Search Documents

By Hendri Silaen, Charles Leatemia, Monang Napitupulu, John Kamarea, Arwin Edijanto, Riza Hasan, Avesiena Primadiansyah

The Deep Mill Level Zone (DMLZ) is the fourth panel cave mine in the East Ertsberg Skarn System, (EESS) which lies 500 m below the producing Deep Ore Zone (DOZ) mine and up to 1,700 m below the surface. The interaction between the DMLZ and DOZ is occurring as the DMLZ cave grows vertically toward the DOZ footprint. During this process, a rapid change in the global mine system stress is anticipated. This change is forecasted to drive substantial changes in the magnitude and direction of principal stresses in the DMLZ and DOZ mines at PT Freeport Indonesia. These changes will bring the mine system closer to the ultimate capacity of the excavations and can result in significant impacts to mine stability if not managed. Critical to this management, is understanding cave growth and locations, as well as how these changes will impact stress conditions.

Apr 26, 2022

By M. J. Gula, S. S. Xue, E. P. Horwitz

A study was conducted to remove iron from sulfate solu¬tions using Eichrom'sDipex®extractant, PP'-di(2-ethylhexyl) methanediphosphonic acid (H2DEH[MDP]). It was found that this extractant can effectively and selectively extract ferric ion from highly acidic solutions. Ninety-nine percent of the iron was extracted from a simulated feed solution in a single stage. The separation factor, Fe/Zn, was 106. More than 90% of the iron in a loaded organic can be recovered in an aqueous solution by reductive stripping. This paper presents the experimental results. A new process for iron removal using Dipex extractant is described and discussed.

Jan 1, 2000

By Enrico Pavese, Tim Kearney, Stefan Lemke

Watertightness is of central importance in hydraulic and underground structures but has always been associated with a risk, as demonstrated by the very high impact that water inflows have on the damage of linings and infrastructure (Howard, 1991; Sandrone and Labiouse, 2011). Concrete is vulnerable to groundwater and chemical contaminants in the soil. These can leach into the pores and cracks of the concrete and degrade its integrity, causing spalling and corroding the reinforcing steel. Moisture migrating into the building can also degrade structural elements over time and lead to mold and other hazards to occupants’ health. In this connection, the demands placed on the setup and detailed design of the seal depending on the negative influence by water on the one hand and on the other hand on the function of a construction in view to its watertightness classification. Thus, the reliable functioning of a seal is of particular significance in the case of traffic tunnels, which are not easily accessible for all subsequent repairs after the construction in seepage water and especially when located in a pressure water zone (risk–cost assessment). Requirements for the long-term efficiency and quality of underground structures have increased in recent decades. Today, the standard lifetime requirement for an underground infrastructure project is 100 to 120 years and, in some cases, even higher. This calls for high increased attention to the durability of the whole structure and of each individual element. Standards, which started as application guidelines given by the manufacturers, are available in the market since the 1980s and are constantly adapted to the current developments in various technical committees. Differentiations are made between: Manufactures application guidelines, case studies or published articles Test standards for the laboratory to guideline the testing procedures (air temperature, type of test equipment, dimensions, test speed, test duration, concentration, type of liquids, monitoring, tolerances, interpretation of results, documentation, etc.), developed by committees based on material and laboratory experts Application standards, which include test standards but also the related minimum performance requirements (values) for material, processing, and quality assurance (practical tolerances), developed by committees based on a wide range of experts (e.g., designers, construction companies, applicators, manufactures, owners, test institutes, quality engineers) and therefore also based on a wide field of experience, different views and up-dated case studies. In the following there are some examples of guidelines and published information’s, ranked according to the year of issue, which are relevant for the development of waterproofing specifications in the tunnel industry:

Jun 13, 2023

By Guowen Dong, Qiyong Li, Qiang Li, Tiejun Chen, Zhihong Wu, Junying Wan

In order to search for a more economical and effective roasting additive for extracting vanadium from stone coal and solve the question of the disposal of PVC waste, PVC waste was proposed as a novel roasting additive to enhance extraction of vanadium from stone coal and realize the comprehensive utilization of resources. By adding this roasting additive, the leaching rate of vanadium reached 94.5% under the conditions that the PVC waste addition was 10 wt%, the roasting temperature was 800 °C, the roasting time was 1 h, the sulfuric acid concentration was 15 vol%, the liquid-to-solid ratio was 1.5 cm3 /g, the leaching temperature was 95 °C, and leaching time was 4 h, which increased by 8.4% compared with that of blank roasting. The thermodynamics calculation showed that the decomposition reaction of mica was performed easier with the participation of HCl produced by pyrolysis of PVC. Meanwhile, The SEM-EDS and aperture test analyses demonstrated that more cracks and voids appeared in the roasted sample by roasting with PVC waste, which could facilitate the release and extraction of vanadium. Additionally, the TG-DSC analyses indicated that PVC could provide large amounts of heat for the roasting process to promote the decarbonization and roasting efficiency of stone coal because of its high calorific value.

By McDonald E. Wrenn, Narayani P. Singh, Victor E. Archer, Ceno Saccomanno

Fourteen uranium miners' lungs from Colorado plateau were collected at autopsy and the concentrations of 238U, 234U and 230Th were determined by radiochemical procedures utilizing solvent extraction - alpha spectrometric techniques. The uranium and thorium isotopes are in near equilibrium with average concentrations of 238U, 234U and 230Th being 89.3, 95.2 and 91.1 pCi/kg respectively. The combined average radiation dose rate to lung from these three isotopes is about 24.2 mrad/year at death excluding the unmeasured contribution from the 226Ra and daughters. The average concentration of 230Th is about 65 times higher than the mean concentration of 230Th in lungs of non-miners dying at comparable ages from the same region.

Jan 1, 1981

By Donald E. Zipperian

The studies described in this paper have established that flotation conducted in a column cell provided with gas generation by aspiration into surface tension lowered water, may considerably increase the efficiency and particle size range of a flotation process. Operation of a DEISTER FLOTAIRE ® Cell at several Southwest United States flotation plants under continuous rougher, scavenger and cleaner conditions has demonstrated the main positive features to be: (a) higher capacity per unit volume than conventional flotation equipment, (b) improvement of flotation of plus 0.210 m particles, (c) improved flotation of particles minus 0.037 m.

Jan 1, 1984

By Stephen J. Swan

Feed-forward control (i.e. the forward flow of information in a control system ) is a simple and flexible approach to over-all control of a ball mill-rake classifier grinding circuit. The system described here uses mill power, feed rate, mill dilution water flow rate, and classifier dilution water flow rate only, to control mill load, throughput, mill solids, and classifier solids as well as classifier overflow grind. The mill load is controlled by a simple feed-back control loop, while mill solids and overflow grind are controlled within close limits by a unique non-linear feed-forward water control system. In effect the control follows a limited mathematical model of the grinding circuit. The configuration minimizes deviations in overflow grind due to changing ore conditions, but since it is open-loop, and the model is not complete, it is affected by changes in total ball charge and liner wear. These effects are fortunately gradual, and changes in the grind can usually be kept to within ± 1% of a target continuously for several days without adjustment. Control adjustments are made with feed-back from laboratory composites. This control system has won enthusiastic operator acceptance; it is easily started up and shut down; grind-outs have been eliminated along with flotation machine flooding and mill spills. Standard measurements and components are used throughout providing a trouble-free system design at a moderate cost.

Jan 1, 1970

By Arthur W. T. Grimley

Hydraulic coal mining is being successfully practiced in China, U.S.S.R., Japan and Canada and in each country, excepting Japan where suitable sites are not available, the system is being expanded to either existing conventional mines or new mines. Productivity levels and economics at these mines are in all cases better than the productivities achieved in conventional mines in the same general localities. In the U.S.S.R. face productivities approaching 50 tons per man shift have been reported while in Canada the latest statistics show average face area productivity levels are in the region of 200 tons per man shift production monitor. In the United States hydraulic mining has not been actively pursued to the same degree and consequently there are no full scale hydraulic coal mines in operation or construction. Because many of the coal measures in the Western U.S.A. are generally somewhat similar to those being successfully hydraulic mined in Western Canada and parts of Siberia it is realistic to believe that successful hydraulic mines can be designed and developed in the Western U.S.A. Particularly if the vast technological base that already exists is used to improve on other people's ideas, systems, methods and equipment.

