Search Documents

By R. M. LaDouceur, C. A. Young, W. Nicholas

"Salicyl hydroxamic acid (SHA) adsorption on two rare earth oxides, lanthanum and yttrium, was studied. Adsorption at both surfaces occurred in two stages. Initially, the monovalent anionic collector appears to adsorb significantly and instantaneously in stage one and then becomes sluggish in stage two presumably because the initial stage passivated the surface. By comparison, adsorption during the sluggish second stage with lanthanum oxide did not stop but with yttrium oxide essentially stopped. Surface monolayer formation could not be observed in either of the two cases. Both stages appear to be due to multilayer formation of a surface precipitate as proven by Raman Spectroscopy for lanthanum oxide but inferred for yttrium oxide. Unlike the use of octyl hydroxamate as stated in the literature, increasing temperatures do not increase adsorption such that flotation of rare earths with SHA may be performed at room temperature leading to improved recoveries as well as significant energy savings. INTRODUCTION Rare Earth Elements (REEs) are comprised of the 15 lanthanides along with scandium and yttrium. The REEs with lower atomic numbers are relatively more abundant and are categorized as light REEs. On the contrary, the REEs with high atomic numbers are less abundant and referred to as heavy REEs. They are not really “rare” and, in fact, some of them are quite abundant in the Earth’s crust; it’s just that they “rarely” exist in concentrated deposits but rather are found dilute and practically everywhere. REEs share very similar physico-chemical properties but, because many of these properties are unique, they have gained enormous importance in recent times making several critical and strategic pending their use. For example, REEs have found extensive application in phosphor coatings, magnetics, and automobile cracking catalysts. Early technology was not advanced enough to produce commodity level production of the REEs and can be attributed to REE-bearing ores containing many rare earth minerals (REMs), not just one. In this regard, there are numerous REMs but bastnaesite, xenotime and monazite are considered to be the most common. Bastnaesite is a fluorocarbonate whereas the other two are phosphates. The separation of the individual REE-bearing minerals from the ores is not an easy task since they also exhibit very similar properties. Consequently, when flotation is used, it is done to produce bulk REM concentrates. For REM flotation, it is well established that octyl hydroxamate is more selective than fatty acid collectors (Pradip and Fuerstenau, 1983 and 1991). Liu et al. (2006) indicated that hydroxamates are the most common collectors for REMs. Pavez et al. (1996) studied the adsorption of oleic fatty acid and octyl hydroxamate on REM surfaces. Cui et al. (2012) studied the interaction of octyl hydroxamate with various REMs surfaces using various spectroscopic techniques such as XPS, FT-IR and Raman along with electron microscopy and concluded that such techniques offer ample information to establish adsorption mechanisms. Ren et al. (1997) studied napthalenic hydroxamic acid as a unique collector for flotation of REMs from bastnaesite ore and indicated that more selective collectors were needed. From these studies, it is clear that the quest of more selective collectors is essential but understanding how they adsorb at mineral surfaces is prerequisite to improving flotation performance."

