Search Documents

By A. Aly Selirn

An economic simulation model was developed to predict the amount of copper recovered from copper oxide deposits and the cost of producing it as a function of the deposit parameters. The economic simulation model includes models of fragmentation design and cost, copper extraction, solution distribution and recovery, effluent solution cutoff grade, and financial analysis. Cost and price indices were also developed to evaluate the economic feasibility of in situ leaching operations as a function of their starting date. Application of the models to various properties having the same area and different ore thickness shows that the effluent solution cutoff grade does not vary with the ore thickness nor with its grade. The percent of copper recovery is, however, shown to increase with the increase in the ore thickness and is independent of the ore grade. it is also shown that while the profit per unit of extracted copper increases with the increase in ore grade or ore thickness, the rate of return on total investment does not show any correlation

Jan 1, 1977

By R. A. Williams

Surface and electrochemical techniques have been used to describe the surface chemistry of ferrosilicon powders, as a function of pH and electrochemical potential, for conditions typical of operating DHS plants. The practical consequences on the likely corrosion behaviour and associated electro- kinetic particle-particle interactions (which affect stability to sedimentation) in the suspension, are discussed.

Jan 1, 1987

By Andrew P. Gize

The analytical approaches used to solve a specific problem are dependent upon the information required, coupled with limitations imposed by available facilities, costs, and time. The organic matter associated with ore deposits has the potential to yield information for two problems. Information can be obtained to provide guidelines for prospecting, and, secondly, to solve genetic problems. A major potential of organic matter in providing prospecting guides lies in the high thermal sensitivity of organic matter in sediments which are metamorphosed at grades lower than greenschist facies. The organic matter can then be used to map thermal anomalies potentially associated with mineralization. The analytical approach is to determine the thermal maturity of the total organic matter, or of specific fractions, using techniques which are relatively quick and inexpensive. Consideration of genetic models (for example, reduction, complexing, involvement of oil field brines) generally requires more specific information than the overall thermal maturity of the organic matter, necessitating infor¬mation on molecular composition and structure. The facilities, time, and cost of this information are greater than for mapping thermal anomalies. The analytical techniques discussed include elemental analyses, spectroscopy (infra-red, visible and ultra-violet), Fourier Transform infra-red, nuclear magnetic resonance, extraction, pyrolysis techniques, chromatography and mass spectrometry.

Jan 1, 2013

By John J. Dran

[This paper summarizes the more popular mineral valuation techniques being used by the dining industry, and attempts to demonstrate how they are Interrelated and where some are in error when compared to modern methods of financial analysis. The academic community and the larger and more sophisticated raining companies, have largely rejected the older valuation methods such as the, Hoskold and Morkill concepts and replaced them with "discounted cash flow" (DCF) techniques. The relevancy and usefulness of the older methods have been questioned primarily on the basis of their underlying assumptions that mining companies do not have numerous alternative investments and must use sinking funds deposited at market or ?safe" rates of return to recover the purchase price of mineral reserves. The ability to reinvest In numerous (often non-mining} alternative business ventures, the changing purchasing power of the dollar, corporate income and other taxes, depreciation and depletion allowances, and modern financial management practice, all mitigate against the continued use of the older valuation methods, especially for the larger mining companies. Snail mining companies and Individuals still use these methods largely out of habit and familiarity. This paper attempts to point out the weaknesses and strengths of the valuation methods In current use in the hope that these techniques may be better understood and [rcrn] appropriately applied.]

Jan 1, 1973

By Jerry L. Fuller

Fan performance graphs are generated by digital computer using two programs, RUN- FANS and FANPLOT. RUNFANS calculates fan performance data from stored specific-volume, specific-speed data for a given fan type with appropriate allowances for fan diameter, rotational speed and air density. FANPLOT accepts specifications for drawing the graph and accepts either user-supplied pressure-quantity data or RUNFANS- calculated data as input, Operational procedures for both programs are detailed and examples of their interactive query routines are included. The hardware necessary to generate the graphs is illustrated. Several hardcopy output options are discussed,

Jan 1, 1984

By R. E. Miller

Hoisting coal using water and air is a technology which has potential to improve the economics and safety of transporting coal. The Coal Air-Lift Hydrohoist is a prototype coal hoisting system developed by the U.S. Bureau of Mines (USBM). This paper discusses the method used to regulate the supply of water to the 50-m-high hydrohoist U-tube such that the pressure difference at the bottom of the U-tube is held constant. Maintaining a constant pressure difference results in a steady flow of slurry out of the hydrohoist.

