Search Documents

By M. K. Sichone

Anglo Platinum?s Waterval smelting complex based in South Africa operates the Anglo Converting Process (ACP) that produces SO2 offgas. This SO2 offgas is treated in a double-contact, double-absorption acid plant allowing for conversion efficiencies higher than 99.90 %. The catalytic converter used in the acid plant to convert the SO2 to SO3 is a 4-bed reactor loaded with a combination of cesium-promoted and conventional vanadium pentoxide catalysts. In June 2008 there was a shutdown, in which one of the main activities was to screen the catalyst. Before this shutdown, the operator would control the converter pass temperatures manually, via the SCADA, especially during plant start-ups after which some of the automatic temperature controllers were used. After the shutdown, the control philosophy was revisited and all temperature controllers were put on auto mode during plant start up. Furthermore the set points of the pass inlet temperatures were reduced to maximize conversion in the first two passes. The result has been a reduction of SO2 emissions, from a daily average of 50 ? 70 ppm to as low as 20 ppm for similar sulphur dioxide and oxygen concentrations. Further work has been done to maintain high bed temperatures in the third and fourth passes at low SO2 strengths by splitting the gas stream between pass 1 and 2 thus increasing the SO2 content in the gas to pass 2. This increases the temperature of the gas exiting the second pass, which results in higher temperatures in passes 3 and 4. Comparison of the converter performance prior to and after the changes is made. The benefits of partially bypassing the first pass to increase the SO2 content in the gas to the second pass are shown. Conclusions and scope for further work have been drawn from the comparisons.

Jan 1, 2009

By P G. Gaylard

The minerals Industry carries out over US$ 2 billion of R&D annually. The R&D is performed at three levels ? in house research facilities; on a one-on-one basis with a research provider; as syndicated (collaborative) research. The key to a successful R&D programme is project selection. It is suggested that at this time of ?bounty? for the minerals industry the research portfolio should contain some ?blue sky? but potentially long term significantly beneficial projects. This said, the projects should align the technical concepts with the business imperatives. AMIRA has found the ?Road Map? concept has assisted in defining areas for R&D. Examples of this methodology using a Copper Road Map developed by AMIRA for the copper producers operating in South America is presented. The benefits derived from syndicated research are also discussed.

Jan 1, 2007

By R. Burger, M. Masukawa

Cato Ridge Alloys (CRA) is a joint venture company between Assmang of South Africa, Mizushima Ferro Alloy Company (MZK) and Sumitomo Corporation from Japan. Negotiations for the formation of the company started in 1992 with the joint venture agreement signed on the 19th September 1996. MZK was to supply the technical know how for the production of Medium and Low Carbon FeMn while Assmang was to manage the day to day activities of the company. Sumitomo Corporation was to act as facilitator between Assmang and MZK and, together with Ore and Metal are responsible for the marketing of the refined products. The conceptual design of the plant started in December 1996 and the first charge of molten high carbon ferromanganese metal was charged on the 19th January 1998. Problems experienced during the initial startup period were addressed resulting in substantial operational improvements. A build-up in the stock of fine metal was addressed through the development of a process to remelt the fine metal, the development of a market for fine metal and the upgrading of the crushing and screening plant to reduce the generation of fine metal. The mass yield from High Carbon Ferromanganese to Refined Ferromanganese was increased through the implementation of statistical process control, changes to the blowing patterns and the development of a sampling device for taking samples during the process. Converter refractory consumption was reduced. This was achieved on the converter by improving the cooling of the converters with the installation of cooling fans and cooling fins. The heating schedule of the converters was changed for improved refractory life. Production schedules were modified to allow cooling of the refractory between low carbon erromanganese charges. Additional changes made to improve operations were: ? Changing from mehanite casting trays to metal fines beds. ? Installation of sonic horns in the baghouse to prevent the bridging of dust. ? Improved welding on the lance tips.

