Search Documents

By F. Lanaro, K. Röshoff, R. Christiansson, L. Jing

This paper presents the results of a project for developing a methodology for empirically determining some of the mechanical properties of the rock mass at the Äspö Hard Rock Laboratory, Southern Sweden. Using the equations available in the literature, the deformation modulus, friction angle, cohesion and unconfined compressive strength of the rock mass were estimated. A comparison of the results using different classification methods (Q, RMR, GSI, RMi, Ramamurthy’s) was made to estimate the range of variations in the mechanical properties with the considerations of: i) the quality/quantity of the geological data; ii) the technique for partitioning of the rock mass into homogeneous domains; iii) the sensitivity and subjectivity of the empirical methods; and iv) the need for validating the empirical methods against a test case. Cet article présente les résultats d’un projet visant à établir une méthodologie, pour déterminer, de façon empirique, les propriétés mécaniques de la masse rocheuse. En utilisant les corrélations disponibles dans la littérature, quelques-unes des propriétés de la masse rocheuse ont pu être déterminées (module de déformation, angle de friction, cohésion, force de compression illimitée). Une comparaison des résultats obtenus par différentes méthodes (Q, RMR, GSI, RMi, de Ramamurthy) a permis d’établir une échelle de variations des propriétés mécaniques et de formuler une série de recommandations concernant : i) la qualité/quantité des données géologiques ; ii) la technique de partition de la masse rocheuse dans des domaines homogènes ; iii) la sensibilité et la subjectivité des méthodes empiriques ; iv) la nécessité de valider les méthodes empiriques à l’aide de nouvelles études de cas. Dieses Paper präsentiert die Ergebnisse eines Projekts mit dem Ziel, eine Methodik für die empirische Festhellung von mechanischen Eigenschaften im Gesteinmassiv zu etablieren. Durch Verwendung der in der Literatur zugänglichen Korrelationen, wurden einige Eigenschaften des Gesteinmassivs festgestellt (Entstellungsmodul, Reibungswinkel, Kohäsion, unbeschränkte Kompressionsstärke). Ein Vergleich der Ergebnisse unterschiedlicher Methoden (Q, RMR, GSI, RMi, Ramamurthy’s) wurde durchgeführt und dies erlaubte die Feststellung der Variationsskala von den mechanischen Eigenschaften, sowie eine Reihe Empfehlungen für: i) Qualität/Quantität der geologischen Dateien; ii) die Technik für Teilung des Gesteinmassivs in homogene Domäne; iii)die Empfindlichkeit und Subjektivität der empirischen Methoden; iv) das Bedarf die empirische Methoden gegen neue Fallgeschichten zu validieren.

Jan 1, 2003

By Piotr M. Kapias

Keywords: extraction, lead refining, Pb-Tl solutions, PbCl2-TlCl solutions. The theoretical part of the paper presents an analysis of the conditions of Tl extraction from Pb using different extractants and determines the activity coefficients in liquid solutions of Pb-Tl and PbCl2-TlCl. The dependence of the solution activity coefficients upon the composition and temperature is presented in the form of Krupkowski and Krupkowski-Fitzner equations. An analysis and evaluation were made of the influence of the methods of PbCl2 introduction into a Pb-Tl solution upon the efficiency of the Tl extraction process under thermodynamic equilibrium conditions. The analysis made it possible to formulate relevant equations describing the dynamics of the process of Tl extraction from Pb under stirring conditions as well as under the extractant injection into the liquid Pb-Tl solution conditions. In the part concerning experimental work, results are given for tests on the Tl extraction process from Pb-Tl liquid solutions of initial Tl content of approximately 0.05% mass using PbCl2 or, alternatively, Cl2(g) conducted in laboratorial scale. The tests made it possible to establish the influence of time, temperature, mass and the method of introducing the extractants into the liquid upon the level of Tl extraction from a Pb-Tl solution. Labels used in the text. WT1m - TI content in metallic phase, % mass WT1s - TI content in chloride phase, % mass wpTlm - TI content in metallic phase in initial state, % mass W°Tlm - TI content in metallic phase in equilibrium conditions, % mass m°m - initial mass in metallic phase mm - mass in metallic phase mPbC12 - lead chloride mass fed to the system MPbC12-TIC1 - mass in chloride phase MPb - lead atomic mass, g/mole MT1 - thallium atomic mass, g/mole K - Nernst distribution coefficient Xi - mole friction of solution component X°PbC12 - mole friction of PbC12 in saturated solution X°T1C1 - mole friction of T1C1 in saturated solution T - temperature, K R - gas constant, J/(mole K) k - kinetic equation constant, 1/(%-min.) ?i - solution component activity coefficient e - extraction rate, %

