Search Documents

By Matthew Wilcock, Kenichi Soga, Peter Wright

"This paper discusses how an existing grey cast iron segmental tunnel lining responds to construction of a new SCL tunnel transversely beneath with zero clearance; how the damage assessment for the existing tunnel was conducted for impact of longitudinal movement; how the tunnel is subsequently instrumented to observe both movement and stress manifestation at its longitudinal connections and how the results from the instruments compare with the prediction. An assessment of neutral axis of the tunnel in longitudinal flexure is also explored using interpolated horizontal displacement data from a conventional monitoring system. INTRODUCTION The Royal Mail Tunnel (RMT) (formely Post Office Tunnel or ‘Mailrail’) was constructed using semi-mechanised deep level construction techniques from 1914 and 1917 (Lee 1938). Commencing full commercial operation in 1926, the system was until 2003; conveying parcels the 6.5 miles between seven sorting offices in the center of London, and linking the system with main line rail stations, Paddington and Liverpool Street (The British Postal Museum & Archive 2013). A single tunnel of 2.74m internal diameter facilitated a bi-directional twin narrow-gauge (~611mm gauge) railway road system for electric driverless operation. The tunnel lining is segmental grey cast iron (grade 10) made up of six flanged segments and a smaller flanged key segment; constructed into a ring of width 508mm The external diameter of the tunnel is 2.971m. For further details of the tunnel lining and material properties are outlined by (Devriendt & Alhaddad 2014).London Underground Bond Street Station is a major station of the London Underground system in the very center of London; in its vicinity, the RMT runs west-east perpendicularly above the north south Jubilee Line tunnels. Historic survey record of the Jubilee Line’s (the then Fleet Line) construction in 1974 and its impact on the RMT case is documented in (Crossrail 1993): it is one of only a hand full of case-studies frequently cited when assessing the impact of new construction scenarios of this type; not least including the assessment of the same tunnel, at the same site some 40 years later, and the subject material for this paper: It noted significant vertical displacement of ~90mm to the RMT without noticeable serviceability or operational impediment."

Jan 1, 2016

By S. C. Tadolini

The use of resin-grouted cable supports to control large ground movements in several types of underground mines has increased substantially since being introduced in 1991. Cables offer several advantages over traditional support systems, having large support capacities coupled with the flexibility to be used in low openings. Cable slings have been designed to be installed on-cycle using no-spin technology or a two-piece unit that can be placed with hand-held drilling equipment. Additionally, yielding cable supports have been developed and are being used to control large amounts of movement in coal and evaporite deposits.

Jan 1, 1998

By Edwin H. McKee

Eruption of rhyolitic ash-flow tuffs in the area of the McDermitt (Cordero) caldera began about 17.4 m.y. ago and continued for about 1.5 m.y. During this period of silicic eruptions, a circular area about 30 km in diameter collapsed to form a caldera that subsequently filled with sedimentary and volcanic rocks. 3 A total of more than 200 km of silicic rocks was erupted from the volcano. The final phase of igneous activity, about 15.5 m.y. ago, included resurgent doming and intrusion in the central part of the caldera. Three to 4 m.y. later +I2 m.y. ago), hydrothermal solutions using the northern part of the caldera ring fractures as conduits deposited cinnabar, pyrite, alunite, and other minerals in tuffaceous lake beds and volcanic rocks accumulated within the caldera. The ore-forming solutions may have been a residuum from the silicic magma or connate water or ground water heated by the still-hot resurgent magma in the central part of the caldera. The source of the mercury has not been identified. Later oxidation of the sulfide minerals and redistribution of the supergene minerals corderoite, several mercury nitro-oxychlorides, marcasite, iron, and titanium oxides in the sedimentary rocks account for most of the newly discovered ore body at Cordero.

Jan 1, 1976

By M. S. Klima

A 25-mm diameter dense-medium cyclone was tested to investigate the effects of geometry and operating conditions on cyclone performance when processing -150 I'm coal. The emphasis was on examining those variables (e.g., flow rate and inlet velocity) which impact the separation kinetics (specifically the number of g's and the mean retention time) and the occurrence of apparent bypass. Apparent bypass, indicated by partition curve "tails", results from the short circuiting of the feed coal to one or both of the product streams and represents a loss and/or contamination of the clean coal. This paper presents the results for this series of tests.

