Search Documents

By David R. Flinn

This Bureau of Mines report describes methods to electrodeposit erosion-resistant titanium diboride coatings from molten alkali metal borate baths at 900° C. These coatings have been shown to be highly resistant to material loss during impingement with high-velocity alumina and silicon carbide powders, and they show promise as protective coatings to reduce metal loss in erosive chemical environments, such as coal gasification systems. The most erosion-resistant coatings were prepared on nickel, Inconel, and molybdenum from an electrolyte containing LiBO2, NaBO2, Na2Ti03, and TiO2. The best coatings were deposited at current densities of [~]20 ma/cm2, using titanium or titanium diboride anodes. Erosion-resistant coatings were shown to exhibit (1) a high degree of crystallographic orientation along the (100) or (110) planes, (2) a chromium impurity level of less than 3 pct, and (3) a uniform, smooth, consolidated surface appearance when viewed under a microscope or by scanning electron microscopy. Optical spectroscopic studies of the molten electrolyte suggest that the lower valent (+3) titanium ion predominates in the baths.

Jan 1, 1979

By R. J. Leary, W. M. Mahan, F. X. Tartaron

A new type of apparatus for prerefining molten blast furnace iron and to reduce the cost of subsequent steelmaking consists of a funnel - shaped device lined with firebrick into which a horizontal stream of molten pig iron is directed tangentially at the top . The rotary motion thus induced causes the stream to flatten itself upon the wall and flow in a spiral path to the outlet ; thus , the device was termed " vortex cone .' Oxygen and other refining agents are impinged upon the flowing metal in the cone where reaction is facilitated by the large metal surface exposed and the turbulent flow pattern . Experiments with water in 1 - foot - diameter funnels provided an idealization of the flow patterns to be expected with molten iron . A brick - lined reactor 3 feet in diameter was built for desiliconizing molten pig iron in lots of 1 to 2 tons . At flow rates of 0.3 to 0.5 ton min - 1 (430 to 720 tons per day ) this apparatus was 64- to 90 - pct effective in desiliconization with oxygen efficiencies of 19 to 41 pct . Detailed experiments to develop basic engineering data are underway , and adaptation of this principle to other reactions and reactants is planned .

Jan 1, 1964

By R. H. Sprute

Underground accumulations of slimes in the Henderson mine are routed to two large collection pits where they are dewatered and consolidated by application of direct current. Densified material is then removed to ore cars by rubber-tired front-end loaders and transported out of the mine. This Bureau of Mines report describes the electrical dewatering installation and compares its efficiency of operation with that predicted from preliminary laboratory studies performed by the Bureau. Direct current from a 150-kw rectifier (applied for 44 hours at 400 amperes and 65 to 70 volts) converted slimes containing 25.3 percent solids to material ranging from 44 to 65 percent solids. Better results can be expected if the ramp and front sections of the pits are treated separately, using higher current density.

Jan 1, 1980

By Phil Patton, Bill M. Stewart, Curtis Clark

Handling materials in underground mines continues to be a major safety problem. To help reduce materials-handling injuries, the National Institute for Occupational Safety and Health (NIOSH) at the Spokane Research Laboratory is developing, modifying, and testing equipment to replace the necessity of doing lifting tasks manually. To reduce single-event lift injuries, equipment having mechanical automatic weight sensing and balancing control was investigated. The Coleman manipulator was selected for testing. Modifications to the Coleman manipulator to make it more suitable for underground mine use included mobilization, self-containment, all-purpose gripper attachment, and support jacks. To reduce or eliminate the need to clean off manually the materials that commonly plug grizzly openings (timbers, wire mesh, roof bolts, and other debris), a track-guided pincher arm device was developed. The TGPA attaches to an impact hammer head, and the pincher arms are controlled by the operator of the hammer. Oversized rock can be broken with the pincher arms in the up position; the arms can then be lowered to grab and remove debris. Sweeping action to remove cohesive fines bridging grizzly openings is also greatly improved. This device is especially useful in recessed grizzlies. An industrial gun was tested to evaluate its effectiveness in breaking oversized rock. Boulders up to 76 cm in diameter were successfully broken to minus-33 cm. Although methods to control fly rock need to be developed, an industrial gun may be a safe and inexpensive alternative to breaking oversized rock in certain underground mining situations.

By B. W. Gandrud

In 1927 Coghill5 showed that there is considerable liberation of the iron oxide mineral from gangue when the Alabama red iron ores are ground to a size suitable for classification and tabling, but that there is not sufficient to make possible a high extraction and a high grade of concentrate. Coghill states: High extraction and high grade of concentrate cannot be obtained without grinding to a size comparable with flotation or cyanide practice. If grade of concentrate be sacrificed the grinding need not be so severe.