Jan 1, 1983

By L. J. Blatnica

Throughout the 1980's the tem Mine-Wide Monitoring System has had various meanings for manufacturers of these systems and underground mine operators alike. System suppliers had visions of grandeur in the early 80's as they envisioned each mine, that has more than a single section, installing a computer based monitoring system to provide surveillance, control and documentation of the entire mining operation, including everything from a single heat detector to the weekly payroll. In a few cases this may have become reality but the truth is these systems have quietly become a steady but unspectacular workbase for the modern mining industry of the 1990's. As it exists today the total market for underground monitoring systems may not exceed $10 million annually. Suppliers have lowered their expectations of the dollar value of this particular market. Some were entering a new market because of experience with computer based data acquisition systems. Others had been active in the mining industry for years with more traditional equipment (communication systems, methane monitors, safety equipment, etc.) and decided to become involved with Mine-Wide Monitoring Systems.

Jan 1, 1990

By Richard Emberley, Timothy Shaw, José L. Torero, Jurij Karlovsek, Timothy Gibson

"Tunnel closures are highly undesirable and the lengthiest are generally attributed to structural failures (e.g. Mont Blanc). Although historical data shows structural failures are closely linked to fire, design parameters for tunnel safety are not well defined. Current research has focused on defining the fire heat release rate and temperature, but these parameters cannot be easily used to determined structural performance. The energy transferred to the structure, the heat flux, is required but current literature lacks these values. Full scale experiments were undertaken on passenger vehicles resulting in heat fluxes between 20-70kW/m2. Analysis shows a vehicle fire’s duration is closely linked to its mass. Further analysis shows small vehicle fires can be scaled as a function of the tunnel diameter and the characteristic height of the desired vehicle. The present work provides engineers an appropriate design methodology to undertake informed thermal-structural analysis to minimize the risk of tunnel structural failure.INTRODUCTION Quantifying the effects of a tunnel fire depends on many factors such as the type of occupants, their vehicles and spacing, ventilation conditions and the geometric shape of the tunnel (Ingason and Lonnermark 2011). For design engineers investigating the thermal-structural performance of a tunnel, these factors are typically converted into spatial and temporal temperature distributions (Usmani et al. 2001) using various design curves such as those of ISO834-1, Hydrocarbon, Rijkswaterstaat (RWS) or RABT-ZTV (Promat 2013). However, to define a temperature profile through a structural element these curves require a heat transfer model that incorporates an appropriate boundary condition. The appropriate boundary condition is the net heat flux which is the result of a complex energy balance. For use in heat transfer calculations the net heat flux must account for the tunnel geometry as well as thermal properties of a given structural element and all other surfaces and mediums affecting the transfer of heat (Torero 2014)."

Jan 1, 2016

By William Hodder, Ehsan Alavi, Nader Ghasempour, Daniel Cressman

The Don River & Central Waterfront Coxwell Sanitary Bypass Tunnel (CBT) Project in Toronto will extend approximately 10.5 km from Ashbridges Bay Treatment Plant west under Lake Shore Boulevard, north under Bayview Avenue and east through the Don River park area to the Coxwell Ravine Park. The tunnel is currently being mined by using a shielded dual-mode tunnel boring machine (open and close) capable of operating in EPB mode and lined by using a precast concrete segmental tunnel linear with an internal diameter of 6,300 mm and external diameter of 6,900 mm. The CBT is expected to be excavated mainly through shale bedrock of the Georgian Bay Formation, at approximately 50 meters deep. The tunnel crosses a buried bedrock valley in two locations, in the southern portion of the alignment, adjacent to the Don River, and at the northern portion of the alignment approaching the CX-1 shaft. In these two locations, the bedrock cover is expected to be less than 6 meters. The risk of encountering weathered bedrock, significant ground water inflows or surficial soil deposits through these buried valleys was identified during the design phase. The contract required the TBM to be designed with the ability to probe drill ahead of the TBM and convert to EPB mode if necessary, to cross this area. This paper will discuss the additional exploration that was performed by the contractor to identify the extent of this buried valley, the plan going into the zone of potential weathered shale, and the actual conditions encountered.