Jan 1, 1993

By Douglas W. Barr

If some of you have been through the long hot summer in the southwest, you may find it refreshing to turn your thoughts to the wintertime problems of mineral processing in the northern climates. The purpose of this paper is to point out some of the ways in which heat is gained or lost in the tailing basin operation and the problems that can result if too much heat is lost.

Jan 1, 1980

By Paul R. Weber

Open-pit mines are constructed in materials characterized by the complete range of geologic materials from the most recent alluvial sediments to hard intact crystalline rock. The determination of stable slopes in recent alluvium is in the realm of soil mechanics, an established engineering discipline, well founded on theoretical development and years of substantiating experience. The analytical tools of the soils engineer are chiefly derived from continuum mechanics wherein load-deformation response is governed by mass properties of the substance. At the other end of the spectrum, slopes in hard unweathered rock can generally be analyzed in a straightforward manner by the methods of discontinuum mechanics wherein the properties and orientations of joints control the response of the material. This approach is exemplified by the classical work of Terzaghi (1962). In between these two extremes is a gray area of material types which are composed of stiff soil and incompetent rock. This area is of importance to the mining engineer, since a large portion of open-pit mines is excavated wholly or in part into incompetent rock. This paper describes an approach to pit slope design in incompetent rock in which the material behaves essentially as a continuum. A wide range of geologic materials from stiff soil to poorly indurated sandstone and shale to crushed or weathered crystalline rock appear to fit in this category. These materials all possess certain mechanical properties which must be accounted for in a realistic assessment of slope stability. These properties include nonlinearity, s tress -dependency, and inelasticity. Further considerations involve residual stresses and time-dependent seepage pressures where groundwa.ter is present.

Jan 1, 1971

By . A. Drouin, J. -M. Lalancette, D. Lemieux, C. Chouinard

"A gold bearing pyrite concentrate was treated at the demonstration scale (15 t/d) for the extraction of gold using a cyanide-free process. The pyrite was depressed in the flotation circuit in order to promote the flotation of copper and to achieve a sufficient copper grade to meet the copper smelter criteria. However, the recoveries of copper were 80% and only about 50% for the gold was found in the copper concentrate. The balance of the gold (50%) and copper (20%) contained in the pyrite concentrate as a reject from an overall flotation circuit. The gold grade in the pyrite concentrate is 5.40 g Au/t and copper about 0.77%. About 170 tons of pyrite concentrate were processed in the DST demonstration plant. The concentrate was first oxidized using a fluid bed to produce a calcine. Copper was then extracted as copper sulphate using diluted sulphuric acid. The residual solid was submitted to the DST chlorination process for gold extraction. Thereafter, the gold was recovered from the pregnant brine by precipitation over silica using DST proprietary process. The maximum gold recovery by chlorination was 90%. The average gold recovery by cyanidation of these calcines was 71%. INTRODUCTION Dundee Sustainable Technologies (“DST”) has developed a chlorination process as an alternative to the conventional cyanidation process for the extraction of precious metals from ores or concentrates. The technology offers viable and efficient gold recoveries and the ability to handle refractory ores and contaminated material (As, Hg, etc..). The process was successfully demonstrated on hundreds of samples provided by various mines, exploration and development projects and has evolved from laboratory experiment to demonstration at an industrial scale. DST’s chlorination process operates in a closed loop circuit, which implies that no liquid effluents are generated. The chemistry and process design allows precious metal deposits containing base metals to be treated viably. The tailings from the process are inert and non-toxic, sulphide depleted and thus non-acid generating. The efficiency of the process has demonstrated excellent gold recoveries within a fraction of the time needed for cyanidation to obtain similar results. The company completed in 2015 the construction of the first industrial demonstration plant operating with the DST technology. The plant has a capacity of 15 tons per day of mineral concentrate, and the ability to extract gold and silver utilizing DST chlorination technology. DST has tested its chlorination technology at demonstration scale on the refractory pyrite concentrate containing 5.40 g Au/t and 0.8 %copper. This auriferous pyrite concentrate, was by-product of copper concentrate respecting the copper smelter norms, is produced in a country where cyanide is prohibited and refractory to cyanidation. The pyrite concentrate was initially processed successfully (gold recoveries: > 90%) by the DST technology at laboratory (2011: 20 kg) and pilot (2014: 5 tons) scales to extract gold. About 170 tons of this pyrite concentrate were processed in the DST demonstration plant located in Thetford Mines."