Jan 1, 2008

By H. L. Zimba

Flotation involves the selective levitation of mineral and its transfer from cell to launder. The flotation rate is the rate of this transfer. It may be defined by the slope of a recovery-time curve for any cell in a bank or at any time in a batch operation. The objective in flotation rate study is an equation expressing the rate in terms of some measurable property of the pulp. This can be either the concentration of floatable mineral in weight per unit volume or a relative concentration, which will be a function of the recovery. A rate equation for an actual flotation pulp will contain at least two constants, both to be determined from the collected data. The data used in this paper were collected from bench-scale flotation tests on Konkola primary mill cyclone overflow at various pulp densities and pre-flotation thickener underflow at a pulp density of 35% solids by weight.

Jan 1, 2009

By D. J. de Clerk

Global trends stipulate the need to optimize existing assets while reducing environmental impacts. This paper illustrates the procedure that was followed to achieve such goals at one of the coal burning flash dryer units at an Anglo American smelter. An in-depth study of the process and related literature led to the development and installation of a revised control philosophy. This system includes modifications to the existing regulatory control structure as well as a hybrid rule-based and model-predictive advanced process control (APC) layer. Since commissioning of the APC, this flash dryer?s average throughput has increased by more than 6%, despite higher feed moistures. Furthermore, even though coal consumption has increased slightly, operating efficiency has improved by close to 5%. This was made possible by improving stability of the drying column outlet temperature by approximately 40%, which in turn enabled selection of a more optimal setpoint. Recent data has shown that APC utilization now exceeds 95%. This is indicative of a successful controller installation with good site acceptance. The same philosophy has therefore since been rolled out to most of the other flash dryers in the group.

Jan 1, 2012

By M. Dobbins

Magnetic separation has long been used to upgrade and beneficiate a wide variety of industrial minerals. Advances in both wet and dry magnetic separators over the years has broadened their use, and questions are often raised about which separation technique or equipment type is most appropriate for a particular operation. This paper will provide a brief look at existing magnetic separation technologies, and discuss their potential advantages and disadvantages when applied to heavy mineral applications. Relevant case studies for the separation of ilmenite and chromite are then presented. The process development efforts undertaken for each case are described, and the rationale for selecting appropriate magnetic separation technology is explained. The nature of the material being treated must clearly be understood, knowledge and access to testing the best separation technologies is required, and careful process development and economic evaluations are a must. As is shown in the case study discussions, it is imperative that these principles drive the separation technology selection and placement, rather than looking at typical or existing similar flowsheets as rules. As examples, the ilmenite tailings case study presented in this paper shows how advances in technology have allowed for increased recovery of -45 µm ilmenite by utilizing a multi-stage SLon® wet magnetic separator circuit equating to an additional 30 000 tons of ilmenite produced per year. The virgin chromite case study presented shows that through careful testing and circuit design efforts using RED technology, a 20% increase in overall chromite recovery was achieved over previous demonstration work.

