Search Documents

By Keith A. Heasley, Frank E. Chase, Christopher Mark

Deep cover retreat mining (overburden in excess of 750 ft) is an important emerging issue which will intensify in the future as the more easily mined shallow seam reserves are depleted. Analysis of Mine Safety and Health Administration (MSHA) statistics indicates that deep cover pillar recovery accounts for a disproportionate share of the underground coal mine roof/rib fall fatalities and injuries. Past research has shown that previously recommended Analysis of Retreat Mining Pillar Stability (ARMPS) stability factors (SF’s) may be excessive for deep cover pillar design. The objectives of this study were to evaluate the various methods and strategies by which panels, production pillars and barrier pillars are developed and extracted under deep cover, and to develop appropriate design guidelines. In the course of the research, 29 mines in 7 states were investigated to collect panel design case histories. At each mine site, underground geotechnical data were collected on the pillar line in order to document roof rock, coalbed and floor conditions. The analyses indicated that squeezes were the most likely failure mode where the depth was less than 1,250 ft, but bumps predominated in the deeper cover cases. Immediate roof rock quality, the ARMPS SF’s, and barrier pillar stability factors were all found to be important parameters in determining the outcomes of the case histories. Design guidelines, including suggestions for barrier pillars to isolate active panels from nearby gobs in bump prone ground, are also proposed.

By A. U. Miller

Since coal -mining records have been kept , reports of all mining States show that each year the lives of many workers have been sacrificed in the production of coal , and Illinois has contributed its share , Illinois reports for the 50 years 1882 to 1932 , inclusive , show that 6,673 men were killed -- 6,121 underground , 340 in the shaft , and 212 on the surface . Of the fatalities underground , 3,116 were caused by falls of roof or sides , 1,111 by haulage , 630 by explosives , 577 by gas explosions , 139 by electricity, and 548 by other causes ; 166 of the shaft fatalities were caused by falling down the shaft , 143 by the cage , and 31 by other causes ; 108 of the surface fatalities were caused by railroad cars , 46 by machinery , and 58 by other causes . Most of those engaged in mining are still of the opinion that it is an extremely hazardous occupation and that it is practically impossible to operate without accidents ; however , students of safety in mining now believe that with the proper attention to accident prevention mining may be conducted with little , if any , greater accident rate than that of other supposedly hazardous industries . There is no mystery connected with accidents in mining ; reports show that the majority are due to two main causes , falls of roof and sides and haulage . Mining companies in Illinois , as well as in other States , have proved in the past few years that the hazards of mining , like those of other industries , can be controlled to a large extent and the mines operated with few if any accidents , provided a great enough effort is made by employer and worker . Although the past accident rate of Illinois may compare favorably with that of other mining States it is higher than it should be ; the fact that 6,673 men (an average of 133.46 per year) were killed in and around the mines of the State between 1882- and 1932 indicates that accident prevention should receive more consideration in the future than in the past .

Nov 1, 1934

By Fredrick L. Johnson

In 1987, the U.S. Bureau of Mines began a study of the 4.0 million acre Toiyabe National Forest located in eastern California and western Nevada. This report is a compilation of published, company, and field data for part of the Paradise Range, Nevada. The information is intended to aid the U.S. Forest Service in their long range management of minerals and augment the USBM data base. The Paradise Range study area, located 60 air mi northwest of Tonopah, NV, encompasses about 100,000 acres of which approximately 71,000 are administered by the USFS. The area is in the Basin and Range Province and consists of an east tilted block of sedimentary, metamorphic, and volcanic rocks which have been intruded by granitic rocks. Three major mining districts, the Ellsworth, Gabbs, and Fairplay are in, or extend into the study area. The earliest recorded mining activity occurred in the Ellsworth district in the early 1860's. Commodities produced from the study area include gold, silver, copper, lead, zinc, mercury, tungsten, iron ore, magnesite, and brucite. The Phelps Stokes Iron mine has produced about 1.1 million tons of iron ore, the Baxter-Hancock mine has produced over 10,000 stu WO3, and the Gabbs Brucite-Magnesite mine has produced millions of tons of brucite and magnesite. Numerous other mines have produced, but quantities are relatively small. According to company information the Gabbs mine, currently producing, has brucite-magnesite reserves that will last at least 50 years at current mining rates. One hundred thirty one million tons of identified copper-molybdenum resources exist at the B.C. Springs prospect according to company information, but molybdic oxide (Mo03) prices would need to double or triple from the current $3.00-3.10 per lb before mining of the deposit would be economical. Most company exploration activity in the study area is now focussed on precious metals. Active, or recently active mining claims appear to cover more than one-half of the 100,000 acres studied.

