Search Documents

The Bureau of Mines has studied 260 underground coal mine fires which occurred from 1970 through 1989. Every fire had the capacity to be hazardous to life and property, however upon closer examination some were found to be inherently more dangerous than others. Our research involved reviewing and recording specific information contained in published Mine Safety and Health Administration fire accident reports. The objective was to determine if degrees of hazard relative to fire source or location could be construed from information contained in the reports. We specifically looked at the propensity for fires to cause injuries and fatalities as well as the need to seal the area in order to extinguish the fire. Relative to all underground locations, this review found that fires occurring in main haulage-ways were most likely to cause injuries and fatalities as well as require sealing of at least the immediate area to extinguish.

Jan 1, 1993

By S. S. Xue

A study has been conducted to remove iron from sulfate solutions using Eichrom's Dipex® extractant, P,P?-di(2-ethylhexyl) methanediphosponic acid (H2DEH[MDP]). It is found that this extractant can effectively and selectively extract ferric ion from highly acidic solutions. Ninety-nine percent of the iron was extracted from a simulated feed solution in a single stage. The separation factor, Fe/Zn, was 10 6 Over 90% of the iron in a loaded organic can be recovered in an aqueous solution by reductive stripping. This paper presents the experimental results. A new process for iron removal using Dipex extractant is described and discussed.

Jan 1, 1999

By P. T. Bissert, L. Yan, M. D. Klein

"Federal regulations require that refuge alternatives (RAs) are located within 305-m (1000-ft) of the working face and spaced at one-hour travel distances in the outby area in underground coal mines in the event that miners cannot escape during a disaster. The Mine Safety and Health Administration mandates that RAs provide safe shelter and livable conditions for a minimum of 96 hours while maintaining the apparent temperature (AT) below 35°C (95°F). The National Institute for Occupational Safety and Health used a validated thermal simulation model to examine the mechanisms of heat loss from the RA to the ambient mine and the effect of mine strata composition on the final internal dry bulb temperature (DBT) for mobile tent-type RAs. The results of these studies show that most of the heat loss from the RA to the ambient mine is due to radiation (51%) and conduction (31%). Three mine width/height configurations and three mine strata compositions were examined. The final DBT inside the RA after 96 hours varied less than 1°C (1.8°F) for the three mine width/height configurations and less than 2°C (3.6°F) for the three mine strata compositions. INTRODUCTION Following a mine disaster, workers will try to escape the mine. If their escape is futile, they can take shelter in a refuge alternative (RA). In 2008, the Mine Safety and Health Administration (MSHA) mandated RAs in mines to ensure that a safe and livable shelter is provided for a minimum of 96 hours, and that the apparent temperature (AT) does not exceed 35°C (95°F) inside the RA [1]. An ongoing concern with RAs is the potential to exceed this limit. The temperature rise inside an RA is due to the metabolic heat released by the occupants as well as heat released by the carbon dioxide scrubbing system. The National Institute for Occupational Safety and Health (NIOSH) tested a 10-person tent-type training unit RA in its Safety Research Coal Mine (SRCM) to investigate heat buildup in RAs. The 10-person capacity for the tested RA is based on 1.4 m2 (15 ft2) of floor space per miner. NIOSH-developed simulated miners, which are heat input devices that generate both sensible and latent heat, were used to represent the metabolic heat generation of an average miner (117 W) for testing in the SRCM. It was found that the number of occupants in an RA may need to be reduced based on the ambient mine temperature, which varies from mine to mine [2]. To further research temperature rise inside an RA, ThermoAnalytics, Inc. (TAI) was contracted by NIOSH to perform thermal simulations of the tested 10-person mobile tent-type RA. TAI developed a thermal model of the SRCM using RadTherm software, which incorporates a human thermal model (HTM) to represent the equivalent metabolic heat loss of a miner within the RA’s enclosed environment. The thermal model was previously validated by comparing simulation results with test results [3]. During a mine disaster in which miners would have to take shelter in an RA, mine ventilation may not be available. As such, mine ventilation was off for both the testing in the SRCM as well as in the simulations. This paper discusses the heat loss mechanisms and the effects of mine strata composition and mine width and height associated with a ten-person tent-type RA."

