Search Documents

By M. S. Safarzadeh

Over the last fifty years, the treatment of enargite concentrates has not received much attention, primarily because of the availability of other clean concentrates suitable for processing with existing smelting and/or leaching technologies. As traditional copper ores have become scarcer, copper-arsenic ore deposits have garnered more interest. Arsenic release is a significant concern during the treatment of enargite concentrates by pyro or hydrometallurgical methods. Enargite is also very refractive in standard leaching procedures. Thus, economical treatment options for enargite concentrates are needed. Preliminary experiments have shown that the acid bake-leach process could be adapted and used for the treatment of enargite concentrates. In this study, low-temperature (100-400º C) sulfuric acid baking of an enargite concentrate followed by water leaching has been evaluated. The results indicate the thermal transformation of enargite to copper sulfate happens during sulfuric acid baking, with most of the arsenic being released from the concentrate into the gas phase when baking at 400º C. The condition for maximum copper extraction (~100%) from the concentrate was found to be 400º C, a sulfuric acid concentration of 0.5 mL/g and two hours baking time. Part of the arsenic was captured in the form of arsenopyrite (FeAsS). X-ray diffraction (XRD) analysis proved the presence of some arsenic in the form of claudetite (As2O3) in the baked concentrate. Acid baking of pure enargite behaved in a similar fashion.

Nov 1, 2011

By Hendri Silaen, Charles Leatemia, Monang Napitupulu, John Kamarea, Arwin Edijanto, Riza Hasan, Avesiena Primadiansyah

The Deep Mill Level Zone (DMLZ) is the fourth panel cave mine in the East Ertsberg Skarn System, (EESS) which lies 500 m below the producing Deep Ore Zone (DOZ) mine and up to 1,700 m below the surface. The interaction between the DMLZ and DOZ is occurring as the DMLZ cave grows vertically toward the DOZ footprint. During this process, a rapid change in the global mine system stress is anticipated. This change is forecasted to drive substantial changes in the magnitude and direction of principal stresses in the DMLZ and DOZ mines at PT Freeport Indonesia. These changes will bring the mine system closer to the ultimate capacity of the excavations and can result in significant impacts to mine stability if not managed. Critical to this management, is understanding cave growth and locations, as well as how these changes will impact stress conditions.

Apr 26, 2022

By Enrico Pavese, Tim Kearney, Stefan Lemke

Watertightness is of central importance in hydraulic and underground structures but has always been associated with a risk, as demonstrated by the very high impact that water inflows have on the damage of linings and infrastructure (Howard, 1991; Sandrone and Labiouse, 2011). Concrete is vulnerable to groundwater and chemical contaminants in the soil. These can leach into the pores and cracks of the concrete and degrade its integrity, causing spalling and corroding the reinforcing steel. Moisture migrating into the building can also degrade structural elements over time and lead to mold and other hazards to occupants’ health. In this connection, the demands placed on the setup and detailed design of the seal depending on the negative influence by water on the one hand and on the other hand on the function of a construction in view to its watertightness classification. Thus, the reliable functioning of a seal is of particular significance in the case of traffic tunnels, which are not easily accessible for all subsequent repairs after the construction in seepage water and especially when located in a pressure water zone (risk–cost assessment). Requirements for the long-term efficiency and quality of underground structures have increased in recent decades. Today, the standard lifetime requirement for an underground infrastructure project is 100 to 120 years and, in some cases, even higher. This calls for high increased attention to the durability of the whole structure and of each individual element. Standards, which started as application guidelines given by the manufacturers, are available in the market since the 1980s and are constantly adapted to the current developments in various technical committees. Differentiations are made between: Manufactures application guidelines, case studies or published articles Test standards for the laboratory to guideline the testing procedures (air temperature, type of test equipment, dimensions, test speed, test duration, concentration, type of liquids, monitoring, tolerances, interpretation of results, documentation, etc.), developed by committees based on material and laboratory experts Application standards, which include test standards but also the related minimum performance requirements (values) for material, processing, and quality assurance (practical tolerances), developed by committees based on a wide range of experts (e.g., designers, construction companies, applicators, manufactures, owners, test institutes, quality engineers) and therefore also based on a wide field of experience, different views and up-dated case studies. In the following there are some examples of guidelines and published information’s, ranked according to the year of issue, which are relevant for the development of waterproofing specifications in the tunnel industry:

Jun 13, 2023

By M. J. Gula, S. S. Xue, E. P. Horwitz

A study was conducted to remove iron from sulfate solu¬tions using Eichrom'sDipex®extractant, PP'-di(2-ethylhexyl) methanediphosphonic acid (H2DEH[MDP]). It was found that this extractant can effectively and selectively extract ferric ion from highly acidic solutions. Ninety-nine percent of the iron was extracted from a simulated feed solution in a single stage. The separation factor, Fe/Zn, was 106. More than 90% of the iron in a loaded organic can be recovered in an aqueous solution by reductive stripping. This paper presents the experimental results. A new process for iron removal using Dipex extractant is described and discussed.

Jan 1, 2000

By F. W. Petersen

Slurry reactors are being used extensively throughout the chemical, biochemical and mineral processing industries. This paper describes the interaction between fine ore particles and granular porous adsorbents such as activated carbon and ion-exchange resins in a stirred tank reactor. Gold and silver cyanides were used as adsorbates to detect changes in the mass transfer characteristics of the adsorbents, which were ashed to determine the loading of ore particles. A simple kinetic model incorporating film diffusion, intrapanicle diffusion ~d the adsorption equilibrium, was used to interpret kinetic data and to estimate the effect of slurry conditions on the diffusion parameters. It was observed that the equilibrium loading of fines in the adsorbents was independent of their concentration in the slurry. Furthermore, the presence of these panicles inside an adsorbent decreases the effective diffusion of gold or silver cyanides into the adsorbent matrix. When fine suspended solids are present in the reactor, a decrease in the effective availability of the superficial surface of the pre-saturated adsorbent panicles for mass transfer from the liquid phase was observed. This newly defined surface availability factor was dependent on the concentration, panicle size, and the zeta potential of the fine particles in suspension.

Jan 1, 1993

By M. C. Fuerstenau

A number of interesting and. important phenomena were revealed during a study of the response of beryl to sulfonate flotation (1). Perhaps the most important observation is the effect of various cations on flotation response. Experiments showed that in the vicinity of pH = 3. 0, about three ppm Fe.+++ increased recovery of leached beryl from about 60 to 100 per cent, whereas about four ppm Ca++ reduced the recovery from 60 to 2 per cent. With the exception of ferric iron, all of the other cations investigated reduced flotation recoveries drastically at this pH. As postulated in the paper "Sulfonate Flotation of Beryl", (1) even with low concentrations of polyvalent cations and sulfonate (on the order of one ppm), cation¬ sulfonates are precipitated immediately in solution. That is, blueish-white clouds .were noted to form after given additions of salts to. known solutions of sulfonate. Furthermore, it was also shown that one-hundred-fold more ferric iron than necessary to form the precipitated cloud had to be added to effect complete flotation. In other words, some form of solid ferric sulfonate was found to function as the collector in these systems. The form of the compound was suggested to be Fe (RSC3)2OH and that bonding to the surface occurs through the hydrogen of the hydroxyl. As the form of this compound was shown to be dependent on the extent of hydrolysis of ferric iron, it is to be expected that ferric iron will be unique in some pH region. Further, if the presence of hydroxyl in the neutral precipitated compound is of primary importance, then other cations should function similarly but at different values of pH, since they will hydrolyze at different concentrations of hydroxyl ion. To determine whether the premise of hydrolysis is correct, the study was extended to quartz systems lit the presence of various cations at various values of pH.