Jan 1, 1995

By P. A. Plunkert, D. E. Morse, L. McCartan, S. F. Sibley

Following the recession of 2001, restrained consumer spending, declines in domestic manufacturing and industrial output, and increased unemployment led to a lack-luster year in the domestic economy. In 2002, the U.S. real gross domestic product (GPD) grew only 2.4%. Significant production declines in the U.S. metals industry were registered by copper, lead and zinc producers. Steel producers, despite a slight improvement in shipments, continued to face strong foreign competition, higher energy costs and lower prices for their products. Homebuilding and other domestic construction sectors— major consumers of nonmetallic mineral products such as cement, brick, glass and stone — remained strong enough to help raise the output of industrial mineral materials slightly above 2001 levels. A strong U.S. dollar relative to other national currencies continued to weaken the competitive stance of U.S. metal and non-metal mineral materials companies alike against foreign producers in markets at home and abroad.

Jan 1, 2003

By Karoly (Charles) Kocsis, Kyle A. Scalise

Understanding the climatic conditions in underground mines is necessary for efficient ventilation design, cost savings, and to ensure the health and safety of mine workers. Large volumes of ventilation and climatic data including air volume, barometric pressure, dry bulb temperature, and relative humidity were collected at active underground precious metal mines in Nevada, which allows for the determination of wet bulb temperature and other key parameters. Through the utilization of neural networks, the wet bulb temperature at the bottom of the intake shafts is predicted, while taking into account the “thermal flywheel effect” (TFE). Wet bulb temperature is one of the most important climatic parameters to model and understand because it significantly affects the work conditions and the cooling capacity of the ventilating air. The accurate prediction of the dry bulb and the wet bulb temperatures at the bottom of intake shafts is critical when assessing the climatic conditions in future underground mines and deciding onwhether a cooling system is needed to assure adequate working conditions throughout themine. By utilizing accurate predictions of wet bulb temperatures and other climatic parameters, mine personnel will be safer as reported by Bluhm et al. (2003), and a more accurate ventilation design can be achieved resulting in major cost savings for underground mines.

Mar 3, 2021

By F. Ikumapayi

In order to predict and minimize detrimental production problems due to the recycling of process water in sulfide ore processing, the influence of major species, calcium and sulfate in process water on sphalerite flotation was investigated through Hallimond tube flotation, zeta potential, diffuse reflectance Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS) measurements using sphalerite mineral sample. Assessment of process water species in flotation was done using deionized water, process water and simulated water containing calcium and sulfate ions in experiments. Hallimond flotation shows increased sphalerite float-ability in process water compared to deionized water, but no significant effect on the presence of calcium and sulfate ions in deionized water using isobutyl xanthate as a collector. The presence of calcium ions reduced the sphalerite?s negative zeta potential, while at higher concentrations, a charge reversal occurred, at about pH 11. FTIR and XPS studies revealed the presence of surface-oxidized sulfoxy and carbonate species on sphalerite at pH 11.5 in deionized water, process water and water containing calcium and sulfate ions. These surface species do not influence xanthate adsorption.

By A. I. Johnson

This paper describes," the application, of a modular or building block approach to the analysis, design, and control of complex mineral treating processes. The main purpose of the paper is tutorial, to show the reader how such processes can be modeled using a modern digital computer" and, not to discuss in any detail the results that may be achieved in such studies. It is proposed that, the main techniques be illustrated by reference mainly to the Bayer process for alumina extraction and purification; in cooperation with the Aluminum Company of Canada Ltd. the author and his Colleagues at McMaster University and their students have studied this, process as a means of applying new computer techniques to extractive metallurgical processes. The plant described was studied by the author and his colleagues as a senior undergraduate project in cooperation with the Aluminum Company of Canada. It is one of several studies that have been carried out with Canadian industry. (1)

Jan 1, 1972

By George Schmitt, Ted Dowey, Grant Millener, Sean McAndrew, Eric Jordan

The Rondout-West Branch Bypass Tunnel is being built to bypass a substantial leak in New York City’s primary water supply tunnel. The 13,500 foot long tunnel travels 600 feet under the Hudson River through the same troubled geology and high pressure water inflows that the original tunnel did in the 1940s. A Robbins TBM traversed this geology and built gasketed segments. Nine thousand two hundred feet of 16 foot diameter interliner was installed and backfilled within the segments. Finally, reinforced cast in place lining was placed. This paper addresses the challenges and the multi-tasking approach the contractor utilized.