Jan 1, 2016

By C. Newman

"Over the past decade, as conventional underground deposits have been depleted, mining operations have been forced to produce at greater depths and in more geologically and geometrically challenging conditions. As such, there has been a global increase in the application of cemented paste backfill (CPB) in tabular deposits utilizing open stope mining method with a delayed backfill placement. Despite the extensive use of CPB, many fundamental factors affecting the design of safe and economical fill structures are still not well understood. A critical issue in the design of backfilled stopes is the determination of stress states within the fill material itself as well as the surrounding rock mass. Analytical equations provide a means of quickly evaluating the effectiveness of a given design. However, in developing these equations large assumptions are implemented to simplify the design problem. It is important that one understands these simplifications as well as their effect on the overall design. This paper investigates common analytical equations utilized in the evaluation of single vertical backfilled stopes and their assumptions through comparisons to numerical modeling results. INTRODUCTION AND BACKGROUND As the mining industry continues to produce at greater depths and in more geometrically and geologically complex conditions, cemented paste backfill (CPB) has gained traction as a means of providing localized ground support in modern stope-and-fill mining operations. The application of CPB in stope-and-fill mining as a ground support material has led to the reduction of mine waste costs, while increasing both mine production and stability. In an attempt to achieve total extraction of the mining reserve, stope-and-fill mining operations often employ a primary-secondary excavation-support sequence (see Figure 1). In this practice, primary stopes are initially excavated and then backfilled in a two-stage pour; plug and final pours. During the first stage (plug), a CPB material with increased cementitious content is placed at the bottom of the stope providing a strong base from which to build a backfill structure as well as protect mine works from material breakthrough. Following placement, the backfill plug is allowed to cure to a given strength as designated by the mine design. Upon achieving the required cure strength, a less cementitious CPB material is used to backfill the remaining stope area. This is referred to as the final pour stage. With all primary stopes excavated and supported using backfill, the extraction of the secondary stopes commences as primary stopes are utilized as artificial pillars. While the application of CPB in a primary-secondary extraction-support mining sequence allows for a substantial increase in reserve recovery, it is imperative the mining personnel and planning engineers have a clear understanding of the material’s behavior and stress interaction with the surrounding rock mass to ensure the most efficient, cost-effective, and safe extraction of underground deposits."

Jan 1, 2018

By Keros Cartwright

Sanitary landfilling has become one of the most widely used methods of disposing of solid refuse. A principal concern of regulatory agencies and the public itself is that landfill operations do not degrade the physical environment, including water resources, and the ground-water reservoir in particular. Ground-water and engineering geology can guide landfill operations into suitable terranes or develop measures to compensate for any natural limitations at a particular site Experience and research in Illinois suggest four activities relating to landfill disposal that warrant attention by geologists and engineers: (1) Regional delineation of favorable and unfavorable hydrogeologic conditions to facilitate planning and preliminary screening of potential landfill sites. (2) Site evaluations, with considerations of geologic materials, topography, water levels, flow systems, and local occurrence and use of water resources. (3) Re- search on aspects of the hydrogeologic environment that control effects of, or are modified by, landfills. (4) Formulation of practices in the siting, construction, and operation of landfills that prevent, mitigate, or isolate deleterious effects. The first two activities are basically in the domain of earth science, requiring the application of fundamental concepts of geology and hydrology and conventional site-exploration methods. The third activity, research, requires contributions from geology as well as other disciplines, including soil physics, sanitary engineering, and chemistry. The fourth calls for policy decisions by regulatory agencies and elected officials, using the contributions of scientists and engineers.

Jan 1, 1970

By J. A. Organiscak

Two types of airflow splitting methods for improving longwall dust control were investigated by NIOSH's Pittsburgh Research Laboratory. These methods included a translucent mesh barrier and a staged spray barrier system to confine the shearer-generated dust to the coal extraction side of the long wall face while maintaining a cleaner split of airflow on the opposing worker walkway side of the longwall face. The translucent mesh barrier was shown to provide notable dust control effectiveness up to 60 m downstream of the shearer in both the laboratory experiments and a long wall field evaluation, provided the mesh barrier remains relatively parallel to the airflow. The staged spray barrier system showed marginal dust control effectiveness in the laboratory and subsequently was not field tested.

