Search Documents

By C. D. Broadbent

Open pit blasting can be a low cost routine or a high cost bottleneck depending on geology, environment and the operator's ability to master site conditions. Because blasting is a repetitive operation, there should be ample opportunity to optimize the process; but ordinarily this optimization is rarely achieved and then only if conditions remain consistent and predictable. Often, however, and particularly with porphyry coppers, hidden differences in rock characteristics nullify the operator's best efforts. At a porphyry copper deposit being mined by Kennecott Copper Corporation, there are all of the following rock types: oxidized and fresh porphyry, altered and silicified limestone, explosion breccia, rhyolite, sandstone, shale and several others. The units can cover large areas or be limited to a few tens of feet in maximum dimension. They are rarely visible on the bench surface and often do not show up in the bench slope. Even though the blastability of these rocks varies substantially, a generally-uniform blasting pattern was formerly used with disappointing results. Secondary blasting was often required and high bottoms occurred frequently; overblasting wasted drilling time, and explosives caused excessive throw. Several possible methods for improving the blast design were considered and a geophysical method was chosen for testing. There had been reports in the journals that seismic methods were being used in Europe as aids for blasting design. A literature search turned up work by Haxby 1/ on use of a refraction seismograph for measuring pit bench rock strength. Using his work as a springboard, equipment was purchased and a program was planned and carried out for developing, evaluating and implementing the seismic method for routine mine use. Following are discussions of the development program and results.

Jan 1, 1974

By Ernest E. Thurlow

"Western Coal" in this paper is limited to those deposits of subbituminous coal and lignite in the States of Montana, Wyoming, and North Dakota. The characteristics of the coal are discussed as well as the history of mining and current mining operations for steam coal. The future of the region is tied closely to the ultimate conversion of coal to oil and gas products. Problems of industrial water supply and environmental considerations are covered together with a brief review of current legislation's actions affecting strip mining.

Jan 1, 1973

By Joseph W. Mussey

Bio-epigenetic sulphur deposits occur in Pecos, Reeves and Culberson Counties of far West Texas. Sulfate reducrng bacteria, utilizing hydrocarbons as energy, transformed gypsum into replacement limestone and hydrogen sulfide. Hydrogen sulfide, retained in the porosities of the replacement limestone, was subsequently oxidized by highly oxygenated groundwaters, and native sulphur precipitated. West Texas sulphur was first recognized at surface exposures by William P. Blake, a geologist attached to the Captain Pope Military/ Scientific Expedition of 1854. Attempts were made in the early 1900's to mine these sulphur vent exposures by a retort method, but the ventures met with little success. In 1967, Duval discovered a large sulphur deposit near some of the old sulphur works in Culberson County. Duval also extended a small sulphur deposit in Pecos County. The Frasch process, developed for producing sulphur from Gulf Coast salt domes, proved successful in West Texas type sulphur deposits also. However, modifications of the process were necessary to provide economical and efficient sulphur recovery from the varied ore modes. West Texas conditions and logistics require the ultimate in productivity to be competitive in the domestic and foreign sulphur markets. Several companies, in addition to Duval, are producing or have produced sulphur in West Texas. As of the first of June 1984, a total of 29.4 million long tons of sulphur had been produced west of the Pecos -aver. Duval produced more than 88 percent of that total.

Jan 1, 1984

By Thomas E. Newman

This paper is a case study using new laser-terrain-mapping technology by EagleScan, Inc., for creating topographic maps. Holnam, Inc., has used this technology to create maps and volumetric calculations of several mines in the United States. The information is superior to conventional methods through accuracy, manpower, time, and cost. Holnam, Inc., was the first cement manufacturer to use the Digital Airborne Topographic Imaging System (DATIS?). The technology uses the DATIS? to produce high-resolution terrain maps and volumetric assessments of any area. DATIS? is a mapping instrument that integrates (1) a Light Detection and Ranging (LIDAR) instrument to measure terrain elevation using laser light, (2) a large-format digital camera, (3) a relative position Global Positioning System (GPS) to measure aircraft position, and (4) an Inertial Measurement Unit (IMU) to measure aircraft attitude. The DATIS? can measure up to 220,000 elevation samples per mil. The system continually collects data on the aircraft's position and measures the time for each laser pulse transmission to return from the ground, giving each sample a GPS reference. The system can operate at night, in overcast sky, and during high-wind conditions and can measure terrain below vegetation cover, unlike standard aerial photography used for traditional surveying and mapping. Surveyed ground-control panels are no longer necessary with this new technology, and only one ground GPS base station located within 60 mi from the aircraft position is required. A computer elevation-point data file is created with the x, y, z coordinates of each laser elevation sample. With this file, CAD engineering programs can create topographic maps that rival products using conventional aerial mapping techniques. Volumetric measurements of stockpiles and pits are also available due to the high density of points collected from an area. This new technology radically changes the turnaround time for map users, giving a product in the format used by today's cartographers. The time line from flight to maps is measured in days instead of weeks.

