Search Documents

By Francois E. Heuze

Excavation of large rock caverns is a stepwise process. Whether one uses a heading and bench method or a multiple drift system, the use of excavation steps enables one to introduce the reinforcement, such as bolts or shotcrete, at the earliest possible stage. Knowing the spatial distribution and properties of rock materials and geological discontinuities, the cavern geometry and its reinforcement must be optimized. The finite element method of analysis is a powerful tool for such optimization. However, the models are only as good as their ability to account realistically for the physical attributes of the prototype and for the excavation sequence. They must include the following: - ability to model an incremental construction process. Thus requires the use of "Restart" procedures where displacements and stresses from a previous equilibrium are saved for the next step. - ability to model non-linear rock material behavior; in particular, the post-peak behavior of the rock which retains a residual strength when con-fined. The stability of many under-ground structures rests with the "broken" rock carrying significant loads. - ability to account for the non-linear behavior of geological discontinuities. These are two-fold. First, up to peak, non smooth rock joints will dilate. In a confined situation, dilation will increase joint strength by a consider-able amount (Obert, et al, Brady, 1971, Heuze,1978a), Then, beyond the peak, the joint also retains residual strength.

Jan 1, 1978

By T. B. Acton

There are two types of ore transportation systems in use at Newmont's Magma Copper Co. San Manuel mine in Arizona-rail-mounted, box-type rotary cars and the newer rail-mounted, bottom-dumping ASEA cars. Though the cost per car for the ASEA units greatly exceeds the cost per rotary car, the advantages of the ASEA units, including much faster dump times, have made the ASEA system a successful alternative at the San Manuel mine. The rotary system of ore transportation has been in use at San Manuel since production began in 1956. The system employs 7.9-m3 box-type cars to transport ore by rail to shaft pocket areas. A rotating dumping mechanism turns three cars at a time upside down to empty them, and returns them to an upright position. Trains of 15 cars each are dumped in about six minutes. Each 15-car train is pulled by an 18-t rated trolley locomotive. There are about 400 rotary cars in service at San Manuel and the system is used for the majority of ore haulage. This well-proven rotary method was instrumental in achieving the December 1977 world record of 272 Mt hoisted from an underground copper mine. Magma Copper Co. began using ASEA cars in late 1977. Designed by ASEA of Sweden, the cars are built for San Manuel by Kasper-Hall Manufacturing Co. in Tucson. The cars basic design feature is a hinged floor that opens at the side as the car is pulled through the dump. As it passes over the dump, a fifth wheel attached to the hinged floor (opposite the hinges) travels along a rail in the dump. This rail dips down into the pocket and then returns to track level. As the fifth wheel travels along the rail, the car floor opens, the car dumps, and the floor is then returned to track level. As the car is dumping, the body remains suspended over the pocket by wheel rollers attached to each side of the dump. Trains of 10 cars each are emptied in about 45-50 seconds. Each ASEA train is pulled by an 18-t rated trolley locomotive, adapted at San Manuel to allow it to pass through the ASEA dump. At minimal cost, "wings" are welded to each side of the locomotive. These wings suspend the locomotive over the pocket as the train passes through the dump. Advantages of the ASEA System Major design characteristics of the ASEA and rotary systems are shown in the accompanying table. The comparison points out some of the following advantages demonstrated by the ASEA system. • Faster dumping-An ASEA train dumps in 50 seconds, while a rotary train takes at least six minutes. There is no stopping or starting when dumping an ASEA train. The train enters the dump area, dumps, and leaves in one continuous motion-in contrast to rotary trains which must stop and start five times to dump. With the rotary system, three cars are spotted in the dump mechanism by remote control. When the cars are in place, the train operator activates the dump, the cars are turned over, and then returned to an upright position. This process is repeated until all 15 cars in the train are emptied.