Jan 1, 1999

By A. Bergmann

Location The Meggen Mine and the concentrator plant of the "Sachtleben Bergbau G.m.b.H." are located in the southern part of the Ruhr-district of the Federal Republic of Germany. The mine has been in operation for more than 100 years, but the concentrator described in this paper was built in 1962 and started up in January 1963. Goelogy and Mining The Meggen ore-body is of sedimentary origin and occurs in a zone of limestones, graywacke and shales of Devonion age. The average thickness of the deposit is 3 meters and, due to an intense folding of the area, the mineralized zone dips very steeply at 800 toward the north. The ore consists of 85 percent of sulfides and 15 percent gangue that mainly contains silicates from the host rocks. The principal ore minerals are pyrite (67 percent), sphalerite (16 percent) and galena (2 percent) with minor amounts of marcasite and only traces of chalcopyrite. As shown in Fig. 1, the sphalerite and galena are very finely disseminated in the massive pyrite of the Meggen ore, and a very fine grinding combined with a special flotation technique are required to liberate the valuable sulfides and to produce separate concentrates of lead, zinc and pyrite. Mining is performed by the sub-level stoping method and employs trackless equipment. Present operations provide ore from the 600 meter level. Annual ore production is 870,000 metric tons.

Jan 1, 1972

By K. Sasaki, W. Astuti, N. Okibe, T. Hirajima

"The kinetics of leaching of a saprolitic ore from Indonesia by citric acid solution under atmospheric pressure was investigated. An examination of the effects of leaching temperature, citric acid concentration, pulp density and ore particle size on the dissolution rate of nickel found that they all had significant influence on the rate. The highest nickel recovery (95.6 percent) was achieved under the leaching conditions of ore particle size of 212-355 microns, citric acid concentration of 1 M, leaching time of 15 days, pulp density of 20 weight/volume percent, leaching temperature of 40°C and shaker speed of 200 rpm. The shrinking core model was found to be appropriate for describing the leaching kinetics of this ore in citric acid solutions at atmospheric pressure. The experimental data were well interpreted by this model with rate of reaction controlled by diffusion through the solid product layer. Using the Arrhenius expression, the apparent activation energy for nickel dissolution was evaluated as 12.38 kJ/mol. Finally, on the basis of the shrinking core model, a proposed empirical kinetic model for the leaching of nickel from this Indonesian saprolitic ore was expressed as a mathematical model, which was verified as consistent with the observed experimental results.IntroductionIndonesia has some of the world’s largest nickel laterite reserves and was the largest producer of nickel – in the form of nickel lateritic ores – in the world in 2013 (Merchant Research and Consulting Ltd, 2014). However, only high-grade saprolites are processed in Indonesia using pyrometallurgical methods to produce ferronickel and nickel matte. Lower-grade saprolites and limonites are removed, becoming waste or overburden in mining site areas. Hydrometallurgical methods, involving either chemical leaching or bioleaching, are now seen as the most important technologies for treating nickel laterites in the future because of their advantage of not only extracting nickel and iron but also other valuable elements. In addition, hydrometallurgical methods consume less energy and have lower capital and operational costs. Although they are recognized to be more suited to limonites, some researchers have studied their use in the extraction of nickel and other metals from saprolites (Guo et al., 2009; Lu et al., 2013). Hydrometallurgical processes for the extraction of metals, especially nickel, promise to be meaningful alternatives to pyrometallurgical processes to primarily treat low-grade saprolites for which pyrometallurgical processing is not favorable"

Jan 1, 2015

By Zoheir Khademian, Gabriel S. Esterhuizen, Morgan Sears

Based on the 2010-2019 Mine Safety and Health Administration (MSHA) accident report database, 91% of reported ground control accident in the US longwall mines were caused by gateroad roof instability. This can be related to the significant changes in loading conditions that gateroads are subject to from the development to the longwall abutment loading phases, combined with the thinly bedded shale roof, found in many US longwall coal mines. One of the challenges in designing efficient support systems is to understand the roof instability mechanisms along with support-roof interactions under this complex loading condition. Field monitoring of roof displacement and stress changes coupled with detailed analyses using numerical models are well-documented techniques to study the causes of roof instabilities. However, traditional modeling techniques require additional calibration to simulate delamination and buckling of shale roof, one of the main roof instability mechanisms in longwall mines. One alternative modeling technique is the UDEC Bonded Block Method (BBM) where bedded roof and support interactions can be explicitly captured. This paper presents the development of a BBM model of a longwall entry at a 180 m depth of cover with a three-entry gateroad layout along with roof extensometer monitoring results. The models are validated against the monitoring data, showing the potential for BBM numerical models capturing the complex roof and support system interactions to assist with optimizing gateroad layouts and support systems.

