Search Documents

By H. Sevim

In this paper, the research effort in simulating the operation of underground coarse-coal hydrotransport systems (UCCHS) is summarized. The equipment of the system to be simulated is already optimally selected by using an analytical optimization model. The purpose of the simulation model is to test the performance of the system and to obtain the distribution of the operating parameters such as water and power consumption, amount of slurry delivered to the preparation plant, etc. Knowledge of the distribution of these parameters is essential for the efficiency of the design and the operation of the system.

Jan 1, 1985

By Anup Tiwari, Khanindra Pathak, BIBHUTI BHUSAN MANDAL

Failure of in-pit overburden dumps in open-pit coal mines causes debris to flow toward the active working face, threatening the safety of people and equipment. The evaluation of the potential mobility of failing mass will aid in hazard mitigation associated with unwarranted dump failure. The potential mobility is shown by mobility ratio (ratio of total drop between debris flow's initial and final deposition points to total travel distance) and runout characteristics. In light of above, a laboratoryscale debris flow flume was developed to investigate the effect of material gradation and slope angle on runout characteristics and mobility ratio. The total mass of experimental debris mix (Q) is fixed at 30 kg with 20% water content. Experiments at three different slope angles (30°, 35°, and 40°) demonstrate that increasing the proportion of fines in the experimental mix increases runout characteristics while decreasing the mobility ratio. The length and area of the runout decrease as the slope angle increases, while the mobility ratio increases. There is a positive correlation between d50 and runout characteristics at a fines content of 0.1Q, but a negative correlation at a fines content of 0.2Q and 0.3Q. Conversely, there is a negative correlation between d50 and mobility ratio for fines content of 0.1Q, but a positive correlation exists for fines content of 0.2Q and 0.3Q. A new index called the fine-to-coarse (F/C) ratio is used to identify the critical value of fines and coarse proportion that causes a transition from dry granular flow to fluidized debris flow.

May 29, 2023

By Congcong Chen, Bo Ma

When assessing the safety of a tailings dam, the constant weight method (CWM) is one of the most commonly used methods. However, when the evaluation indicator value suggests serious defects, the evaluation value is often inconsistent with the actual situation. To address this issue, the variable weight method (VWM) is introduced to assess the safety of the tailings dam. Initially, a three-layer indicator system for dam failure safety assessment is built, and individual indicator values are divided into four grades. Then, an appropriate state variable weight function is constructed and relevant parameters are determined. Finally, a case study is illustrated to verify the effectiveness of the model. The assessment results of the VWM more closely represent the actual situation than that of the CWM, which is more helpful for decision makers and technicians to take scientific and reasonable precautionary measures, thereby improving the safety management of the tailings pond.

Oct 8, 2022

By M. I. Al-Wakeel

Nile sediment was collected as a waste from one of the water treatment plants in Cairo, and subjected to petrographical investigation and granulometric, chemical, and mineralogical analyses. It was expected to find diatomite in that sediment but it was a surprise to find that the diatomite content amounted to about 52.01% by volume in addition to quartz, orthoclase and clay minerals. The latter are represented by montmorillonite and illite minerals. The sediment is light gray in color, soft and has low density and high surface area, such density and surface area generally decrease with temperature. The sediment absorbs 317% of its weight in water. The diatomite skeletons are the main factor responsible for its high porosity producing microporosity and low density, and these particles are concentrated in the very fine silt size fraction (11x2µm). The common diatoms in such sediment include Cyclotella ocellata Pant, and Melosira granulata (Ehr.) Ralfs. It seems that this Nile diatomaceous sediment has many advantages over the fossil diatomite, such as Fayium diatomite in Egypt, with the absence of carbonate minerals that require grinding and calcination those cause destruction of the cellular structure and energy consumption. This Nile diatomaceous sediment can be processed using sequential classification to obtain diatomite concentrate of 88.8% grade at 90.6% recovery, and a middling product of 19.4% grade and 5.8% recovery. The suggested flow sheet is quite simple to produce diatomite product for different industries at a low cost. The unusual particulate structure and chemical inertness make diatomite an ideal mineral to be used as functional filler in a wide range of industries, and as catalyst carriers and insulating material. Key words: Egypt, Nile sediment, Diatomite, Beneficiation, Sedimentation, Classification.

