Search Documents

Considerable attention has been given to the restoration of low-level radioactive (<1000 pCl/g) sites contaminated during the early years of the atomic energy program. Current clean-up activities which involve the relocation of contaminated soils to licensed disposal sites have been shown to be very costly due to the large volumes of soils which must be excavated, transported and stored. Recent characterization studies conducted at Virginia Tech suggest that the volume of soil requiring disposal can be greatly reduced using mineral processing techniques such as classification, density separation and froth flotation. This article discusses the application of these technologies for soil remediation and describes a conceptual flowsheet for treating soil samples from two contaminated sites.

Jan 1, 1997

By M. B. Haggerty, R. J. Sheets, F. Abbasy

To address coal refuse tailings storage needs for a mine operation in western Canada, a feasible solution was to convert excavated open pits into tailings cells. A slope stability investigation and design study were completed to determine the necessary width and slope geometry for in-situ native plugs as the impoundment embankment. The native plugs separate the previous open pit from the current active open pit. This configuration allows for the deposition of refuse tailings in the previous pit while allowing mining to safely continue “downstream” of the temporary impoundment. As mining progresses, each subsequent pit will be filled with refuse tailings; thereby, buttressing the upstream slope of the previous native plug. Although these cells are excavated, and the timeframe for downstream exposure is relatively limited, the native plugs are classified as dams and must be designed to meet applicable safety of dam standards since they impound water and tails above mining personnel in the subsequent open pit. The presentation and paper will discuss the investigation and analysis conducted to develop the geotechnical and hydrogeological design recommendations.

Mar 2, 2022

By Donald B. Buddecke

The large walking dragline has been the most commonly used overburden-stripping equipment in Texas lignite mines. These draglines, operating on the highwall side of the pit, can excavate to a depth of 45 m. Considerable overburden rehandling is required beyond 30 m and may reach 100 percent by 45m. As pit depth increases, dragline operation also becomes more complex, with two or three passes being necessary to make a cut 30 to 40 m wide. Multiseam operations also require extra passes. At pit depths greater than 45 m, the dragline must be operated also from a spoil bench. This can be difficult in the unstable alluvial deposits in which lignite occurs.

Jan 1, 1985

By S. McAlister

This paper outlines the development of the Falcon enhanced gravity separator. Design objectives included continuous operation with sharp separations, mechanical simplicity, minimization of process water demand, the ability to apply a centrifugal field up to 300G&apos;s, unit capacity in excess of 100 t/h within a footprint of 10 square meters, a capital cost below $US 4,000 per t/h capacity, and total operating costs of less than $US 0.40 per tonne. A parallel development has been inexpensive, effective, semi-continuous equipment for recovery of precious metals in the free metallic state. These objectives have been largely met. There are significant opportunities for the technology in many mineral processing applications.

Jan 1, 1998

By G. D. Hood

The U.S. Bureau of Mines investigated rapid froth flotation through more efficient bubble-particle collisions that improved the overall flotation kinetics. An in-line static mixer efficiently mixed the bubbles, water, and ore, selectively attaching these bubbles to the hydrophobic mineral&apos;s surface. As the mixture entered the flotation chamber, the hydrophobic mineral was already attached to the bubbles and was quickly floated away from the remaining ore pulp. The rapid flotation system was evaluated for beneficiation with a western porphyry copper ore containing 0.67 pct copper, and a phosphate-bearing amine flotation tailings sample containing 9.5 pct P2O5 in a quartz matrix. Over 88 pct of the copper was recovered from the ore in a rougher concentrate containing 5.9 pct copper at a rate 7 times faster than conventional flotation. Sixty percent of the quartz in the phosphate-bearing sample was floated at a rate 4 times faster than conventional flotation. The unfloated product retained 80 pct of the phosphate in a l6.9-pct P2O5 concentrate.

Jan 1, 1993

By T. Diering

Gemcom PCBCTM is a software package which has been developed over the last 22 years for the planning and scheduling of block cave mines. This paper presents an update of the various research and development activities done to PCBC recently. It also provides an overview of the current capabilities of the software including tools for both feasibility type studies as well as tools for operating mines. PCBC is used extensively by prospective and operating block cave mines and some of the recent applications are described.

