Search Documents

By H. Manurung, I. M. Bendiayasa, W. Astuti, and H. T. B. M. Petrus, F Anggara, K. C. Wanta

The leaching kinetics of cerium (Ce) and yttrium (Y) in sodium-hydroxide-digested non-magnetic coal fly ash using acetic acid were investigated. The variables analysed were pH, solid-to-liquid ratio (S/L), and temperature. The results show that cerium and yttrium's maximum recovery was 57.33% and 58.36%, respectively, under leaching temperature of 90°C for Ce and 60°C for Y at pH of 1,74 and 10 g/mL solid-liquid ratio in 240 minutes. Increasing the leaching time to more than 120 minutes did not significantly improve the results. After the magnetic separation process, the ICP-OES analysis shows a slight increase in the concentration of cerium and yttrium on nonmagnetic components. The XRD and ICP-OES analysis for the sample before and after silicate digestion shows that 40% silicate was dissolved. The calculation of apparent activation energies of leaching using the Arrhenius law for the leaching of cerium and yttrium gives 22.72 kJ/mol and 35.84 kJ/mol, respectively. The kinetic leaching model of cerium and yttrium all fit Dickinson's new shrinking core model. The calculation results show that the leaching reaction is controlled by combining interface transfer and diffusion across the product layer.

Nov 6, 2024

By Y. Ren, B. Yang

The magnetic field characteristics due to electromagnetic stirring in the secondary cooling zone of an extra-thick slab during continuous casting are numerically determined using Maxwell's equations, with particular emphasis on the distribution of magnetic induction intensity and electromagnetic force, as well as the influence of process parameters on the magnetic field. The orientation of the electromagnetic force is the same when the electromagnetic stirrers at the 30° and 60° posistions of the arc-shaped slab are powered in the same direction; otherwise, the orientation is opposite. The magnetic induction at the centre of the section of the stirrer's central axis at the 30° positio, as well as the current, frequency, and fitting formulae, are as follows: B = {0.075I.(1/A)-0.3} mT and B = {-1.75f.(1/Hz)+22} mT. The electromagnetic force and current fitting formula at the central point of the B-B section is F = {0.03168I2.(1/A2)-03.762I.(1/A)+326.7} N/m3, and the fitting formula of electromagnetic force and frequency at the centre point is divided into two segments. The first takes the form of a parabola: = {-21((f-4.3).(1/Hz)2)+970} N/m3, and the second segment is negative linear: F = {-1.65f.(1/Hz)+51.5} N/m3.

Apr 16, 2024

By K. G. Lomberg

The density used to covert volume to tons is critical in determining the real in-situ tonnage of Mineral Resources. However, the methods used to determine density and the use of different technical terms are seen to be inconsistent throughout the industry. Probably the best discussion addressing the determination of density was presented by Lipton (2001). This paper does not try to replicate this excellent work, but rather to review current industry practice and present a comparison of the approach to density in public reporting. Some of the technical terms used in reporting and the common methods applied are also discussed.

Sep 1, 2021

By M. Asghari, R. Amiri, A. Haratian, S. Haji

The aim of this investigation is the evaluation of optimising the Shahroud copper ore beneficiation plant near the Iranian city of Shahroud, by means of a sensor-based ore sorter applying X-ray transmission technology. Currently, this plant’s feed capacity of 52t/h produces 0.5t/h copper concentrate with a grade of 30% and copper recovery of 85% from a feed grade of 0.36%. By applying an X-ray transmission-based (XRT) sorter, it is possible to preconcentrate the feed and remove the gangue materials before entering the plant, enabling the production rate of concentrate to be increased. In this study, the obtained representative sample from the plant was preconcentrated in particle size of - 75+10mm by using the X-ray sorter, thus the concentrate with Cu grade of 0.85% was obtained. Therefore, by using of X-ray sorter the Cu grade of plant feed was increased to 0.48%. By increasing the feed grade from 0.36% to 0.48%, and considering a Cu recovery of 85%, the production rate will be increased from 0.48t/h to 0.61t/h. Therefore, the preconcentration by using the XRT sorter increases the production rate by 27%. Keywords: Optimisation, preconcentration, copper, X-ray, sensor-based ore sorting