Jan 1, 2008

By W. K. Katoto

The Tailings Leach Plant (TLP) of the Zambia Consolidated Copper Mines Ltd at Nchanga was commissioned in 1974 as the world's first largest successfully operated agitation leach SX-EW plant for copper production. The design, development and operation of the plant soon after commissioning termed as TLP stage II has been described by Holmes et al (1). In the initial phase the plant was designed to treat approximately 25,000 tonnes per day of current flotation tailings from the Nchanga Concentrator operations, and had a design capacity to produce 75,000 tonnes per annum of copper. Further expansion took place in 1986, and TLP stage III was successfully commissioned to treat an additional 20,000 -25,000 tonnes per day of large reserves (over 135m tonnes) of reclaimed tailings stockpiled since the early 1930's in four paddock type tailings dams (T01 to T04). The salient feature of TLP stage III expansion described by S K Mwenechanya et al (2 -3) was the installation of the world's largest Horizontal Belt Filter Plant with 26 filters each of 80 m2 filtration area.

Jan 1, 1996

By S. P. Lewis, R. L. Sundeen

Most of us are aware of the ever increasing use of underground space. At the Advisory Conference on tunneling in Washington, D. C. in June of 1970, the demand for construction oriented tunneling during the 1970s was estimated at some 21,000 Km of length with an excavation volume of 675 million cubic meters. Of this total, 11 million cubic meters were forecast for underground parking. Though this is a small portion of the total, it is significant to note it represents a 280% increase over the previous decade. Other areas of unusual increase were railroad tunnels, 150%, and rapid transit tunnels, 160% (1). Faced with this increasing demand, the need for improved excavating efficiency is obvious. Great strides have been made. In Japan, for example, several new long tunnels have been driven parallel to old existing ones at costs as much as 50; under those of the original tunnels (1). This is an impressive achievement. I am certain, however, that we would all agree that even greater improvement is required. Great emphasis is being placed upon sophisticated systems which include among others, mechanical borers, thermal fracturing, and various methods of rock weakening and softening. However, in hard rock excavation the fact remains that the drill-blast method continues to be the most widely used system. Undoubtedly it will continue to be one of the most important techniques in the forseeable future.

Jan 1, 1974

P&H MinePro Services Canada is supplying Syncrude Canada three more of its model4100BOSS electric mining shovels. The shovels will be delivered during 2003. Syncrude’s oil sands operations already use five P&H shovels. The first 4100BOSS shovel was commissioned at Syncrude’s operation in northern Alberta, Canada in October 2001. The unit loads more than 9 kt/hr (10,000 stph) of unblasted oil sands. Since it began operation, the 4100BOSS has shown a 28% production increase over the four P&H 4100TS shovels also on site.

Jan 1, 2003

By Fred Pena

Cyprus Pima Mining Company is located in the Mineral Hill District of southern Arizona, approximately 22 miles south-southeast of Tucson. Cyprus Pima Mining Company is owned 50.01% by Cyprus Mines Corporation, 24.99% by Utah International Incorporated, and 25% by Union Oil Company of California, with Cyprus having the management responsibility. Cyprus Pima's history has been one of continued expansion from an initial plant of 3,000 TPD in 1957; 6,000 TPD in 1963; 18,000 TPD in 1966; 36,000 TPD in 1967; and 53,500 TPD in 1972. The major reason for Expansion IV was that a large volume of low-grade ore had to be moved to get at a higher grade ore in the course of proper pit development. With mining costs already defrayed, this relatively hard, low-grade material became economically profitable for subsequent milling and concentrating treatment. Similar material previously stockpiled was available for ore treatment. In an effort to meet the continuing search for lower unit costs, the largest milling and concentrating equipment had to be examined. The management of Cyprus Pima Mining Company began investigating autogenous, and semi-autogenous milling in 1964 when two carloads of ore selected from the Cyprus Pima pit were sent to the Koppers--Hardinge Operation at York, Pennsylvania for testing. One car contained approximately 40 tons of hard arkosite and the other contained approximately 40 tons of ore classified as soft Hornfels. The purpose of the testing was to determine the amenability of both ore types to autogenous or semi-autogenous grinding.