By James S. Goff, Stephen J. Navin, Wesley W. Moulton

The White River Shale Oil Corporation (WRSOC), as agent for Phillips Petroleum Company, Sohio Shale Oil Company, and Sun Shale Oil Company, is developing a prototype oil shale facility on Federal Lease Tracts Ua and Ub, located in northeastern Utah and known as the White River Shale Project (WRSP). The Ralph M. Parsons Company (Parsons) has been retained as the design engineer/constructor for the project. This paper covers the successful pregrouting of the Bird's Nest Aquifer in conjunction with the sinking of a 9.2-m (30-ft)-diameter shaft and driving of a 3.89-m by 5.64-m (18.5-ft by 12.75-ft) decline. The Bird's Nest Aquifer derives its name from the ellipsidal solution cavities caused by leaching of random-size nacholite nodules. The sodium bicarbonate nodules occur as persistent bands within a matrix of siltstone and marlstone. The team, made up of the owner, engineer/contractor, and subcontractor successfully grouted the shaft down to an inflow of less than 0.06 lps (1 gmp) and the decline down to less than 0.12 lps (2 gpm) by injecting a total of 213.190 kg (470,000 lb) of Celtite Terraseal, 113,400 kg (250,000 lb) of limestone dust, and 41,730 kg (92,000 lb) of cement into the formation.

Jan 1, 1985

By W. M. Lewis

Product losses to tailings ponds have long been a source of frustration for the mining and utilities industries. The utilization -of the Lewis Econosizer to recover lost products has proven to be very cost effective through reduced acreage requirements, cleaning costs and increased production. The unit is successfully operating in coal, aggregates, industrial minerals, clay, fly ash, heavy minerals and many other ores. Utilizing an upward flow of slurry in a free settling environment, particles stratify within the unit according to settling velocities and are removed as sized products. Ultra fines or clarified water is removed off the top of the unit. The Econosizer requires no power and only minimal maintenance.

Jan 1, 1998

By G. T. Austin

Every year the United States consumes millions of dollars worth of abrasive materials as blasting media. Entrained in either a gas or liquid stream or propelled by paddles or wheels, they are directed onto the surface of another material to modify that surface. The modifications to impacted surfaces include cleaning, cutting, deburring, etching, finishing, and peening. Blasting media can be either organic or mineral abrasive materials. Information and data presented are for only a portion of the mineral abrasives, they are; fused aluminum oxide, coal slag, copper slag, garnet, metallic shot and grit, nickel slag, olivine, silica sand, silicon carbide, and staurolite.

Jan 1, 1994

By H. R. Bullis

Lupin is located on the shores of Contwoyto Lake at lat. 65° 48'N, Long. 111° 15'W and lies about 80 kilometers south of the Arctic Circle. Since start up in 1982 the mine has produced over 2.15 million ounces of gold from 6.66 million tonnes of ore grading 10.63 gm/tonne. Total remaining reserves at 1993 year end were 5.1 million tonnes at a grade of 9.11 gm/tonne (1.65 million ounces). This is sufficient for 7 -8 years at the present annual production rate of about 200,000 ounces. The Centre and West Zones of the deposit are open to depth. The deposit is in an Archean metaturbidite sequence of the Contwoyto Formation, which has been mapped as part of the Yellowknife Supergroup of supracrustal metasedimentary and metavolcanic rocks making up part of the Slave Geologic Province. These rocks have been subjected to regionar and contact metamorphism and to several phases of deformation. Six stages of Archean plutonism have been identified and all Archean rocks have been cut by Proterozoic diabase dyke swarms. Gold mineralization in the Lupin deposit is commonly fine grained and associated with pyrrhotite and arsenopyrite in amphibolitic banded iron formation. The gold-bearing portions of the host iron formations are characterized by the presence of multiple quartz veins and the pervasive replacement of grunerite by hornblende. In sparsely mineralized portions of the host iron formation, zoning of sulfides about quartz veins is clearly seen with the arsenopyrite halo being more restricted around the veins than the pyrrhotite halo. In well mineralized portions, quartz vein densities approach one vein per metre along strike. In these areas pyrrhotite distribution in the iron formation is more pervasive and the rock takes on the appearance of a banded sulphide rock.