Jan 1, 2020

By C. Karageorgos, J. Sakala, A. Prinsloo, B. Ngambi

The sulphide flotation circuit at First Quantum Minerals’ Kansanshi mine in Zambia produced over 100,000 t of copper in 2019. For this circuit, mineralogical analysis has shown that the majority of the copper lost is hosted in fine liberated chalcopyrite, which is a paramagnetic mineral. The objective of this work was therefore to improve fine chalcopyrite recovery in the sulphide flotation circuit at Kansanshi, using a magnetic conditioning technology to agglomerate fine paramagnetic minerals. This theoretically increases the probability of attachment during collision and therefore improves recovery. A four-month paired ‘t’ test plant trial was carried out and comprised of consecutive ON-OFF periods with and without magnetic conditioning in the rougher flotation bank of the sulphide circuit. The experimental design involved assessment of recovery by size based on daily and weekly composite samples of feed and tails, sized using both wet-screening and cyclosizer. Both the daily plant data and the sized samples showed an increase in Cu recovery with magnetic conditioning ON. A 0.56% copper recovery improvement was measured with magnetic conditioning at a 99.4% confidence level. Keywords: Flotation, fine mineral, chalcopyrite, magnetic aggregation

Jan 1, 2020

The nature of metallurgical engineering?applying and optimising chemical and physical processing of ores into useful materials?is reviewed. Important trends that shape the context in which metallurgical engineers practise are identified ? increased global production of primary metals, declining prices, environmental constraints, and increased property requirements of materials. A successful department of metallurgical engineering is one which employs a team of academic leaders to develop graduate engineers who are productive across the full range of metallurgical processing. Keywords: metallurgical engineering, primary metals, commodity prices, processing

Jan 1, 2003

By I. Serepa, N. C. Steenkamp

Investigations were conducted to determine the condition and stability of the existing decline at amine in the Kalahari Manganese Field, Northern Cape Province, South Africa. During the inspection of the decline, voids were identified behind the concrete lining on the hangingwall and sidewalls over a total linear distance of 230 m. The voids did not provide confinement and, as a result, self-mining was occurring behind the lining. Water was flowing into the decline, over a total linear distance of 100 m, at areas where the decline intersected incompetent rock units, causing softening of the concrete lining and deterioration of the surrounding rock mass. Further damage to the concrete lining was caused by expansion and contraction of the wet red clay unit. Remedial work comprised void filling and water sealing to prevent further deterioration of the decline and ensure that it remained operable for the remainder of the life of mine. Void filling was accomplished by drilling rows of holes along the decline to access the voids and filling the voids with foam. This was followed by the sealing with polymer fluids. Telescopic pipes were also installed to allow water to drain off. A visual inspection was conducted and check-holes were drilled to assess the quality of the remedial work. The void filling material had penetrated cracks in the concrete lining, and areas where voids were intersected by check-holes were re-filled. Additional holes were drilled to re-seal areas that were still wet. The remedial work was completed successfully, as all voids were filled and stability achieved without compromising the concrete lining. The ingress of groundwater was also reduced to some residual dampness.

Mar 2, 2022

By K. H. Zhang, Y. P. Gao, J. Q. Zhao, Q. Li, J. C. Ma

Compared with sinusoidal oscillation, non-sinusoidal oscillation enhances the ability to control waveform and meets different oscillation requirements by adding an independent parameter, which is the key technology for high-efficiency continuous casting. A new waveform of mould non-sinusoidal oscillation is proposed in this paper, that is, a velocity waveform that is composed only of straight lines and parabolas, which not only has good dynamic characteristics, but also further enhances the feature of non-sinusoidal oscillation. Compared with sinusoidal oscillation, the negative strip time is reduced by 15.9%, the maximum negative strip velocity difference is increased by 38.3%, and the maximum positive strip velocity difference is decreased by 27.8%. The formulas of oscillation process parameters can be clearly deduced, and the isoplethic curves of oscillation process parameters when multi-parameter simultaneously changes are drawn. The negative strip time decreases as the modification ratio, frequency, and casting speed increase, but increases as stroke increases. In order to maintain the stability of negative strip time, an oscillation synchronous control model for optimising oscillation basic parameters was developed. Through practical application, the mean oscillation mark depths decreased by 10.1 μm and the flux consumption is increased from 0.37 kg/t to 0.45 kg/t in the non-sinusoidal oscillation model, which meets the requirements of normal production.