Jan 1, 1974

By B. Law, M. Menabde, B. Baird

Blasor is a new mine planning tool which is being used in the long and medium-term optimization of multi-open-pit operations throughout BHP Billiton’s Base Metals and bulk commodities portfolio. It is not just a scheduler, nor even only a schedule optimizer—although this function lies at the heart of the tool’s functionality—but a pit development plan optimizer, used from ultimate pit design and process plant capacity sizing right through to mining phase design and optimal panel scheduling. The tool uses a mixed-integer-linear-programming optimization engine to determine when material should be excavated and where it should be sent to optimize discounted operating cash flow over the life of operation. The core software design concept of Blasor is to provide a tool which is intuitive and flexible enough so that a competent mine planner can perform a pit development plan optimization without assistance from optimization specialists. To this end, a generalized graphical user interface has been implemented which allows full configuration of the optimization problem, including the definition of all inputs and constraints, specification of the material flow topology, bin and destination class definitions and full specification of the economic model encompassing prices and costs. This paper describes the capability of Blasor and outlines the design concepts underlying its design philosophy.

Jan 1, 2007

By Mostafa Benzaazoua, Bruno Bussière, Mukendi Kongolo

The desulphurization process has been proposed over the last few years for acid mine drainage control at certain mines, which generate low to medium grade sulphidic tailings (-3 to +25 wt% S). The environmental sulphur recovery, which means the sulphur to be floated to produce a non-acid generating final tailings, depends mainly on the intrinsic neutralizing potential of the tailings. However, in some cases the sulphur cleaning is complicated by other parameters which affect the flotation probability of the sulphide particles. In this study, a number of tests were conducted with a Hallimond tube and Denver Cell on both pure mineral and mine tailings. To develop a better understanding of the mechanisms of non-selective sulphide flotation, three types of approach were investigated in this work: (i) pure pyrite at progressive milling degrees, (ii) artificial mix of pyrite and quartz at different calibrated granulometry and (iii) same composition tailings with 26 % wt sulphur at progressive milling degrees. The effect of the granulometry on the sulphide flotation was demonstrated both. The results allow us to define a granulometry model, which can then be considered in the whole desulphurization modeling.

Jan 1, 2000

By Ahmet Tezcan, Zeki M. Dogan, Yalçin Kaytaz

Autogenous grinding in Turkey was first applied to quartzite where the mill is grate discharge type with an internal diameter of 2.99 m, having a length of 3.20 m and a capacity of as to 11.0 tons per hour. The second autogenous grinding was applied to a copper ore at Murgul Cakmakkaya Flotation plant of (KBI) Black Sea Copper Works having three mills 26 feet in diameter and 10 feet in length in close circuit with hydrocyclones. Recently, alterations were made in grinding circust by adding pebble mills. Furthermore, rubber liners and lifter bars were introduced pebble extractor and classifier were new features in the primary mills and circulating load was reduced by 20-50 tons per hour. At the end of these charges, capacity of each mill line was increased to 48 tons per hour with a full capacity of more than 9000 tons per day. Thirdly, autogenous grinding has been executed successfully on the slags of Samsun Smelting Plant of (KBI) Black Sea Copper Works with a mill of 20 feet in diameter and 6 feet on length having pebble mill following autogenous grinding.

Jan 1, 1992

By J. G. Groppo, A. E. Bland, B. K. Parekh, W. F. Stotts

Many coal preparation plants discard fine coal (generally minus 100 mesh) because it is difficult to beneficiate economically. At the Kentucky Energy Cabinet Laboratory (KECL), the waste streams from several Kentucky preparation plants were evaluated for cleaning with counter-current column flotation. A series of performance evaluations were conducted using a 0.05 m (2 in.) internal diameter (I.D.) 7.9 m (26 ft.) high laboratory column. The objectives of these tests were to assess the performance in terms of recovery and percent ash in clean coal and to optimize the operating parameters relative to combustible recovery and grade. Refuse streams containing 30-50 percent ash were upgraded to 2-8 percent ash with Btu recoveries of nearly 90 percent. A pilot scale column flotation cell was installed at the Bell County Coal preparation plant. This pilot plant utilized a 5.79 m (19 ft.) high and 0.15 m (6 in.) I.D. column to verify the performance data of the 0.05 m (2 in.) I.D. column for two different waste streams. Performance evaluation and pilot plant testing results related to scale-up are discussed.