Jan 1, 2007

By M. Steyn

Until 2000, pricing involved profit taking and cost covering combined with limited global published information. Market information was mostly subjective in nature and large resource companies benefited exclusively from aggregated company information and data. The market constituted producers and consumers only. The nineties saw massive cost cutting drives and re-engineering initiatives and this underwrote the structural changes evident in the late 1990s? economy. This supported South African producers on the international FOB cash cost curve, and ensured profitable coal mining operations. As the debate on relative scarcity of fossil fuels ensued, producers and buyers looked to the developing terminal coal market for direction. The much needed direction was provided when the API coal indices were developed and derivative trading was embraced to include financial institutions, trading houses and hedge funds. The liquidity of coal trades increased rapidly and vastly and market information became obtainable on a daily basis. Interpretation of current and future coal prices became available to all market players and contributed to the sophistication of the market that is now able to participate in risk management of prices, capital expenditure and brownfield developments.

Jan 1, 2010

By P. J. Foster

This paper summarizes a behavioural safety project undertaken in seven quarries in the UK in order to investigate its applicability as a means of raising the standards of health and safety in the UK quarrying industry. A behavioural safety methodology was developed and trialed at two quarry sites in the UK. During the study the number of unsafe acts and minor accidents had decreased and at one of the quarries there was a 95% reduction in the number of working days lost. It was then introduced at a further five sites of varying sizes and within this focused specifically on lone workers as well as behaviours that affected quality and environmental issues. Positive improvements were noted in most of these operations. The project also looked at the effectiveness of health and safety performance indicators. Here, the common lead and trailing indicators for both safety and health that are commonly used by industry were identified. In consultation with the UK quarrying industry these were then used to identify specific performance measurement criteria that can be used by the quarrying sector to measure performance. Following on from this, a quarry specific health and safety management system specification was developed for large and small quarries.

Jan 1, 2008

By Steve Konieczki

[ ] Great Basin Gold Ltd. (GBG) owns the Hollister Mine and operates it through the wholly owned subsidiary Rodeo Creek Gold, Inc. The property is located in northern Nevada on the Carlin Trend gold belt within the historic Ivanhoe Mining District. The mine is located on the western edge of the Northern Nevada Rift, a major north-northwest trending structural zone that has localized middle Miocene volcanic rocks and numerous epithermal gold deposits. The precious metal deposits are low-sulfidation epithermal systems characterized by banded quartz veins with electrum and silver selenides. The Hollister Mine will employ the selective underground mining method of cut and fill. This will be combined with split shooting (resuing mining method) to optimize recovery and reduce dilution. The focus of mining will be on extraction of ?ounces? from the narrow-veins rather than trying to maximize tons. The initial drifts will be excavated along the strike of the vein and then capped with a substantial concrete sill pillar. Back stoping with hand held drills will be used to selectively mine the vein. The stopes will be backfilled with waste rock material. With every lift, an 18 inch concrete cap will be poured onto the backfill waste rock to prevent gold values from being lost into the fill. Targeted ore production rate will be over 400 tons per day. With current ore reserves, project life is estimated to be around eight years; however, Hollister geologists view the site as one of the most prospective systems for bonanza vein deposits in Nevada. Approximately $14

Jan 1, 2008

By J. Tikka, E. Bäcklund, N. -O. Lindfors

Tornados are the most violent weather events in the world, and we have all seen the forces and phenomena created by tornados in nature. Airgrinder AB has been working with a material treatment technology, which most easily could be described as an artificial tornado. The process consists principally of one air fan providing a high-velocity airstream that enters a mechanical cyclone. When the gas enters the cyclone, an outer vortex is created. This outer vortex rotates next to the cyclone wall, and at the bottom of the cyclone funnel the gas stream is turned and an inner vortex is created. The control of the air flow is tuned by a special device on top of the cyclone. The gas outlet is at the top of the cyclone and the material outlet at the bottom. The material is fed through a feeding device into the air stream channel prior to the inlet into the cyclone. The process is basically an improved grinding and dehydrating system, which is very efficient and environmentally friendly and can even be employed with very sticky materials. Also due to its rotating comminution, the material particles become rounded during grinding, hence more free flowing and easier to handle. MEFOS has already tested more than 30 different applications in the pilot equipment. The materials tested range from metallurgical slags containing 2?3% moisture to sludges with up to70% moisture. This technology has a potentially strong impact on mineral beneficiation, including the drying of sticky fine-grained materials, improved and selective gas scrubbing and the manufacture of free flowing powders.