Jan 1, 2004

The University of New South Wales (UNSW Australia) has been a world leader in the development of innovative virtual reality technologies over the last 15 years. AVIE (Advanced Visualisation and Interactive Environment) was developed by iCinema as a collaborative venture between UNSW?s Faculties of Engineering and the College of Fine Arts. This is the world?s first 360°-surround, virtual reality (VR) stereo projection theatre system. The School of Mining Engineering at UNSW Australia has developed 18 different virtual reality modules aimed at mine safety training and mining engineering education. These modules are being regularly used in both the mining industry and the university. The School of Mining Engineering is continuously involved in the development of different modules. Research is also currently being conducted on the implementation of other technologies into this environment. Artificial intelligence (AI) and fuzzy logic are tools that the authors would like to consider implementing in future module development. This paper will review current research in both these areas and consider options for applying these technologies.

Jan 1, 2014

Significant advances have been made in the design of centrifugal slurry pumps that are used for pumping high-density viscous and paste slurries. This paper presents the results of a series of centrifugal pump performance tests that were conducted using an FLSmidth 6 x 4 Krebs millMAX centrifugal pump. The pump was fitted with a dry mechanical seal to prevent dilution of the slurry from gland service water, as the theology of the slurry is sensitive to small changes in slurry density. Tests were done using paste kaolin slurry with Bingham yield stress values between 578-1 120 Pa and plastic viscosities between 728 and 1491 mPa.s. The viscous properties of the paste during each pump test were measured using a rotational viscometer. Pump head and efficiency de-rating were measured and compared to the correlations of Walker and Goulas (1984). The test data shows the pump's best-efficiency point (BEP) changes and shifts to the left of the performance curve. The pump efficiency decreases as the slurry yield stress increases. The head de-rating data shows more head de-rating at the low flow rates compared to the high flow rates for the high viscosity slurry, which is in line with the findings of Walker and Goulas (1984). This paper demonstrates that it is possible to pump very viscous, high yield stress slurries with limited head and efficiency de-rating using centrifugal pumps, provided that positive suction conditions are maintained at all times.

Jan 1, 2012

By B. Schoevaerts

The ever-increasing depth of mineral extraction presents a challenging environment for hard-rock underground mines. High in situ stresses and associated seismicity with potential rockburst hazards are the major decisive factors contributing to the choice of a ground support regime. Conventional ground support systems, designed primarily for static loads, are not always capable of providing safe working conditions for underground personnel in seismically active mines. Systems specifically developed to resist dynamic loading and allowing for larger deformations are therefore preferred alternatives. High-tensile chain-link mesh has a proven record of successful use in open cut operations in various rockfall barrier installations due to its high energy absorption capacity. It has also been used in underground operations in various parts of the world. Its application in South African underground mining, however, is limited due to the high labour intensity. This paper describes a method of mechanized installation of a chain-link mesh as evaluation at Gold Fields' South Deep Gold mine situated some 45 km south-west of Johannesburg. A purpose-built mechanized roll mesh handler, developed in Australia, was used in this trial. The handler is compatible with all standard multi-boom underground drill rigs and is operated utilizing the hydraulic circuit normally used for the feed arrangement. A number of key performance indicators have been specified as success criteria by Gold Fields: ? A 30% faster installation compared to the conventional methodology ? The mesh should sustain any blast damage when applied to the blasting face ? No unravelling of the mesh when cut ? No failure of mesh under normal conditions ? Reliability of the MESHA® installation handler (availability >90% ? Compatibility of the MESHA® installation handler with AC 282 boomers. Although the energy-absorbing mesh combined with yielding rockbolts is a ground support system of choice for rockburst-prone conditions, the operational upsides recognized during the trial imply that this product can also be competitively used in less demanding ground conditions where weld mesh or shotcrete are customarily used as a primary surface support.