Jan 1, 1999

By R. Tanaskovic

Unfavourable climatic conditions in stopes are of significant economic and social importance due to the following reasons: - Working effect is much lower leading to decreased output and work productivity disregarding implementation of mechanization. - Manpower operating capability decreases much faster under unsatisfactory climatic conditions. Under normal climatic conditions a workman would expend much less effort in line with a shorter effective time for the achievement of identical production effects since the work would be more efficacious. The objective of study of problems and climatic conditions is to make the working environment in mines suitable for normal development of operations. Lowering of mining works to increasing depths and winning of a growing number of small orebodies over a broad area makes the problem of creating suitable climatic circumstances more complex. Mining costs are growing due to bench conditions in line with decreasing metal content in the ore, so frequently the investments required for creating favourable climatic conditions represent, in addition to the selection of mining technology, a very important parameter when making decisions regarding exploitation. As known, the basic factors affecting climatic operating conditions in mines-are: temperature, humidity and speed of air flow, implying that the climatic operating conditions are closely related to mine ventilation. Usually, the concept of unfavourable climatic operating conditions includes increased mine air temperature and humidity and low air flow velocity so that heat exchange between human organism and the working environment is impeded or reduced to minimum. Metal mines in Yugoslavia are characterized by the existence of a large number of active faces - stopes and horizons and lowering of mining operations to increasing depths, so that face ventilation solutions are more and more complex. Since its foundation (1961), our Institute is engaged in investigation of factors influencing climatic circumstances improvement of calculations for air distribution and distribution control in complex ventilation networks and study of problems related to ventilation of large volume and irregular configuration faces, as well as application of gained knowledge in our mines. The paper presents the knowledge and experience gained in the case of Lead and Zinc Mine "Trepca" - Stari Trg.

Jan 1, 1980

By Thomas F. Stinson

Energy-producing states see severance taxes as attractive sources of increased revenues for otherwise tight budgets. Consumers in energy-poor states, however, protest that current rates are excessive and have moved to obtain a reduction. The US Supreme Court heard two cases questioning such taxes during its 1981 term, and Congress, in each of its last two sessions, has seriously considered measures placing a ceiling on severance tax rates. Although discussions usually focus on coal severance taxes levied by Montana and Wyoming, ramifications of changes in national policy are much larger, potentially affecting mineral taxes in all states. Severance taxes yield substantial revenues in some states, as illustrated in the accompanying table. In fiscal 1980, Texas collected more than $1.5 billion from such taxes, while Louisiana, Alaska, and Oklahoma collected $525 million, $507 million, and $436 million, respectively. Oil and natural gas production were the major items taxed. While the table shows only the 10 states with the largest severance tax collections, a total of 17 states had severance tax receipts exceeding $10 million in 1980. The enormous increases in severance tax revenue between 1970 and 1980 can be seen from the table by comparing columns A and B. For the 10 states shown, revenues increased from $650 million to $3.8 billion during that period, due to a combination of higher prices, increased production, and new or increased taxes. In most states, increases in prices and production were more evident than higher tax rates. Although the revenue increase is impressive, it understates the extent of changes occurring during the past decade. Since tax collections are shown for fiscal 1980, the full impact of the decontrol of domestic oil prices is not evident. Also, taxes on natural gas reflect controlled prices. When full de-control of natural gas occurs, significantly higher revenues can be expected in gas-producing states, even if tax rates, production, and world prices remain constant. These increases in severance tax revenues, coupled with further increases expected to accompany natural gas decontrol, have produced fears that a substantial transfer of income is taking place from residents of energy-poor states to those living in energy-rich areas. Others worry that increased severance tax revenues will be used to substitute for a substantial portion of state taxes that would have otherwise been collected from firms and individuals. The resulting improvements in tax climate, it is thought, may encourage firms and workers to migrate to energy-producing states. While these issues are often portrayed as pitting energy have-nots against the haves, such is not entirely the case. Much of the original impetus for limits on coal taxes came from Texas residents, the state collecting the most severance tax revenue. One way of gaining perspective on these concerns is by examining severance taxes per capita and as a percent of state tax collections (see columns C and D in the table). When this is done, Alaska, where 1980 taxes on oil and gas production totaled more than $1300 per capita (and 35% of all state tax collections), stands out as a special case. There, the state was able to eliminate some individual taxes, place revenues in a permanent trust fund, and consider offering a rebate of some previous income