Jan 1, 1964

By A. Juganda, F. WILSON, G.E. BOGIN, H. PINHEIRO, N. SANDOVAL, J.F. BRUNE

To evaluate methane explosion hazards in underground longwall coal mines, researchers at the Colorado School of Mines developed a computational fluid dynamics (CFD) model along with a 1/40th-scale, optically accessible, physical model of a longwall mining section. In this project, CFD models assisted in the design of the physical model to ensure specifications were met to accurately represent the scaling physics as well as to assist in narrowing the experimental matrix and identifying key locations for sensor placement to measure velocity, pressure and gas concentrations. This research will help develop strategies for methane monitoring to prevent methane ignitions and explosions in longwall coal operations.

Dec 1, 2022

By L. J. Blatnica

Throughout the 1980's the tem Mine-Wide Monitoring System has had various meanings for manufacturers of these systems and underground mine operators alike. System suppliers had visions of grandeur in the early 80's as they envisioned each mine, that has more than a single section, installing a computer based monitoring system to provide surveillance, control and documentation of the entire mining operation, including everything from a single heat detector to the weekly payroll. In a few cases this may have become reality but the truth is these systems have quietly become a steady but unspectacular workbase for the modern mining industry of the 1990's. As it exists today the total market for underground monitoring systems may not exceed $10 million annually. Suppliers have lowered their expectations of the dollar value of this particular market. Some were entering a new market because of experience with computer based data acquisition systems. Others had been active in the mining industry for years with more traditional equipment (communication systems, methane monitors, safety equipment, etc.) and decided to become involved with Mine-Wide Monitoring Systems.

Jan 1, 1990

By Richard Emberley, Timothy Shaw, José L. Torero, Jurij Karlovsek, Timothy Gibson

"Tunnel closures are highly undesirable and the lengthiest are generally attributed to structural failures (e.g. Mont Blanc). Although historical data shows structural failures are closely linked to fire, design parameters for tunnel safety are not well defined. Current research has focused on defining the fire heat release rate and temperature, but these parameters cannot be easily used to determined structural performance. The energy transferred to the structure, the heat flux, is required but current literature lacks these values. Full scale experiments were undertaken on passenger vehicles resulting in heat fluxes between 20-70kW/m2. Analysis shows a vehicle fire’s duration is closely linked to its mass. Further analysis shows small vehicle fires can be scaled as a function of the tunnel diameter and the characteristic height of the desired vehicle. The present work provides engineers an appropriate design methodology to undertake informed thermal-structural analysis to minimize the risk of tunnel structural failure.INTRODUCTION Quantifying the effects of a tunnel fire depends on many factors such as the type of occupants, their vehicles and spacing, ventilation conditions and the geometric shape of the tunnel (Ingason and Lonnermark 2011). For design engineers investigating the thermal-structural performance of a tunnel, these factors are typically converted into spatial and temporal temperature distributions (Usmani et al. 2001) using various design curves such as those of ISO834-1, Hydrocarbon, Rijkswaterstaat (RWS) or RABT-ZTV (Promat 2013). However, to define a temperature profile through a structural element these curves require a heat transfer model that incorporates an appropriate boundary condition. The appropriate boundary condition is the net heat flux which is the result of a complex energy balance. For use in heat transfer calculations the net heat flux must account for the tunnel geometry as well as thermal properties of a given structural element and all other surfaces and mediums affecting the transfer of heat (Torero 2014)."