Jun 13, 2021

By Roland Arnold, Richard Gradnik, Martin Zeindl

This paper presents the details of the Kramer tunnel project in the Federal State of Bavaria, Germany. This road tunnel, which has been under construction since December 2019, is the key component of the western bypass of the town of GarmischPartenkirchen. Once completed, it will relieve the town’s central district from enormous volumes of traffic. The contractor is the joint venture named ARGE Kramertunnel consisting of BeMo Tunnelling and Subterra. The whole project will be completed and handed over to the project owner, Staatliches Bauamt Weilheim, in 2023. The opening of the entire bypass section including the tunnel to traffic is planned for 2024. The tunnel, with a total length of 3,609 m (2.24 miles) and an estimated cost of EUR 178 million (incl. VAT), is designed as a single-tube, double-lane structure with one traffic lane for each direction of travel. The safety issue that exists for single-tube tunnels is solved by a parallel escape tunnel passable for vehicles. All tunnels and ducts are excavated according to the principles of the New Austrian Tunnelling Method (NATM). In order to reduce the geological risk for the owner, the escape tunnel was supposed to be completed before the design process for the main tunnel ever began. The exploratory tunnel was awarded to a competitor with an separate contract.

Jun 13, 2021

By Fred Morelko, Michael Connelly, Brad L. Ricks

INTRODUCTION The $1.1 billion Bajo la Alumbrera Project, started up in 1997 by Minera Alumbrera Limited in the Catamarca Province of Northwestern Argentina, is the first large scale modern mining project to be developed in Argentina. Like many modern Andean mining projects, existing infrastructure was not available to economically transport the 875,000 tonnes of product per year. A variety of alternatives were investigated, including upgrading of existing roads and railroads, slurry pipelines, and combinations of these systems. The final system selected was to combine a 312 km slurry pipeline with an 820 km rail haul to a ship loading facility near Rosario. The concentrate pipeline crosses divergent terrain between the minesite at 2400 m elevation and the filter plant at 400 m elevation. The system selected represented the lowest net present cost alternative by a significant margin. BACKGROUND The Bajo Alumbrera deposit was discovered in 1947 by Professor Cetioni from the University of Tucuman. It is a large (>750 million tonnes) medium-grade (0.6%) copper deposit with high gold values (0.5 g/t*). The deposit outcrops, making it very suitable to modern, large scale, open pit mining techniques using 218 t trucks and 43 m3 shovels. Advances in gravity concentration of the gold helped to demonstrate the feasibility of the project in a study prepared by Fluor Daniel for Minera Alumbrera in 1994. The initial concentrator is the largest green-field concentrator ever constructed, rated at 85,000 t/d. Production will peak at 190,000 tonnes of copper metal and 710,000 troy ounces of gold per year, one of the top 10 copper and top 15 gold producers in the world. * Throughout this paper, the word tonne and abbreviation refer to the metric ton of 1000 kg.

Jan 1, 1998

By Gary B. Glass

In 1997, 92.3% or 235.7 Mt (259.8 million st) of coal produced in Wyoming came from the Wyodak coal zone in the eastern Powder River coalfield. The mined portions of the zone consist of one to three beds of coal with an aggregate thickness between 15 and 33.5 m (50 and 110 ft). The thickest expression is 61 m (200 ft). The delivered coal from this zone averages 0.33% sulfur, 5.12% ash and 19.98 MJ/kg (8,590 Btu/lb.). This coal zone occurs at or near the top of the Paleocene Fort Union Formation, which is overlain by the Eocene Wasatch Formation. There is also production from two coalbeds in the lower portion of the Wasatch at the southern end of the basin. Production of coalbed methane derived from the Wyodak coal zone is currently an estimated 289 Mm3/a (10.2 billion cu ft/year). This production is occurring west and downdip from the coal mines and is increasing each year.