Jan 1, 2012

By Y. Shiraishi, Y. Sakurai

A new method, the gliding cylinder method, was proposed as a wide range viscometer for the measurements of molten salts, slags, and glasses. The method consists of two coaxial cylinders, cylindrical bob and a vessel containing a liquid sample. There is a narrow gap between bob and vessel. When the vessel moves against the bob, the generated force on the bob consists of three types of resistance: (1) Stokes’s resistance on the bob, (2) a capillary flow resistance though an annular gap between vessel and bob, and (3) lubricating resistance in a gap. The last two can be calculated on a theoretical basis but the first cannot be estimated by a simple calculation since a wall effect did not calculate easily. However, it can be assumed that the generated force depends on both the viscosity of a liquid and velocity of the vessel. Thus, the relation between viscosity and a force at desired velocity of the vessel was measured using several standard reference materials including glycerol aqueous solutions and standard reference oils. The results depended on the magnitude of the gap between the bob and the vessel. For the wider gap, it was shown that the viscosity is a linear function of a gradient of force with respect to a vessel velocity. In contrast, if the gap is small, the viscosity depends on the gradient (of force with respect to velocity). This implies that the non-linear phenomena would occur in Stokes resistance. Though detailed analysis is in a further investigation, a calibration method can be applied to determine the viscosity by this method, because good correlation was obtained among these quantities. Viscosity of molten salts, such as NaNO3and ZnCl2was measured by this method as high temperature demonstration. Keywords: viscometer, viscosity, sphere pull-up method, fused salts, molten slags, glass melts

Jan 1, 2004

The spatial distribution of copper grades at the Mansa Mina project is highly variable due to the presence of high grade copper/silver/arsenic breccia bodies. Copper grades within the breccia bodies tend to average about 4.5% copper while grades in the surrounding stockwork average about 1.0%. The breccia is known to occur in the vicinity of significant controlling structures, however, the outline and therefore the thickness of the bodies are far from regular. Due to the high grade of these bodies a significant proportion of the value of the project is derived from the breccia tonnages. The irregularity in the outlines/thickness translates into an uncertainty in the breccia tonnage and therefore in the value of the project. Acknowledging the economic importance of the breccia bodies and the risk associated with the breccia tonnage uncertainty, significant additional drilling has been proposed to both understand the spatial distribution of the breccias and reduce project risk. The costs associated with this additional drilling are not inconsequential; thus, a reasonable question is ‘what value is derived from this additional drilling’? To obtain an answer to this important question, a simulation approach is applied. First the deposit is simulated using the existing drilling and the uncertainty in the resource is defined. Next the proposed drilling program is simulated and the simulated data are added to the existing data. Using this expanded data set a second simulation of the deposit is created and once again the uncertainty in the resource is defined. Using this approach, the reduction in the uncertainty in the resource can be determined. To convert this reduction in uncertainty (or reduction in risk) in the stated resource into a dollar value, a method of defining the increase in the project rate of return necessary to account for risk is presented. Using the two different rates of return, the difference in project NPV and hence the value of additional drilling is determined.

Jan 1, 2003

By P. van der Heever

The genesis of Simrac?s technology transfer practices and future initiatives are discussed in this report. Simrac produces a relatively large volume of research-based health and safety outputs that must be communicated to its tripartite stakeholders and to other interested and affected parties. The wide spectrum and complexity of the transferables, together with the diversity of end-user needs and skills of the recipient population, necessitate customizing of technology transfer practices. In an attempt to optimize this process, a variety of practices are employed. Information is transferred by means of publication and dissemination of a variety of reports (paper, website and CD).Knowledge transfer is directed to health and safety practitioners by means of workshops, seminars, best practice booklets, handbooks and textbooks. Promotion of recently completed projects is directed at targeted recipients by means of project launches. Only isolated cases of piloting and implementation of technologies have been undertaken due to lack of resources and past organizational focus. It is anticipated that Simrac?s new organizational structure and management system, together with end-user involvement by industry champions, from project inception to implementation, will enhance the effectiveness of the technology transfer process.

Jan 1, 2002

By M. Reuter, U. Boin

The target of the current metallurgical industry is to recycle and utilize all their by-products, so as to close the sustainable production loop. Slags are the important wastes and by-products of metallurgical industry, which have been treated, recycled and used worldwide. The present paper summarizes the current status of utilization of the various slags from ferrous and non-ferrous metal production, as well as waste incineration, and recycling of salt fluxes in secondary metal production. In addition, the environmental issues of the metallurgical slags are addressed. The metallurgical oxide slags have stone-like properties and, thus, their major applications are in civil engineering field. The slags should be recycled, modified and processed in a proper way, by taking the environmental impact into consideration. With the treatment of salt slags for melting aluminium scraps, as an example, the recycling and elution properties of the salt slags are discussed. Our research indicates that the viscosity of the salt flux is increased with addition of non-metallic components, that a certain percentage of fines remain in suspension, which determines the viscosity, affecting the settling of heavier materials. High slag viscosity will lead to more fine aluminium metal entrapped in the salt slag (may also be seen as a high temperature slurry), and thus increase the load of salt slag recycling. Keywords: recycling, environment, metallurgy, slags, fluxes, salts.