Jan 1, 1995

By C. Clark, R. Pakalnis, B. Seymour, L. Martin, R. Jacksha, M. Stepan, M. Roworth, C. Caceres

The National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop safe practices for the use of shotcrete as ground support in underground mines, particularly mines operating in weak host rock. As part of this research, a rugged, portable direct tensile test system was developed for measuring shotcrete adhesion strength in underground mines. During the development of this test system, more than 185 direct tensile tests were conducted with a common, commercially available macro-synthetic fiber-reinforced shotcrete that was applied to concrete test panels using a dry mix process and machinery. The average bond strength of the shotcrete to the concrete substrate typically increased as a function of the shotcrete’s curing age, ranging from 0.44 MPa (64 psi) after one day of curing to 1.58 MPa (229 psi) after 90 days of curing. Adhesion strength increased markedly between one and three days of curing, reflecting a similar trend of increasing shotcrete tensile strength with curing time. This robust direct tensile test system can improve mine safety by providing a reliable means of measuring shotcrete adhesion strength and also supplying important information about the quality of the applied shotcrete and the competency of the underlying rock.

Jan 1, 2010

By John J. Stetler

The Companhia Vale do Rio Doce in Brazil operates one of the most extensive systems in the world for the mining, transportation, processing, pelletizing and shipping of high grade hematite iron ore and pellets. Current shipping of unbeneficiated, sized, high grade ore from its ports at Tubarão and Vitória is now at the rate of 17,500,000 metric tons annually. An increase in this annual rate is now under study. Using the technology and facilities of Lurgi (1) and Arthur G. McKee company CVRD undertook a program to process and pelletize two types of fines - "Blue Dust" and ?Itabira Fines?. Blue Dust is a high grade fine ore which was bypassed while mining the direct shipping ores and which, also, exists as a very large ore body called the Conceição Mine. Itabira Fines is a lower grade of fine ore which is comprised of in-situ fines and, also fines which are generated in sizing the direct shipping ores for a rigid specification market.

Jan 1, 1970

By Edward C. Dowling

Froth flotation has been used industrially for many years to separate valuable minerals from their associated gangue constituents. Notwithstanding the significance of this process to the mineral industry, many of the engineering tools needed for the evaluation of the flotation process are still in a developmental stage. Traditionally, the evaluation of a flotation test on both the laboratory and industrial scale has been based largely on a rougher recovery value achieved at a sufficiently long time to give a "final" or "equilibrium" recovery value. The assumption of a time equivalency for a given recovery value between various flotation tests or between laboratory tests and industrial operation underlies this method of evaluation. Such an assumption implies that flotation is an "equilibrium engineering process" and that the time-rate recovery of material from the flotation cell is not affected by changes in the flotation system. It has been shown by Bushell (1) and by Klimpel (2) that the assumption of time equivalency between various flotation tests is unjustified. Consequently, better tools are needed for evaluating flotation test results, Because mathematical flotation models which incorporate both a recovery and a rate function can completely describe flotation time-recovery profiles, they can provide an excellent tool to evaluate flotation tests.

Jan 1, 1984

By R. R. Klimpel

This paper describes four new families of flotation products which are currently being introduced at the industrial level. A brief summary of the chemical basis behind each product family will be given. This is then followed by a selection of flotation examples which illustrate the more important use characteristics that have been observed to date. It is becoming more apparent with further testing that these four new product families can offer both technical and economic advantages to the industrial flotation process operator.