Jan 4, 1980

Ten years ago, only 3% of Consol's underground coal production resulted from using the longwall mining method. Today, that figure has grown to 45% and has helped the Pittsburgh-based concern fuel an upswing in productivity. The company reported that productivity at its underground mines, excluding labor strike periods, increased 24% between 1978 and 1981. Last year, an additional 8% increase was achieved. Efforts such as improved safety, training, engineering, and maintenance programs as well as the closing of unproductive mines has contributed to these gains, according to Joseph M. Richards, Consol's executive vice president of operations. But, Richards adds, a great part of the credit goes to longwall mining. What is Longwall Mining? To fully appreciate the advantages of longwall, one needs an understanding of how mining is done by other methods. For instance, in both conventional and continuous mining, rooms or tunnels are dug in the coal seam. Pillars of coal are left standing to support the roof as mining moves forward in the seam. In conventional mining, a slot is cut in the base of the seam and holes for blasting are drilled. After blasting, the coal is loaded. A more efficient method - continuous mining - uses a machine that combines cutting and loading. Longwall mining, by contrast, works backwards from the end of a panel. Two parallel sets of tunnels (development panels) are cut into a seam with continuous mining machines, then connected with a set of crosscuts at the far end. Min¬ing then proceeds back toward the entrance. Longwall mining employs some very productive machines. Large drum shearers, for example, run on a track along the length of the coal face for some 150-180 m (500-600 ft). The shearers cut the coal which falls onto a conveyor system or pan that also runs the entire length of the face. The longwall crew works under a roof of heavy steel supports called shields. As the coal is removed, shearers, pans, and shields are moved forward by hydraulic rams. The roof is allowed to collapse behind the shields. In addition to increasing production, longwall mining is considered to be safer because the miners work under strong steel shields. New designs have made them more rugged and maintenance free, as well as more stable on soft mine floors. Early roof supports, called chocks, had gaps in the roof canopies. The new roof shields now cover the entire working area and are better able to prevent roof material from falling into the working area, thereby improving safety and productivity. Longwall mining also results in a cleaner product in many mines. If the first layer of rock over the coal seam is thin, it might have to be removed with the coal in a room-and-pillar operation so a

Jan 11, 1983

By J. P. Kennedy, O. A. Bascur

Large metallurgical complexes have more data than a small city and these data change as internal and external conditions evolve. Staffing turnover hinders experienced-based decisions especially with simple tools like spreadsheets. Lack of current information can contribute to decisions that result in significant deterioration in the quality of operation. Timely, unified information from sophisticated analyses presented to the broadest possible reach will improve operation. The major innovation is the addition of the web browser to the suite of software people will use with no training – the other two are spreadsheets and graphical presentations – and the consistent organization and transformation of the real time data to support broad access. This paper describes the data transformations and presentation methods necessary for a Web view, especially the special needs of real time data and analysis required for active operations decision-making. Many people inside and outside the complex, not just operators, need timely information that is abstracted, aggregated, organized and unified. Unification and aggregation of real time data presented via the Web opens a new paradigm for collaboration. The analysis tools are as important as the data. These rule-based tools add significantly to the operations database in the form of results stored for viewing with plant data. Mining and metallurgical plants already use many sophisticated analysis tools such as predictive maintenance policies based on statistical analysis vibration analysis, and oil and lube analysis for critical equipment. These add real time events, similar to an alarm package, and unified production information to the operational database. Simple models are used on line to create key indices that provide a real time indication of performance. Key indices include metrics for losses due to plant availability, performance efficiency, and overall process equipment effectiveness. These additional data in the operations database are used for early fault detection, increased production, better quality, higher availability of equipment and faster detection of process bottlenecks. An important feature is the ability for people to create their own key indices and store the results for use by anyone in the plant historian, but accessible by a browser. Keywords: plant information, principle components analysis, data reconciliation, gross error estimation, Internet, Word Wide Web