Jan 1, 1998

By Joel Nonnweiler, David Young, John Hawley

The Sacramento Regional County Sanitation District has implemented a billion-dollar interceptor system master plan, including the 31 km (19 mile) long Lower Northwest Interceptor (LNWI). For the two LNWI Sacramento River crossings, pipe-jack/micro tunnel drives in excess of 300 meters (1,000 ft) from 30 meter (100 ft) deep shafts in mixed soil conditions below the water table were considered, as were600 meter (2,000 ft) tunnel drives utilizing pressurized-face tunnel boring machines. Operation and maintenance concerns, predicted flood scour, and levee concerns are discussed. A risk assessment process was used to select both profile and construction method. Construction will begin in mid 2004.

Jan 1, 2003

By John A. Reeves

The unit-train concept of moving raw materials .is considered by many railroad men as the most signifigant contribution to reducing rail freight costs since the introduction of the diesel locomotive. The idea, which involves assigning railroad equipment to only one haul and keeping the equipment rolling results in the maximum utilization of equipment. For example before the unit train was plaged in servige on coal hauled to one of Mid. Continent's customers, about 900 cars and 9 locomotives were needed to move the coal requirements for this plant, compared with. 250 cars and 6 locomotives used by the present scheduling of unit trains. If the economics of unit-train movements are to be achieved, coal companies no longer can use railroad cars as small storage bins on wheels to accumulate their coal in trainload shipments, but, rather, must build large bins which incorporate facilities for the rapid loading of railroad cars in a minimum length of time. In this manner railroad equipment is operated at a high degree of efficiency 'with consequent dollar savings. After negotiations between Mid-Continent, the customers and the Railroad, it was decided a unit train loadout and storage facility at Carbondale was required in order to reduce the delivered price of coal to the customers and thereby contribute to the reduction in the cost of manufacturing steel. Carbondale was selected as the bin site location, because the cost of constructing a railroad to Redstone could not be justified for the tonnages anticipated.

Jan 1, 1969

By WILLIAM M. CROSS, ALBERT ROMKES, BERNARDO MORENO BAQUEIRO SANSAO, Jon J. Kellar

In this research study, the interaction of particles with substrates of different roughness magnitude was investigated. Particle surface treatment, relative humidity (RH), and surface roughness levels were controlled in order to achieve separation of different particles by applying removal forces. Three different approaches to reproducibly roughen surfaces were used. Initially, glass disks were laser engraved to create a reproducible, controlled roughness substrate. However, the laser engraving method produced surface features that were much greater in scale than the particles. These scale differences were such that the substrates produced were not of value to this research. The second option investigated to induce reproducible substrate roughness was to scratch the glass disk using sandpapers of known grain size. A third approach to establish reproducible roughness was to use fine stainless-steel wire mesh substrates. In tests with sanded glass disks, the interfacial energy of plasma-cleaned (hydrophilic) glass beads had a high variation at 40% RH, showing non-uniformity of area of contact between particles and substrates. As the RH increased, it was expected that the interfacial energy of hydrophilic particles would increase, but this behavior was not observed. In addition, comparing the interfacial energy results of hydrophilic particles with hydrophobic particles, a region with significant interfacial energy difference was not identified. In the case of the stainless-steel mesh substrate, the mesh asperities and particle dimensions were comparable. Thus, the smaller particles had more area of contact with the substrate than the larger particles. For the plasma-cleaned (hydrophilic) beads, the recovery values had an average of 92.5% recovery when the RH was between 46 and 85%. For the hydrophobic beads, the average recovery was 19.0% when the RH was between 46 and 75%. Thus, the hydrophobic characteristic of the particle influenced its lower interaction with the mesh substrate. The difference in recovery can be exploited to achieve separation of particles based upon adhesive forces.