Jan 1, 1991

By D. I. Bleiwas

The Bureau of Mines determined demonstrated tin resources and costs associated with tin production in order to evaluate the potential for tin production from 18 market economy countries (MEC's). Data were collected from tin producers, in most cases during on-site visits. The analyses evaluated the relative economic and resource position of 146 mines, deposits, or regions in January 1984 dollars. The demonstrated resource of recoverable tin within the nations studied is approximately 2.8 million metric tons (mt). Of this total, over 73 pct is recoverable from the Southeast Asian countries of Malaysia, Thailand, and Indonesia, which in 1983 accounted for almost 60 pct of the world's tin production. Brazil has joined the Southeast Asian countries as a major low-cost, high-volume supplier of tin and is likely to continue to expand its production. Given the 1984 market structure, over 60 pct of the tin in demonstrated resources was economically recoverable. Historically, the International Tin Council (ITC) has helped maintain relatively stable tin prices through a buffer stock and sales quotas. In late 1985, exhaustion of buffer stock funds led to suspension of tin trading on the world's major tin metal exchanges.

Jan 1, 1986

By Wilbur A. Haley

One of the purposes of the investigation was to determine and report on how coal augers are used to mine bituminous coal that is near outcrops and may not be mined otherwise by any other present-day method. Such increased overall recovery results in the conservation of coal resources. Other reasons for the investigation were to determine and report the production rates of such operations and the types of equipment used. Auger mining of coal as a means of coal recovery supplementary to strip mining has been introduced and developed since World War II. This type of coal mining has grown rapidly, and bituminous-coal production by auger mining has been estimated at 6,000,000 tons in 1955. Mines were selected for study to give reasonably representative information on auger mining in different types and thicknesses of coal beds in different geographic areas and on different types and sizes of equipment operated under various conditions. This report is based on field studies of 8 auger-miming operations in Pennsylvania, West Virginia, and Ohio and in 5 different coal beds. Operations were observed in active strip mines, in strip mines reopened for auger mining, and along benched coal-bed outcrops. At the time of this study, no augers were reported to be operating in underground mines. The diameters of holes drilled ranged from 26 to 52 inches, and the lengths of holes ranged up to 208 feet. At some operations auger holes often penetrated abandoned underground mine workings.

Jan 1, 1957

Objective To develop safety training tools for mine safety and health trainers that can be used for both new-miner training and annual refresher training. Background For the past 3 years, NIOSH has been developing training materials for mine safety trainers in response to gaps identified during stakeholder meetings. Most materials have been directed to the hazards of underground mines, but the recent passage of Part 46 of CFR 30 required new-miner and annual refresher training in aggregate operations. One result was the identification of another audience needing basic information about safety in mining. Trainers characterized trainees in this segment of the industry primarily as young males, many of whom had little work experience. Approach Training specialists from the Arizona State Mine Inspector’s Office approached NIOSH researchers early in2002 about the possibility of a collaborative project to develop safety training materials for new trainees in aggregate operations. A preliminary search of MSHA accident statistics identified over a dozen common hazards that could be targeted in a training video. A storyline was developed for review by safety specialists in the aggregate industry, and a script was written to cover the selected hazards. Although the target audience was primarily new hires, the finished video was also to be relevant to more experienced workers.

Jan 1, 2003

By Jack Mantel

The goal of this 42-month contract was to increase safety in low-seam underground coal mines through development and in-mine evaluation of a temporary roof support system for roof drills and floor-riding operator compartments for a loader and shuttle car. The program was performed in three phases. During Phase I, state-of-the-art canopy technology was investigated, and preliminary design and mock-up evaluations were performed for temporary roof supports for single-and dual-boom bolters and for transverse-mounted floor-riding canopies for a shuttle car and coal loading machine. The shuttle car and loader canopies were approved for further development, and the design, fabrication, testing, and certification were completed in Phase II. In Phase III, the Bureau of Mines furnished an FMC 6L shuttle car fur use in the evaluation of the canopy for 45 shifts. The shuttle car canopy was evaluated at Virginia Crews Coal Company in West Virginia. Efforts to secure an evaluation site for the loader canopy were unsuccessful. The loader canopy was shipped to Bruceton for possible future evaluation.