Jan 1, 1934

By Richard H. Spencer

Since the passage of the Coal Mine Health and Safety Act of 1969, the Bureau of Mines has made many advances in mine communications. These efforts have resulted in the following developments and demonstrations: Surface-to-surface electromagnetic transmission of baseband voice signals through overburdens as deep as 600 feet. This transmission was achieved with equipment from the Interim Mine Rescue and Survival System Program, and demonstrated that baseband voice communications could be obtained through these overburdens in the absence of mine-generated noise; that is, when the mine power system was shut off, However, during mine operational conditions, the mine-generated noise proved to be so large that effective baseband voice communications to the desired depths could not be effected.

Jan 1, 1975

By A. V. Hooker, E. J. Coggeshall

"The Bureau of Mines for some time advocated the firing of all blasts in coal mines as single shots, and this method of firing is the general practice in American bituminous-coal mines. All single shots can be fired with permissible single-shot units so designed that they will not ignite mixtures of methane and air.If several shots in a face are fired singly it is necessary to return the face after each shot. In some mines having steeply pitching coal seams, this may be dangerous or even impossible, under these conditions shots are usually fired simultaneously.Several shots cannot be fixed simultaneously with permissible single-shot blasting units, and safe types of multiple shots blasters are not readily available. This means that the firing of multiple shots in gassy mines is usually accompanied by the possibility of gas ignition as the blast occurs.Tests have been made at the Pittsburgh Experiment Station to determine the possibility of developing safe types of multiple-shot units suitable for such use, or of applying other type safely in gassy sections of mines where firing shots singly is impracticable.The tests may be divided into the following four groups:1. Tests to demonstrate hazard in the use of existing types of multiple-shot units of the portable generator type.2. Tests to show the electrical characteristics of multiple-shot generator units relative to the possibility of preventing igniting sparks and of modifying the design and application of such units in furthering safety."

Mar 1, 1935

By Richard L. Rains

The Bureau of Mines conducted a mineral investigation of the 29,000-acre Dixie Summit area near Elk City, Idaho, during the summer of 1989. At the Petsite mine a marginally economic, identified resource of 4.9 million tons with an average grade of 0.023 ounces gold per ton was delineated. Possible resources of gold, along with silver, copper, lead, and zinc, occur in at least eight other lode deposits. Placer gold may be recoverable by recreational-sized suction dredges in some stream drainages, Five lode mines in the study area have produced over 5,516 ounces of gold (placer gold production was not recorded), 4,757 troy ounces of sliver, 36,746 pounds of lead, and 3,800 pounds of copper. Current mining claims in or adjacent to the study area total 460 lode and 70 placer claims. There are two patented lode claims within the Dixie Summit study area.

Jan 1, 1991

By P. H. Floyd

Laboratory test work has shown that the Germania ferberite-scheelite ore can be concentrated to an acceptable grade. A ferberite concentrate assaying 66.9 percent tungstic oxide was made, with a recovery of 75.4 percent. A second concentrate of ferberite and scheelite was made assaying 54.2 percent tungstic oxide. Final beneficiation of combined rougher gravity concentrates was accomplished by roasting, magnetic separation, sulfide flotation, and retabling, to give a final ferberite-scheelite concentrate of 66.2 percent tungstic oxide, with a 91.1-percent recovery. INTRODUCTION This presentation covers the results of laboratory beneficiation tests conducted on tungsten ore from the Germania Consolidated Mines, Inc., by the Bureau of Mines Mineral Dressing Section, Northwest Electrodevelopment Laboratory, Albany, Oreg. This mining property is near Fruitland, on the southern edge of the Spokane Indian Reservation, Stevens County, Wash. The Germania district produced tungsten concentrates before and after World War I; interest is being renewed in the district because of the metal shortage.

Jan 1, 1954

By Wesley A. Grosh

The Vest nickel prospect, in Floyd County, Va., was discovered about 25 years ago. Limited exploration of the deposit had indicated some appreciable nickel mineralization in the sulfide ore. The property was examined on March 9, 1943, by an engineer of the Bureau of Mines in company with C. W. Vest, owner of the property. A limited exploration program was recommended. Two holes totaling 320 feet were diamond-drilled in January 1944. Drilling indicated the sulfides are sparsely disseminated. The only nickel values of interest were at the old prospect shaft.