Oct 24, 2025

By Y. Tanaka, H. Miki, Y. Aoki, H. Okamoto, G. P. W. Suyantar, T. Hirajima

Due to environmental limitations and the scarcity of freshwater, flotation using seawater or desalinated seawater as process water becomes more common for mining operations. On the other hand, seawater has been reported to affect the flotation behavior of sulfide minerals. Few reports are available on influence of pyrite depression, recycled seawater and lime consumption on flotation by using seawater. In this study, the flotation tests were performed using ore sample to investigate the effect of pH with seawater and process water used in plant on the flotation behavior in a laboratory-scale flotation cell and a pilot plant-scale. The results of laboratory scale flotation indicated that copper and molybdenum flotation kinetics decreased with increasing pH. Furthermore, the iron (mainly pyrite) recovery decreased with increasing pH. The pilot plant-scale flotation test showed that water with a higher concentration of magnesium and calcium (plant processes water) consumed a higher amount of lime. Because of low lime consumption and high copper and molybdenum recovery and grade, pH 8 is suitable compared with pH 8.5 for flotation. Keywords: seawater, process water, copper-molybdenum rougher flotation, pH, pilot test

Jan 1, 2020

By M. A. Mahboob, T. Celik, B. Genc, I. Atif, S. Ali

"Mapping of hydrothermally altered areas, which are usually associated with mineralization, is essential in mineral exploration. In this research, open source reflectance spectroscopy data from the multispectral moderate-resolution Landsat 8 satellite was used to map altered rocks in the Gauteng and Mpumalanga provinces of South Africa. The unique spectral reflectance and absorption characteristics of remotely sensed Landsat data in the visible, near-infrared (NIR), shortwave-infrared (SWIR) and thermal infrared (TIR) regions of the electromagnetic spectrum were used in different digital image processing techniques. The band ratios (red/blue, SWIR 2/NIR, SWIR 1/NIR), spectral band combinations (Kaufmann ratio, Sabins ratio) and principal component analysis (Crosta technique) were applied to efficiently and successfully map hydrothermal alteration minerals. The results showed that the combination of spectral bands and the principal component analysis method is effective in delineating mineral alteration through remotely sensed satellite data. The validation of results by using the published mineral maps of the Council for Geoscience South Africa showed a good relationship with the identified zones of mineralization. The methodology developed in this study is cost-effective and time-saving, and can be applied to inaccessible and/or new areas with limited ground-based knowledge to obtain reliable and up-to-date mineral information.IntroductionMany developing nations depend on exploration and exploitation of mineral resources to sustain their economic growth. Usually, the traditional mineral exploration techniques require enormous finances, prolonged time, and tremendous manpower, particularly in areas that are not easily reachable (Maduaka, 2014). Furthermore, mineral exploration required state-of-the-art techniques and expertise along with geological, geochemical, and geophysical datasets, which may not be easily available or may be lacking where access is problematic (Kaiser et al., 2002; Bemis et al., 2014). Modern remote sensing technology has proved to be one of the highly efficient and robust techniques used for mineral exploration. The use of remote sensing satellite images for geological mapping and mineral exploration usually involves studying the physicochemical properties of rocks and weathering soils, such as mineralogy, landforms, geochemical signatures, and the spatiall distribution of lineaments (Bhattacharya et al., 2012)."