Jan 1, 2004

By J. Kortnik

Mining has always been, and still is, an activity which is vital for the development of mankind. This is because a predominant proportion of industrial products and energy is produced from raw materials that are excavated using mining methods. The need for environmental protection and the close proximity of urban settlements and mines in Slovenia have necessitated ever stricter requirements for the excavation of raw materials and the introduction of more environmentally-friendly mining methods. This is achieved by implementing a closed eco-technological cycle of raw material excavation within the scope of mining methods. In surface mines, this means prompt reclamation of the degraded surfaces, and in underground mines the use of methods with minimized impact on the surface and on underground water. In underground mines, mining methods with backfilling installed according to the multi-barrier disposal system are the only ones that allow the possibility of implementing a closed eco-techno-logical cycle of excavating raw materials. Various industrial waste materials are also included in the backfilling material in order to improve its strength properties. Backfilling consisting of several different waste materials is produced in the form of a composite. Before backfilling consisting of waste material composites can even begin to be used in mines, an environmental impact assessment of its suitability for mines needs to be made. In order to make such an assessment, a pressure leaching cell and an open diffusion cell were made, i.e. a pressure leachate test and a sorption test were developed. The two cells and the developed tests will enable the study of the influence of backfilling on the environment if installed in an underground mine. The pressure leachate test performed with the use of the pressure leaching cell simulates leaching from a consolidated backfill during the seeping of underground water into the backfilling material under pressure. The sorption test performed in an open diffusion cell simulates the flow of eluate leached from the backfilling material through the rock/geotechnical barrier. The two tests were developed in such a manner that they are performed either in succession immediately after one another, but they can also be performed separately at a certain time interval. The paper presents an assessment of the suitability of backfilling made of different waste material composites. Keywords: environmental impact assessment, multi-barrier disposal system, waste material composites, pressure leachate test, sorption test, pressure leaching cell, open diffusion cell, eco-technological cycle, mining methods with backfilling.

Jan 1, 2003

By J. Utt

Recent developments in circulating fluidized bed (CFB) once-through supercritical technology (OTSC) have enabled this technology to be offered as a utility-scale alternative competing head-to-head with pulverized fuel (PF) OTSC offerings. One clear example is the CFB supercritical unit at the Lagisza Power Plant in Poland, owned by PoludniowyKoncernEnergetyczny SA (PKE). This unit has now been in commercial operation for three full years, exhibiting very good performance, and has validated Foster Wheeler?s performance model at this utility scale as well as for units in the 600 MWe and 800 MWe size ranges offering net efficiency of ~43 per cent (LHV basis). This operating unit has also proven the use of the world?s first FW/BENSON? vertical-tube OTSC low mass flux technology. Since the Lagisza original international tender specified OTSC PF technology, it is important to note that the alternative selection of CFB OTSC technology over conventional PF technology is of historic significance, not only for the validation of the CFB supercritical platform as a viable alternative to conventional PF technology, but it also positions the CFB OTSC with fuel flexibility for offering of sizes up to and including 800 MWe units. This paper explores the differences between CFB OTSC technology and standard PF OTSC in utility power generation. Selection criteria, fuel burning range in both technologies, and other selection drivers are discussed. Economic analysis of both technologies, based on existing cases, is also provided. Also discussed are the technical advantages and uses of each technology. Foster Wheeler has recently been awarded a contract for four units of CFB OTSC technology, which utilizes a 2 on 1 configuration of two 550 MWe CFB OTSC boilers on two single 1000 MWe turbines. Essentially this provides a fuel-flexible low-emissions alternative to a 2 × 1000 MWe solid fuel power block.