Jan 1, 1949

By C. R. Hopkins

"The petroleum refiners of the United States made rapid strides in fuel economy in 1928, when the calculated number of B. t. u. required to refine a barrel of crude petroleum was 637,000 as compared with 698,000 in 1927, a decline of 9 per cent. The major portion of this indicated increase in fuel efficiency was undoubtedly due to the gain in use of the pipe-still and the continuous process of refining as contrasted with the old batch method of distillation.,Almost without exception the new refineries are equipped with one or more pipe-stills, and many of the older plants are changing over to this type of equipment. The refineries of the Appalachian area are among the oldest and most conservative of the country, yet a number of them dismantled their old shell and cheese-box stills and installed pipe-stills in 1928.The more extensive use of the pipe-still was not the only way in which the refiners lowered their fuel requirements in 1928. The use of heat-exchangers, in which the heat from hot vapors to be condensed is used to heat the incoming cold oil, also increased in 1928, and in addition the refiners have kept abreast of the times in saving fuel through better insulation and improved burners.For the year 1928 the refiners burned as fuel the following: 46,400,000 barrels of-fuel oil; 3.362,000 short tons of coal; 114,950,000,000 cubic feet of natural gas; 77,313, 000,000 cubic feet of refinery or still gases; and 470,000 short tons of coke, in addition to a little electricity. This fuel was calculated to have produced a grand total of 582,156 billions of B. t. u., as compared with 578,784 billions B. t. u. in 1927.The total of 46,400,000 barrels of fuel oil burned represents an increase over 1927 of about 5,000,000 barrels, which made it about equal to the 1926 figure. Practically all of the refinery districts used more oil as fuel in 1928. The most important increase - over 2,000,000 barrels - occurred in the East Coast district, where greatly expanded throughput of foreign crude was instrumental in increasing fuel-oil production.The use of coal for fuel at refineries again registered a material decline, the total for 1928 of 3,362,000 short tons being 33 per cent below that of the previous year. The outstanding decrease in the use of coal in 1928 occurred in the East Coast district, where coal was probably replaced by oil. The use of coal for fuel at refineries in the States of Ohio, Pennsylvania, and West Virginia declined materially in 1928; the substitute used in the majority of cases was oil burned in pipe-stills."

Nov 1, 1929

By Doris M. Hyde

Mineral industry activity in many of the smaller Caribbean Island countries has remained minimal. For this reason, specific references to Bermuda, Guadeloupe, Martinique, and the Netherlands Antilles have been removed from textual and trade table presentations. Any significant future developments will be reported as they occur. Readers are referred to earlier Minerals Yearbook editions for previous information. Table 1 production statistics have been modified in some instances. References to certain nonmetal commodities were eliminated because information has often been unreliable. Their inclusion in table 1 was not considered important to either an overview of the area or to compatibility with volume I of the Minerals Yearbook.

Jan 1, 1984

By L. B. Pankratz

Present-day interest in the rare-earth elements and their compounds, for both metallurgical and ceramic uses, makes it highly desirable to accumulate basic thermodynamic data that can be applied to theoretical considerations of the processing of these substances. Such data still are seriously lacking. This Bureau of Mines paper reports the results of high-temperature heat content measurements of the sesquioxides of four rare-earth elements--europium, gadolinium, neodymium, and samarium--and of the closely related element, yttrium. The temperature ranges covered by the measurements are as follows: Monoclinic Eu2O3, 298°-1,802° K. Cubic Eu203, 298°-1,350° K. Monoclinic Gd203, 298-1,802° K. Cubic Gd203, 298°-1,550° K. Hexagonal Nd203, 298°-1,795° K. Monoclinic Sm203 298°-1,798° K. Cubic Sm203, 298°-1,149° K. Cubic Y203, 298°-1,799° K.

Jan 1, 1962

A knowledge of the mechanics of wave propagation through the earth is essential if reliable communication systems are to be designed for coal mine environments. To obtain a reliable basis from which accurate propagation predictions could be drawn, a series of theoretical studies have been prepared for the US Bureau of Mines by Mr. Ramsay Decker of Spectra Associates, Inc. through a subcontract with Collins Radio Group. These reports formulate the analytical techniques from which we may derive frequencies and antenna configurations that yield the optimum signal-to-noise ratios over the greatest distances in mine environments. The reports of sections 2 and 4 deal with analytical techniques for determining the signal-to- noise ratio within a mine environment for loop-to-loop and line source-to-loop antenna con- figurations. The analytical results of these reports were then implemented into computer programs to obtain predictions concerning through-the-earth signal propagation. These preliminary predictions are based on noise data compiled by Bensema, Maxwell and Stone, and WVU prior to the extensive research conducted by the National Bureau of Standards (NBS). These initial measurements indicated a 20- to 30-dB lower noise level than that measured recently by NBS. The recent NBS data is that used by Collins in the final predictions. The following outline indicates the order and subject matter treated in the subsequent sections: Section 2 - Signal-to-Noise Analysis for Loop-to-Loop Mine Communications Section 3 - The Horizontal Electric Dipole Section 4 - Signal-to-Noise Analysis for Down-Link Line Source Mine Communications Section 5 - LF Communication Section 6 - The Application of Recent NBS Noise Data to Mine Communications Section 7 - Analysis of Mine Communication Propagation Programs