Mar 1, 2019

By M. Royle, A. Bloem, R. Uken

Rock mass damage induced by mining increases the fracture frequency and joint aperture width in the pit walls and rock mass behind open pit mine slopes. The depth and intensity of this mechanical damage relative to the pre-mining state is not well understood and yet is a major factor in the development of slope stability models and operational guidelines. The induced damage can be partitioned into domains or zones. The blast damage zone is essentially a ‘free flow’ rock mass volume, which transitions quite rapidly into the excavation damage zone, which extends beyond that. In both zones, transient high in situ water pressures are often linked to unstable slope conditions. Whereas rock damage can enhance passive depressurisation in the rock mass, high infiltration rates on the other hand, as one could expect during rainstorm events, will decrease slope stability within the dilated pit rock mass, especially in the blast damage zone-excavation damage zone, by increasing pore pressures for short periods of time. Ice jacking and freshet are additional factors to consider in (sub) arctic environments and can be exacerbated by unfavorable rock fabric orientation. On a local scale, brittle deformation damage zones, in the form of faults, can contribute to slope instability, or enhanced stability because of slope depressurisation, depending on their location and orientation relative to the pit shape and the water sources. In this study, the shapes of the damage zones and their anticipated impact on infiltration and/or passive depressurisation are considered for different pit morphologies, rock mass conditions, in situ stress, and hydrogeological settings. Some unusual hydrological situations, like mining towards rivers and lakes and the potential effects on pore pressures, are also considered. This investigation has resulted in the development of a method to adjust initial hydraulic conductivity values used to estimate transient pore pressure conditions found in rock masses exposed in different pit morphologies and stress regimes as well as discontinuities’ orientation relative to open faces within the open pit mine. The changes in K values and pore pressures can then be used to determine hydrogeological influence more accurately on future pit slope stability.

Sep 1, 2025

By J. Cilliers, R. Seitz, D. Drinkwater

Mineral processing produces a saleable product from high-cost ore. The Mineral Processing Engineer must constantly improve the separation to create the most value from the ore and reduce the associated costs. Graduate Metallurgists (or Chemical Engineers) have had the university theoretical training required, but often are illprepared to perform their plant roles. The in-work Metcelerate programme was designed specifically to develop the practical skills that Mineral Process Engineers require, by combining three key elements: 1. Knowledge transfer through self-paced, on-line training; 2. Practical skills acquisition through assessed, practical plant exercises; 3. Skills development through online tutorials. A final process improvement project adds significant value to the operation that far exceeds the training cost. Experience from Metcelerate clients has indicated improved staff retention, greater confidence, and pro-active process intervention.

Jan 1, 2023

By C. O’Donova, E. Adam, L. A. Torres-Cruz

High-profile failures of tailings dams illustrate the significant safety challenge they pose. The decant pond of such facilities plays an important role in their mechanical stability. This study investigates the feasibility of using public multispectral data collected by the Sentinel-2 satellite mission to monitor the area of the decant pond. The Sentinel-2 mission has a revisit time of 5 days and the data used herein has a spatial resolution of 10 m/pixel. We considered two water-detection metrics: the normalized difference water index (NDWI) and the near-infrared (NIR) reflectance. Implementation of the method at a South African platinum tailings dam illustrates the capabilities and limitations. Public, sub-metre resolution true-colour imagery served as validation data. There is good agreement between pond area measurements based on Sentinel-2 and the validation imagery. These results suggest the feasibility of using Sentinel-2 data to supplement the monitoring of the decant pond.

Apr 2, 2022

By R. M. Mashishi, T. Malehase, O. J. Okonkwo

The concentrations of selected trace elements (As, Cd, Hg, and Pb in run-of-mine (ROM) coal, discard, and coal product were investigated to assess the efficiency of beneficiation in reducing trace element concentrations and ascertain any implications regarding environmental compliance to regulatory frameworks. Samples were collected from a colliery in Mpumalanga Province twice a month for a period of 24 months. The samples were ashed to approximately 0.21 mm, then digested in a mixture of 70% HNO3 and 40% HF and analysed using inductively coupled plasma-mass spectrometry (ICP-MS). Except for Pb, the mean concentration of all elements decreased from the ROM stage to the coal product stage. The order in which trace elements occurred from the highest to lowest throughout the production chain was Pb>As>Hg>Cd. With the exception of Cd, the mean trace element concentrations in the discard were above the total concentration threshold (TCT) set for landfill disposal. The As, Hg, and Cd concentrations in the product were well below the thresholds for all land uses. However, Pb concentrations in the product coal were above legal limits, which is of concern with regard to environmental compliance and the performance and marketability of the product.