Jan 1, 2007

Metso Minerals Process Technology Asia-Pacific (MMPT-AP) has been working with many mining companies worldwide performing `Mine to Mill' or Process Integration and Optimisation (PIO) studies. MMPT-AP has developed a proven methodology to improve the efficiency of the mine-mill interface and gain maximum benefit. The PIO methodology involves rock characterisation, mathematical modelling and simulation to generate a list of operational and control changes for both the mine and concentrator. Following the methodology, the list of recommendations is developed relatively easily; the more challenging part depends on the company. Success of a PIO project relies on the ability of an organisation to implement change - both operationally and culturally: the human element. When a PIO project is started, there is initial interest and commitment from the company. But how can this be maintained? How does an operation know if the benefit continues? MMPT AP is now developing long-term relationships with clients to ensure that the increased production and improved efficiency continues. Direct and indirect measurements are used to determine the key factors involved and to understand the cause/effect relationships. Simulation tools also can be used to compare current with recommended practices - so when material properties vary over time, the benefits can still be quantified. PIO is about empowerment: by measuring and understanding what parameters affect concentrator performance, the site personnel now have the knowledge to make a difference. Rather than simply reporting variable or poor concentrator performance, operations can predict when production will be affected and put controls in place to prevent it from happening. This requires support and commitment from the company or `buy in'. Ensuring this buy in continues is the challenge facing every company involved in PIO work - but the benefits are well worth it. This paper will review MMPT-AP's experiences in implementing PIO projects in the long term: from both the consulting and operational viewpoints. MMPT-AP's involvement with a number of companies will be discussed as examples of what works and what does not.

Jan 1, 2007

By F. T. Cawood

Despite economic law and policy instruments with righteous intentions, the politics of resource nationalism could render these instruments unworkable. South Africa is a case in point. After the establishment of democracy, the country's outdated law and policy framework was replaced with a modern system, and in many respects an exemplary one. Converting the privately-owned mineral right system into a scheme of state custodianship allowed for several resource nationalism instruments, in addition to a resources royalty structure that first, compensates for the loss of a non-renewable resource; second, provides for optimal resource use through encouraging value addition to mineral production; and third, effectively targets economic rents. However, despite these improvements, the country went through a process of fierce debate on whether or not mines should be nationalized: the debate was fuelled by public anger with claims of political non-delivery. The result was considerable noise because of public unawareness of facts and distortion of the facts in political rhetoric. The purpose of this article is, first, to establish the status of resource nationalism in South Africa's mineral and fiscal frameworks; second, to give an opinion on the findings of the African National Congress's document on state intervention (Maximising the Developmental Impact of the People's Mineral Assets: State Intervention in the Minerals Sector (SIMS), 2012); and third, to fruitfully contribute to the fundamental discussion on how South Africans benefit from their mineral riches. The methodology is to start with explaining resource nationalism as an international issue for the extractive industries; then to offer an overview of existing resource nationalism instruments in South Africa-along with their effectiveness in attracting rents and investment. The major finding is that South Africa has resource nationalism firmly ingrained in its current suite of instruments. However, it is necessary to address the perceptions of bad governance, and above all, maintain the stability of the rules governing mineral development in South Africa.