Jan 1, 2016

By P. Lan

Gold is often associated with arsenopyrite in many refractory gold ores. The selective recovery of arsenopyrite by flotation is therefore necessary in order to maximize the recovery of gold. However, the complexity of arsenopyrite flotation often makes it difficult to obtain a high recovery from real lean gold ore. This paper presents the results of arsenopyrite flotation by ultrasonic pretreatment in micro flotation experiments and bench scale flotation tests. The tests showed that pure arsenopyrite exhibited low natural floatability due to the oxidation on the mineral surface under ambient conditions. Using ultrasonic pretreatment, the oxidation film was ruptured and the floatability was enhanced greatly. The presence of Fe (III) was found to inhibit the flotation of arsenopyrite and this depression was also removed by the ultrasonic pretreatment. This result explained why the arsenopyrite in real ore is often difficult to float and how ultrasonic pretreatment can effectively improve the arsenopyrite flotation in real gold ores. Guanidine (GMM) was found to be a superior collector for arsenopyrite in acidic medium and xanthate in alkaline medium.

Jan 1, 1998

In the screening process, used to prepare particles for many applications, shape is known to have a significant effect. The degree of flakiness of construction aggregates has been considered particularly important. The objective of this research was to find values of operating parameters that optimize the separation of flaky from non-flaky particles by slotted screens. Thus an investigation was conducted to experimentally determine the influence of the particle size and thickness on the screening process. The Response surface method was employed for modelling and analysis of the data. Experiments employing a central composite design were performed on a pilot-scale, rectangular-aperture, vibrating screen to examine the effects of the screening variables the mass recovery of flaky and non-flaky particles to the oversize product. The SAS statistics package was used to fit a second-order model to each response and to analyze the fitted surface to determine the optimum levels. The optimization associated with a dual response system was then considered. The results of this study should provide a basis for optimizing screening conditions to obtain maximum recovery of non-flaky particles to the screen oversize while minimizing the recovery of flaky particles, which should be of interest to the aggregate industries.

Jan 1, 1999

By I. E. Odom

The rare magnesium-lithium clay mineral hectorite occurs at many places in the McDermitt caldera of Nevada-Oregon. Commercial development of several high purity deposits began in 1986. The hectorite was precipitated in a lake environment formed after collapse of the McDermitt caldera. Hectorite beds and lenses are associated with volcaniclastic sediments, limestones, dolomites, zeolites and locally sandy bentonites. The high purity deposits appear to be associated with hydrothermal areas. The hectorite consists of extremely small flake-shaped crystals, and Ca is the predominant exchangeable ion. Its color ranges from white to light green. Commercial uses developed to date include high brightness magnesium aluminum silicate products, organophilic clays, pulp retention, and ceramics. The MAS is used as a suspending agent, binder, stabilizer and thixotrope in aqueous solutions for cosmetics, household cleaners, pharmaceuticals and miscellaneous industrial applications. Organoclays are used in printing inks and paints.

Jan 1, 1992

By W. C. Hirt

Selective flocculation was used to produce superclean zinc concentrate with minimized silica contamination. Research was carried out on a flotation concentrate from the Jersey Miniere Zinc Company (JMZ) in Gordonsville, Tennessee. The material was first dispersed with sodium silicate and then causticized tapioca starch was used to selectively flocculate the sphalerite, leaving the silica in suspension. This technique has been applied commercially to iron ore beneficiation but has never been used for processing zinc. The feed material assayed 0.45% Si02. Use of 0.56 kg/tonne (1.13 lb/st) of sodium silicate and 0.070 kg/tonne (0.141 lb/st) of causticized tapioca starch resulted in 98.2% zinc recovery in a purified zinc concentrate assaying 66.0% Zn and 0.24% silica. The present target level for silica contamination in JMZ zinc concentrates is 0.3% Si02. This work has shown that selective flocculation offers a potential method for cleaning flotation concentrates, particularly where low silica products are required.

Jan 1, 1993

By Mark A. Koestel

Cobalt-sulfide mineralization can he found in potentially economic quantities where permeable, basal Cambrian formations "pinchout" against Precambrian pal eotopographi c highs. These environments are common around the Saint Francois Mountains of southeastern Missouri and they share many similarities with the geologic environments of Zambia and Zaire in South Africa. Exploration for this type of deposit involves test drilling targets identified by trend analysis from past drilling, geophysics, geochemistry and a comprehensisve study of regional geology and isopach maps. Innovative ideas, new exploration concepts and insoluble residue geochemical methods may provide the necessary "edge" needed to complement basic geologic understanding leading to ore discovery.