Jan 1, 2017

By James M. Griffin

It was not many years ago that people would have argued that a coal session did not belong at an International Mining Convention. Historically, steam coal has always been used domestically due to its natural geographic diversity and high transportation expense. Times have changed. With the help of Opec, steam coal has gone international. As opposed to metallurgical coal, whose trade routes have a long history, whose supply sources are more limited and whose market growth is seen by most to be relatively flat, steam coal export forecasts are calling for more than a doubling by 1990 and a quadrupling by the year 2000. Suddenly, one must be familiar with coal mining on a global basis in order to predict which regions will be able to fill these markets.

Jan 1, 1982

By F. Calizaya

This study summarizes the results of various numerical and laboratory experiments per-formed to study the effect of airflow recirculation on gas concentration. The numerical exercises were carried out on a simulated mine ventilation net-work. The laboratory experiments were conducted at the Mackay School of Mines' airflow monitoring system in Reno, Nevada. In both cases, the airflow was recirculated through the system by means of a main fan and a set of booster fans. The booster fans were positioned to produce two types of recirculation: In line and Cross-cut. For each type, various recirculation conditions were generated by changing the booster fan pressure. During each test, the gas emission rate at the simulated working face was kept constant. The study illustrates the conditions under which controlled airflow recirculation may be used to solve a district ventilation problem.

Jan 1, 1991

By S. C. Suboleski

In a high risk venture such as mining where capital is committed and contracts are signed on the minimum of information, decisions are based primarily on production forecasts derived through consideration of such factors as management-labor relations, mining practice, variations in physical conditions and the equipment applied. Among these factors, the physical conditions offer the least opportunity for control and, due to the wide range of mining conditions that may be experienced, little effort has been made to develop objective methods for measuring their effects on mine out- put. The aim of this paper is to demonstrate a method for assessing these relationships that can be applied under a wide range of conditions both in new mines and in working sections where there is a need to determine the impact of proposed operational modifications. psing empirical data from active underground mines, a mathematical model was developed to derive a set of regression equations for predicting production as a function of mining conditions

Jan 1, 1980

By G. X. Wang

The nonliving dried water hyacinth (E. crassipes (Mart.) Solms) roots were investigated for biosorption of cadmium and lead and other heavy metal ions in aqueous solutions. Dried water hyacinth roots, when suspended in solution, strongly and rapidly sorb several different metal ions. Factors such as reaction time, pH, initial concentration of metal ions, presence of other metal ions and biomass concentration were investigated. Metal ions, including Cd2+ and Pb2+, were bound to the root in a very pH-dependent manner, with the binding increasing after about pH 3. High levels of removal were obtained. The adsorption was shown to follow the generalized Langmuir adsorption equation. The relative affinity of the roots for lead is greater than for cadmium. The maximum sorptions of the roots were about 33 and 86 mg/g for cadmium and lead, respectively. Only 15-20 minutes were required for the process of uptake onto the biomass to occur. The batch sorption kinetics of the uptake of cadmium and lead can be described by an apparent first-order reversible reaction model. The roots could be regenerated after the metal ions were stripped. A solution of CaCl2 in acidic medium appeared to be the best eluant for desorbing the sequestered Cd and Pb completely at pH 3. The kinetics of the metal stripping process was quite rapid. Successful desorption of Cd and Pb from the biomass by acidic CaCl2 solutions revealed that the metal uptake phenomenon is reversible, implying physical sorption of Cd and Pb.

Jan 1, 1997

By Dan S. Nilsson

Small-scale mines are today expected to provide much of the increased production of metals, industnial minerals and coal this country demands in the future. But what is the size trend in the mining industry?

