Search Documents

By J. L. Francke

This paper describes the practices and methods used in a study of Time Domain Reflectometry (TDR) as an inexpensive deformation monitoring tool in underground excavations at the Waste Isolation Pilot Plant (WIPP). The WIPP is being developed near Carlsbad, New Mexico, for the disposal of transuranic nuclear wastes in bedded salt 655 m (2 150 ft) below the surface. Data collected from WIPP geomechanical monitoring are used to characterize conditions, confirm design assumptions, and understand and predict the performance of the deep salt excavation. The geomechanical monitoring program encompasses numerous geomechanical monitoring techniques ranging from inspection of observation boreholes to advanced radar surveys. In 1989 TDR was introduced as a monitoring tool with the installation of 12.7 mm (0.5 in) diameter TDR cables in the underground excavations. In 1993, a new TDR system was installed in a separate location. Based on experience with the previous installation, enhancements were implemented into the new TDR system that: 1.) extended the period of performance by increasing cable diameter to 22.2 mm (0.875 in), 2.) increased accuracy in locating areas of deformation by aligning cables with nearby observation boreholes, and 3.) improved data acquisition and analyses using a standard laptop computer, eliminating the chart recorder previously used. In summary, the results of a correlation between the TDR signatures to nearby observation boreholes and geomechanical instrumentation will be presented.

Jan 1, 1996

By Michael Lenz

Predictive maintenance technologies including vibration analysis, tribology, infrared thermography, ultrasonic detection, and electrical measurements have been applied to large electric mining shovels. The predictive program was initiated on the P&H Model 2300 and 4100 electric shovels. The utilization of these technologies has shown the potential for improving electric mining shovel availability and minimizing maintenance costs. Predictive technologies provide the tools to assess machinery condition. Availability is enhanced by the condition based planning of component replacement. Maintenance costs are minimized by focusing resources through condition based prioritization.

Jan 1, 1997

By J. Ye

A comprehensive flotation study has been carried out on a Chinese fluorspar ore using the packed flotation column developed at Michigan Technological University. The results are compared with that of a conventional mechanical flotation method on the same feedstocks. Key factors controlling flotation performance of both methods are evaluated based upon a simple statistic design. The flotation concentrate produced in one stage of the packed column has 4-S% higher recovery and much lower silica impurity content than that produced by up to six stages when a conventional mechanical cell is used. The results also show that the packed column flotation process is particularly suitable for recovery of finer fluorspar particles.

Jan 1, 1992

By J. M. Mutmansky

This paper outlines patterns of methane emission in both longwall and room-and-pillar operations and the effects that these patterns have on the decision as to whether the methane is most economically handled by ventilation alone or by means of a methane drainage system in addition to ventilation. The costs of handling the methane in the ventilation system and the costs of implementing the methane drainage system will be discussed as well as the costs related to the production of coal. The important issue of production slowdowns and gas outs will also be discussed as well as the proper response of mine management to such a situation. Suggestions concerning the keeping of production records related to methane problems will be made as well as justification for more intensive economic analysis of coalbed methane extraction and utilization.

Jan 1, 1998

By L. B. Phelps

This paper focuses on the use of an integrated mine planing software package entitled "REMINE" which was constructed to provide a project evaluation tool for analysis of remining projects. Coal remining constitutes the affecting of sites which have had a past history of mining and have a pre-existing pollutional discharge. Such sites require a Best Professional Judgement (BPJ) analysis. The program was written to provide such an analysis with flexibility in the mine plans which can be analyzed. The process required for a BPJ analysis will be detailed and mine plan simulation performed to demonstrate the analysis.

Jan 1, 1990

By C. C. Harvey

As we move towards the 21st Century there are several factors that will influence the markets and processing requirements for industrial minerals. Traditional markets for many industrial minerals in the developed world are frequently stagnant or decreasing because of their maturity or due to environmental factors such as reclamation, recovery of byproducts, and recycling. Some industrial minerals are greatly affected by these factors, while others are either immune to or have adapted successfully to meet these challenges. In the developing countries of the world, there is rapid market growth and resource exploitation. The future of specific mineral commodities in several markets will be discussed.