Jan 1, 2002

By M. K. Larson

Proper employment of numerical stress analysis design tools is based on the demonstrated ability of a model to capture key elements of the geologic site model and accurately simulate how these elements interact with a mine design. While these tools have progressed markedly, they are, at heart, a gross simplification of the abundant complexity of a natural setting and its response to mining. A generic deep longwall site model was developed that includes aspects of the geology of deep coal mines in the Wasatch Plateau and Book Cliffs coal fields of Utah. The site model contains a set of common features and observations of how these features typically respond to mining. This site model was the basis for evaluating use of empirical, boundary element and volume element stress analysis tools to analyze the distribution of stress around a deep longwall panel. More specifically, this evaluation examined shifting of stress to panel abutments and gob, distribution of stress in the abutment, and deformation and failure of bridging strata. Measurements of abutment stress changes at two sites in the Wasatch Plateau region were used to illustrate model calibration. Overall, these comparisons highlight the considerable differences between methods. Volume element tools can incorporate considerable detail and have fewer underlying assumptions, but this detail carries a considerable computational cost. Boundary element tools are much more efficient. But this efficiency also comes at a cost of added assumptions. These assumptions were challenged by the presence of a strong sandstone unit in the overburden, leading to boundary element results that depart significantly from volume element results. Empirical rules are the simplest, but are even more burdened by assumptions, many of which are implicit in underlying cases. Insight into the nature and impacts of underlying assumptions in each method is essential to proper use of results in mine design. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health

Jan 1, 2009

By L. R. Moore

Arsenic is among the list of major contaminants in mining aqueous waste streams. Though the elemental form is toxic, the aqueous oxyanions are more so. The most common forms of arsenic released during mining processes are arsenate and arsenite. The common treatment technologies to date can be summed up in these major categories: oxidation, coagulation, absorption, and media filtration. These methods can often involve many expensive processing steps that may also be limited by variables, such as total dissolved solids, other cations and anions, and the oxidation state of the arsenic. An innovative technology, falling in the absorption category, was developed that can successfully reduce such aqueous forms to a level below the EPA recommendations. This new technology offers a unique and viable solution which is transparent to the above mentioned limitations.

Jan 1, 2012

By Nick Karl, David Wilburn

"The mission of the U.S. Geological Survey (USGS) National Minerals Information Center (NMIC) is to collect, analyze and disseminate information on the domestic and international supply of and demand for minerals and mineral materials essential to the U.S. economy and national security. Understanding mineral exploration activities and trends assists government policy makers, minerals industry decision makers and research entities in identifying where future sources of mineral supply are likely to be discovered, the amount and type of these resources and factors that may affect exploration and development.This review summarizes significant exploration trends related to active sites and budgets, mineral commodities and regional factors for the years 2001-2015. Data were compiled by specialists in the USGS-NMIC, and reported annually in the USGS-NMIC Minerals Yearbook series and in the May issue of Mining Engineering magazine. External data for these analyses were derived from industry sources, published literature, and SNL Metals & Mining, an offering of S&P Global Market Intelligence (New York, NY).The USGS-NMIC compiled exploration site data for more than 80 mineral commodities, focusing on base metals, diamond and precious metals. More than $138 billion constant U.S. dollars were budgeted by the minerals industry from 2001 through 2015 to explore more than 16,000 mineral deposits globally (SNL Metals & Mining, 2016a). Annual analyses identified where mineral exploration took place by principal commodity target, ranked the magnitude of activity in each region, identified the factors that most affected changes in exploration activity and highlighted developments that led to changes in global supply or increased diversity of supply to the United States. Geographic classifications noted in this report were Africa, Australia, Canada, China, Latin America, Pacific, Russia, United States and Rest of the World."

Apr 1, 2017

By S. Asokan, D. Rathod, Ch. V. G. K. Murty

Tata Steel, a steel arm of Tata Group, is Asia's first and India's largest integrated private sector steel company. Tata Steel’s turnover in fiscal 2004-05 was nearly US$ 3.25 billion. As part of its vision to grow in related industries, Tata Steel is poised to enter the Titania businesses in the Indian state of Tamil Nadu. The Titania project will involve mining, separation of ilmenite & other co-minerals, beneficiation of ilmenite to synthetic Rutile and further maximum value addition to Titanium metal. This paper outlines the journey from the concept to current findings of the Bankable Feasibility Study in developing Sattankulam Heavy Mineral Sands Deposits in the State of Tamil Nadu, India by Tata Steel.