Jan 1, 2016

By William Hodder, Ehsan Alavi, Nader Ghasempour, Daniel Cressman

The Don River & Central Waterfront Coxwell Sanitary Bypass Tunnel (CBT) Project in Toronto will extend approximately 10.5 km from Ashbridges Bay Treatment Plant west under Lake Shore Boulevard, north under Bayview Avenue and east through the Don River park area to the Coxwell Ravine Park. The tunnel is currently being mined by using a shielded dual-mode tunnel boring machine (open and close) capable of operating in EPB mode and lined by using a precast concrete segmental tunnel linear with an internal diameter of 6,300 mm and external diameter of 6,900 mm. The CBT is expected to be excavated mainly through shale bedrock of the Georgian Bay Formation, at approximately 50 meters deep. The tunnel crosses a buried bedrock valley in two locations, in the southern portion of the alignment, adjacent to the Don River, and at the northern portion of the alignment approaching the CX-1 shaft. In these two locations, the bedrock cover is expected to be less than 6 meters. The risk of encountering weathered bedrock, significant ground water inflows or surficial soil deposits through these buried valleys was identified during the design phase. The contract required the TBM to be designed with the ability to probe drill ahead of the TBM and convert to EPB mode if necessary, to cross this area. This paper will discuss the additional exploration that was performed by the contractor to identify the extent of this buried valley, the plan going into the zone of potential weathered shale, and the actual conditions encountered.

Jun 13, 2021

By Gary B. Glass

In 1997, 92.3% or 235.7 Mt (259.8 million st) of coal produced in Wyoming came from the Wyodak coal zone in the eastern Powder River coalfield. The mined portions of the zone consist of one to three beds of coal with an aggregate thickness between 15 and 33.5 m (50 and 110 ft). The thickest expression is 61 m (200 ft). The delivered coal from this zone averages 0.33% sulfur, 5.12% ash and 19.98 MJ/kg (8,590 Btu/lb.). This coal zone occurs at or near the top of the Paleocene Fort Union Formation, which is overlain by the Eocene Wasatch Formation. There is also production from two coalbeds in the lower portion of the Wasatch at the southern end of the basin. Production of coalbed methane derived from the Wyodak coal zone is currently an estimated 289 Mm3/a (10.2 billion cu ft/year). This production is occurring west and downdip from the coal mines and is increasing each year.

Jan 1, 1998

By Roland Arnold, Richard Gradnik, Martin Zeindl

This paper presents the details of the Kramer tunnel project in the Federal State of Bavaria, Germany. This road tunnel, which has been under construction since December 2019, is the key component of the western bypass of the town of GarmischPartenkirchen. Once completed, it will relieve the town’s central district from enormous volumes of traffic. The contractor is the joint venture named ARGE Kramertunnel consisting of BeMo Tunnelling and Subterra. The whole project will be completed and handed over to the project owner, Staatliches Bauamt Weilheim, in 2023. The opening of the entire bypass section including the tunnel to traffic is planned for 2024. The tunnel, with a total length of 3,609 m (2.24 miles) and an estimated cost of EUR 178 million (incl. VAT), is designed as a single-tube, double-lane structure with one traffic lane for each direction of travel. The safety issue that exists for single-tube tunnels is solved by a parallel escape tunnel passable for vehicles. All tunnels and ducts are excavated according to the principles of the New Austrian Tunnelling Method (NATM). In order to reduce the geological risk for the owner, the escape tunnel was supposed to be completed before the design process for the main tunnel ever began. The exploratory tunnel was awarded to a competitor with an separate contract.

Jun 13, 2021

By Fred Morelko, Michael Connelly, Brad L. Ricks

INTRODUCTION The $1.1 billion Bajo la Alumbrera Project, started up in 1997 by Minera Alumbrera Limited in the Catamarca Province of Northwestern Argentina, is the first large scale modern mining project to be developed in Argentina. Like many modern Andean mining projects, existing infrastructure was not available to economically transport the 875,000 tonnes of product per year. A variety of alternatives were investigated, including upgrading of existing roads and railroads, slurry pipelines, and combinations of these systems. The final system selected was to combine a 312 km slurry pipeline with an 820 km rail haul to a ship loading facility near Rosario. The concentrate pipeline crosses divergent terrain between the minesite at 2400 m elevation and the filter plant at 400 m elevation. The system selected represented the lowest net present cost alternative by a significant margin. BACKGROUND The Bajo Alumbrera deposit was discovered in 1947 by Professor Cetioni from the University of Tucuman. It is a large (>750 million tonnes) medium-grade (0.6%) copper deposit with high gold values (0.5 g/t*). The deposit outcrops, making it very suitable to modern, large scale, open pit mining techniques using 218 t trucks and 43 m3 shovels. Advances in gravity concentration of the gold helped to demonstrate the feasibility of the project in a study prepared by Fluor Daniel for Minera Alumbrera in 1994. The initial concentrator is the largest green-field concentrator ever constructed, rated at 85,000 t/d. Production will peak at 190,000 tonnes of copper metal and 710,000 troy ounces of gold per year, one of the top 10 copper and top 15 gold producers in the world. * Throughout this paper, the word tonne and abbreviation refer to the metric ton of 1000 kg.