Jan 1, 2010

By J. M. Wempen, M. K. McCarter

"Differential Interferometric Synthetic Aperture Radar (DInSAR) is a satellite-based remote sensing technique capable of measuring centimeter-level surface displacement with high spatial resolution over large areas. Regular monitoring of subsidence due to underground mine development is one potential application of DInSAR, and in this study, the application of DInSAR for subsidence monitoring is evaluated for two mining regions in the mountain west of the United States. In general, DInSAR has potential to identify the shape and extent of subsidence; in some cases, magnitudes and rates of subsidence can be defined. Importantly, the effectiveness of DInSAR for subsidence monitoring depends on the radar band (wavelength), the subsidence rate and the time between image acquisitions, and the topographic and vegetative surface characteristics. INTRODUCTION Differential Interferometric Synthetic Aperture Radar (DInSAR) is a satellite-based remote technique that can be used to measure small surface displacements. Under good conditions, centimeter-level displacements can be measured with subcentimeter accuracy (Buckley, 2000; Massonnet and Feigl, 1998). Additionally, DInSAR data have relatively high spatial and temporal resolutions. Pixels in Synthetic Aperture Radar (SAR) images can have a ground resolution as small as about 3 m, and images often include tens to hundreds of thousands of pixels and cover tens of kilometers. Regions are imaged regularly, and periods between images typically range from weeks to months. In DInSAR, phase measurements from two radar images acquired over the same region at different times are used to precisely measure relative distances (Rosen, 2014). Surface deformation, topography, and changes in the satellite position all contribute to differences in the length of the path that the radar wave travels in each image. SAR sensors use radar with relatively long wavelengths; L-band (24 cm wavelength), C-band (6 cm wavelength), and X-band (3 cm wavelength) radar are used most commonly. Because the wavelengths are long, small changes in the path length of the radar signal can be quantified by measuring the change in the phase of the radar signal between the images. In general, changes in the path length due to changes in the satellite position and topography are known or can be estimated, and centimeter-level changes in the path length due to deformation are measurable. This study evaluates the effectiveness of DInSAR for measuring subsidence in two mining regions in the mountain west of the United States. L-band data from the Advanced Land Observing Satellite (ALOS) and X-band data from the TerraSAR-X mission are evaluated. Imaging characteristics, including the radar band and the time between image acquisitions, are important for effective subsidence monitoring."

Jan 1, 2017

By A. Habibi

The FMC Westvaco Trona Mine is located near Green River, Wyoming and has an annual production of 4.5M tons. Trona is an evaporite mineral that is processed into several products, mostly soda ash. The underground mine has two active development panels and one longwall (LW) panel. The mining horizon is about 500m below surface and the surrounding strata liberates methane. Three surface-based, blowing fans provide ventilation air as a positive pressure system. The mine operates a 225m long LW face, built by Joy Mining Machinery. Headgate and Tailgate developments are driven with four entries. The recovery room, at the end of each panel, is 8m wide with three access chutes. Additional recovery room support comes for concrete blocks used with a center to center spacing of 1.5m. As the LW enters this pre-driven recovery room there are notable responses and shifting ground stresses. This study was undertaken to measure the ground response using seven vibrating wire displacement transducers. These devices were used to monitor the convergence as the LW approached the recovery room. The methane concentration in the air ventilating the recovery room was also monitored. The correlation between convergence and gas liberation was then studied. The results show that the convergence varies from 0.1m to 0.25m along the length of the recovery room. Ventilating the recovery room becomes critical as methane is liberated from oil shale as the more plastic floor material is disrupted. Appropriate methods are employed to ventilate the recovery room.

Feb 23, 2014

By Z. Y. Hu

This paper reviews the past and presents the present state of industrial minerals in China. The resources, reserve and production of major non-metallic minerals are given. The mining and milling operations are reviewed. The future development and plans of Chinese non-metallic minerals industry are summarized.