Jan 1, 2013

By C. Birch, M. Katuruza

"The purpose of this study was to demonstrate unmanned aircraft system (UAS) technology in opencast highwall mapping using the experience at Isibonelo Colliery in Mpumalanga Province of South Africa. In opencast mines, geological mapping has evolved over time and there have been challenges in extracting valuable information from exposed highwalls due to restricted access for safety reasons. A UAS was used at Isibonelo Colliery to conduct highwall mapping, using drone-based digital photogrammetry techniques. A demonstration survey was undertaken during February 2018. The highwall flyover demonstration was planned for two areas (North and South pits) where field control points were placed by the mine survey department. A contractor used a DJI Phantom 4 (Pro) for the highwall mapping. Raw data was processed within 48 hours and a 3D model of the mapped pit area was produced. Further data extraction included obtaining updated weathering and lithological contact elevations and thicknesses for use in short-term planning. The results showed a good correlation between the resource model and the UAS data model. The project was considered a success and highwall flyover mapping and is now standard practice at Isibonelo Colliery.IntroductionDetailed geological mapping is crucial to the understanding of the structure of any mineral deposit. Several mapping methods may be applied depending on the available exposure/outcrop and nature of the orebody; for example, coal deposits typically suboutcrop only, therefore an opencut highwall provides the best exposure for mapping the geology. Mapped information, when incorporated into a resource model (generated from exploration borehole data), improves the understanding of the orebody or coal seam. This research paper focused on the use of unmanned aircraft system (UAS) technology for pit highwall mapping to generate data for updating geological models and avail the latest information to mine planning to improve the short-term plans."

Mar 1, 2019

YEAR 1943-1944 Vol. 44 Page A major change-over in the ventilation of a deep level mine, by F. G. Hill and E. C. Ranson, 27; Discussion 56, 62, 67, 71, 72, 79, 123, 129 131 A note on the quarrying of surface limestone in the Sinai Desert, by V. L. Bosazza.. .. 59 Mining with diamond drills at the Nkana Mine of the Rhokana Corporation, Limited, Northern Rhodesia, by W. A. Odgers and A. G. Stirling, 95; Discussion 117, 121, 122 123 On silicates and dusts from the Witwatersrand gold mines (some preliminary notes), by J. J. Frankel, 169; Discussion .. 178 Presidential Address-Review of the rock pressure problem, by C. Biccard Jeppe, 3; Discussion 11,15 17 The chemistry, production and application of plastics, by P. N. Lategan, 138; Discussion 151 153 YEAR 1944-1945 Vol. 45 Page A microtechnique for the size-grading of mine dust, by S. R. Rabson, 34; Discussion 49, 50, 52 55 Activated carbon for regenerating used lubricating oil, by F. J. Tromp and J. J. Matthee 90 A contribution to the study of the production of zeolites, by C. C. le Grange and A. J. Petrick 235 A laboratory method for the determination of the suitability of South African coal and coal blends for the manufacture of metallurgical coke, by R. F. J. Teichmann .. .. 202 Copper containing cements for self-sanitising surfaces, by R. S. Young and H. L. Talbot 156 Notes on some sulphide minerals from the Far East Rand, by E. Mendelssohn, 84; Discussion, 88 89 Presidential Address-A review of underground support on the Witwatersrand with its Bearing on the Problem of ultradeep mining, by P. J. Louis Bok, 3; Discussion, 24, 25 27 Scientific management with particular application to a Witwatersrand gold mine, by J. S. Ford, 63; Discussion, 77, 80, 82 83 Some aspects of rock-drilling practice (the Witwatersrand gold field), by C. J. Irving, 163; Discussion, 185, 190 *197 Temperature measurements in a mine on the Witwatersrand with an electrical resistance thermometer, by O. Weiss, 127; Discussion, 136 137 The measurement of the geo-thermic gradient by means of the clinical thermometer, by R. A. H. Flugge-de Smidt, 105; Discussion, 136 137 The micro-chemical determination of free and combined silica in mine dust, by S. R. Rabson, 43; Discussion, 49, 50, 52 55 The oxidation of pyrites associated with South African coals, by R. F. J. Teichmann 141 YEAR 1945-1946 Vol. 46 Page Air cooling plant, No. 4 Shaft, City Deep, Limited. A review of layout and results achieved, by H. W. Unwin, A. Malcolm and R. E. Campbell Pitt, 66; Discussion, 100, 102, 103, 106, 110 115 A preliminary note on the Waterberg coal field as a possible source of coking coal, by P. E. Hall 124