Jan 1, 1997

By Arthur E. Lewis

A contained nuclear explosion is proposed to produce a chimney of broken ore well below the water table. After the chimney is filled with water and reaches hydrostatic equilibrium, oxygen, under pressure, is introduced near the bottom of the mass of broken rock. The increase in solubility of oxygen at high hydrostatic pressure is sufficient to initiate the oxidation of the primary sulfides: chalcopyrite and pyrite. The oxidation and dissolution of these sulfides produces enough heat to increase the temperature of the ore and water in the chimney as much as 1000 to 150°C. The rate of dissolution of chalcopyrite becomes so rapid under these conditions that the rate of recovery is no longer limited by the rate of chalcopyrite dissolution, but by the degree of exposure and other factors. Means of solution control and distribution of oxygen in the chimney have been examined in some detail. A calculational model utilizing experimentally determined solubility rates is utilized to estimate the temperature rise in the chimney and the rate of copper recovery as a function of initial temperature, sulfide content of ore, size of sulfide particles, and fraction of sulfide exposed to solution.

Jan 1, 1972

By K. A. Natarajan, M. K. Yelloji Rao

Significance of grinding media wear and its effect on chalcopyrite flotation are discussed. Laboratory marked ball wear tests were conducted grinding chalcopyrite ore and quartzite dry, wet, and with collector added during grinding. The effects of oxygen and nitrogen on ball wear were evaluated by the addition of chalcopyrite mineral while grinding quartzite. The effect of dry and wet grinding on chalcopyrite flotation was also studied. Results show abrasive wear is greater in quartzite grinding than in grinding chalcopyrite. Oxygen increases the corrosive wear of high carbon low alloy steel balls in the presence of chalcopyrite ore. Chalcopyrite flotation was retarded due to wet grinding in the presence of oxygen. Though collector reagent increased the media wear, it improved the flotation of chalcopyrite. Probable electrochemical reactions encountered in a grinding mill are outlined.

Jan 1, 1991

By J. Davitt McAteer

Improvements in the control of coal mine dust have occurred over the past 25 years. Simultaneously, dramatic improvements in coal mine production technology have occurred, particularly at mines where longwall systems are in use. Production rates of longwall systems have quadrupled since 1978, and dust generation on these systems has significantly increased. However, technology to address control of the resulting increased levels of respirable dust has not kept pace, and many high-production longwall sections continue to experience problems with respirable dust control. This paper seeks to enlist the entire mining community in the effort to resolve the health problems presented by excessive levels of respirable coal mine dust, particularly on longwall systems. These systems are expected to increase in number and length, and to generate increasingly higher levels of dust as production rates of these systems continue to rise.

Jan 1, 1995

By D. Wheeler

Similar to modern day petro-chemical processes, the flotation column is a complete break from the conventional manner of floating on a batch basis in cells. The column has a reputation of being only suited for cleaning applications, particularly that of molybdenum cleaning. The original column, invented and developed by Column Flotation Co. of Canada, Ltd., was developed as a Rougher-Scavenger. Only after proving its capability in this field was cleaning allowed. One rougher-scavenger column in closed circuit with a cleaner column produced better grade and recovery than a conventional cell plant consisting of one stage of roughing, two scavenging and four stages of cell cleaning. Three cleaner columns replaced 13 stages of conventional cell cleaning and resulted in higher grades and recoveries. The gentle countercurrent action of the column itself together with complete automatic control enable this machine to produce such results.

Jan 1, 1986

By Dae S. Young, Steven F. Hoerger

The geostatistical method of indicator kriging (IK) was extended to analyze two-dimensional distributions of rock joint orientations. The IK method provides a non-parametric approach for spatial analysis of local probability distribu- tions. By taking into account the spatial correlation of rock joint outcomes and the relative geometry between estimation unit and samples, the IK method provides optimum, spatially conditioned estimates. The estimation method was tested by comparing distributions of actual mapped rock joint orientations with their corresponding kriged estimates. The comparisons show the unbiasedness and accuracy of the non-parametric approach for estimating local probability distributions.

