Search Documents

By Carl Johnson, D. R. Todd

The Blue Ridge Low Level Outlet (LLO) was a design/build contract to provide a secondary means of discharging water from the Blue Ridge Reservoir. The project involved driving a 3.25 m (11 ft) modified horseshoe tunnel by 293.5 m (963 ft) long utilizing conventional drill and blast methodology. The intake shaft and structure were constructed inside of a sheet pile cofferdam surrounded by a maximum of 20.1 m (66 ft) of water. The shaft was excavated 4.87 m(16 ft) diameter to a depth of 12.8 m (42 ft) below the tremie slab elevation. Steel lining, including a transition from 3.66 m to 2.74 m (12 to 9 ft) diameter and a90 degree elbow were installed in the inlet shaft and then backfilled with concrete. This paper will describe the RFP phase, the design phase, challenges of the underground construction and contractual challenges.

Jan 1, 2005

By S. Noll

Ventilation is an essential part of any underground mining operation. It provides fresh air for workers and machinery, keeps up an adequate mine climate and dilutes and dissipates noxious gases. Possible changes in the economic environment for mining in the future, e.g. increasing energy costs, will necessitate optimization of distribution of airflow within most mines. This paper discusses the scientific set-up for measurements as well as the behavior and influence of parameters of ventilation according to airflow distribution under consideration of technically possible set-ups of mine fans. This study was done in an underground mine with a flat seam room and pillar mining method.

Feb 27, 2013

By W. H. Schiffbauer

The protection of miners, equipment, and infrastructure is discussed. While the primary focus of the described technology is to prevent miners from being injured, struck-by, or crushed by heavy equipment; another major benefit realized is also the protection of equipment and infrastructure. An attempt is made to define and classify the systems used to provide proximity detection and warnings as well as collision detection and avoidance. Information about the speed of vehicles and human operator response time can be a factor in the choice of what type of system and what features are needed to properly address the needs. How the technology adjusts to compensate for various vehicle speeds, while maintaining the same level of protection is noted. The statistics which justify the need of miner protection are provided. The primary system components required, what attributes they feature, and how they respond in the environment, is briefly highlighted. The physics behind the danger zone marker technology and what makes it so robust and reliable is established. Examples of a few mining applications and specific operational modes are provided for both surface and underground.

Jan 1, 2011

By A. Noble, R. Q. Honaker, J. Werner

Recovery of rare earth elements (REE) from coal-related resources has recently received significant interest due to supply concerns and their key roles in critical industries and defense-related technologies. An integrated flowsheet consisting of sorting, crushing/grinding, physical separation, acid leaching, solvent extraction, and selective precipitation was designed to achieve continuous production of rare earth products from various coal-related resources such as coarse refuse and acid mine drainage. A pilot plant was constructed that enabled continuous testing of the circuitry on a range of different coal-based feedstocks. Despite achieving significant success in producing high-grade rare earth oxide products, low REE recovery values and high operational costs necessitated a re-evaluation of the process flowsheet. This article describes the circuitry improvements that were based on both laboratory and pilot plant test results. Roasting as a pre-leach treatment was found to significantly improve the leaching rate and overall REE recovery values. After roasting West Kentucky No. 13 and Fire Clay coal refuse materials at 600 °C, REE recovery increased by 60 and 40 absolute percentage points, respectively. Rare earth concentration in the pregnant leachate solution (PLS) was increased to around 700 ppm prior to solvent extraction using a staged precipitation method. REEs in the precipitate were re-dissolved, purified, and extracted from the PLS using solvent extraction and selective precipitation to values of around 80%. As a result of the improvements, chemical consumption in the acid leaching and solvent extraction processes was significantly reduced. A techno-economical assessment of the improved flowsheet indicated significant commercialization potential.

By S. A. G. Poppen, M. B. Mirza, A. I. Cooley

The U.S. Department of Energy (DOE) is responsible for siting and constructing a licensed geologic repository for commercially generated high-level nuclear waste. Within DOE, the Office of Civilian Radioactive Waste Management (OCRWM) Program has this responsibility. To accomplish this mission, the OCRWM Program is engaged in a multidisciplined effort to identify, qualify, and develop repository sites. The current strategy of the OCRWM Program is to identify candidate repository sites in basalt, tuff, and salt and to develop exploratory shafts at those sites. Within OCRWM, the Salt Repository Project Office (SRPO) identified the salt site for the development of exploratory shafts. The proposed Exploratory Shaft Facility (ESF) in salt will have several primary purposes. The shafts will provide access to the reference repository horizon to permit in situ testing of the salt horizons in order to satisfy the following data acquisition needs: • Verification of the salt repository design parameters and validation of performance assessment models • Demonstration of the constructibility • Capability to adequately seal penetrations into the salt An exploratory shaft is required by 10 CFR Part 60 for the conduct of in situ testing at depth prior to submittal of a license application for construction authorization of a repository. Therefore, construction of an ESF will also facilitate the licensing process.