[Consider a square block W in an ore body S2, to be valued from one centre sample w, and one corner sample w2 (Fig. 9.1). The sample set is ws = Iw,;w21. We can estimate the block average µw by the average of the sample values x, and x2: µw = 'z (x, + xz). (9.1) The error made is measured by the estimation variance: o' (ws to W) = 2 - (ws; W) - - (ws;ws) - - (W; W). (9.2) However, we know that the centre sample w, gives more information about the block value than the corner sample w2. In the example studied in § 8.4, where w, and w2 were considered to be points, we found that of (w, to W) was nearly one third smaller than o2E (w2 to W), therefore when estimating W one should give more weight to w, than to w2. In general, when evaluating a block W from a set of n samples ws, where WS = l w;w2; ... wn1, a better estimator of µw can be obtained if we give different weights to the sample values, depending on the size and the positions of the samples. Some desirable properties of such an estimator µw are: ? It should be a linear function of the sample values xi: n µw = bi xi (9.3) =t where bi = weight given to sample x . ? It should be unbiased, i.e. its expected value should be equal to the true block value: E [µw - µw] = 0. (9.4) ? The mean squared error of estimation of µw should be a minimum E [(µw - µw)2] = a minimum. (9.5) The estimator which satisfies these properties is a minimum variance, linear and unbiased estimator, and is known as the kriging estimator. The corresponding error of estimation is the kriging error. This estimator is also known as the BLUE (for Best Linear Unbiased Estimator) estimator. This was named by Matheron in acknowledgement of the early work of Krige's in the optimization of the evaluation of the South African gold mines. The following notations will be used: µK kriging estimator. o2k = o2K (w,, to W) kriging error.]

Jan 1, 1978

By B. Mulcahy, M. Valenta

"The purpose of executing a project in a stagewise fashion is to evaluate all potential options in a cost-effective manner and develop an understanding of the project drivers, thereby minimizing overall project risk to the client. Among the more valuable tools for this exercise are production and financial models that can be used to quantify the sensitivity of the project to the critical parameters.The mine and concentrator used in this case study are located on the Kalahari Copper Belt, which extends from Zambia through northern Botswana into Namibia. This area of Africa has seen very little industrial development and the project will create much-needed employment and development in the region.The success of this project thus far can be attributed to the close cooperation between the geological, mining, and metallurgical disciplines. Regular updates of projected capital and operating cost estimates coupled with project outputs guided the teams in optimizing their various discipline models, ultimately delivering a compelling argument for the execution of the project. Key to the success was the development of a geometallurgical model for the prediction of concentrate tonnage, grade, and recovery for the life of the mine from the mining plan.This paper summarizes the metallurgical findings and the outcome of the various project stages. The development of the model is discussed, as are the challenges faced in developing a suitable metallurgical process route. IntroductionThe Kalahari Copper BeltThe Kalahari Copperbelt, which extends from Zambia across northwest Botswana into Namibia, is considered to be a broad time equivalent of the Central African Copperbelt, with a similar style of mineralization. However, at shallower depths (<25 m), chrysocolla and malachite exist in significant proportions in certain geological areas. As illustrated in Figure 1, the project is located in the Ghanzi-Chobe Fold Belt which forms part of the Kalahari Copper Belt. The Ghanzi Group, which overlies the lowest stratigraphic unit (the Kwebe Formation), consists of three formations, namely the Ngwako Pan, the D’Kar, and the Mamuno Formation (Hall, 2012)."