Jan 1, 1987

By Robert F. Kaufmann

INTRODUCTION In response to the Uranium Mill Tailings Radiation Control Act (Public Law 95-604, Section 114c), a report has been prepared by the U.S. Environmental Protection Agency (1980) which describes the potential health and environmental effects associated with uranium mine wastes. The author was responsible for the geology, hydrology and aqueous pathways analysis portions of the report. All potential sources of contaminants, solids, liquids, and airborne emissions, which might cause adverse impacts upon the environment or health of nearby populations were considered. Wastes at both active and inactive uranium mines (Hans and O'Connell, 1981) are described and assessed with respect to dose and health effects (Blanchard et al. 1981). The emphasis of this paper is on the liquid emissions and the aqueous pathway. Model uranium mines were developed for surface and underground mines. The model underground mine was placed in New Mexico while the model surface mine was in Wyoming. Development of a generic assessment was complicated due to the inherent variability of uranium mines. Also, most information available relates to uranium mills rather than to mines, or reported measurements were often influenced (biased) by wastes from a nearby mill and did not specifically reflect mine discharges. Consequently, the assessment presented is often based on conservatve (maximizing) assumptions which are identified as such, and which were based on knowledge from field investigations, available literature, and consultations inside and outside the U.S. Environmental Protection Agency. Maximum use was made of available data, supplemented with limited field studies in Colorado, Texas, New Mexico, and Wyoming. PREVIOUS INVESTIGATIONS Stream survey work in Colorado by the Water Pollution Control Commission and the U.S. Geological Survey (Moran, 1974; Wentz, 1974) mentioned a portion of the Uravan Mineral Belt and uranium mines therein, but the work did not emphasize uranium mines. Significant amounts of acidity and total trace metal concentrations were found in streams from 18 different mining areas. Dilution and chemical precipitation below mine drainages decreased concentration and increased the pH. Given enough time and distance, the streams recover naturally, but the accumulations of trace metals in the sediments increase. Field observations in 1971-72 of streams in most of Colorado indicated that approximately 724 km of streams in 25 different mining areas were adversely affected by mine drainage (Wentz, 1974). Discussions of the impacts of uranium mining on water quality or quantity are incidental in numerous impact statements and environmental reports prepared by industry and (or) the U.S. Nuclear Regulatory Commission as an integral part of licensing or relicensing uranium mills. Coverage on mining is usually minor as the principal focus is on milling impacts. The same is true for the recently prepared generic EIS on regulation of uranium milling (U.S. Nuclear Regulatory Commission, 1979). Radiochemical assessment of surface and groundwater in uranium mining districts of New Mexico is done by self-monitoring programs associated with NPDES permits. Also, radiochemical assessment studies have been funded by the New Mexico Environmental Improvement Division and U.S. Environmental Protection Agency. Unfortunately, there has been no concerted effort to prepare broad assessments of the cumulative impacts of mining and milling in areas of interest in Texas, New Mexico, and Wyoming. Critical review and synthesis of these types of data can produce rather useful information. For example, the publication "Water Quality Impacts of Uranium Mining and Milling Activities in the Grants Mineral Belt, New Mexico" (U.S. Environmental Protection Agency, 1975) addresses the groundwater and surface water changes as the result of extensive uranium mining and milling production in a relatively confined area. A more recent report by the Wyoming Department of Environmental Quality summarizes 16 years of aqueous radium and uranium data. The study reports significant amounts of radium-226 and uranium were present in surface water in the Shirley Basin as a result of inadequate mine water treatment (Harp, 1978). In Texas, surface water and groundwater monitoring conducted by industry, as well as by State and Federal agencies, reveals little or no change of chemical quality attributable to uranium mining and milling (Gesell, 1977; Kallus, 1976). This conclusion is based on 586 samples collected from 198 stations over a period of 39 years, but primarily from 1961 to 1975. The State monitoring program by several agencies is continuing, but data reporting and interpretation is lagging. One survey (Itin, 1975) showed that none of the mine water from the 10 lakes that were sampled was suitable for human use. The lakes were also unsuitable for irrigation due to mineralization of the water by sulfate, chloride, and TDS. One of the 10 was suitable for stock watering.

Jan 1, 1981

By C. D. Elifrits

The required reclamation of land disturbed by surface coal mining often results in the creation of some over steepened slopes which are prone to rapid erosion and sediment production. This natural activity on such slopes is not desirable nor allowed under current regulations. Experience has indicated that novel approaches must be devised to address the problem. Research conducted on field sites in Missouri has indicated that construction, during the reclamation and grading processes, of a man-made drainage system will control the erosion. The drainage system must replicate or exceed the natural system in terms of drainage density and channel frequency. Basic design considerations will be summarized in this paper and field results shown.