Jan 1, 1987

By A. Noble, R. Q. Honaker, J. Werner

Recovery of rare earth elements (REE) from coal-related resources has recently received significant interest due to supply concerns and their key roles in critical industries and defense-related technologies. An integrated flowsheet consisting of sorting, crushing/grinding, physical separation, acid leaching, solvent extraction, and selective precipitation was designed to achieve continuous production of rare earth products from various coal-related resources such as coarse refuse and acid mine drainage. A pilot plant was constructed that enabled continuous testing of the circuitry on a range of different coal-based feedstocks. Despite achieving significant success in producing high-grade rare earth oxide products, low REE recovery values and high operational costs necessitated a re-evaluation of the process flowsheet. This article describes the circuitry improvements that were based on both laboratory and pilot plant test results. Roasting as a pre-leach treatment was found to significantly improve the leaching rate and overall REE recovery values. After roasting West Kentucky No. 13 and Fire Clay coal refuse materials at 600 °C, REE recovery increased by 60 and 40 absolute percentage points, respectively. Rare earth concentration in the pregnant leachate solution (PLS) was increased to around 700 ppm prior to solvent extraction using a staged precipitation method. REEs in the precipitate were re-dissolved, purified, and extracted from the PLS using solvent extraction and selective precipitation to values of around 80%. As a result of the improvements, chemical consumption in the acid leaching and solvent extraction processes was significantly reduced. A techno-economical assessment of the improved flowsheet indicated significant commercialization potential.

By Franklin J. Stermole

L. Alan Weakly, member SME, is a senior staff engineer, Exxon Co. Weakly chaired a Mining Engineering committee formed to solicit materials for six planned "personal skills" articles, to be used in ME this year. What follows are Weakly's introductory comments to the series. Upon graduation from college several years ago, I thought that I was sufficiently prepared to embark in my chosen profession. A short time later I realized that several years of on-the-job training was going to be required before I could use my technical training effectively. It never occurred to me that, professionally, I was seriously lacking in any other skills. My spelling could use a little upgrading, but this was not a serious deficiency. I have been very fortunate to have had two employers that recognized that their engineering professionals did lack other skills and made every effort to give them training to correct these deficiencies. The skills I am referring to are those in administration and interpersonal relationships. Most mining engineers and geologists receive very little, if any, college training in these areas. In addition, many companies do not provide this training and many mining engineers and geologists are unaware of their deficiencies. It is for this reason the subject of personal skills development is being introduced in Mining Engineering. The mining engineer or geologist can pursue one of two basic career directions, managerial or technical. In today's technically sophisticated society and highly competitive business climate, both orientations require administrative and interpersonal skills. Most of us are technically qualified and we continue to upgrade our technical skills. But many studies indicate that we, as a group, are significantly weaker in administrative and interpersonal skills than other professional groups. In addition, these studies indicate that engineers, in general, take longer to reach managerial levels and fewer do so. This series in Mining Engineering, then, should help readers strengthen and broaden their professional capabilities. In all industries, including mining and petroleum, economic analysis of potential investment projects is done to select the projects that will give maximum future value from the investment of available capital. Rather than looking directly at the future values to be generated by investing capital in alternate ways for economic decisions, evaluators usually use either rate of return, present value, annual value, a profit to investment ratio, or various break even analysis results to reach economic analysis decisions in evaluating alternative investments. Alternative economic evaluation techniques are used in industry to properly analyze the economic potential of various investment projects. "Discounted Cash Flow" analysis is the phrase commonly used to describe these techniques. Whether you want to analyze projects in mineral, petroleum, real estate, refining, pipe-line transportation, or any other industry, proper application of discounted cash flow analysis techniques enables you to fairly compare the economic potential of alternative projects as well or better than you can using any other project evaluation approaches. It should be pointed out that investment analysis generally involves more than economic analysis. Financial and intangible considerations sometimes are as important or more important to investment decision-making than economic considerations. Economic analysis refers to evaluation of the profit generating potential of projects, that is selecting which alternative projects will generate maximum future value possible from available investment capital. Financial analysis, on the other hand, relates to analysis of where money is going to come from to finance various projects. Regardless of the economic potential of a project, if financial analysis indicates that we cannot finance the project, it likely will be shelved for financial reasons even though it may be economically satisfactory. Many evaluators use the terms "economic analysis" and "financial analysis" interchangeably, but this author considers that to be undesirable. Intangible analysis relates to project factors that are difficult to quantify in