Jan 1, 2016

By S. M. Rupprecht

"Artisanal mining is basic mining characterized by manually intensive work methods utilizing primitive or simple equipment and conducted by individuals or small groups exploiting deposits. Artisanal mining in Rwanda and Burundi is further complicated in that the techniques applied are often inadequate, resulting in low productivity and poor recoveries, and workers are paid low wages with owners reluctant to reinvest in the mining operations. A consequence of this vicious circle is often poor working conditions, with miners operating under unsafe and/or unhealthy working conditions. An additional problem is that mining is conducted in a manner that is detrimental to the environment.Artisanal mining is commonly more dangerous than large-scale modern mining operations. Artisanal operations are generally subsistence activities with the miners focusing more on immediate concerns than the long-term consequences of their activities. When miners have no other source of income, they will usually find ways to evade controls and carry on working. Machinery tends to be expensive and often far beyond the reach of most artisanal miners, and therefore there is a general tendency for workers to focus on labour intensive and riskier mining methods.This paper proposes the introduction of small-scale mechanization with labour-intensive manual mining utilizing a bench mining approach in artisanal mines operating in Central Africa. From the 1950s to the 1980s bench mining was successfully conducted in Burundi utilizing manual labour. In order to achieve a balance between job creation and project economics, the combination of manual and mechanized mining is proposed. Manual mining offers the benefit of local job creation while ensuring good mining techniques, such as minimizing mining loses and dilution. Through the introduction of mechanized loading and hauling activities, areas of high stripping ratios can be viably mined, thus increasing the amount of resources that can be exploited. The use of a loader and tractor-trailer arrangement is proposed, thereby improving throughput, productivity, and worker safety and, reducing the impact on the environment."

Jan 1, 2017

By V. L. Nkuna, S. R. Amos, T. Naidoo

"Ivanhoe Mines’ Kamoa copper project is a recently discovered high-grade copper sulphide deposit in the Katanga Province of the Democratic Republic of Congo. The mineralization identified to date within the resource is typical of sedimentary-hosted stratiform copper deposits and comprises three distinct units: supergene, mixed, and hypogene mineralization. Since 2010, various metallurgical test work campaigns have been conducted on drill core from different areas within the deposit in line with resource expansion. The most recent bench-scale flotation test work has shown positive repeatable results. The work was conducted on a composite sample of drill core from the southern part of the Kamoa resource. The sample is representative of the first four to five years of planned production, when Ivanhoe Mines intends to produce clean, highgrade copper flotation concentrate. A detailed test work roadmap developed from first principles for the campaign led to an optimum flow sheet for treating the Kamoa mineralization. Copper recoveries of 88.3%, at a concentrate grade of 39.0% copper, were achieved using a composite sample — an improvement on the previously published 85.9% life-of-mine average copper recovery indicated in the November 2013 Kamoa Preliminary Economic Assessment. IntroductionThe Kamoa project is a newly discovered, very large, stratiform copper deposit with adjacent prospective exploration areas within the Central African Copperbelt, approximately 25 km west of the town of Kolwezi in the Democratic Republic of the Congo (DRC) and about 270 kilometres west of the provincial capital of Lubumbashi. Ivanhoe Mines holds its 95% interest in the Kamoa copper project through a subsidiary company, Kamoa Copper SA Limited SPRL, and DRC government owns 5%. The project location is indicated in Figure 1.In January 2013, a new independent mineral resource estimate ranked Kamoa as Africa's largest high-grade copper discovery and the world's largest undeveloped highgrade copper discovery. At this time, Ivanhoe Mines had estimated discovered Indicated Mineral Resources of 739 Mt grading 2.67% copper, containing 43.5 billion pounds of copper, and Inferred Mineral Resources of 227 Mt grading 1.96% copper, containing 9.8 billion pounds of copper, as demonstrated in the Preliminary Economic Assessment (PEA) (AMC, 2013). A 1% copper cut-off grade and a minimum vertical mining thickness of 3 m were applied in each classification."