Jan 4, 1982

By R. V. Ramani

Control is a vital management function by which operations are brought into compliance with predetermined standards to achieve the goals of an enterprise. Events that are characterized by a low degree of expectation, avoidability, and intent necessarily have a low degree of control. Such events are difficult not only to predict but to control as well. Fortunately, very few industrial situations fall into that category of events. It is an axiom of control technology that in order to control, one must first measure; further to measure, one must know the characteristics of the subject (or environment) upon which the measurement must be made. Finally, if measurements are to be made reliably, the influences that affect the measurement must be known and, if possible, understood. The complete control cycle therefore consists of the following: (1) defining the objective, (2) planning to achieve the objective, (3) putting the plan into practice with appropriate instructions, (4) measuring variables or parameters of interest, (5) transmitting and transforming the measurements to analyze the system's status and to predict the future outcome, (6) comparing these with the defined objective, and (7) determining and taking corrective actions to bring the actual results closer to the objective. The management principle underlying the control cycle is the principle of management by exception. The application of the principle and the frequency with which corrective actions are taken vary according to the purposes of the review and control. For example, the control of a machine operation (e.g., truck on a haul road) may require adjustments and therefore data, analysis, and decisions, in intervals of seconds whereas the review for ore-grade control may take several hours. Reviews, on the other hand, for cost control may be done in intervals of weeks or months. In any case, three specific purposes of the control cycle are: (1) to correct the operation so that it follows the accepted plan closely, (2) to evaluate the operation and predict future outcomes in light of changes in the environment or of more experience, and (3) to review the objectives and modify these to be reasonable and realistic.

Jan 1, 1979

By J. van Oldenborgh

The world market for bunkers represents some 140 MT (1980) of marine fuel oil and distillates. This is equivalent to 23CMT of coal, a potential market for steam coal larger than the total seaborne trade of steam and metallurgical coal today, and an obvious area which could contribute savings in world oil consumption. Oil bunkers are lifted fairly evenly throughout the world, the main supplying regions being Western Europe, the Middle East, North and Central America and Japan (Figure 1). Not surprisingly, the main customers are the tankers representing about 50 percent of the world market - (95 percent of the Middle East Market) - dry bulkers represent some 30 percent and general cargo ships the rest.

Jan 1, 1982

By R. K. Singhal

This new tool can be used for the proper assessment of the potential economic wealth of any risky capital project. It does provide an unambiguous recommendation of the type "go or no go" to the decision-maker simply by comparing two different ratios profit/investment. One ratio determines the minimum value required to at least break-even while the other measures a probable value based on the asymptotic theory of statistical extremes (weakest link concept). Its application is briefly illustrated by means of an underground gold mine project, an oil sands mine project and a poly-metallic open pit project.

Jan 1, 1993

By William H. Peterson

How is the Government's oil import control program doing? In July 1954 Mr, Eisenhower established the Cabinet Committee on Energy Supplies and Resources Policy. On July 29, 1957, the Administration imposed "voluntary" company oil import quotas on American oil importers to maintain "a healthy domestic (oil) production industry" and safeguard "national security." On March 10, 1959 the President by proclamation made the voluntary program mandatory. But study of the program in practice shows that it is not working out as expected and-that there is some doubt that its aims and other related Administration purposes are being achieved. Take the Administration's anti-inflation policy. To be sure, the President apparently recognized in his March 10th proclamation that in restricting cheap imported oil in favor of more expensive-domestic oil he was making the inflation fight that much harder, for he called for Government surveillance of domestic oil prices to prevent them from getting out of hard, And indeed while domestic crude oil prices have not risen appreciably during 1959 neither have they fallen appreciably (although there has been some price weakness in the past few weeks).