Jan 2, 1984

By Paul R. Smith

The Colorado School of Mines Research Institute (CSMRI) was founded in 1949 to fill mining industry and government needs for minerals research and development. The operations of scores of mines, mills, and plants around the world are based on the results of work done by the Research Institute. Among other things, the Research Institute conducts studies in geology, mine planning, mineralogy, size reduction, minerals processing, and hydrometallurgical techniques in extractive metallurgy. Many CSMRI projects also involve energy and environmental considerations. What follows is a summary of some of the studies in which the Research Institute has been and is currently involved, as well as some comments on trends and developments in the industry.

Jan 2, 1982

By William F. Stowasser

The organization and operations of the information gathering system, and examples of the products prepared for the commodity phosphate rock by the Division of Nonmetallic Minerals, U.S. Bureau of Mines, are used to describe the Bureau's commodity program. Selected examples from publications about phosphate rock are used to illustrate the program. The Commodity Divisions reporting to the Office of the Assistant Director-¬Metals, Minerals and Materials, have the responsibility in the Bureau of Mines to maintain commodity records, understand the present supply and demand status of the commodity, and forecast future supply, demand, and problems. Within the Divisions, commodity specialists have the broad charter of acquiring as much information about a commodity as is necessary to characterize its history, current status, and future. This information and understanding are the base for the development of mineral policies. To accomplish these objectives, the commodity specialists acquire data and information about each commodity and produce a number of standard publications each year. In addition, as circumstances dictate, each specialist will prepare or participate in the preparation of special documents for specific purposes or problems associated with his commodity. In the preparation of reports and publi¬cations, he may communicate with industrial organizations and other Government agencies.

Jan 1, 1975

By Victor F. Paterno

In December of 2007, a joint venture of J.F Shea, Skanska and Schiavone referred to as S-3II, was awarded a $1.15 billion (? 886,880,000) contract to construct the run-ning tunnels and station structures for the Number 7 Line Extension Project in New York City by the Metropolitan Transportation Authority Capital Construction (MTACC) and New York City Transit (NYCT). As part of the contract, a technically complex and critical connection of the new tunnel to the existing, operational 7 Line subway was required. This paper describes the innovative design approach that was conceived to carry out the underpinning and excavation works both within the east-west 7 Line subway tunnel and beneath the north-south, 4 track, 2 level Times Square Station for the A, C & E trains. This underpinning provided temporary support to the subway substructure as the grade of the tunnel invert was lowered up to 10 feet (3 meters) into the rock sub-grade to allow the future subway to pass under the basement of the world?s busiest bus terminal. In addition, the creation of a new portal connecting the existing subway tunnel and the subterranean level of the Port Authority Bus Terminal by means of underpinning structural footings and horizontal spiling/poling of existing ground will be discussed.

By M. S. Safarzadeh

Over the last fifty years, the treatment of enargite concentrates has not received much attention primarily because of the availability of other clean concentrates suitable for processing with existing smelting and/or leaching technologies. As traditional copper ores have become scarcer, copper-arsenic ore deposits have garnered more interest. Arsenic release is a significant concern during the treatment of enargite by pyro or hydrometallurgical methods. Enargite is also very refractive in standard leaching procedures. Thus, economical treatment options for enargite concentrates are needed. Preliminary experiments have shown that the acid-bake leach process could be adapted and used for the treatment of enargite concentrates. In this study, low-temperature (100-400 ºC) sulfuric acid baking of an enargite concentrate followed by water-leaching has been evaluated. The results indicate the thermal transformation of enargite to copper sulfate during sulfuric acid baking, with most of the arsenic being released from the concentrate into the gas phase for baking at 400 ºC. The condition for maximum copper extraction (~100%) from the concentrate was found to be 400 ºC, sulfuric acid amount of 0.5 mL/g of concentrate, and 2 h baking time. Part of the arsenic was captured in the form of arsenopyrite (FeAsS). XRD analysis proved the presence of some arsenic in the form of claudetite (As2O3) in the baked concentrate. Acid baking of pure enargite behaved in similar fashion.