Jan 1, 2005

By Antonio Nieto

According to the analysis of surface powered haulage accidents involving off-highway haul trucks in openpit mining, the U.S. Mine Safety and Health Administration (MSHA), reported 1,300 fatal accidents from 1990 to 2005. Of these, 163 were considered off-highway truck haulage accidents, and at least 23 involved collisions of an off-highway truck with a neighboring vehicle or a worker on foot (Nieto and Dagdelen, 2006). In general, an average of 18 nonfatal accidents and three fatal accidents occurred in openpit mining per year when equipment backed over the edge of an embankment, stockpile or dump point (Fessak, et al., 2003). The specific problems that need to be solved can be determined by carefully studying the accidents involving haulage trucks (Marrara, et al., 2004). Solutions to haulage truck safety must consider the human factors affecting each task even when engineering solutions seem most appropriate. In surface haulage, human performance becomes a critical issue because of the unusual demand the vehicle?s places on their human operators: ? Roadways and working areas change frequently in mining operations. ? The sheer mass of mining equipment such as trucks requires control inputs (e.g., braking) far in advance of the desired action. ? Rough roads, loading and unloading impacts can subject the driver to dangerous shocks and vibration. ? Visibility is sharply curtailed by the bulk of the vehicle generating large blind spots. All of the above issues can be attributed partially to the lack of visibility (Pyles et al., 2003). Driver visibility and communications are key issues to reduce mining truck accidents. Analysis of fatalities and injuries involving mining equipment demonstrates the need to develop new intervention and control strategies to mitigate the risks associated with mining equipment operation. Ongoing development of these and other new strategies is required to achieve a reduction of injury in the mining industry

Jan 2, 2010

By E. Lammer

"Underground mining processes are dangerous. The design of mining equipment, which is able to cope with the hostile underground environment, is a challenge for all machine manufacturers. Presupposition for realizing the vision of SANDVIK for zero harm for working with SANDVIK equipment is the installation of the appropriate processes. Into the product engineering and product development processes of Sandvik Mining and Construction, a specific "Product Safety Process" has been integrated, where all safety related activities like identification of all life cycle hazards, risk management and safety verification / validation are planned, performed and documented. Product safety shall be „designed into" the products. Therefore, specific research activities have been started, to address the safety and health related topics for the development and for the engineering of SANDVIK mining machines."

Jan 1, 2011

By A. J. Hendron, J. E. Monsees

INTRODUCTION This paper is the outgrowth of work done by the authors to prepare the seismic design criteria for underground structures on the Southern California Rapid Transit District (SCRTD) Metro Rail Project. It is a follow-on to a similar paper presented at the October, 1984, ASCE National Convention (17). For design, the earthquake-induced distortions recommended herein are to be added to the normal static loading conditions for the underground structure. This design approach has been used by 18 section designers on the SCRTD Project. Preliminary results from two- and three-dimensional finite element solutions have partially verified the approach. Areas where additional research is needed for special cases are identified. EFFECTS OF EARTHQUAKE The effects of earthquakes on underground structures may be broadly grouped into two general classes -shaking and faulting. In response to earthquake motion of bedrock (shaking) , the soil transmits energy by waves. Seismologists identify various types of earthquake waves, but underground engineers are generally interested in the effects of transverse shear waves which produce a displacement of the ground transverse to the axis of wave propagation. The orientation of propagation is generally random with respect to any specific structure. Waves

Jan 1, 1985

By A. M. Elmahdy

An amphoteric collector was tested for dolomite removal from phosphate ore. The effects of some operating parameters and their significance on the flotation of dolomite were studied using statistically designed experiments. The parameters studied were impeller speed, pH and collector dosage. Analysis of the results showed that pH is the most significant parameter. Moreover, a concentrate containing 0.53% MgO and ~31.1% P2O5 with a recovery of ~ 90% can be achieved at optimum values of studied parameters, i.e., a pH of 12, an impeller speed of 1,000 rpm and a collector dosage of 2.5 kg/t.

Jan 1, 2007

By Mostafa Benzaazoua, Mariam El Adnani, My Ahmed Boumehdi, Rachid Hakkou, Salah Ouhamdouch, Abdelmalek Goumih

This study focuses on the environmental characterization and assessment of long-term neutral mine drainage (CND) potential from waste rock piles at the abandoned Erdouz mine in Morocco. The study involved metallographic analysis, static tests, and column tests. Results indicate that the waste rock is not an acid mine drainage generator but produces CND, mainly with sulfates exceeding Moroccan standards. The waste rock is relatively stable and could be reused after pretreatment.