Jan 1, 1990

By Daniel B. Brimhall

The research presented here was initiated to investigate the role of atmospheric oxygen in the leaching of copper waste dumps. The problem of increasing the recovery rate of copper from these dumps is or great importance considering there are by conservative estimate in excess of fifteen billion pounds of copper located in dumps in the western United States. At this time, there is an increased interest in recovering copper from these dumps on a large scale. Large tonnages of low-grade material are being placed on the waste dumps of most copper mining operations in the western United States each day. The size of these dumps ranges from 5.5 million tons at Mineral Park, Arizona, to 4 billion tons at Kennecott&apos;s Utah operation (1). Leach solutions are recycled and contain ferrous and ferric sulfates. Large quantities of dissolved aluminum, magnesium and calcium salts may also be present. To this solution make up water is added to maintain the solution inventory and sulfuric acid is added for pH adjustment. Iron is introduced into the leach solution by the dissolution of the iron-containing sulfide and oxidized minerals present in the ore deposit. In addition to the iron from dump leaching, iron is also introduced during the precipitation process when the pregnant solution is passed over metallic scrap iron if cementation is used to reduce the copper in solution.

Jan 1, 1972

By D?Arcy R. George

A survey of the copper mining industry in Western United States revealed that uranium is almost universally present in the solutions resulting from leaching the waste ore dumps to recover copper. The U308 content ranges from about 2 to 15 ppm and a potential production of up to 1,000 tons of U3O8 per year is indicated. A six-week pilot plant test at the Bingham Canyon mine of Kennecott Copper Corporation showed that the uranium is readily recoverable by ion exchange techniques. The design of the new types of countercurrent ion exchange columns and operation of the pilot plant are described.

Jan 1, 1967

By R. Q. Honaker

Recent research has shown that enhanced gravity separators provide the opportunity to effectively clean I mm x 37 micron coal. At Southern Illinois University, a detailed experimental program was performed on a continuous Falcon Concentrator, which was found to achieve separations at mass throughput capacity values in excess of 100 tonnes/hour. The apparent particle separation density for I mm x 73 micron coal was about 1.60 with relatively high efficiency (Ep = 0.12). Typical ash and sulfur rejection values of 85% and 70%, respectively, were achieved while recovering 85% of the combustible material. Metallurgical and efficiency data from the evaluation are presented in this publication.

Jan 1, 1998

By C. L. Karr, D. E. Goldberg

This paper considers optimization of the design and operation of an air-injected hydrocyclone (AIHC) via a genetic algorithm (CAI. The AIHC is a mineral separating device, developed by the U.S. Bureau of Mines, that combines the selectivity of flotation with the capacity and simplicity of hydrocyclones. GA&apos;s are search procedures based on the mechanics of natural genetics. Computer results demonstrate the ability of a GA to rapidly locate design and operating parameters that improve AIHC performance. A computer model of the GA-designed AIHC predicts improved recovery over that currently being obtained with an AIHC in operation at the U.S. Bureau of Mines Tuscaloosa Research Center.

Jan 1, 1990

By Hayward B. Oblad, Anthony G. Fonseca

Coal flotation has been practiced since about 1920 in Europe and since about 1926 in the U.S. Over 200 U.S. coal preparation plants now use the process to recover coal. Over the 60 year period, the fundamental principles upon which flotation is based have been enumerated, but the interaction between the parameters that affect flotation has not been quantified and a useful model which accounts for these parameters has not yet been developed. A comprehensive and user friendly kinetic model coupled with better process monitoring and control instrumentation would allow plant operating personnel to better predict flotation performance and better control the flotation process in coal preparation plants.

Jan 1, 1989

By D. J. Shields

The Sustainable Minerals Roundtable was established in 1999 to develop a set of national level indicators to measure the contributions of mineral and energy systems to sustainable development in the USA. The U.S. Forest Service and the U.S. Geological Survey are sponsors of the Sustainable Minerals Roundtable, with meetings convened by the University of Nevada, Reno. Eighteen meetings have been held in various regions of the United States to receive input from different communities of interest. Indicators are being prepared under four criteria: legal and institutional, productive capacity, environmental impact, and socio-economic. This paper reviews the process followed by the Sustainable Minerals Roundtable, and presents the priority indicators.