Jan 1, 1980

By A. Bhagwat, S. Tadolini

"Steel members of the ground support systems in underground mines are routinely exposed to corrosive environment that may range from acidic to alkaline. Corrosion of steel bolts leads to metal loss and thereby, reduction in strength and useful life. Protective coatings are commonly applied to the steel bolts to combat corrosion. However, coatings are expensive and often cumbersome in practical applications. Instead, Minova has developed an innovative technology based on sacrificial anodes. The anodes were designed from non-ferritic alloys that are inferior to steel on the Galvanic Series. This paper will present data from field testing to show significant benefit of the technology. Potential applications in current products will be discussed. INTRODUCTION Corrosion is a physical alteration of a steel material from electrochemical reaction with its environment that often results in reduction of the mechanical and physical properties of that material. Mine roof bolts, the subject of this investigation, are particularly susceptible to corrosion as they can be exposed in their working environment to ground water and air with high humidity. As other researchers have determined, corrosion increases markedly in sulfide ore bodies due to acid runoff. There are several types of corrosion that a rock bolt is likely to undergo when used for ground reinforcement in underground mines (Aziz et al., 2013). Of all the types of corrosion, pitting is particularly dangerous as it can remove capacity for the bolt to deform with subsequent strata movements. Sudden failure of a bolt is likely to occur when severe pitting corrosion is experienced. The type and nature of corrosion depend on the nature of the ground condition and bolt encapsulation. Generally, the type of corrosion and severity of the corrosion varies along the axis of bolt. Almost all of the mine roof bolts used in mines, with the exception of fiber reinforced polymers, are made from steel. The corrosion of iron is an electrochemical phenomenon with the overall equation:"

Jan 1, 2018

By D. G. Chedgy

This article presents a novel design, called the Climax High Capacity Processor (HCP), for pre-combustion cleaning of coal. This design is particularly suitable for the plant capacities of 400 -660 TPH. The HCP is different from the conventional designs with an equivalent throughput in three major aspects: 1) the use of one large capacity HM cyclone to separate coarse and intermediate raw coal in a single circuit; 2) the elimination of the conventional secondary magnetics recovery system by use of the high efficiency Climax magnetic separators; 3) the use of "single line" piping with a minimum requirement of ancillary devices. In comparison with conventional designs with similar capacity, the HCP plant costs much less in capital investment, operation and maintenance.

Jan 1, 1997

By William A. Vogely, Robert T. Deacon, Walter J. Mead

Oil and gas together are the most important energy sources consumed in the United States. In 1983, 67% of total energy consumption was represented by these two resources (43% was oil and 25% natural gas), while coal accounted for only 23% of U.S. energy use. All other sources (hydroelectric, nuclear, geothermal, wood and other waste products) accounted for only 10% (U.S. Department of Energy, 1983, p. 1). In this chapter we address the issue of regulation in the oil and natural gas sectors of the U.S. energy industry. In addition, we analyze the cartel characteristics of the Organization of Petroleum Exporting Countries (OPEC). If OPEC is an effective cartel, then U.S. oil as well as substitute energy prices, production, and consumption will be affected by cartel action. Further, as the nation learned in the 1970s, major changes in oil prices produced major disturbances in other sectors of the U.S. and world economies. Consequently, it is important to determine whether the roughly ten-fold increase in nominal prices that occurred in the 1970s was the result of cartel action, the result of normal economic forces adjusting to the fact that the world was running out of cheap oil, or some combination of the two. Furthermore, the presence of OPEC- associated oil price increases is related to regulations that were imposed on the energy sector during the decade of the 70s. THE RATIONALE FOR GOVERNMENT INTERVENTION Economists have traditionally judged the state of an economy to be efficient if it is impossible to improve the welfare of any one member of society without harming someone else. Any economy that satisfies this condition is said to be Pareto efficient, after the Italian economist Vilfredo Pareto who first gave rigorous attention to such questions (see Chapter 4.10). It is easy to see why an economy that fails to satisfy this condition could not be efficient; by definition, it would be possible to alter the allocation of resources in a way that improves everyone's welfare.' Much of the appeal of this weak efficiency criterion is that it avoids comparisons of levels of well being among different individuals. The cost of such generality, however, is that in any given economic system a wide array of different Pareto efficient states will typically be attainable. In the simple Robinson Cursoe economy of the undergraduate textbook, for example, efficiency could just as easily be attained in the case where most of the island's resources are owned by Friday as in the case where they are under Crusoe's control. However, the distribution of welfare among the two inhabitants would obviously be quite different in the two situations. Such equity issues cannot be settled on objective or scientific grounds. To decide which distribution of welfare is socially "best" an explicit value judgment is needed. It is useful to keep in mind the preceding distinction between efficiency and equity issues when analyzing the role of government in a market economy. Decentralized market processes will not necessarily result in a distribution of welfare that society considers just. For this reason a potential role for government lies in the redistribution of income among individuals. In some circumstances, however, market pro-