Jan 25, 2022

By M. Superfesky, P. Michael

Introduction The US Office of Surface Mining (OSM) is proposing changes to the Code of Federal Regulations in the interest of minimizing the adverse effects of excess-spoil-fill construction on the “prevailing hydrologic balance, fish, wildlife and other environmental values” (70 FR 35112). The proposed changes will require: (1) minimization the amount of excess spoil generated at a mine site; (2) minimization of the size of the fills constructed; (3) consideration of alternative configurations for disposal; and (4) development of a disposal plan that would minimize adverse impacts to the environment.1 To achieve those objectives, mining companies operating in steep-sloped Appalachia will likely build excess spoil fills (also called valley fills) that toe out at higher elevations in the hollows (i.e. to prevent or limit burial of streams). Consequently, the slopes of fill foundations will generally be steeper. Whereas the authors of this paper support these measures to protect the hydrologic balance and general environment, we wish to point out that placement of fills on steeper foundations can negatively impact the stability of the fills if proper care is not taken during their construction. It is important to note that in addition to impairing human safety, valley fill instability can negatively impact streams, the riparian habitat etc., and thus defeat the very purpose of the spoil minimization measures proposed. We do not, however, propose additional regulatory requirements pertaining to valley fill stability. Rather, we intend to emphasize the importance of engineering requirements already on the books, especially as they apply to the predominant type of valley fill constructed: the durable rock fill. We believe that the practice of restricting valley fills, to higher elevations in the watershed leaves less room for error in the design and construction of stable structures. This paper gives a quick review of the nature of excess spoil generation; methods and requirements of excess spoil fill construction, and the to-date stability record of the fills. The interest in excess spoil minimization and how it affects valley fill construction is also discussed. Most importantly, we will review long-standing issues pertaining to proper design and construction measures with respect to durable rock fills and discuss how they will become more critical as spoil minimization is practiced.

Jan 1, 2007

By Gary B. Glass

Seventeen percent of US coal production now comes from the 19 surface coal mines in the Powder River Basin of northeastern Wyoming. The Powder River Coalfield, which coincides with this topographic and structural basin, is unique to the conterminous US, in that it contains an estimated 934.4 Gt (1.03 trillion st) of in-place coal resources. At least 13.2 Gt (14.6 billion st) is a compliant, strippable reserve base. In 1993, an estimated 162 Mt (179 million st), or 98% of the coal mined in this Wyoming coalfield, came from the thick - average 30.5 m (100 ft) - subbituminous, Wyodak coalbed, or from the Anderson and Canyon coals in the one mine where the Wyodak is split into two separate coalbeds. The other 2.7 Mt (3 million st) of coal mined in the Powder River Basin in 1993 came from the School, Badger, Monarch and Deitz No. 3 coalbeds. In this "world class" coalfield, there are at least 13 other persistent, 3 to 15 m (10 to 50 ft) thick, coalbeds as well as the Big George and Lake De Smet coalbeds, which are each 61 m (200 ft) or more thick in places. None of these latter 13 coals are mined at this time.

Jan 1, 1994

By F. Freme

Coal production in the United States in 2008 reached a record level of 1.06 Gt (1,171.5 million st), according to preliminary data from the U.S. Energy Information Administration (EIA) (Table 1). This is an increase of 2.2 percent, or 22.5 Mt (24.8 million st) above the 2007 level and 7.9 Mt (8.7 million st) above the prior record level set in 2006. Although coal production was higher in 2008, U.S. total coal consumption decreased in all sectors for the year. Coal consumption in the electric power sector in 2008 was lower by 0.3 percent, while coking coal consumption decreased by 2.8 percent and the other industrial sector declined by 3.7 percent. The commercial and institutional sector, that had been called the ?residential and commercial? sector prior to 2008, declined by 0.6 percent in 2008. It is the smallest of all the coal-consuming sectors. (Note: All percent-age change calculations are done at the short-tons level.) U.S. coal exports were significantly higher in 2008, while coal imports decreased during the year. Total coal stocks increased in 2008, as some consumers added to their stockpiles. The coal synfuel industry, which grew throughout most of this decade, disappeared from the scene due to the expiration of the available federal tax credits at the end of 2007. The decline in coal consumption during the year was the consequence of slowing domestic economic growth, particularly in the latter half of the year, combined with the weather conditions in 2008, resulting in lower demand for electricity. Preliminary data show that total generation in the electric power sector (electric utilities and independent power producers, including useful thermal output) in the U.S. decreased in 2008. Coal-based generation also decreased, resulting in a 3.2-Mt (3.5-mil-lion st) drop in coal consumed in the electric power sec-tor. Coal use in the non-electricity sector decreased by 3.3 percent to a level of 72.6 Mt (80.1 million st). The international coal markets in 2008 were the driv-