Jan 1, 2003

By Erland A. Tillman

The U.S. National Committee on Tunneling Technology under the aegis of the National Academy of Sciences has long recognized that productivity in major underground construction projects could be increased through better contracting practices and better management. Between 1974 and 1978, this Committee has prepared three reports on these subjects. This paper reviews these reports and their recommendations. It covers the extensive actions by the U.S. National Committee on Tunneling Technology to bring the recommendations to the attention of leaders in the underground construction industry and thus further their adoption and implementation. These activities are continuing. Visibility in this session will give these reports and recommendations increased exposure.

Jan 1, 1981

By Derek J. Barratt

The existence of a critical size buildup in an autogenous or SAG mill can be predicted from proper examination of drill core and ore samples. Methods of dealing with such critical size in a primary mill are reviewed in the context of ore properties, whether or not pilot plant-scale testwork has been conducted, and also with respect to the design of new plants or the retrofitting of existing operations. The implications of not planning for pebble crushing in situations where it is appropriate are discussed.

Jan 1, 1992

By A. L. Hornbaker

Colorado has recorded more than 100 years of industrial mineral production. Much of the state&apos;s history, culture, and economy is based in mining, but the industrial minerals and construction materials comprising the nonmetallics sector of the industry very often are overlooked or overshadowed by mineral fuels and the metals. Indeed, many of these materials find use in seemingly unimportant industrial applications essential to our economy and life style and yet are not so recognized by the consumer. Unlike many other mineral resources, the numerous industrial minerals occur in many different and often exotic geologic environments, some of which are characteristic only of the western states. In Colorado only a few of these minerals have continued production through the years; many saw only "boom" periods or other critical times of need, such as the world wars. The changing needs and demands of our society in the 1980s will stimulate yet another era of intensive activity in our industrial minerals storehouse. Researchers are finding new uses and applications for these materials in dealing with the energy crisis and fuel shortages, the need to develop domestic mineral reserves of all kinds, and the goals of reuse and recycling. Some of Colorado&apos;s little-used and unused industrial minerals hold extraordinary promise in solving some of these problems on the regional and national levels. In this paper we will look at the history of development of Colorado&apos;s more prominent nonmetallics and especially at current research on and future potential of several other commodities among which Colorado contains the largest known reserves.

Jan 1, 1980

By T. A. Farr, I. A. Gibbs, F. Guevara, S. R. Simms, G. Nojima

This paper describes an installation of a medium-voltage adjustable frequency motor drive (AFD) on a high starting torque regrinding mill. This type of application is typically found in the mineral industry dealing with hard ore. The AFD electrical architecture is introduced from line to load. The type of closed loop encoder feedback motor control algorithm is briefly described. The results of the AFD motor identification auto-tuning are compared against the manufacturer’s supplied data. The motor drive performance results are shown for pre-ramp DC fluxing, high starting torque with overload current, excessive load torque stall condition, and blocked rotor. The instrumentation and arrangement for the two watt-meter method to capture low frequency data are presented. The data shown is from the input power quality meter, the AFD computer tool, the output motor protection relay, an oscilloscope, and load shaft connected strain gauge (rotating telemetry for torque assessment). These types of high starting torque constant torque loads are found in mining and process industry applications employing AC adjustable frequency drives. Using field results should help demystify the use of voltage matching output transformers in AFD applications including constant torque loads

Mar 2, 2022

By K. Kim

An analysis was conducted to determine the effects of blasting on slope stability and downstream comminution processes. To investigate these effects, the extent of blast-induced rock damage and the magnitude of induced stress were examined. This analysis showed that damage may extend up to 500 meters (1MPa, tensile strength) in the rock mass, a distance that is sufficient to impact the pit-scale slope over the long term. In addition, the damage zone was calculated using the reasonable assumption that compressive waves are the primary agent in microfracturing during blast fragmentation. The calculated damage zone ? up to 5.6 meters (30MPa, 30% of the compressive strength) ? indicates that microfracturing can occur throughout the entire rock mass in the blasting area. Finally, an economic analysis was conducted by comparing two reasonably assumed blasts in a copper mine. The change in energy required for crushing and grinding was demonstrated using Bond?s law after increasing the blast energy from 180kcal/t to 350kcal/t. A total cost saving of 13.3% ($9.4M) was achieved with the increase. An optimal blast design should consider both slope stability (safety) and downstream comminution energy (production).

Feb 23, 2014