Jan 1, 1986

By Robert G. Bottge, Paul C. Hyndman, Don J. Barnes, Clark A. Roberts

The effect of Federal restrictions on Federal mineral estate in Alaska and the Western States is being addressed by systematic, State-by- State studies. The Bureau of Mines has inventoried and classified 3.5 million sq km (876 million acres) of land, section-by-section, according to 1) mineral ownership, 2) availability for mineral exploration and development as affected by Federal restrictions, and 31, areas containing mines and mineral resources. The availability of Federal land for exploration and development is spatially compared to areas containing mines and mineral resources. The methodology and overall results of the studies are presented.

Jan 1, 1991

By C. E. Jordan

Abstract. The U.S. Department of the Interior, Bureau of Mines, as part of its effort to maintain an adequate supply of minerals and metals to meet national economic and strategic needs, is conducting research on the pneumatic recovery of coarse mica. A system of crushers, screens, and zigzag air classifiers is used to concentrate coarse liberated mica particles from mica ore and from the waste tailings of abandoned mica operations. The plus 0.21-millimeter-size mica is effectively recovered by this method. The mica concentrates produced contain over 90 percent mica. The method recovered up to 78 percent of the mica in the samples. As a dry concentration method, the pneumatic-beneficiation technique may be advantageous in areas of limited water resource.

Jan 1, 1980

By Raul A. Deju

This paper shows how one can relate the chemical reactions between water and a silicate bed to the equations of flow. First the reaction mechanism is studied both theoretically and experimentally. Once the reaction mechanism is established, the equations of flow are solved and a solution (under physically reasonable side conditions) is obtained. Experiments to substantiate the solution are also presented.

Jan 1, 1969

By M. Raffaldi, J. Johnson, M. Stepan, D. Benton

"The Office of Mine Safety and Health Research (OMSHR), Spokane Mining Research Division (SMRD), is continuing its High-Energy High-Displacement (HEHD) testing of field-scale shotcrete panels. A test program was developed to determine the relationship between applied force, displacement, and energy for both unreinforced and reinforced shotcrete panels. Reinforcement options consisted of synthetic macro-fibers, sprayed polyurea liners, chain-link fence, welded-wire mesh, and combinations of these products. During testing, photogrammetry was used to measure the geometric changes of the panels, including volume changes and panel cracking. These measurements were correlated with the load and displacement data, allowing visual observation to be related to the applied force and displacement. The test results provide a comparison of the mechanical performance of the various panel types and can be used by the practicing engineer to evaluate installed support based on visual observation of cracking and deformation. Visual assessment of the loading cycle and strength capacity of shotcrete in underground excavations will improve mine safety by providing a means to quantify the stability of installed shotcrete support. INTRODUCTION The National Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health Research (OMSHR), Spokane Mining Research Division (SMRD) is continuing research on the behavior of shotcrete when used as the surface support component in mining ground support systems. Ground control safety often depends on supporting, or at least containing, the ground between the rockbolts. Shotcrete and mesh, in various combinations and with other components, are often used to accomplish this (see Figure 1). Maintaining support pressure during ground deformation is key to the performance of these systems, and to ensuring miner safety. However, the toughness of a ground support system–the ability to maintain strength over large deformations–is difficult to quantify. Researchers at SMRD have responded to this deficiency by designing a full-scale test device, described previously by Martin et al. [2015a], and beginning a testing program to assess the behavior of shotcrete surface support reinforced with a variety of products including: fibers, chain-link mesh, welded-wire mesh, spray-on polyurea liners, and combinations of these products. This paper presents the findings of these tests."

Jan 1, 2016

By B. Anamaeric

Economic, environmental and operational disadvantages of the traditional blast furnace process has led to the development of direct smelting reduction processes, including those that utilize self reducing/ fluxing dried greenballs as iron oxide feed materials. This is mainly due to improved carbothermic reduction, carburization and reaction kinetics. In this paper, the morphological changes of the greenballs as they transform to pig iron nuggets are examined over time at a constant temperature of 1,400° C. The products produced after each treatment were characterized using optical microscopy, scanning electron microscopy/energy dispersive spectroscopy and point counting/image analysis. The changes in the percent metallized area, wustite dendrite and slag matrix content of the structures were calculated. It was determined that the transformations were initially controlled by dissolving and containment of iron oxides in the molten slag and their consequent reduction to iron, followed by coalescence of the metallized areas. The final transformations were controlled by the carburization of the metallized areas.