Jan 1, 1988

By V. E. May

Has your organization adopted Six Sigma as part of their Performance Improvement strategy? What about Lean manufacturing or Lean Six Sigma? If you already have any of these business process improvements in place where will you go next? In this article we will focus on transforming your organization beyond Lean Six Sigma to the next level of performance. In the future companies can take another quantum step forward by combining Lean Six Sigma with advanced Root Cause Analysis (RCA). The value of taking this natural progression on the way to achieving new levels of organizational excellence is presented.

Jan 1, 2011

By Paul Russell, M. M. Kimberley, Erick F. Welland, Louis Cope, C. C. Mosher, William M. Shepard, William C. Larson, Graham Closs

Exploration activities in 1980 felt the effects of unstable economic conditions and oscillating metal prices. In the cyclical, boom-or-bust precious metals and uranium markets, precious metals activity flourished and uranium was definitely in a slump. By November last year, the price for vellowcake was down nearly $20 from two years earlier. Many mining and milling operations closed, particularly in Wyoming, New Mexico, and Colorado. Decreasing emphasis on nuclear power continued to impact the market, as did the Three Mile Island accident of 1979. Earlier forecasts estimated that 10 to 12 reactors would be ordered per year by US utilities throughout the 1980s, but current forecasts suggest that it may be 1983 or 1984, or even later, before any new US plants are ordered, according to Thomas A. Boyden, vice president of Nuclear Exchange Corp. "Without those new plants, the consumption loss to industry is 4 to 5 million pounds (1.8-2.3 kt) of uranium per year. The cumulative loss to the industry is currently estimated at 25 to 30 million pounds (11.3-13.6 kt)," Boyden said in a May 1980 presenta¬tion. Despite the plunging market, there were a few notable uranium explora¬tion programs: •Exxon expanded uranium exploration in New Mexico, where the company reportedly took preliminary steps toward acquiring mineral rights to a 22-km2 prospect, 19 km south of Santa Fe. • Mountain States Resources began the second phase of an exploratory drilling program on its Sinbad/ Solo prospect in Utah. • Also in Utah, Cotter Corp. drilled its first exploratory hole in the Dirty Devil River district. Exploration for precious metals in 1980, however, appeared to tend toward the opposite extreme. High prices sparked near feverish searches in Alaska, California, Colorado, and Nevada. Numerous mines abandoned years ago were revived with some signs of success. Significant gold finds were reported in California and Nevada: • Homestake Mining Co. announced a gold discovery in California estimated to contain over 5 Mt with an average grade of about 5.8 g/t. Because the deposit consists of finely disseminated particles not visible to the eye, many speculate that prospectors bypassed the area during the 1849 California gold rush. • Newmont Mining Corp. discovered two gold ore bodies-Maggie Creek and Gold Quarry. Maggie Creek reportedly contains an estimated 13.7 t of gold in 4.3 Mt of ore, and Gold Quarry contains about 31.1 t of gold in 9 Mt of low grade ore and 2.3 Mt of higher grade ore. Highlights of this year's exploration review include articles on the modest growth recorded in geophysical activity, technical developments in exploration geochemistry, the variety of new instruments being tested or made available for exploration, and a state-by-state exploration review for the year.