Jan 1, 1960

By Duane L. Whiting

The National Environmental Policy Act of 1969 (NAPA) provides guidance for federal agencies in making informed decisions. The Act has been used to determine the potential environmental impacts from mining and other natural resource operations, primarily in the Western USA. To accomplish the purpose of the Act, a process for developing environmental documents was established. The documents (EA/EISs) evaluate environmental impacts and are produced by federal agencies through public participation and cooperating agency review. Effective interactions and up front coordination between agencies and industry is required. An abbreviated history of environmental protection in the USA leading to NEPA, the driving regulation, objectives, provisions and limitations of the Act, and select mining related NEPA projects III the Western U.S. are discussed in this paper.

Jan 1, 1998

By E. H. Cho

Pittsburgh #8 coal cleaned by the conventional froth flotation was oxidized in a 2-liter Parr Stirred Top Bench Reactor. The oxidation time was varied up to 5 hours; the temperature, from 150 to 225°C, the oxygen pressure, from 15 to 500 psi; and coal dosage, from 15 to 60 grams in 600 ml of distilled water. The oxidation of coal was evaluated by measuring total acidic group formed on the coal surface as well as by measuring the adsorption of calcium ion from a solution under standard conditions. It was found that the oxidation increased with increasing oxygen pressure without much leveling-off effect. However, the oxidation of coal increased sharply from 150°C to 175°C and then tended to level off above 175°C. The adsorption of calcium was reached more than 3% on the coal oxidized under favorable conditions. The adsorption of calcium on coal increased sharply with increasing equilibrium pH. The BTU loss was sensitive to oxidation temperature. This study concludes that the optimum oxidation of coal should be conducted at high oxygen pressures around (e.g. 500 psi) 170°C for 3 hours. This study also concludes that the oxidation in an autoclave is far superior to that in a fluidized bed in terms of calcium adsorption, BTU loss and reaction time.

Jan 1, 1994

By A. Pomianowski

A spectrophotometric study of xanthate solutions alone and their mixtures with equimolar amounts of alkyl trimethyl ammonium bromide (CnTAB) has established the additivity of ultraviolet spectra (190 - 400 my) for potassium ethyl xanthate (KEtX) and C12TAB. No obvious effect of C12TAB addition on the decomposition rate of KEtX was observed. The kinetics of collector abstraction by copper, nickel and sphalerite powders were studied in 10-5 - 10-3M solutions of KEtX alone and in equimolar mixtures of KEtX and C12TAB. Presence of C12TAB caused a 2 - 3 fold increase in the amounts of xanthate (equivalent to many monolayers) abstracted by copper and, nickel powders but had no effect on the abstraction of xanthate by unactivated sphalerite. The adsorption of C12TAB itself from the mixed solutions was very low, at most ore monolayer only, and was not influenced by the nature of the solid powder used. The results are interpreted in terms of molecular associations and synergistic action of xanthates and quaternary amines.

Jan 1, 1963

By Gregory M. Rumbaugh, Todd Kostecki, Christopher Mark

From 2015 to 2021, five massive pillar collapses occurred at four underground stone mines in the eastern United States. These events resulted in powerful airblasts that damaged mine infrastructure and mobile equipment, seriously injured miners, and disrupted underground travelways. Each of these pillar collapses propagated through the overlying strata, causing a subsidence basin on the surface. Pillar collapses are particularly hazardous for miners because they can occur with little warning and can affect miners that are far from the pillar collapse area. The following case studies show that certain factors may increase the likelihood of a pillar collapse. For instance, each of the five events involved the collapse of at least twelve benched pillars with width-to-height ratios (w/h) of 0.8 or less. This study elaborates on

By J. R. Mackie

Reserve Mining Company, the first large-scale taconite pellet producer in the United States, mines it's crude ore at the Peter Mitchell Mire located on the eastern end of the Mesabi Iron Range near Babbitt, MN. The ore is processed at Reserve's beneficiation plant on the north shore of lake Superior at Silver Bay, M. The mine and plant are linked by a 47 mile, double track, railroad which is owned and operated by Reserve. (see Fig 1). At rated capacity, the mine can produce 33 million It/yr of crude ore, 15 million It/yr of waste rock and 1.0 - 1.4 million yd3/yr of glacial till stripping. Haulage of all mined material is accomplished using trucks. Ore is transported by tractor-trailer side dump units which have capacitys ranging from 83 to 110 long tons. Waste rock and glacial till is transported in end dump units of 50 to 120 LT capacity. Loading is accomplished by 11/13 yd3 power shovels and 7/10 yd3 front-end loaders.