Jan 1, 2012

Electrochemical measurements are presented on electro-deoxidation of silica in molten calcium chloride at 900°C, with porous silica pellets as starting material. Measurements during pre-electrolysis (to remove water from the melt) showed electrochemical noise, which is consistent with the evolution of hydrogen. Throughout, the dominant anodic reaction appears to be CO2formation, based on the observed potential at the anode, and measured anode wear. Because of the presence of dissolved CaO in the melt, some of the CO2 candissolve in the melt; the resulting calcium carbonate formation was confirmed by electrolyte analysis after reduction runs. Reduction of dissolved CO2 at the cathode is likely to contribute to the background current during the reduction process. For the electrode and cell configuration used here, most of the over potential arises from polarization of the anode, and ohmic potential drop in the electrolyte.

Jan 1, 2006

By T. Frömmer, H. Wagner

An inter-disciplinary geotechnical study has been carried out in an Austrian magnesite mine. The paper describes the how geological data, in situ and laboratory tests as well as subjective, empirical, geophysical and numerical methods have been used to identify critical areas in the mine. In einem österreichischen Magnesit Bergbau wurde in den letzten Jahren eine interdisziplinäre geotechnische Studie durchgeführt. Der Vortrag beschreibt den Einsatz subjektiver, empirischer, geophysikalischer und numerischer Methoden zur Identifikation geotechnischer Problembereiche Ces dernières années des études géotechniques interdisciplinaires sont effectuées dans une mine souterraine de magnésite en Autriche. Ce rapport trace l’application des méthodes subjectives, empiriques, géophysiques et numériques pour identifier les zones problématiques dans la mine

Jan 1, 2003

By M. Royker

Gold has been demonstrated as a possible catalyst for oxidation reactions. Some evidence for a possible promotion effect of platinum has also been recorded. The influence of platinum as promoter for Au/?-Al2O3 prepared via anionic ion-exchange for the oxidation of glycerol was investigated in a batch reactor at 60°C. It is inferred that the addition of platinum reduces the catalytic activity and therate of deactivation, resulting in an overall higher final conversion of glycerol with increasing platinum loading. The addition of platinum to the catalyst favours the formation of the desired product, glyceric acid.

Jan 1, 2012

By A. P. Squelch

The high incidence of accidents and fatalities in the South African mining industry, in particular those associated with falls of ground, is often attributed to ineffective and/or inappropriate training methods and material. Recently introduced mine health and safety legislation in South Africa also requires that all mine workers receive appropriate and effective training to enable them to operate safely in their given mining environment. There can, therefore, be no doubt that methods to provide effective training, in particular safety related training, are urgently required in the South African mining industry. In the search for alternative and improved training approaches, attention has fallen on virtual reality (VR) technology as a possible solution. VR has found acceptance in a number of industries as an effective method of training for a variety of work place activities, including those of a safety related nature. VR has successfully been applied in a number of industries to improve the effectiveness of safety and hazard awareness training. The CSIR: Division of Mining Technology (CSIR Miningtek), in conjunction with the Safety in Mines Research Advisory Committee (SIMRAC), therefore evaluated the potential of VR to be used as a training medium in the South African gold and platinum mining industry. Aspects of the evaluation included an assessment of the technical capability of VR to represent a typical underground mining environment with sufficient realism and the relevance of the VR training concept for a largely illiterate workforce. For these purposes, a prototype PC-based VR hazard awareness training simulator has been developed by CSIR Miningtek, and a series of evaluation sessions conducted at a typical deep level gold mine. The conclusion from this evaluation work is that virtual reality technology has the potential to provide effective training systems that are relevant to the South African mining industry. Keywords: Virtual reality, mine training, safety training.

Jan 1, 2001

Rock mass classification systems are extensively used in rock engineering design work, and mine design is no exception. Among the systems most widely used for mining-related design work are the NGI 0-system (Barton et al., 1974), the RMR system (Bieniawski, 1976), the MRMR system (Laubscher and Taylor, 1976) and, more recently, the GSI system (Hoek et al., 1998). Classifying the rock mass is widely seen as being the fieldwork required to characterize the rock mass and enable the application of empirical design methods associated with the different classification systems. This paper argues that it is fundamentally important to recognize the distinction between rock mass characterization and rock mass classification. These two processes should, in most cases, be separated from each other. Rock mass characterization should be used to determine the intrinsic properties of the rock mass independently of the application; i.e. independent from the infrastructure to be designed, the size, shape, and orientation of the excavation(s) or pillar(s), etc. Rock mass characterization should also be compatible with most classification systems and empirical design methods to be used. Rock mass characterization is the background fieldwork required to perform rock mass classification and/or engineering design work. Rock mass classification is the subsequent step to the characterization, and an integral part of the design process. Parameters that vary according to the design, such as the relative orientation of geological structures compared to the opening or the mine-induced stresses, should be calculated as part of the rock mass classification and design process, rather than during the rock mass characterization process. The failure to distinguish between rock mass characterization and rock mass classification can lead to major design errors and poor results.