Nov 15, 1974

By Paris V. Brough

This paper, which describes the practice of milling custom ore, in addition to that produced under company and lease operations in the Tom Reed mines, is one of a series 'being prepared by the Bureau of Mines. ACKNOWLEDGMENT Acknowledgment is made to W. B. Phelps, managing director, and Jack Zwinge, superintendent, far permission to publish, a-ad to G. E. Jarpe, the present mill superintendent, for his assistance in preparing the paper. LOCATION The mill is in Oatman, adjacent to the Benjamin Harrison shaft of the Tom Reed Gold Mines Co., in the foothills on the western slope of the Black Mountains, western Mohave County. The railroad shipping point is Kingman, Ariz., 25 miles northeast of Oatman. Paved highway U. S. 66 passes by the mill. The altitude is approximately 2,700 feet.

Jan 1, 1937

1. PURPOSE The Temporary Face Support System (TFSS) consisting of beams, posts and carrying-emplacing equipment was developed to provide temporary supports between the working face and the permanent roof supports. 2. GENERAL DESCRIPTION The system consists of: ? A Beam And Post Carrier And Deployer (BAPCAD), a self-propelled machine that carries as well as emplaces the beam-and-post sets. ? Lightweight mechanically self-deploying posts designed to safely support a load of 10,000 pounds each. ? Lightweight constant strength beams (bars) capable of sustaining an approximate equally distributed load of 8500 pounds. Note. All referenced figures and drawings are found at the back of this manual.

Jan 1, 1980

By Jalna R. Zatko

Coal-clay waste slurries were dewatered in laboratory-and small-scale continuous tests by the Bureau of Mines using polyethylene oxide (PEO) as a flocculant. Dewatering from a nominal 7-wt-pct solids to over 50-wt-pct solids was accomplished using 0.5 lb of PEO per ton of feed in small-scale continuous tests. Parameters such as pH, initial solids content, and PEO concentrations were investigated. Water recovered from dewatering was reused as dilutant for PEO solutions.

Jan 1, 1982

By Arthur L. Murray

"Oil-shale camps are peculiarly favored, in that before they are established it can be ascertained with a,of certainty, that the life of the project is not limited. Unlike camps at metal mines, where the metal content of a given area is frequently an unknown quantity until after years of development, oil-shale camps should, from the outset, be planned and built as permanent types of camps. Where this procedure is followed camps will be established which better serve the needs of the industry and the cost of their general care and upkeep will be less.Selection of camp or townsite.The site of the camp or town, whether on company property or not, should be selected with care. It should be separate if possible from the location of the plants of the company so as to be free from noise and fumes and so as to provide a change of environment for employees in going from their work to their homes.The principal features governing the site to be selected are as follows:Drainage. The general contour of the surrounding country should be such that drainage is away from the site. The camp or town should, if practical, be situated on higher ground than that in its immediate vicinity.Soil. The nature of the soil on which the camp or town is located may bear a decided relation to health. A porous, well under drained top soil of at least four feet in depth insures dryness and facilities the placing of foundations and the laying of water mains and sewer pipes. Such a soil also is an advantage in growing trees, shrubs and grass plots, which are a decided adjunct to making the community attractive."

Jun 1, 1921

By William B. Harper

Domestic sales of carbon black sustained the upward movement for the 4th consecutive year, reflecting the increased sales of motor vehicles during the same period. Sales of carbon black in the domestic market topped 2 billion pounds for the first time during 1965 and have more than doubled the output of 20 years earlier. By far the largest user of carbon black is the rubber industry. That use accounted for more than 94 percent of the carbon black consumption with the bulk of it being used in tire casings and tubes. Thus demand for carbon black is naturally sensitive to trends in the sales of passenger cars and other motor vehicles, Manufacturers of inks, paints, plastics, paper chemicals, and food are also important users of carbon black.

Jan 1, 1967

By Corwin L. Cooper

This paper, describing; the milling and cyanidation methods and costs at the Yellow Aster gold mine, is one of a series of papers being prepared by the Bureau of Mines on bold milling practices in the United States. Acknowledgments Acknowledgment is made to the executives of the Anglo American Mining Corporation, Ltd., for permission to publish this article, and to A. W. Frolli, manager, and other members of the company staff, for assistance` in preparing the, paper.

Jan 1, 1936