Jan 1, 2012

By Rainer Kahrger

During the last decade, advances were made in solvent extraction/electrowinning (SX/EW) technologies. Combined with heap leaching, these technologies made it viable to exploit large, low-grade oxide copper deposits. The El Abra Mine is a good example for such a deposit. The deposit is situated in northern Chile at an elevation of about 4,000 m (14,000ft), 70 km (45 miles) north of Calama. Codelco sold 51% of the El Abra to Cyprus Minerals in June 1994, with Codelco retaining the balance. In 1993, Cyprus and the engineer on the project began discussions withinternational companies regarding the materials-handling system requiredfor the project. These early discussions were considered critical for this fast-track project.

Jan 1, 1996

By Seal. Thom

Large heap leach operations around the world contain significant under-leached metal values that present recovery challenges to operators. The first challenge is to find the location of the highest inventory. High resolution resistivity ? has proven sensitive enough to detect such zones in the interior of heap leach pads to target treatment or re-leaching. Newmont Mining Corp. has adapted the high pressure fracturing technology, used in oil wells to stimulate select zones in heap leach pads to add reagents in 3-D for re-leaching, changing zonal chemistry for improved recovery and heap closure. High Resolution Resistivity ? is able to subsequently monitor injected solution flow and determine directional permeability during Hydro-Jex stimulation. The combination of these technologies has shown strong economic success, for selecting targets in the heaps and monitoring solution application. These technologies are now available to the mining industry for adoption.

Jan 1, 2008

By Mark E. Smith

Oxide ores can consume enormous amounts of expensive sulfuric acid. The problem is amplified with increasing heap heights. One solution is to provide a thin liner and drainage system between each lift of ore, thereby intercepting the pregnant leach leach solution (PLS) after it exits the active lift. However, these liner systems require special attention to hydraulics, slope stability and geomembrane design criteria. Inadequate attention to the first two can result in reduced recoveries, increased acid consumption andsystem failures. The geomembrane selection criteria are different from the base liner, and optimizing its selection can have significant effects on the operation’s bottom line.

Jan 1, 1996

By J. Stephen Slottee, Jerold Johnson

The use of a thickener, without filtration, to produce a non-settling paste (also called thickened tailings) with non-Newtonian rheology has been practiced in Australia for many years for the disposal of red mud. The application of paste thickening technology outside of alumina is relatively new. Interest and installations in paste thickening are rapidly growing. Water shortages and environmental pressures make consideration of thickening tailings to solids concentrations within the paste range necessary in most new tailings projects. The paste thickeners at the DeBeers CTP plant in Kimberley, South Africa are the latest example of paste tailings disposal on the surface, also called “stacking”. Houman (2003) The use of a paste thickener as an alternative to filtration for mine paste backfill is a more recently developed application. This paper describes the principles of design and general operating characteristics of a paste thickener compared to the conventional and high-rate thickener. The application and operating performance of paste thickeners in mine backfill is discussed as an example. An integrated approach to process design is described that matches the performance of the thickener, pumping system, and application on a common rheological basis to ensure that none of these steps prevents achieving process performance targets.

Jan 1, 2005

By S. C. Tadolini

Roof support systems have evolved from standing posts and timbers to a generation termed ?big nails? where steel bars are inserted into boreholes and anchored with expansion shells and/or resin cartridges. These systems have been effective but are limited to mining height. Additionally, the properties of steel do not resists shear forces or have the flexibility being required in difficult ground conditions. The next generation of roof support systems is coupling the best parts of the ?big nail? and resin grouted cable bolt systems. This paper will present the advanced technical solutions of the next generation of cable systems that includes an indented high-capacity PC-strand used with a variety of fixtures. Case histories of support applications will be presented.

Jan 1, 2012

By Yiming Sun

The 5-mile long Bay Tunnel is a major water supply facility to be constructed under the San Francisco Bay and adjacent marshlands between the San Andreas Fault to the west and the Hayward Fault to the east. The tunnel will have a two-pass lining system consisting of a watertight precast concrete segmental initial lining and a welded steel pipe final lining. Considering the Bay Tunnel?s location between two major active faults, the design earthquake produces a significant peak ground acceleration estimated at approximately 0.6g. To develop a design that can achieve the seismic performance objectives, full dynamic seismic analyses were performed using site-specific earthquake time histories. The analyses considered soil-structure interaction and an evaluation of the transverse and longitudinal effects of the design earthquake. This paper describes the seismic analyses and the design measures recommended to minimize potential adverse effects of the design earthquake on the tunnel final lining.