Jan 1, 2012

By K. P. Kavun, M. N. Denisov

Discussed in the paper is the redesigned reserve/resource classification for solid minerals being put forth by the authors to replace the acting Russian classification of 19961. The new version is based on the traditional foundations of former Russian classifications and the principles of the ‘McKelvey box’, both categorizing mineral resources according to the degree of geological assurance and economic viability. Based on these approaches the classification deliberately deals with both reserve and resource categories very similar to those established by the Geneva Accords in terms of definitions implied. The authors proceed from the UN-ECE proposed concept of ‘reserves’ being a part of ‘total resources’ explored in great detail by geological and feasibility studies and economically mineable at the time of reporting. The draft classification distinguishes ‘proved’, ‘probable’ and ‘possible’ categories of reserves depending on the stage of feasibility assessment carried out, i.e. the degree of detail and accuracy with which modifying factors affecting mineability of an orebody are taken into account. The reserves are regarded as a product of feasibility assessment of ‘measured’, ‘indicated’ and ‘inferred’ resources. The portions of them not having been classified as ‘reserves’ are regarded as composed of two classes: ‘subeconomic’ and ‘potentially economic’ resources (or ‘resource base’). All the cells of the classification matrix are provided with traditional for Russia alphanumeric designations and appropriate UNFC codes. The classification scheme recommended is viewed as a step forward in improvement of the State inventory and reporting mineral resources in market conditions, conducive to cross-border professional collaboration in the field of providing reliable information on the mineral rawmaterials base of the world’s economy. Besides, it recommends an easy way to get rid of amethodological error in the UNFC classification scheme where consecutive stages of geologicalexploration are identified with a single inherent degree of geological assurance. Keywords: mineral resources, mineral reserves, classification, geological assurance, feasibility studies, subeconomic resources, undiscovered resources, competent person.

Jan 1, 2003

By D. Malovichko

Seismic events and pillar failures observed in two platinum mines in the Rustenburg area, South Africa, were investigated. We studied the sources of approximately 300 largest seismic events recorded in 2009. Moment tensors of these events were estimated from amplitudes and polarities of P- and S-waves. The inverted mechanisms contain isotropic implosive components in many instances. Analyses of uncertainty of the moment tensor solutions confirmed the significance of the implosive component in general. Several documented cases of pillar failure were considered in detail. For each of these a seismic moment tensor was calculated from an elastic stress model assuming an instant removal of a failed pillar. The geometries and magnitudes of the theoretical seismic moment tensors are in agreement with the observed (i.e. inverted from seismic data). The results indicate that either pillar failure or fracturing in the proximity of the reef (within a fraction of the dominant wavelength of seismic waves) are responsible for a significant portion of the large events recorded in these mines.

Jan 1, 2012

By Merete Tangstad, Kai Tang

The primary aim of the present investigation is to develop a model which permits to calculate/predict the viscosities of ferromanganese slags, typically focus on the MnO-SiO2-Al2O3-CaO-MgO-FeO multicomponent system. The present viscosity model emphasizes the ability of prediction, i.e. using the binary parameters to extrapolate the viscosities in ternary and higher order systems. To this end, a physical sound model is essential. Temperature dependence of viscosity is described by the Eyring?s formalism. The well-known cell model is used to define the SiO44- tetrahedra in the silicate melts. Composition dependence is expressed in term of viscous activation energy, which is characterized by the binary structural units. The viscosities in ternary and higher order systems are hence predicted using the binary activation parameters. The model has been used to calculate the viscosities in the whole liquid composition range of ferromanganese slag.

Jan 1, 2007