By M. Raffaldi, J. Johnson, M. Stepan, D. Benton

"The Office of Mine Safety and Health Research (OMSHR), Spokane Mining Research Division (SMRD), is continuing its High-Energy High-Displacement (HEHD) testing of field-scale shotcrete panels. A test program was developed to determine the relationship between applied force, displacement, and energy for both unreinforced and reinforced shotcrete panels. Reinforcement options consisted of synthetic macro-fibers, sprayed polyurea liners, chain-link fence, welded-wire mesh, and combinations of these products. During testing, photogrammetry was used to measure the geometric changes of the panels, including volume changes and panel cracking. These measurements were correlated with the load and displacement data, allowing visual observation to be related to the applied force and displacement. The test results provide a comparison of the mechanical performance of the various panel types and can be used by the practicing engineer to evaluate installed support based on visual observation of cracking and deformation. Visual assessment of the loading cycle and strength capacity of shotcrete in underground excavations will improve mine safety by providing a means to quantify the stability of installed shotcrete support. INTRODUCTION The National Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health Research (OMSHR), Spokane Mining Research Division (SMRD) is continuing research on the behavior of shotcrete when used as the surface support component in mining ground support systems. Ground control safety often depends on supporting, or at least containing, the ground between the rockbolts. Shotcrete and mesh, in various combinations and with other components, are often used to accomplish this (Figure 1). Maintaining support pressure during ground deformation is key to the performance of these systems, and to ensuring miner safety. However, the toughness of a ground support system–the ability to maintain strength over large deformations–is difficult to quantify. Researchers at SMRD have responded to this deficiency by designing a full-scale test device, described previously by Martin et al. [2015a], and beginning a testing program to assess the behavior of shotcrete surface support reinforced with a variety of products including: fibers, chain-link mesh, welded-wire mesh, spray-on polyurea liners, and combinations of these products. This paper presents the findings of these tests."

Jan 1, 2016

By C. J. Johnson, C. J. Bise

Abstract - As the US coal industry moves into the next century, it is becoming more apparent that the effective application of new technology is the only way it can remain competitive in the energy marketplace. Examples of this emphasis are with us today in such diverse areas as face- ventilation and excavation-equipment applications. The focus of this new technology is directed toward improvements in health and safety, cost control, and productivity. Room-and-pillar mining accounts for approximately 68% of the nation's underground coal production; this percentage is not expected to decrease markedly in the near future. As such, this paper analyzes the impacts of the changing techno- logical climate on future room-and-pillar operations by comparing a base-case section (current) to three scenarios incorporating new or emerging technology. A microcomputer-based comparative analysis will reflect the changes in section production and costs.

Jan 1, 1990

This paper presents the latest developments in the flotation model being developed collaboratively between the Julius Kruttschnitt Mineral Research Centre in Brisbane, Australia, and the Mineral Processing Research Unit of the University of Cape Town in South Africa as part of the Australian Minerals Industries Research Association (AMIRA) P9 Project. It includes: - characterisation of flotation cells using the bubble surface area flux, Sb; - relationship of Sb to the overall flotation rate constant; - determination of the froth recovery factor; - evaluation of ore floatability; - modelling of entrainment - development of the Floatability Characterisation Test Rig (FCTR); - use of the model in design and optimization of flotation plants; and - current and future work.

Jan 1, 1999

By Richard J. Lewandowski

Corrosion and product contamination have been difficult problems for extractive metallurgy industries in the U.S. because of the highly active chemicals used. During the past twelve years, other industries, particularly the chemical and paper segments, began to combat this problem with some degree of success using newer materials of construction, including reinforced plastics. These materials are made by combining a corrosion resistant thermosetting resin with a glass fiber reinforcing material and are used to con¬struct hoods, stacks, blowers, tanks, towers, pipe, and equipment of the most complex configurations. For service in contact with aggressive chemicals, the equipment is most often fabricated with the bisphenol-A fumarate polyester resins because of their resistance to corrosive attack. Data from both laboratory work and case histories of field applications are presented-for many common chemicals found in extractive processes. Information is also presented concerning design standards and recommended construction procedures

Jan 1, 1970