Jan 1, 1986

By G. Vallebuona

Currently, empirical models are used for predicting the hydrocyclone performance in terms of capacity, cut size (d50,c), water split and partition curve. These models, for example those of Lynch and Plitt, have been developed and checked for hydro cyclones with diameters larger than four inches. For smaller diameter hydrocyclones little empirical modelling has been done. This paper reports extended experimental research on small hydrocyclones. For these cyclones, the suitability of existing empirical models has been checked and their accuracy compared. Modifications of the existing models equations are proposed, improving their predictive capability for the small cyclones performance.

Jan 1, 1994

By Bruce E. Kester

The concurrent observation of the phenomena of alkali-aggregate reaction and development of efficient dust collection systems on rotary kilns made mandatory the process modifications to produce low alkali cements. Such low alkali cements as were available prior to these recent changes were either the rare result of low alkali raw materials, the loss of alkalies with dust loss from the kiln stack, or in some instances by the use of CaC12 in the kiln feed to increase volitalization of the alkalies and their subsequent loss or discard with the normal dust emission from the kiln. The relative slowly soluble nature of natural occurring alkali minerals in cement raw materials as compared to the very soluble nature of the alkali salts as present in cement kiln reaction products, either in clinker or in dust emission led to the development of the water leaching system. Two distinctly different problems of leaching are created by the two major systems of portland cement production, the wet and dry processes. The wet process is characterized by moderate dust loads and concentration of soluble forms of alkali in the dust. Further the return of the leached dust slurry does not materially change the characteristics of kiln feed on reintroduction and subsequently does not materially influence kiln operation. The dry process differs in high levels of dust emission and the presence in the collected dust of large amounts of unreacted kiln feed with its sparingly soluble alkali minerals. In the dry process reintroduction of leached dust slurry changes the dry process to what may be classed as a damp process. This change results in some decrease in kiln capacity and creates conditions of operation which are uncommon to either the wet or dry process.

Jan 1, 1963

By B. Yarar

Samples of coal from an adit in the Fording River District of British Columbia showed hydrophilic properties between depths of 0-24.5 meters and was naturally hydrphobic at higher depths. Laboratory experiments indicated that weathered samples (i.e., those mined at 0-24.5m) could be upgraded by froth flotation at pH<2 following slimes removal. The i.e.p. of samples varied regularly between pH=1.6-4.1, the weathered fractions being at the lower end of the pH scale. These values followed a pattern comparable with the flotation behavior of samples. A patchwise structure for coal surfaces determining the resultant disjoining pressure, which in turn determines flotation-non flotation relationships is postulated.

Jan 1, 1982

By M. G. Ayat

Coal degradation is the breakage of coal particles to finer sizes due to the continuous forces of attrition and gravity to which coal is subjected during mining, handling and preparation. The objective of this paper is to determine the extent of degradation that a coal slurry experiences when transported through pumps and pipelines. The examination of degradation results for a number of different coal slurries have indicated that the extent of breakage is dependent upon the physical properties of coal and the time span of circulation. These results have also indicated that certain size fractions of coal are more susceptible to breakage than others.

Jan 1, 1986

By H. Majima

In spite of the importance of the presence of pyrite in the flotation of sulphide ores, not many studies have been made from the electrochemical point of view. It is generally recognized that the oxidation of sulphide minerals is one of the most Important factors among those which affect the floatability of sulphide minerals. The concept that the presence of oxygen is essential to the flotation of sulphide minerals is supported by numerous experimental results (1). The presence of oxygen in sulphide minerals- aqueous solution systems would affect the electrochemical behaviour of sulphide minerals and subsequently lead to more complicated reactions on the surface of sulphides. Actually some of the phenomena observed in sulphide flotation are deemed to be more appropriately explained from the electrochemical point of view. The author and co-workers have studied extensively the electrode reactions of pyrite and its significance in sulphide flotation. The results have been partly published elsewhere (2-7). In this paper, the author discusses the electrochemical nature of pyrite, and the three different phenomena observed in pyrite flotation: (1) Xanthate¬dixanthogen system on pyrite, (2) Flotation of complex sulphide ores containing pyrite and (3) Depressive mechanisms of pyrite with cyanide. The phenomenon which has been known as an iron contamination effect due to steel grinding media on sulphide flotation is also explained from the electrochemical aspect. However, this problem is not directly concerned with pyrite, and it will be discussed elsewhere (8).