Jun 13, 2021

By Yinan Zhang, Yi Luo

The widely used R70 method is modified to measure the self-heating propensity of low-rank coals. This modified R70 method enables the introduction of controlled amount of moist oxygen into the reaction vessel. Three coal lumps were collected from three different locations in a surface mine in the Powder River Basin. The coal samples were tested in oxygen flow with controlled moisture content under adiabatic condition. By measuring the relative humidity at the exhaust exit point of the testing setup, the flux and cumulative wetting heat that is consumed by coal samples can be determined. Through a better way of determining the coal’s specific heat, the total heat, including heat of wetting and coal’s oxidation heat, required to raise coal to a given temperature can be determined. Then, the contribution of heat of wetting at the different stages of the testing is quantified. The effects of evaporative heat through a group of tests have also been quantified. From this research, a better understanding of the effect of wetting heat on inducing low-rank coal’s spontaneous combustion can be acquired.

Nov 30, 2022

By Juan J. Monsalve, AMAN SONI, Nino Ripepi, Richard Bishop

The design and strength of pillars are important parameters while implementing the room-and-pillar mining method in a limestone mine. The process becomes complex with the presence of the karst voids which are frequent phenomena in a carbonate rock formation. The karst system is a network of cavities that along with an omnipresent fracture network may lead to ground control issues in a limestone mine. The objective of this study is to provide a safe and reliable alternative design for a pillar in a case study mine for safe and efficient ore recovery. This research is a continuation of a previous study aimed at studying the effect of karst void on the strength of the same limestone pillar. It was assessed from the calculated pillar strength and the estimated redistributed stresses that the pillar is capable of countering more stress than is currently imparted on it. Numerical modeling studies combining in situ stress determination and excavation sequencing were used to estimate the existing stresses on the pillar. Different possibilities of modification to existing pillar design were simulated using Distinct-Element Modeling (DEM) to determine a better design. Discrete fracture networks (DFNs) were included to imitate the effect of the presence of discontinuities. An effort is also made to understand the variation of pillar strength with height for karst-affected pillars using two different constitutive models. This study serves as a preliminary investigation in terms of improving the future design of pillars and also while recovering old pillars prone to karst formation.

Jan 30, 2023

By Martin B. Treuhaft

Expectations for coal in the early to mid-1970's prompted the government and industry to pursue research and development programs to increase underground and surface mining coal productivity and net coal recovery. Several programs concerned advanced surface mining methods for thin seam coal recovery. Three such programs, along with related areas of interest, are presented in this paper, namely: (1) extended depth augering for trench-strip applications; (2) high recovery auger heads for enhanced recovery; and (3) variable wall mining in low cover longwalls. Conceptual development is examined, prototype testing is discussed, and potential operations are considered.

Jan 1, 1983

By Jack M. Campbell

The regulatory process by which governmental authorities acknowledge and, in turn, permit the location, construction, and operation of large scale energy-related facilities has become extremely detailed in recent years. One example of the detail that is entailed in the regulatory process is the number of permits that must be acquired by operators prior to the construction and operation of energy-related facilities. It has been estimated, for example, that 75 permits are required prior to the opening of a new coal mine in Pennsylvania while 50 are required in Kentucky. From the perspective of facility owners and operators the regulatory process often appears overly complex and may be perceived as a constraint to the corporate decision making process. From the perspective of those responsible for administering regulations, the process is perceived as a mans by which public desires - pursuant to social objectives such as environmental protection and occupational safety - can be achieved. As a result of conflicting organizational interests, the clash between energy facility owners and operators and their regulators appears to be inevitable. Furthermore, the resolution of this conflict lies in the tradeoff between objectives and the costs of regulation. The balance of objectives and costs is a subject of the political process and not a topic of consideration in this paper. This paper is concerned with the actual administration of regulations, that is, the implementation of that which arises from the interplay of organizational interests. The paper assumes that environmental control laws will not likely be repealed, that regulations to implement the intent of these laws are here to stay and thus the paper seeks to assess how regulations are administered at various levels of government pursuant to objectives. The paper hypothesizes that the administration of objectives (or policy) has an impact on decision making which affects energy facility decision; making while recognizing the fact that regulatory policy cannot be totally divorced from administration, this paper proceeds