Jan 1, 1985

By C. W. Davis, M. W. Von Bernewitz, S. C. Lind

During the past few years our possible domestic resources of platinum have attracted much attention . On account of the extensive use of platinum during the World War , and the practical elimination of the Russian supply , the price of this metal rose to new high levels , as shown in Table 1 ; and though it since receded to some extent , the price is now nearly six times that of gold .

Jun 1, 1923

By Robert B. Fulton

Summary of data and estimates for 52 fluorspar properties in the following 13 foreign countries: Mexico Thailand China (PRC) Morocco Tunisia Italy Spain South Africa France United Kingdom Kenya Namibia Federal Republic of Germany Data includes deposit type, resource tonnage and grades, mining and beneficiation methods, annual production, fluorspar products and by-products, manpower requirements, capital and operating cost estimates. For operating properties, engineering and cost data have been developed for present and anticipated levels of production. Hypothetical operations have been assumed for undeveloped deposits.

Jan 1, 1984

These inspection standards have been prepared for use in the Federal inspection of bituminous and lignite mines. They are a revision of "Tentative Coal-Mine Inspection Standards," published as Bureau of Mines Information Circular 7204 in February 1942 and employed a guide for Federal inspections. Numerous changes have been made in the original standards owing in part to recognition of shortages of some types of safety equipment due to the war, in part because of need of additional standards to cover certain mine conditions' arid' practices, and in part to conditions not foreseen when the original standards were prepared. About one-fourth of these standards are marked with an asterisk (*) as being of particular importance in preventing accidents in many coal mines; however; failure to carry out the suggestions made in such of the other standards as are applicable may also' lead' to the loss of lives.

Jan 1, 1943

Although the mining industry has achieved record-low fatalities and injuries for each of the last three years, there are still too many miners injured or killed in this nation ís mining operations. Many mining injuries or deaths might have been prevented by using risk assessment to identify and control or eliminate the hazards associated with a task. To focus attention on the importance of conducting risk assessments in keeping mining workplaces safe and healthful, MSHA introduced this initiative on October 12, 2004. This initiative is called SLAM. SLAM is an acronym for Stop, Look, Analyze, and Manage. The steps involved in SLAM are: Stop ñ stop and consider the work involved Look ñ look for and identify the hazards Analyze ñ analyze what needs to be done Manage ñ manage safety by developing and implementing controls Everyone should be aware of the risks of an accident before beginning a task. It may not always be obvious that performing a seemingly routine task could result in an accident. That is why conducting a risk assessment is so important. Itís important to remember that over time a mining workplace seldom remains unchanged. Risks must be assessed whenever procedures or processes change, whenever new tasks are started, or non-routine tasks are performed.

Jan 1, 2005

By D. H. Yardley

A major purpose of this contract was to evaluate a variety of dust suppressants to determine their effectiveness in mitigating dust from taconite tailings. During the course of the investigation tailings from pilot-plant tests of Minnesota copper-nickel ores became available and chemical binders were also tested for dust mitigation effectiveness on this mineralogically different material. Field-test plots were established on taconite tailings and wind tunnel laboratory tests conducted. The laboratory tests consisted of comparing treated and untreated samples at wind velocities of 40 mph using a weight-loss method and direct dust emission measurements. It was shown that the emission of fine dust from taconite tailings, in the range of 4.5 microns to 0.85 microns, could be reduced by 99 percent using certain chemical suppressants. It was also demonstrated that a straight water spray on coarse tailings (3/4" to + 10 mesh) reduced dust emission by 95 percent. Although eight different chemicals were tested, most of the tests were made using Coherex, ammonium lignin sulfonate and sodium silicate. These same dust suppressants were used, singly and in combination on almost 75 field-test plots. The Coherex appears to provide the best results in terms of economics and durability. Wind tunnel tests on treated and untreated Cu-Ni tailings demonstrated that applications of dust suppressants reduced fugitive fine dust by better than 99 percent.