Jan 1, 1992

By E. L. Piper

Natural graphite has been known for many centuries, having first been reported as a distinct mineral form by Gessner in 1565. At that time, graphite was used extensively as pencil "lead" because of the ease with which it marks paper. It is a black, unctuous material found as flakes, lumps, or needles in scattered locations throughout the world. The less crystalline, or "amorphous", natural graphites are thought to have been formed from coal under conditions of high temperature and pressure. The more crystalline varieties, such as those mined in Ceylon, probably were precipitated from molten solutions or were pyrolyzed from gaseous carbon compounds. Recognition of the good thermal and electrical conductivity of graphite, together with its highly refractory nature, led to an increasing number of appli¬cations for this material. Clay and pitch bonded natural graphite has been used in crucibles, refractories, foundry facings, and other high-temperature appli¬cations. These forms constitute the most important current uses for natural graphite in the United States. Other products containing natural graphite include batteries, lubricants, pencils, brake linings, etc.

Jan 1, 1973

By Hun-Joon Sohn

Chemical metathesis and electrochemical reductive conversion of chalcopyrite in the presence of cupric ions were studied in sulfuric acid solutions for temperatures up to 90°C. The process results in the displacement of iron in the chalcopyrite lattice by copper ions with rejection of ferrous ions to the aqueous phase. The rate of reaction was found to be very slow, requiring subsieve-sized particles for extensive reaction to occur. The reaction was insensitive to copper ion concentration. Stirred ball milling of chalcopyrite introduces lattice strain. The reaction rate with strained particles was markedly higher than with annealed chalcopyrite. The reaction rate was found to be diffusion-limited, showing two distinct reaction stages corresponding to the formation of CuS (covellite) followed by Cu1.8S (digenite). The experimental activation energy for the first stage was 102 J (24.4 kcal) and the second stage 123 3 (29.4 -kcal) per mole. The rate-controlling process is diffusion of lattice ions, probably iron. The enhanced rate after milling is attributed to a recrystallization process which provides new paths for diffusion along dislocations and grain boundaries.

Jan 1, 1984

By James L. Hendrix

This paper is intended to give the reader an update on the work being done at the Mackay School of Mines about the fate of cyanide on precious metals mill tailings waste. During the last two years several tailings impoundments have been sampled and analyzed for total and free cyanides. From our sampling program we are beginning to learn valuable information concerning the fate of cyanides in precious metals mill wastes. Included in this paper is a detailed description of our sampling and analytical techniques. Also, some of the data obtained from five sites are given.

Jan 1, 1986

By E. J. Wade

My subject is gold price forecasting and monitoring as an important aspect of gold marketing. While I 'm specifically addressing gold, it is understandable that many other commodities could be readily substituted. Gold marketing must be studied as three distinct processes, and it is my intention to cover each of these processes in turn. First I?ll cover the process of gold price monitoring and forecasting in some detail. In order to select a method, or combination of methods, to be used to sell gold a determination of the future price profile is essential. The profitability of the sales effort will be determined, to a large extent, by how accurately the future price behavior of the gold market has been forecast.

Jan 1, 1985

By William R. Nash

Case histories of water problems in underground mine shafts and tunnels are outlined to illustrate varying degrees of sophistication in grouting techniques currently applied in such construction. The interception of water underground can be one of prior knowledge, i. e., the site investigation provides necessary data to plan a grouting program prior to construction start, or excavations may encounter "changed conditions" or unplanned water. The latter includes catastrophic inflows and emergency situations where the structural integrity of a building or concrete shaft lining are jeopardized. The presentation of this paper outlines some applications of grouting work in underground mine construction throughout the United States in a variety of geological provinces and for a variety of minerals.

Jan 1, 1984