Nov 30, 2021

By W. Z. Choi

In our previous work, a population balance model describing the simultaneous processes of size reduction and mineral liberation has been developed. The experimental verification of this model, however, has been limited to a binary mineral system containing only one composite particle class. When considering multiple classes of composite particles, the estimation of model parameters becomes much more difficult. In the present work, a procedure for estimating model parameters for a multiple composite class model has been developed. Emphasis is placed on the direct experimental determination of these parameters. The physical significance of the breakage rate function and the liberation function in characterizing the liberation process is also discussed.

Jan 1, 1987

By Richard L. Sanford

This paper summarizes the results of the development of a Directory of Computer Programs Applicable to U.S. Mining Practices and Problems. The Directory is funded by the U.S. Bureau of Mines and includes a sampling of computer usage in operating and manufacturing companies, consulting firms, computer companies, research organizations, universities, and various U.S. government agencies. General references to computer applications throughout the mining industry are discussed as well as the availability of programs to interested organizations or individuals.

Jan 1, 1978

By G. Swartz, R. J. Brison, R. A. Wyman, J. P. Vandenhoeck, S. E. Khalafalla

Magnetic fluids are commonly composed of ultrafine submicron particles of magnetite (Fe3O4) dispersed in either a kerosene or a water carrier medium with oleic acid as a protective colloid. The unique property of these fluids is that when the magnetic particles are attracted to a magnet the carrier medium moves along with the particles so that the liquid also appears magnetic. The availability of a fluid whose gross behavior changes sharply in a magnetic field without affecting its rheologic characteristics is becoming critical for many technologic applications. About two gener¬ations ago suspensions of relatively large, micron-sized ferromagnetic particles in oil proved useful in clutches, brakes, and dashpots. These were called magnetic clutch materials, and their viscosities were highly dependent upon the applied magnetic field, in contrast to true mag¬netic fluids which retain their fluidic characteristics under all applied fields and field gradients. While the term "ferrofluid" was used by Rosensweig and Kaiser&apos; to designate a magnetic colloid composed of a dispersed magnetic ferrous material, the more general term, "mag¬netic fluid," is preferred. This is because these fluids may contain ferro- or ferrimagnetic substances, such as cobalt, nickel, gadolinium, dysprosium, or magnetic ferrites in carrier liquids, such as hydrocar¬bons (kerosene), silicones, water, fluorocarbons, etc. Preparation of Magnetic Fluids Magnetic fluids were first prepared by Papell and Faber, at the NASA Lewis Research Center, Cleveland, Ohio, by tumbling ferrite materials for several weeks in a carrier medium (such as kerosene) and a dispersing agent (such as oleic acid) with steel balls. Rosensweig et al.1 compared the stability of their ferrofluids obtained from both metallic iron and the magnetic oxides of iron, Fe3O4 and yFe2O3. They found that, although the saturation magnetization of iron is 3.5 times greater than that of magnetite, its colloidal solutions deterio¬rated much more rapidly. The iron particles were undoubtedly rapidly oxidized to a nonmagnetic state due to the enormous surface area of these colloidal particles. Because the properties of these fluids are highly dependent on particle size and may acquire opposite characteristics by small incre¬ments in that size, more controllable methods of preparation have been developed recently by Khalafalla and Reimers.6 In one method metastabilized pyrophoric wiistite is ground to colloidal size in a kerosene oleic acid mixture, and then it is disproportionated to colloi¬dal magnetite and iron at temperatures just below the eutectoidal temperature of wüstite stability (570°C); thus, t < 570°C 4 FeO t > 570°C Fe + Fe30, (1) Because of its antiferromagnetic characteristics, the precursor wüstite is much easier to grind than magnetite. Another method3 avoids grinding entirely and utilizes a peptiza¬tion technique from ferrous materials in the molecular state of aggrega¬tion. This latter procedure has resulted in preparation of strong fluids at considerable savings in cost.

Jan 1, 1985