Jan 1, 1971

By V. F. Hollister

The Ivanhoe district, Elko Co., Nevada, is located in the northern part of the Carlin trend of epithermal gold-deposits, but it differs from most mines in the belt in that Ivanhoe epithermal gold ores are found in 14 m.y. old Tertiary volcanic rocks as well as in the better known Paleozoic sediments. Within the Ivanhoe district U.S. Steel (USX Corp.) discovered and partly developed an epithermal gold deposit largely hosted by Tertiary rocks that, with a 167-hole program, was found to contain an open ended probable reserve of 4.0 million tons of heap leachable open pit oxide ore averaging .042 opt Au. An additional 4.0 m.t. of open pit sulfide ore averaging .048 opt Au were also developed. The U.S. Steel orebody was a blind discovery in that it just barely outcropped, and it was found by drilling through a premineral but barren cover of altered Tertiary volcanic rocks.

Jan 1, 1988

By Thomas P. Meloy

Floating "fines" differs from floating "sands" because the fines have a much larger surface area compared to their mass. The forces that arise from this large specific surface the key to understanding the behavior and treatment of fine particles. Though the nature of these forces is not thoroughly understood, enough work has been done to give a qualitative picture of what is happening in a flotation cell. It is the purpose of this chapter to re-examine some of the more, recent theoretical work and-to indicate its importance.

Jan 1, 1962

By K. H. McDaniel

An interactive mine ventilation simulation software program (WIPPVENT) was developed at the Waste Isolation Pilot Plant (WIPP). The WIPP is a U.S. Department of Energy (DOE) research and development project located near Carlsbad, New Mexico. The facility is designed to provide a permanent, safe underground disposal of U.S. defense generated transuranic waste in bedded salt. In addition to its regular functions, the underground ventilation system is engineered to prevent the uncontrolled spread of radioactive materials in the unlikely event of a release. To enhance the operability system, Westinghouse Electric Corporation has developed an interactive mine ventilation simulation software program (WIPPVENT). While WIPPVENT includes most of the functions of the commercially available simulation program VNETPC (copyright © 1991 Mine Ventilation Services, Inc.), the user interface has been completely rewritten as a Windows ® application and screen graphics have been added. WIPPVENT is designed to interact with the WIPP ventilation monitoring systems through the site wide Central Monitoring System.

Jan 1, 1996

By Matthew J. DeMarco, Anthony T. Iannacchione

Coal bumps have presented serious mining problems in the U.S. throughout the 20th Century. Fatalities and injuries have resulted when these destructive events occur at the working face. Persistent bump problems can result in abandonment of large reserves or lead to premature mine closure. Through the years, a1ternative techniques such as artificial supports, extraction sequencing, destressing, pillar design changes and specific pi1lar retreat practices have been successful1y imp1emented to mitigate coal mine bumps. Several techniques have evolved for room-and-pi1lar operations that control the way the roof rock breaks, regulating the manner in which stresses are redistributed in the mined section. Special mine layouts employed in longwall mines have also proved to be successful in safely redistributing or containing excessive loadings. However, with ever increasing production rates, greater overburdens and new mining systems, the need to evolve even more effective bump control designs will continue to challenge the U.S. coal mine industry.

Jan 1, 1992

By Gordon M. Bell

Water has received little attention as a variable in flotation, even though it is a known fact that water hardness often has an adverse effect on purity and recovery, particularly on the flotation of non-metallic minerals. Because of this fact, process water used in some flotation plants is treated to reduce hardness to an acceptable level. In the laboratory, distilled water is usually used as the flotation medium in order to standardize conditions, whereas in flotation plants locally available water is used. At Rosiclare Works of Aluminum Company of America, Rosiclare, Illinois, where a vein-type of fluorspar deposit was being processed by flotation to make an acid-grade fluorspar concentrate until February of 1968 when the plant was closed, qualitative correlations had been observed between metallurgy and reagent consumption and the seasons of the year. The observed effects were thought to be due to seasonal variations in the quality of Ohio River water used as the flotation medium. Figure 1 shows the variations in total hardness and chloride contents of Ohio River water at Rosiclare for the period September 1964 through September 1967. During this period, the sulfate content varied from 85 to 245 ppm (as Na2SO4), the calcium from 90 to 160 ppm (as CaCO3) and the magnesium from 50 to 70 ppm (as CaCO3). The data in Figure 1 show that the total hardness and chloride contents are highest in the late summer and fall which are usually periods of low water and lowest in late winter and spring which are usually periods of high water.

Jan 1, 1970