Jan 1, 1985

By Robert W. Bruhn

Ground movements associated with high extraction underground coal mining, such as pillar retreat and longwall, are sometimes large enough to disrupt the ground water regime as well as damage buildings and other surface structures. A U.S. Department of Energy/Bureau of Mines- sponsored subsidence study currently underway at Kitt Energy Corporation's Kitt No. 1 Mine near Philippi (Barbour County), West Virginia has provided an opportunity to monitor the ground water response above a mine panel during both developmental and pillar retreat mining. The initial findings concerning ground water effects presented in this paper indicate that total extraction mining produced significant water level declines in deep-lying strata but had little effect on water bevels at shallower depths.

Jan 1, 1985

By R. K. Singhal

In an underground coal mining environment, a frictional ignition may be defined as the ignition of an explosive air/ methane/coal dust mixture by mining machinery. As the use of power loading equipment has become more widespread, frictional ignition incidents have increased. There have been many fatalities and injuries from this cause including the death of eleven miners in Sydney coalfield of Nova Scotia, Canada in 1979. This paper reports on the findings of a preliminary study carried out under the auspices of the Coal Research Laboratories, Department of Energy, Mines and Resources Canada. The objective of this study has been to identify a Longwall face cutting system that is inherently safer than the conventional shearer loaders used in Nova Scotia.

Jan 1, 1985

By R. R. Beebe

Marcona Corporation produces about 3.5 million long tons of iron ore pellets annually on its two travelling grate pelletizing machines at San Nicolas, Peru. During 1969, these pellets will be shipped to customers in four marketing areas--Japan, the United States, Europe, and South America. All of these sales are on the open market, and product quality is a major concern. Typical chemical, structural, and quality test results for Marcona pellets are given in Table 1. [ ]

Jan 1, 1969

By R. L. Clayton

The Bagdad district is 67 kilometers west of Prescott, Arizona, (Figure 1). The area north of the Old Dick and Bruce Mines was originally mapped by Anderson, Scholz and Strobell between 1943 and 1945, (1). The region is perhaps better known for the Bagdad porphyry copper deposit of tertiary age. However, 2 to 5 kilometers south of this deposit are several small massive sulfide occurrences in a eugeosynclinal Precambrian greenschist environment. More specifically, in. the Bridle formation of the Yavapai schist series. Three of these mines - Old Dick, Bruce and Copper Queen - were mined by Cyprus Mines Corporation between 1957 and 1977, and produced nearly 2mm tons of 3.6% copper and 12% zinc. These deposits occur at the interface between andesite and rhyolite and are stratiform in character. Certain structural and textural properties of the Bruce orebody suggest that remobilization of the massive sulfides occurred at some period during the metamorphic history of the area.

Jan 1, 1978

By James S. Browning

Mica mining in the United States is confined largely to pegmatites and schists in a few well-defined areas. The largest region extends from central Virginia southward through western North and South Carolina, northern Georgia, and east-central Alabama. 1, 2, 3 Whereas in western North Carolina these pegmatite dikes are weathered to only a shallow depth, they are deeply weathered in the Carolina Piedmont and in Georgia and Alabama. Particularly in Georgia and Alabama, mica is found in the decomposed slates and schists adjacent to the pegmatites, and in deeply weathered granites. Most flake mica is obtained as the major marketable product by crushing and milling pegmatites.4 To a lesser extent, mica is produced as a byproduct of feldspars and spodumene.6 Past research by the Bureau of Mines has developed two methods for mica flotation. One method utilizes acid-cationic flotation for recovery of mica." This method requires thorough desliming of the ore with consequent fine mica losses. The other method utilizes an alkaline-anionic-cationic process for recovering fine size mica from pegmatite ores after desliming sufficiently to remove clay materials but not so drastically as to remove the fine mica. 8, 9, 10, 11, 12, 13 The latter process has also been successfully applied to a micaceous schist ore from California.14 This report summarizes the results of these research studies. Both of the flotation processes developed by the Bureau of Mines have been adopted by the mica industry and are being commercially utilized separately and in combination for flotation of mica from weathered pegmatite ores.

Jan 1, 1969