Jan 1, 1980

By B. W. Dunning

This paper describes studies conducted by the Bureau of Mines to achieve its goal of developing methods for increased recovery and utilization of valuable constituents in a wide variety of domestic and industrial wastes, In this particular study, 36 units of obsolete electronic equipment from military aircraft were disassembled into their modular components by hand to determine materials distribution. Further modular disassembly into individual parts was used to identify metal composition. After identifying the metals in some of the more difficult to dismantle modules, similar modules were grouped together, shredded, mechanically separated, and using metal composition data from hand separation, classified along with the hand-separated materials. Although this equipment is normally classified as law-value iron-bearing aluminum, data were obtained that indicated the potential for moderately higher value classification. The electronic units were classified as to precious metals, copper, iron, and aluminum contents, and scrap values were estimated.

Jan 1, 1980

By Russell R. McLellan

As part of an effort to develop new or improved placer mining technology in the Tertiary gold-bearing channel gravel of northern California, the Bureau of Mines conducted investigations at the old Badger Hill placer mine in Nevada County, Calif., to collect data and information regarding drilling and sampling methods and deposit characteristics. Sampling studies involved the collection and processing of 400 tons of large-and small-volume samples from drill holes, underground workings, surface pits, and blasthole rounds. A total of 355 samples averaging 2,296 pounds per sample provided reasonably accurate data for analysis of the gold distribution. These studies indicated that the bulk of the gold is within 40 feet of bedrock in stacked, lenticular zones of cemented gravel that are largely confined to the relatively narrow, meandering course of the deepest portion of the bedrock channel. Drilling studies involved the testing of truck-mounted rotary, buckett and vibratory drills, none of which proved to be a completely versatile tool for sampling quickly and reliably both consolidated and unconsolidated gravel..

Jan 1, 1974

More gold is being produced now than ever before in recorded history. All over the world huge quantities of ore are being mined and processed, thanks to historically high prices for gold and the use of processing techniques demonstrated as cost efficient in the last 20 years. Over the past 10-15 years prices for many other metals have been depressed, and gold has accounted for a significant proportion of worldwide exploration and development expenditures(l)1. The revenues generated from gold mining are providing greater return on investment, more jobs, and more tax revenues to national governments than ever before. Emerging nations are using the gold industry as a springboard for development; developed nations are continuing to fuel their economies with gold industry revenues; and China and countries of the former Soviet Union are using the gold industry to generate foreign exchange, modernize their mining industries, and take the first tentative steps toward private sector participation in their economies.

Jan 1, 1994

By Robert J. Timkp, James D. Noll, Peter Hall, Robert Haney, Linda McWilliams

Diesel particulate matter (D PM) samples from underground metal/nonmetal mines are collected on quartz fiber filters and measured for carbon content using National Institute for Occupational Safety and Health Method 5040. If size-selective samplers are not used to collect D PM in the presence of car-bonaceous ore dust, both the ore dust and D PM will collect on the quartz filters, causing the carbon attributed to D PM to be artificially high. Because the D PM particle size is much smaller than that of mechanically generated mine dust aerosols, it can be separated from the larger mine dust aerosol by a single-stageimpacto1: The SKC D PM cassette is a single-stage impactor designed to collect only D PM aerosols in the presence of carbonaceous mine ore aerosols, which are commonly found in underground nonmetal mines. Howeve1: there is limited data on how efficiently the SKC D PM cassette can collect D PM in the presence of ore dust. In this study we investigated the ability of the SKC D PM cassette to collect D PM while segregating ore dust from the sample. We found that the SKC D PM cassette accurately collected D PM. In the presence of carbon-based ore aerosols having an average concentration of 8 mg/m3, no ore dust was detected on SKC D PM cassette filters. We did discover a problem: the surface areas of the D PM deposition SKC D PM cassettes, manufactured prior to August 2002were inconsistent. To correct this problem, SKC modified the cassette. The new cassette produced, with 99% confidence, a range of D PM deposit areas between 8.05 and 8.28 cm2, a difference of less than 3%.