Dec 13, 2023

By F. T. Cawood, M. N. M. Cudjoe

The ability to conduct real-time material tracking in mines has been a long-standing challenge. Technological innovations such as radio frequency identification technology (RFID) have over the years contributed to the effective tracking of material flow and reporting of metal content. This paper outlines the laboratory procedures and results from testing the suitability of microdot technology as a viable technique for real-time material tracking in mining. The paper clarifies the reasons for conducting the test and presents the material safety data sheet (MSDS) from a South African and Canadian perspective. Microdots from three aerosol systems were immersed in water, heated to 100°C, and crushed into coarse and fine material. These tests were used to ascertain if the technology could withstand mining conditions. A strength, weakness, opportunity, and threat (SWOT) analysis was used to evaluate and compare microdot technology with RFID. It was shown that microdot technology has some potential to track ore parcels because data integrity was retained after exposure to post-blast mining conditions. However, more improvement is required to digitally detect microdots before the technology can be implemented at scale in the mining industry.

Apr 2, 2022

By Y. Fan, D. H. Zhang, J. Y. Xu

The hydrogeological conditions in the Chambishi mine area in Zambia. were investigated. Chambishi is a very wet mine and groundwater discharge costs are high. The research goal was to identify methods to reduce the discharge costs without greatly affecting the mining process. Hydrogeological data was obtained from measurements in drill-holes and from drill cores. The differences in structural deformation in different areas determine whether a layer of rock is an aquifer. In the mine region, the Lower Roan Group ore shale and quartz-sandstone unconformably lie on the basal schist and granite aquifuge. The Upper Roan Group dolomite is continuously distributed over a large area around the orebody. This dolomite is the main target of groundwater control efforts, and its water yield is also influenced by the deformation intensity. Based on the observations, backfilling was gradually adopted to appropriately safeguard the integrity of the aquifuge above the orebody. The overlapping relationship between the aquifer and aquifuge has been utilized to increase mine drainage efficiency. This measure has not only greatly reduced the costs of mine drainage, but also improced protection of the groundwater environment. The old drill-holes that were not sealed after exploration drilling were grouted. Further, possible water-conducting fracture zones were investigated. Cover drilling towards the suspected zone was conducted to prevent the high-pressure groundwater from shallower aquifers from entering stopes in deep areas of the mine.

Jun 10, 2024

By S. Khan, M. Auret

Due to the modernisation of mines, traditional training methods may be supplemented to support the upskilling of supervisors in mines. A project was initiated by the SAMERDI SATCAP programme to demonstrate the “art of possibility” through a modern training methodology. Two exemplar digital supervisory leadership development modules for underground gold and platinum-group metal conventional and modernising mines, were developed for potential uptake by the mining industry. These exemplar modules were exhibited on a digital platform, towards leading and driving mining modernisation. The research adopted a mixed method approach that included a literature review, a review of an existing supervisory leadership development programme, data gathering, a pilot study, and stakeholder validation workshops. The research supported the development of exemplar digitised modules. The two digitised modules were showcased to the industry for potential adoption. Training slides, a facilitator guide, and a training video were developed for ease of use by industry. The training modules are generic and not specific to a particular mine. They may be used by multi-commodity mines, including gold and platinum-group metals, as ‘stand-alone’ modules. They are customisable, through consultation with relevant service providers for specific working environments. The findings indicated that both the traditional classroom training and the new digitised online learning solution offer advantages for supervisory leadership development. Digital learning is not a new concept for supervisors at mines and modern training methods are well-supported by supervisors in the industry. A ‘modernised’ training solution may consider a ‘blended’ learning approach that combines traditional training with digital methods.