Jan 1, 1998

By Donald E. Zipperian

The studies described in this paper have established that flotation conducted in a column cell provided with gas generation by aspiration into surface tension lowered water, may considerably increase the efficiency and particle size range of a flotation process. Operation of a DEISTER FLOTAIRE ® Cell at several Southwest United States flotation plants under continuous rougher, scavenger and cleaner conditions has demonstrated the main positive features to be: (a) higher capacity per unit volume than conventional flotation equipment, (b) improvement of flotation of plus 0.210 m particles, (c) improved flotation of particles minus 0.037 m.

Jan 1, 1984

By Stephen J. Swan

Feed-forward control (i.e. the forward flow of information in a control system ) is a simple and flexible approach to over-all control of a ball mill-rake classifier grinding circuit. The system described here uses mill power, feed rate, mill dilution water flow rate, and classifier dilution water flow rate only, to control mill load, throughput, mill solids, and classifier solids as well as classifier overflow grind. The mill load is controlled by a simple feed-back control loop, while mill solids and overflow grind are controlled within close limits by a unique non-linear feed-forward water control system. In effect the control follows a limited mathematical model of the grinding circuit. The configuration minimizes deviations in overflow grind due to changing ore conditions, but since it is open-loop, and the model is not complete, it is affected by changes in total ball charge and liner wear. These effects are fortunately gradual, and changes in the grind can usually be kept to within ± 1% of a target continuously for several days without adjustment. Control adjustments are made with feed-back from laboratory composites. This control system has won enthusiastic operator acceptance; it is easily started up and shut down; grind-outs have been eliminated along with flotation machine flooding and mill spills. Standard measurements and components are used throughout providing a trouble-free system design at a moderate cost.

Jan 1, 1970

By Arthur W. T. Grimley

Hydraulic coal mining is being successfully practiced in China, U.S.S.R., Japan and Canada and in each country, excepting Japan where suitable sites are not available, the system is being expanded to either existing conventional mines or new mines. Productivity levels and economics at these mines are in all cases better than the productivities achieved in conventional mines in the same general localities. In the U.S.S.R. face productivities approaching 50 tons per man shift have been reported while in Canada the latest statistics show average face area productivity levels are in the region of 200 tons per man shift production monitor. In the United States hydraulic mining has not been actively pursued to the same degree and consequently there are no full scale hydraulic coal mines in operation or construction. Because many of the coal measures in the Western U.S.A. are generally somewhat similar to those being successfully hydraulic mined in Western Canada and parts of Siberia it is realistic to believe that successful hydraulic mines can be designed and developed in the Western U.S.A. Particularly if the vast technological base that already exists is used to improve on other people's ideas, systems, methods and equipment.

Jan 1, 1983

By McDonald E. Wrenn, Narayani P. Singh, Victor E. Archer, Ceno Saccomanno

Fourteen uranium miners' lungs from Colorado plateau were collected at autopsy and the concentrations of 238U, 234U and 230Th were determined by radiochemical procedures utilizing solvent extraction - alpha spectrometric techniques. The uranium and thorium isotopes are in near equilibrium with average concentrations of 238U, 234U and 230Th being 89.3, 95.2 and 91.1 pCi/kg respectively. The combined average radiation dose rate to lung from these three isotopes is about 24.2 mrad/year at death excluding the unmeasured contribution from the 226Ra and daughters. The average concentration of 230Th is about 65 times higher than the mean concentration of 230Th in lungs of non-miners dying at comparable ages from the same region.