Jan 5, 1981

By T. Karalis

Perlite is a generic term for naturally occurring siliceous rock. It is a form of natural volcanic glass the main constituent of which is amorphous silica (70-76%). Perlite, when heated rapidly to its softening temperature range, expands from four to twenty times its original volume, due to the presence of 2-6% ?combined? water, in a manner similar to popcorn as the H2O molecules vaporize and create countless tiny bubbles, which account for its exceptional physical properties: light weight (30-150 kg/m3), low thermal conductivity, cellular structure, in general. These properties make perlite adaptable for numerous end-uses, which can be distinguished into 2 categories: Expanded perlite applications in: a) Construction Materials market (e.g. Acoustical Tiles, light-weight insulating Mortars, self-levelling Concrete), b) Agriculture (e.g. Hydroponics), c) Food and Chemical industry (e.g. Filtration Media, Filler, etc.), d) Insulation and Heat resistance technology (e.g. Cryogenic vessels, Refractory Bricks, etc.). Unexpanded Graded perlite applications in: a) Phosphoric Fertilizers industry (additive in H3PO4 production), b) Foundry technology (slag-aid, insulating and heat resistance agent).

Jan 1, 2006

By M. Misra, I. A. H. Schneider

The flocculation of -38 pm calcite, hematite and kaolinite aqueous suspensions by the yeast Candida parapsilosis and products derived from rupture of the microorganism was studied. Flocculation of hematite suspensions by the microorganism and its derivatives readily takes place between pH 2.8 and 11.4. Maximum flocculation occurs at about pH 6.5. Flocculation of calcite suspensions by the microorganism and its derivatives readily takes place between pH 7.0 and 11.8. Maximum flocculation occurs at about pH 10.0. Flocculation of kaolinite suspensions was less than that for the other two minerals. However, a soluble fraction derived from the rupture of the organism functioned as a good flocculant for the mineral, albeit at an increased concentration, between pH 2.6 and 11.5. Maximum flocculation occurs between pH 6.8 and 7.2. An attempt is made to relate the behavior of the various systems to the surface characteristics of the minerals and the surface and chemical properties of microorganism and its derivatives. Experimentation used to evaluate the flocculation includes actual flocculation tests, microelectrophoresis measurements and scanning electron microscopy.

Jan 1, 1994

By A. J. MacKellar

The economic viability of any project is generally assessed on an evaluation of the total capital constructed costs along with operating costs, owner's costs and market conditions. This paper will be directed to the role that Cost Engineering plays in the development of the capital costs and the cost control techniques applied thereto.

Jan 1, 1975

By James E. McNulty

The planning and development of new coal mines is requiring the increased use of geologic, geologic engineering and hydrogeologic investigations. This is caused in part by the fact that new mines must deal with less favorable conditions than existing mines as well as higher costs of development and in part by the dictates of regulatory authority. High costs of new mines require greater reliability of geologic assessment using best available geotechnical and geophysical methods and technology. Although the increased cost of additional subsurface data is significant, the more important factor may be the impact on project lead time.

Jan 1, 1981

By Shuie Li, Taibai Li, Tao Hu, Zhongjie Wang, Xiang Ge

As one of the main power sources, lithium-ion batteries (LIBs) will continue to be applied on a large scale in the future market. Commercialized LIBs cathode materials contain various valuable metal elements including Li, Co, and Ni. The development of green and efficient recycling technology is essential. Deep eutectic solvents (DESs) have recently emerged as a new class of green solvents that could potentially be applied for the LIBs recycling industry due to their capability to leach the active materials without the introduction of environmentally hazardous reagents as used in conventional hydrometallurgy process. Considering the rapid progress, a critical review focusing on the progress and fundamentals about the overall efficiency has practical significance for the further advancement of this field. Herein, we briefly introduce the overall process of using DESs for LIBs recycling and specifically focus on the efficiency of each step. Current fundamental understandings and new experimental approaches to enhance the efficiency of the leaching process, the extraction process, and reusability are summarized. We expect this review article to inspire scientists to use DESs as powerful tools for advancing the frontiers of LIBs recycling.

Jul 30, 2022

By D. Brady

When deciding to deploy rescue teams underground the decision makers need to be able to determine that there won?t be an explosion whilst the rescue teams are underground. Previously general body concentrations in areas likely to be travelled were compared to explosive limits on a one off basis with no formal process looking at trends or other areas. A new approach is being adopted that takes into account the rate of change of gas concentrations with triggers set to enable a withdrawal of personnel prior to a possible explosion and influences such a barometric pressure changes. This paper explains the rationale behind the changes made and the advantages and implications of adopting such an approach.

Jan 1, 2012