Jan 1, 2009

By J. Paraszczak

Water-powered jackleg rock drills, introduced recently in South African mines are reported to be more efficient, faster and more comfortable to operate than conventional pneumatic drills. A comparative testing of both drill types was performed in Quebec. Based on its results and time studies done in the mines, water-powered drilling has been reviewed with regards to drilling rates achieved, infrastructure needed, side effects, health and safety considerations. This study shows that the application of water-powered drills may help increase footage drilled and improve working environment, but under specific conditions. The examples of such applications are given in the conclusions.

Jan 1, 1995

By C. J. Greet

Grinding with an electrochemically inert grinding media (i.e., high chrome white iron) shifts the pulp potentials to more oxidising conditions, increases the dissolved oxygen content and reduces the EDTA extractable iron concentration when compared with milling with electrochemically active grinding media (forged steel). These changes in pulp chemistry produce cleaner particle surfaces, reduce reagent consumption, and increase concentrate grades and recoveries. This paper presents a robust laboratory test program that not only demonstrates the changes in the pulp chemistry, but also provide an indication of the magnitude of the metallurgical improvements that are possible. While laboratory studies are interesting, the proof is in the pudding! So, the paper provides an overview of plant trials conducted at several porphyry copper operations around the world: Newmont’s Cadia and Red Chris Operations, as well as Evolution Mining’s Northparkes Operation. These successful plant trials clearly demonstrate that selection of the right grinding media alloy will yield savings in grinding media consumption and reagent consumption as well as increases in revenue through improved copper and gold recoveries. However, many of the porphyry copper mines on the Eastern Pacific are copper-molybdenum deposits. The paper presents laboratory test results for typical copper-molybdenum operations and extrapolate these numbers to what might be expected should a plant trial occur.

Feb 1, 2025

By F. Habashi

The phosphate fertilizer industry is at present based mainly on the use of sulfuric acid. This technology results in the generation of large amounts of radioactive gypsum that represents disposal and environmental problems. Also it involves the use of expensive reactors for acidification that necessitates the frequent replacing the damaged agitators. Applying hydrometallurgical techniques such as in-situ, heap, or vat leaching to phosphate processing could solve these problems. In this case, however, nitric acid must be used and dicalcium phosphate (40% P2O5) may be obtained as a final product. It is insoluble in water but soluble in citric acid and is an excellent fertilizer. This technology does not interfere with uranium recovery if desired. In addition it permits the recovery of rare earths which are otherwise lost in the gypsum.

Jan 1, 2011

By J. Bickson, C. DeGennaro, J. Homer, M. Girman

Powered haulage and haul truck-related fatal accidents are among the most frequent at surface mines. Industry organizations developed guidance on accident scenarios to address haul truck and mobile equipment collision-related accidents. However, there is a need to investigate accident data to prioritize these scenarios and identify factors relevant to developing validation methods for collision warning/avoidance technologies and determining their capabilities and limitations. Standards and effective validation methods are necessary for improving system efficacy within mining operations and promoting industry adoption. To address these needs, researchers from the National Institute for Occupational Safety and Health (NIOSH) investigated available powered-haulage and machinery-related fatal accident reports documented by the Mine Safety and Health Administration (MSHA). Their objective was to gain a perspective for informing the development of test protocols and validation methods through determining the most prevalent accident scenarios and related factors. Our findings afford insight for addressing the most prevalent haul truck scenarios and relevant factors within U.S. surface mining environments.

Mar 2, 2022