Jun 27, 2025

By K. Naidoo, M. Pelser, J. Hagemann, K. C. Sole

The copper tankhouse at Rustenburg Base Metals Refinery is an essential component of the Anglo American Platinum value chain. The tankhouse uses starter-sheet technology that was adopted in the 1980s, so dependence on manually intensive labour and overall operational excellence has a significant impact on process performance. An efficient, stable, and sustainable electrowinning process contributes to minimising energy consumption and reducing operational costs, and enables improved product quality and increased throughput. Historic performance of this tankhouse has often been suboptimum over prolonged periods. An in-depth operational review of performance from 2018–2024 was carried out to understand challenges, risks, and high-impact factors that contribute to poor performance. Implementation of adherence to fundamental operational basics identified from global best practice, such as the frequency and quality of cell cleaning and maintenance, preventing backlogged harvesting or maintenance, preserving cell-top furniture conditions and integrity of electrodes, preventing short circuits and poor current distribution, and maintaining a high level of operational discipline, has since contributed to an era of exceptional performance. Root-cause analysis fault trees pertaining to poor current efficiency and high scrap rate are summarised. Current efficiency has significantly improved since 2021, now consistently exceeding 88%. The copper scrap rate, previously believed to be limited to a minimum of 4%, achieved a historic monthly low record of 2.06% in 2023. Chemical and physical quality has considerably improved, and cathodes exhibit minimal morphological defects.

Jun 27, 2025

By D. Sethuram, P. G. Koppad, S. Iyengar, R. Shobha

TiB2 and CeO2 particle-reinforced Al6061 hybrid composites were manufactured using stir casting and hot rolling techniques. The base alloy and composites were hot-rolled at 500ºC and a 50% reduction was achieved through 12 passes. The effect of varying TiB2 and CeO2 particle additions on the microstructure and mechanical properties of the Al6061 matrix was studied. Scanning electron microscopy showed uniform dispersion of both the reinforcements, with good interfacial bonding. Microhardness and tensile properties like yield and tensile strength were found to be higher for hybrid composite with 2.5% TiB2 and 2.5% CeO2 compared to Al6061 alloy and other hybrid composites. The increased tensile strength is attributed to good dispersion and interfacial bonding between the particles and Al6061 matrix. Fracture analysis using a scanning electron microscope revealed ductile fracture for the Al6061 alloy and mixed characteristics of ductile-brittle fracture for hybrid composites

Oct 1, 2021

By S. J. van Wyk, A. S. H. Haagner, A. Abraha

Opencast coal mining is responsible for the greatest area of land disturbance across all of the commodity types in South Africa. Many thousands of hectares have been rehabilitated to date and, although rehabilitation performance is not always measured or reported, a significant database, spanning 24 years, has now been analysed to identify the main shortcomings holding back rehabilitation sustainability across the industry. Data from 48 different collieries with rehabilitation performance scores measured from 2000-2024 were analysed. A standardised assessment framework was implemented at all 48 collieries, focusing on aspects of land capability, soil fertility, landscape form and drainage, vegetation species composition and basal cover, implementation of maintenance programmes, and prevalence of invasive alien plants. The findings show that, although invasive species management, plant species composition, and plant basal cover are often adequate, the implementation of aftercare and maintenance programmes (influencing soil fertility) and deficiencies in overall landform design and drainage systems are most significant in preventing overall rehabilitation progression and self-sustainability. Integrating these during design and rehabilitation execution, followed by intensive maintenance (especially in the first five years post-topsoiling and seeding) will be key for the overall industry performance to improve to acceptable levels. The database is biased towards collieries that actually do undertake rehabilitation and that do measure it, hence the actual industry performance is likely worse than what is presented. Due to the substantial hectarages involved and the main post-mining land uses being grazing and crop production, the industry cannot afford to keep perpetuating deficiencies in achieving the foundational aspects of rehabilitation that would pave the way for sustained economic future use.

Apr 25, 2025