemental compositions are an im¬portant and necessary supplement to any testing program, that field of endeavor is a well-developed, separate entity beyond the scope of this Section. Sampling procedures cover the practice of selecting representative quantities of test materials in the field to evaluate mineral deposits, and extend to techniques of obtaining process samples in slurry and bulk ore as part of process evaluation. The same techniques are appli¬cable, of course, to standardized methods of metallurgical accounting. Sampling is also an important facet of successful on-line measurement of slurry properties such as assays and particle size in the practice of automation. However, the sampling methods in this case can be different from those needed for precise testing and accounting pur¬poses. Sampling was well defined in Taggart's Handbook as "the opera¬tion of removing a part convenient in size for testing, from a whole which is of much greater bulk, in such a way that the proportion and distribution of the quality to be tested (e.g., specific gravity, metal content, recoverability) are the same in both the whole and the part removed (SAMPLE). The conditions of the more stringent definition, that the sample shall be completely representative of the whole as regards all aspects save bulk, are practically never fulfilled when heterogenous mineral mixtures are sampled." Taggart's Handbook of Mineral Dressing, Section 19, "Sampling and Testing," continues to be a very useful compendium of principles and techniques, particularly as applied to manual methods for han¬dling samples. In the intervening years since its last revision, substan¬tial progress has been made in both the theory and the techniques; thus, this current contribution is designed to be an extension of the earlier work, yet complete enough to provide procedural guidelines to methods of continuing validity. Although basic principles of testing remain unchanged, the meth¬ods of applying those principles have undergone great change. New testing equipment has become available, yielding a greater precision of results. Testing methods have been refined which, in many cases, allows for a valid scale up of flowsheet designs without the necessity of costly pilot or prototype plant development. Justification for a Sampling and Testing Program* The proper evaluation of a mineral property is a complicated process. It often is done on a team basis with the exploration geologist, mining engineer, mineral process engineer (extractive metallurgist), economist, and product utilizer (ceramist, chemical engineer, chemist, metallurgist, etc.) all represented. The mineral processing engineer is a key member because he can provide a go no-go answer to the question, "Can this ore be processed economically?" In addition, his judgment on the response of even the initial sample to processing can be an invaluable guide to the proposed process and its mutations. Since the capital investment and operating costs are so sensitive to the type of process used, the judgment of the mineral processing engineer forms an important part of the early evaluation of the profitability of a new mining venture. This early estimation of the processing approach is all the more important since, for some metalliferous ores, the capital investment for mill, smelter, water supply, and tailings disposal exceeds the cost of the mine. At present, for commodities such as coal, the reverse is true. There is a smaller capital investment for the coal preparation plant than for the mine. In general, both the capital and operating costs escalate very rapidly in the following order: gravity concentration of alluvial deposits (e.g., dredging), gravity concentration of lode ores, flotation, simple hydrometallurgical processes, and complicated hydrometallurgical and pyrometallurgical processes. The latter two processes may cost 100 to 1,000 times more per ton treated than processing of a simple alluvial deposit. This dictates that the valuable mineral be concentrated as much as possible to minimize the total tonnage treated in the more expensive operations. Within each of these ore-processing categories there is a wide range of process sophistication and hence of capital and operating costs. Perhaps the greatest variations are in the chemical processing of ores. These range from the simple leaching of a copper waste dump to very sophisticated hydrometallurgical processing of ores in increasing order of cost. Because the overall cost of a mining venture is so sensitive to the process selected, it is essential that the mineral¬ processing engineer evaluate the ore in the initial stages of the development of an ore body. As better samples become available, he must continually revise his estimate of the process to be employed. The sampling and testing process must be a necessary and continuing activity throughout the life of a project. One fundamental aspect of nearly all mineral deposits is the inherent variability of the mineral assemblage and composition. A utopian goal of any processing plant is to have the process so flexible and so well-defined that an automatic process control system can optimize the economic recovery at all times. Since this is rarely possible, a continuing or at least a periodic testing program is desirable. Variables to be considered are: 1) Ore body inconsistencies. 2) Zonal variations. 3) Feed variations from mining plan or methods. 4) Variable performance of processing units due to wear. 5) Seasonal or other changes affecting processing conditions such as water quality, temperature, etc. 6) Changing market conditions for product quality or byproducts. 7) Technological advances in processing methods or equipment. 8) Increasing demands for environmental control. 9) Changing economics of competitive processes, of supplies, of capital investment vs. labor costs, etc. Sampling Procedures Preliminary Guidelines for Sampling Ore Deposit Studies. t At a very early stage, it is essential that the mineral processing engineer receive a sample of the ore. This may be a portion of the diamond drill core or a split from the trench, pit, churn drill, channel, or sheet sample. Even a grab sample may have some value, but it should be selected by the mining engineer or exploration geologist to be as representative of the ore body as possible within his best judgment. The sample delivered to the process engineer should have been subjected to as little prior crushing as is practical since fine sizes are difficult to concentrate. In addition, finely ground ores are readily oxidized and thus may give misleading test results. Furthermore, ground samples may make it impossible to eval¬uate either the comminution or the coarse-gravity concentration pro¬cesses. For an initial evaluation, a good deal may often be learned from a sample of only a few pounds if that is all that is available. To obtain the maximum information from a sample, its selection should be carefully discussed with the mineral processing engineer. In addi¬tion to being as representative as possible, the mineralogically distinct samples should be carefully segregated rather than composited. Since drastically different processes are often needed to process samples of differing mineralogy, considerable care and time must be exercised during this sample collection step. The segregation of samples showing gross mineralogical differences, such as the oxide caping on a sulfide deposit or a laterized zone, is easy. It is the more subtle changes in mineralogy that can often elude the field man. Yet these differences are often sufficient to dictate that an entirely different type of process be used. Obviously, the selection of these initial samples for ore testing and mineralogical studies requires that it be done by a man of consider¬able experience and judgment. While the mining engineer or field geologist is collecting these samples, he should also note and convey to the processing engineer such details as water quality and availabil¬ity, terrain, potential mill location, tailings-disposal areas, case of transportation, etc. As the property is developed with additional drill holes, adits, etc., larger and more representative samples will be required to develop the ore-processing flowsheet more adequately. If pilot-plant studies are required, a very large sample may be necessary. Though the type and amount of sample collected for flowsheet development investigations vary widely, gathering a representative sample of the ore body is a prime requisite for any process development effort. The process developed for any given ore body is only as reliable as the sample on which the flowsheet was based¬

Jan 1, 1985

By Richard M. Crowell

"As thorough sampling is usually expensive, the cost of a complete job is often unwarranted, and a cheaper approximation must be substituted. The engineer should, however, weigh the situation thoroughly before subscribing to an alternative other than an accurate assay basis on which to build his conclusion." Examination and Valuation of Mineral Property. R. Parks, 1949

Jan 1, 1994

By R. W. Bartlett

I first met Milton Wadsworth in 1951 as an eighteen year old junior taking his mineral processing course at the University of Utah. He guided my senior thesis, evaluating the then new polymer flocculants on settling uranium leached ore pulps. This was before ion exchange and solvent extraction. After my military service and a brief working stint at Kennecott he supervised my PhD work. He encouraged me to be active in AIME and its constituent societies, where both of us have been directors of AIME and presidents of TMS. He has been a consultant for research groups that I have managed. Above all, he has been my mentor and friend for nearly 45 years. Thus, I am honored and particularly pleased to receive 5MB's Wadsworth Award.

Jan 1, 1996