Jan 1, 2008

By Xiaodong Ma, Marek Pawlik

Introduction Guar gum is a natural nonionic polysaccharide. Guaran, the functional polysaccharide in guar gum is a chain of (1?4)-linked ß-D-mannopyranose units with a-D-galactopyranose units connected to the mannose backbone through (1?6) glycosidic linkages. The poly-mannose chain is randomly substituted with galactose units at a mannose-to-galactose ratio of 1.8-1.0 [1]. Cheng et al. reported that the molecular weight of natural guar gum is 1.935 • 106 [2]. Robinson et al. found that the molecular weights of five grades of commercial guar gums ranged from 4.4 • 105 to 16.5 • 105 [3]. Guar gum is frequently used as a depressant of naturally hydrophobic gangue minerals (e.g. talc) in the flotation of PGM-bearing ores, and according to Harris et al. a wide variety of modified guar gums are available for this application [4]. The Canadian potash industry utilizes natural guar gum as a blinder of water-insoluble slimes in the flotation of potash (sylvinite) ores, a process that is carried out in a saturated KCl/NaCl brine. The role of the polysaccharide is to prevent a primary amine collector from adsorbing onto these unwanted fine minerals. Hydrophobic interactions between basal cleavage planes and the polymer appear to be involved in guar gum adsorption on talc [5,6]. Liu and Laskowski stressed the importance of metal impurities on mineral surfaces that can serve as the active sites for polysaccharide adsorption [7]. This postulate was consistent with the later observation that, in addition to hydrogen bonding, the adsorption of guar gum onto talc was strongly dependent on the surface concentration of magnesium sites [8,9]. In this case the adsorption process was visualized as metal-polysaccharide complexation facilitated by the cis-configuration of the hydroxyl groups of mannose monomers. Hydrogen bonding and chemical interactions with metal sites were also suggested by Rath and Subramanian in their studies on guar gum adsorption on biotite mica [10]. In a recent study, Wang et al. demonstrated that hydrogen bonding is the main driving force behind guar gum adsorption onto talc [11]. Their data also show that the adsorption density of guar gum on alumina is about five times lower than the adsorption density on talc. Pawlik and Laskowski reported that the amount of guar gum adsorbed on illite was independent of ionic strength over a wide range of salt concentrations [12]. The adsorption density of the polysaccharide on illite did not measurably change with ionic strength from that of distilled water to about 50%-saturated KCl/NaCl potash brine (~3N KCl/NaCl). However, guar gum adsorption on dolomite dramatically decreased over the same range of ionic strengths, and no reliable explanation of that phenomenon was proposed [12]. The water structure-breaking or structure-making capabilities of background ions are usually ignored when discussing adsorption mechanisms of polymers. The concept of “structure breakers” and “structure makers” was first introduced by Gurney, and Frank and Wen who postulated that each ion is surrounded by three distinct regions of water structure [13,14]. In the first layer, water molecules are tightly bound to the ion. The second region extends farther away from the ion and is referred to as the region of structure breaking. Only at larger distances, where the ionic field is weak, water molecules form the “normal” ice-like structure. It is also now recognized that the first layer can be further divided into the primary and secondary hydration shells. Small, strongly hydrated ions reinforce the “normal” structure of water and the region of structure breaking disappears. In contrast, large less-hydrated ions disturb the ice-like structure and generate an extensive region of structure breaking. Experimentally, these two effects can readily be distinguished through viscosity measurements. Increasing concentrations of structure-breaking ions result in a decrease of the viscosity of aqueous solutions. On the other hand, increasing amounts of structure-makers significantly reduce the viscosity of water. Alkali metal cations form a sequence known as the Hofmeister series. The Hofmeister series - Cs+, K+, Na+, Li+ - orders the cations from the least hydrated to the most hydrated. Based on literature viscosity data for aqueous

Jan 1, 2005

By T. McWaters

Miami Copper Company began a block-caving operation in 1911 using a gravity mill to separate copper minerals from the Pinal Schist host rock. The tailing was deposited by the upstream method using perimeter launders and spigot valves in six canyons adjacent to the mill until 1932. In 1928 the larger and more distant Solitude tailing pile was developed which by 1932 was receiving all tailing except for upsets. In 1925 Miami Copper converted its gravity mill to flotation which began to produce higher sulfide copper recoveries.

Jan 1, 1990

By R. W. Fedors, S. T. Green, R. A. Hart, D. B. Walter

Computational fluid dynamic (CFD) modeling of a potential nuclear waste repository drift may be an important tool to estimate moisture redistribution caused by natural convection within the drift. To refine and support CFD techniques, a small laboratory cold-trap experiment was developed. Results from numerical modeling of the laboratory experiment show the sensitivity of the bulk air flow rate and average air temperature within the drift to several key parameters, including various boundary condition assumptions and surrounding porous media properties.

Jan 1, 2004