Jan 1, 1985

By Zhe Wang, Tichang Sun, Yongqiang Zhao, Zhengyao Li

Coal-based reduction followed by magnetic separation is a promising technology for processing refractory iron ores. Analysis of the size distribution of metallic iron particles is an effective approach for exploring the mechanisms of coal-based reduction. As metallic iron particles exhibit very complex shapes compared with nature ores, approaches for measuring and characterising metallic iron particles still remain unclear. In this study, the size of metallic iron particles was measured and characterised using manual point-counting by optical microscopy technics and image analysis. The effects of CaF2 as an additive on behaviour of the particle size distribution (i.e. mean size and cumulative frequency distribution) were also determined. Results indicate that CaF2 had a significant effect on the growth of metallic iron particles. When the CaF2 dosage increased from 0 to 8%, the mean size according to the area method increased from 9.03 to 16.28 μm, while the promotion effect gradually weakened and generated many fine metallic iron particles when the CaF2 dosage exceeded 8%. An increase in CaF2 dosage also led to cumulative distribution curves gradually shifting to the right mainly because F− can break the crystal structure of each phase during the carbothermic reduction of titanomagnetite and reduce the stability of the lattice structure, thus reducing the melting point and accelerating the growth of metallic iron grains. Compared to different measuring methods, the area method is a more suitable approach for measuring and characterising the size of metallic iron particles.

Sep 18, 2020

By Dennis C. Martin

Assessment of the potential for mining induced subsidence and determination of ultimate design requirements for a mining operation should be based on a number of assessment approaches. Although the rock mechanics engineer has a variety of limit equilibrium and numerical modeling tools available for assessment and prediction of subsidence effects, empirical approaches based on precedent experience provide a powerful tool for calibration/verification of analytical models and prediction of subsidence. Three separate analyses approaches have been applied to the assessment of potential subsidence for a proposed block caving mine in eastern Canada. The investigations have included an assessment of documented historical information from previous block cave mining at the site, deterministic analyses using limit equilibrium approaches to assess kinematically possible failure mechanisms, and three-dimensional numerical modeling techniques. Analyses results have been used and compared with precedent experience and documentation of subsidence behavior from previous mining to optimize the subsidence predictions for the proposed mine.

Jan 1, 1998

By Jagannath Pal, Ammasi Ayyandurai

Hematite ore pellets require a much higher induration temperature than magnetite ore pellets because no exothermic heat is generated due to oxidation inside during induration-like magnetite pellets. Carbon is used as in situ heat source in hematite ore pellets which can reduce temperature requirement in the induration strand and hence decreases energy consumption. Many investigators have reported that a 0.8–1.25% addition of carbon in hematite pellets can improve the pellet properties also. However, to investigate the exact role of carbon in hematite pellets, its reaction mechanisms and kinetics study are required which have not been done so far. Therefore, the reaction mechanism and its kinetics have been studied in this investigation. It has been found that carbon reaction happens in pellets from the surface towards the center in a topochemical manner which is controlled by pore diffusion of gas, and its activation energy is around 52 k J mol− 1. It is also found that apart from in situ heat, carbon in hematite pellets enhances diffusion bonding which improves pellet properties. This study ascertains the exact role of carbon in hematite pellets which may help operators to use carbon effectively to reduce energy consumption and improve pellet properties.

Nov 6, 2022

By A. W. Khair

This paper deals with the evaluation of the interaction between rock and the cutting tool, and with methods for determination of workability, and abrasivity of rock. A description of instrumentation is included along with research on the wearing process of bit tips and pick consumption. Analyses of bit rotation, evaluation of cutting, normal forces and energy consumption is presented. Finally influence of the basic water jet parameters and water jet assistance on the cutting process of hard and abrasive sandstone is discussed.

Jan 1, 1995

By A. Vien

A major thrust in Industrial automation over the past few years has been the exploration and incorporation of higher level (supervisory and optimizing) control strategies aimed at more fully exploiting the existing control system infrastructure. There is little doubt that this is worthwhile pursuit, however, one must not lose sight of the maintenance and development requirements of the basic control system. Statistics on loop performance indicate that this too is an area of considerable potential. In this paper the authors look at some of the less elegant, but arguably equally important issues in mineral processing plant control. The focus is on controller structures, loop tuning, sampling, filtering, and some of the other principal components of the regulatory control foundations. In many cases significant improvements In control performance can be achieved by getting back to the basics.

Jan 1, 1998