Jan 1, 2016

By P. R. Jochens, D. D. Howat, C. W. Wolhuter

Prof D. D. Howat (Member): I am a man with a grievance this afternoon. The other authors of the paper entered into a conspiracy to ensure that I presented the paper, and finally even had the audacity to say that this was the least that could be expected from me as I had done so little of the other work. Looking at the distinguished audience here that includes some figures who have forgotten more about cement that some of us have ever learned, I realise how right the other authors were. I feel very much cast in the role of the fool who was pushed in where angels fear to tread. I hesitate to say, Sir, that I would not use the word angels in any definition of the authors of this paper. In presenting the paper, may I try to put forward a few simple points about cement that are probably as little known to the majority of the audience as they were to me-at least until very recently. Concrete, made by mixing Portland cement, sand, crushed rock and water is the most widely used constructional material in the world. Generally the production of actual Portland Cement is about two-thirds that of steel and by the time this is formed into concrete the total is about five times the world tonnage of steel produced. A very rough approximation suggests that world consumption of concrete is about one ton per person per annum. Apart from fresh water mankind consumes no other material in such quantities. What mankind originally required was a mortar to be used for joining blocks of stone or bricks. Such mortar was originally made from limestone burned in a kiln and then mixed with water. Production of mortar of this type began over 5,000 years ago. Some samples from pyramids in Egypt have shown this mortar to be in good condition although over 4,500 years old. The progress of technological development was very slow until 1824 when an English bricklayer, Joseph Aspidin, patented a new mortar material which he made by burning limestone and clay together in his kitchen stove. Aspdin called his product &apos;Portland Cement&apos; because, in colour, it resembled a well-known building stone quarried in the Isle of Portland on the south coast of England. Aspid&apos;s same types of raw materials are used today in modern cement production and the product is still referred to as Portland cement. A lime-containing material such as chalk or shell and a clay-type material such as shale, slate or clay itself, are mixed in the required proportions, ground and fed to a kiln where the minimum burning temperature is about 1,500°C. The raw materials react to form hard chunks of a material known as &apos;clinker&apos;. About 5 per cent of gypsum is added to the clinker and the mixture is then ground to a very fine powder, the function of the gypsum being to control the rate of setting of the concrete. The key oxides in cement production are lime, silica, alumina and iron oxide. The possible reactions occurring during and the products of the burning process are shown in Table I.

Jan 12, 1968

A large body of work exists discussing the impact of grinding media on mineral flotation. Generally, the work indicates that a change to a less electrochemically active grinding environment has positive benefits on downstream processing. There is a fear, however, that these benefits may not be realized when treating low sulphide containing ores, typified by UG2 style deposits. A series of experiments was developed to test the flotation response of UG2 ores using the Magotteaux Mill® to determine if measurable differences in the pulp chemistry could be discerned using a range of grinding media types. Further, the flotation responses of the contained sulphides (chalcopyrite, pentlandite and pyrrhotite) were determined. The data collected provided strong evidence that the grinding environment can significantly influence the pulp chemistry and flotation characteristics of all sulphide minerals, even when the ore contains less than 0.5 per cent total sulphide. The results show that the change to an inert media type produced a substantial improvement in the flotation rate of all sulphide minerals, as well as the PGMs.

Jan 1, 2009

By D. Vogt

"Rock has been cut in the process of mining since before the invention of explosives. Today, we seek to return to cutting to reap the benefits of continuous operations for South African underground hard-rock mines, to improve speed of access to the orebody, and to improve the efficiency of mining operations.Development of new technology fits within a framework of engineering knowledge. By understanding the characteristics of the rock, the tools we use to cut it with, and the history of mining and rock cutting, we can see the genesis of the road-header, the longwall, and the continuous miner, all drag bit cutters. They have emerged as the solutions of choice for underground mining of softer materials such as coal and potash. In hard rock, the challenges are the forces required to break the rock, and the wear of the tools caused by the rock’s abrasiveness. Only disc cutters currently handle the challenges, and even then, often not economically. New materials like thermally stable diamond composite will help, as will combinations of mechanical cutters and other methods such as high-pressure water or high temperatures.It is not clear what will emerge as the consensus technique for hardrock cutting. Experience teaches that development is expensive and the market is small. Will mining companies partner with equipment developers to make the technological leap? Or will the solution come from a systems approach, not considered here?IntroductionBlasting is the dominant method of breaking rock for the purposes of mining. When used underground, blasting is part of a batch process. If rock can be cut rather than blasted, mining can become continuous, leading to process and efficiency improvements.Coal produced from underground mines is now predominantly excavated using mechanical means, but underground hard rock is still broken primarily by explosives.This paper traces the history of rock cutting, reviews the main physical processes that are or could be used, and comments on the future. It is written from the perspective of narrow-stope hard-rock mining typical of South African gold and platinum mines."

Jan 1, 2016