By GEORGE T. Harley, Walter R. Storms

This paper, which describes mining mothods at International Minerals & Chemical Corp, 'e. potash mine. in. Eddy. County, N. Mex., is one of a sories being prepared by the Mining Branch of the Bureau of Minos. on mining method a and practicos in, various mining districts of the United States. The mine shafts and. surface plant or International Minerals & Chemical Corp. are situated. in. sec.. 12, T. 22 S., R. 29 E., N. M. P. M., about 26-1/2 miles by paved highway east of the city of Carlsbad (figs. 1, 2, and 3). A spur line of the Atchison, Topeka & Santa Fe Railroad connects the mine with the Clovia-Pecos branch of the same road near Loving, a few miles south of Carlsbad. This spur also serves the refinery of United Staics Potash Co. This report gives. the history and describes the geology of the district. Methods of prospecting, exploration, sampling, and estimation of tonnage and values are explained; development and mining methods are discussed in con- siderable detail; transportation, ventilation and drainage are outlined; safety measures are noted; and the wage scale and organization are mentioned.

Jun 1, 1949

By Joel M. Modd, Stephen P. Holt

"INTRODUCTION Nickel is one of the seven metals designated as strategic by the Army and Navy Munitions Board in 1939, when Congress appropriated funds for the investigation of domestic sources of supply of war minerals. The Mertic nickel lode at Punter Bay, Admiralty Island, Alaska, owned by the Admiralty Alaska Gold Mining Co., was investigated as part of this program.During the period 1919 to 1928, the property was examined the following engineers; L. S. Robe, W. E. Dunkic and S.E. Conbest of the Alaska Treadwell Cr., A, F. Buddington of the Federal Geological Survey, and H. C. Boydell. Henry M. Eakin, in the capacity of consulting geologist, examined the deposit in 1928 and later reviewed data resulting; from exploration recommended by him. In 1936, A. Hoogbom, of the Geological Survey of Sweden, made a very brief report on the deposit based upon information furnished by J. S. Pokovich.A comprehensive study by the Geological Survey of the Punter Bay area, including the Mertic lode, was made during the field season of 1937, with brief examinations in 1936 and 1938. 4/Miyaki, representing the Mitsubishi Company, visited the property in 1937 and in the course of his examination took six samples. G. W. Powel examined the deposit in 1937 and took five samples in the Mertie adit.This report describes the results of the Bureau's work and gives information collected from other sources."

Nov 1, 1946

By T. A. Sullivan

The processing of sweated aluminum electronic scrap was investigated to develop methods for recovering the aluminum and concentrating the other metals, including copper, lead, gold, and silver, into a product that can be separated by known methods. Two molten-salt electrorefining processes were developed and tested. The first process utilized a three-layer refining cell with a BaCI2-NaF-AIF3 electrolyte, which operated at 750° to 850° C. The second process used an all-chloride electrolyte of NaCI-KCI-AICI3 at 750° to 800° C, with separate anode and cathode compartments. High-quality aluminum was recovered that averaged 99.8-percent pure in the three-layer cell and 99.6-percent pure in the compartment cell. Over 94 percent of the aluminum was recovered with cathode current efficiencies of approximately 90 percent in both methods. The copper, lead, tin, silver, gold, and other metals were concentrated threefold in an anode product. Separation of lead and part of the tin by liquation from this product seemed feasible. The anode product was smelted to prepare a 96-percent copper bullion that contained 690 ounces of silver and 65 ounces of gold per ton, with 98 percent recovery of these values.

Jan 1, 1972

By Anil Mahyera

This report present the results of a laboratory and field research program aimed at design and development of a torque-thrust controlled bolter with the capability to (1) predict the "quality of anchorage" attained while installing mechanical anchor roofbolts, and (2) improve the uniformity and tension levels achieved among a group of roofbolts. The prediction accuracy of the anchorage quality algorithm ranged from low to moderate because of the complexity and variability of the phenomena involved. The best roof support with mechanical anchor bolts was found to be achieved by simply installing them under ? proper torque-thrust control, and with ? a hardened washer under the bolthead. This procedure resulted in an improvement in uniformity of 3 times, along with an increase in mean tension levels of 75% over conventionally installed roofbolts.

Jan 1, 1983