Jan 1, 1981

By J. Weinstein

New erosion, corrosion resistant metal, ceramic, and polymer composite technologies are being developed and marketed by Alanx Products L.P. for use in hydrocyclones, pumps, valves, and other applications in mining and minerals processing. This paper will present an overview of the ceramic/metal composite material system and properties developed, which include excellent erosion/ corrosion resistance. Wear data will be shown from a variety of laboratory tests in dry and wet conditions, in aqueous neutral and corrosive environments. Comparisons will be made with a variety of competitive materials currently used in the industries sited. Data will also be presented on field tests with pumps and hydrocyclones in hard rock mining and other abrasive/corrosive environments. Field data from North and South America, as well as Australian mining applications will be highlighted.

Jan 1, 1992

By Greg Sanders, Bill Lueck, Michael Gilbert, Mahmood Khwaja

"The city of Minneapolis contracted with CDM Smith to update and provide a conceptual design for improvements to mitigate surcharge flooding in the Central City Storm Water Tunnel System (CCSTS). As a part of the project, CDM Smith conducted a field survey and condition assessment of the existing tunnel system. Information from the survey was then used to update the existing XPSWMM model and develop system wide alternatives.The CCSTS provides storm-water runoff drainage for nearly the entire area of the city’s downtown commercial district. The system consists of deep storm-water tunnels constructed in the St. Peter Sandstone, approximately 21 m (70 ft) below the street’s surface. The primary tunnels comprising the Central City storm water tunnel system are located below Hennepin Avenue, Nicollet Mall, Lesalle Avenue, Marquette Avenue South, 2nd Avenue South, South 5th Street, Washington Avenue South, Portland Avenue South, 2nd Street South, and Chicago Avenue South, as shown in Fig. 1. This network of tunnels conveys the runoff from a 305-acre tributary area that is generally bound by Hennepin Avenue and 1st Avenue North to the east, 12th Street to the south, 4th Avenue South and 7th Avenue South to the west, and 2nd Street South. These tunnels were constructed between 1936 and 1940, except for the Marquette Avenue South tunnel, which was constructed between 1963 and 1964.The CCSTS operates as a gravity flow system. These tunnels were constructed within the St. Peter Sandstone layer of bedrock and emerge from the bedrock at the Mississippi River below St. Anthony Falls. The Central City and the adjacent Chicago Avenue tunnel system converge into a single outfall at the Mississippi River. The runoff discharges from the converged outfall to a side channel of the Mississippi River, called a tailrace, located near the Guthrie Theater. The Minneapolis Division of Surface Water and Sewers provided 32 historic plats detailing the plan and profile of the tunnel system.The tunnel plans show nine different cross-section configurations. Eight configurations within the overall system generally show the same geometric “cathedral” shape with the inside dimensions varying from 1.2 to 1.8 m (4 to 6 ft) in width and 1.8 to 2.4 m (6 to 8 ft) in height. For analysis, these eight configurations were reduced to three configurations with regards to tunnel liner, cross-sectional area and support. For simplicity, the three configurations are described according to the three types of tunnel support used during construction: none required, light timber and heavy timber"

Jun 1, 2019

By Timothy O’Rourke, Karrie Buxton, Chris Lynagh, Daniel Dobbels, Frederick Vincent

The Doan Valley Storage Tunnel Project in Cleveland Ohio was constructed to control Combined Sewer Overflows (CSOs). It is a complex system of three tunnels ranging from 8.5 to 18 feet in diameter with a total length of about 2.3 miles that was put into operation in mid-2021. The project lies within and below the cultural, educational, and medical hub of Cleveland, which presented unique design and construction challenges. This paper provides a case history of the design and construction, with particular attention given to lessons learned in devising a large tunnel system that can carry both dry and wet weather flows constructed in rock with limited cover, within a flood plain area and vibrant urban center

Dec 1, 2022