Jan 1, 1977

By K. S. Fraser, R. Frischmuth

High temperature pressure oxidation (>190°C) is a wellrecognized and versatile metallurgical oxidative pre-treatment process commonly used to liberate gold from refractory sulfide ores and concentrates. The pressure oxidation of refractory gold ores was first commercially applied in 1985, at Homestake Mining Company’s McLaughlin mine in the United States. Since that time numerous refractory gold and other high temperature pressure oxidation facilities have been built throughout the world. The design of each facility was met with unique challenges and opportunities which have led to an array of plant configurations, pressure oxidation autoclave sizes, and sulfide oxidation capacities. This paper presents a historical review of high temperature pressure oxidation operations and current projects in execution with a focus on the autoclave vessel design, circuit configuration, and unit sulfide oxidation capacity as a basis for characterization and comparison.

Mar 2, 2022

By S. D. Bearden

The world's reserve base is adequate for at least 100 years at the current consumption rate. China, India, and the U.S. are expected to remain the leading producing countries. The U.S. will continue to be the largest consumer of the production. None of the known substitutes for barium sulfate are expected to impact existing applications. World production in 1995 was 4,410Mt. This is about 50% of the projected capacity. Consumption is directly proportional to hydro-carbon well installation activity. Imports are expected to continue to supply more than half of the U.S. requirements.

Jan 1, 1997

By Chaoxun Zhao, TAIYOU LI, JIAQI JIN, Jan D. Miller, Chen‑Luh Lin

A large portion of the energy consumed in copper concentrators is used to reduce the particle size of the feed by crushing and grinding. The cost of metal production could be reduced if low-grade particles of cm size were removed prior to further processing. Two copper sulfide ore samples (3 × 1 cm) from Arizona were analyzed by micro X-ray computed tomography (Micro-XCT) to determine the grade of copper sulfide in each particle. For copper ore sample A, a significant number of particles contained very low amounts of copper, while some particles had copper sulfide grains of mm size. Based on Micro-XCT, it was expected that 85% of the copper for sample A could be recovered at 65% of mass rejection during preconcentration by sorting. However, in sample B (a different copper ore), distribution of copper sulfide was dispersed primarily in each ore particle, so for the particle size class of 3 × 1 cm, liberation of copper sulfide and gangue minerals was not significant. In view of the XCT results, dual energy (DE) X-ray radiography was used as a basis for sorting. Previous DE X-ray radiography of a drill core sample demonstrated that this rapid detection method can be used to identify rich or poor Cu-bearing coarse particles. Pilot scale X-ray sorting of sample A (10 × 1 cm) showed 31% rejection of a 0.08% Cu gangue product with a corresponding recovery of 90% copper.

Nov 30, 2021

By M. A. Greenwood

The total value of coal, FOB mine, consumed in the United States was $21 billion in 1985. Roughly $6 billion was spent to transport coal from the mine to the consumer by rail. This indicates the impact railroad transportation has on the competitiveness of U.S. coal as an energy resource. Actually, this is just the tip of the iceberg. When you consider the largest U.S. reserve of coal, the Powder River Basin, which is possibly the lowest cost coal in the U.S., or maybe even the world, the transportation cost is the overriding factor in developing competitive pricing. Rail transportation costs from Powder River can be multiples of 2, 3, or even 4 times the cost of coal FOB mine. About sixty percent of all U.S. coal is shipped by rail. In the case of Powder River Basin coal and many other reserves there are no current alternatives to rail. Are there feasible alternatives to rail transport?

Jan 1, 1986

By Frank F. Aplan

Froth flotation has been used to improve the recovery of fine coal, for minimizing the sulfur and ash content of clean coal and for the removal of fine coal from recycled or discharged backwater from coal preparation plants. Though froth flotation and allied processes for ores date from the turn of the century, with the first U.S. commercial application in 1911, coal flotation has been introduced into U.S. practice much more slowly. The first European coal flotation plant was started in 1920, and by 1933 Europe had 60 operating plants while the United States had only one plant, newly commissioned. Over the years there has been a steady increase in coal flotation so that today one-third of the 345 U.S. plants employ the process. This report traces U.S. coal flotation practice and technological improvements from early laboratory experiments in 1915 up to today's extensive use of the process.

Jan 1, 1999