Search Documents

By R D. Fleming

A single-cylinder research engine was operated on pure hydrocarbons and simple (two-component) mixtures of pure hydrocarbons to study the effect of fuel composition on exhaust emissions from a spark-ignition engine. Used as fuels were three pure hydrocarbons that represented the primary hydrocarbon types present in commercial motor fuels: A paraffin (2,2,4-trimethylpentane), an olefin (2,4,4-trimethylpentene-2), and an aromatic (meta-xylene). The engine was operated at the same equivalence ratio for all of the fuels used in the experiment. Exhaust gas samples were collected and quantitatively analyzed for carbon monoxide, carbon dioxide, hydrogen, nitrogen oxides, aldehydes, and hydrocarbons. Exhaust hydrocarbons were separated and quantitatively measured with a chromatographic system employing a flame-ionization detector. Unknown hydrocarbons and oxygenated materials in the exhaust were identified with a Time-of-Flight mass spectrometer coupled to a chromatographic system. The results of the exhaust gas analyses showed that ethylbenzene, l-methyl-3-ethylbenzene, and l-methyl-3-vinylbenzene were more abundant in the exhausts from either 2,2,4-trimethylpentane--m-xylene or 2,4,4-trimethylpentene-2--m-xylene fuel mixtures than in exhaust produced from m-xylene. Also, the pure 2,4,4-trimethylpentene-2 fuel produced smaller amounts of C2 to C7 olefins in the exhaust than that produced by the pure 2,2,4-trimethylpentane fuel. The exhaust from pure m-xylene fuel contained aromatic hydrocarbons of higher molecular weight than the parent fuel. The amount of total hydrocarbon (moles of exhaust hydrocarbon per mole of fuel used) in the exhaust from the three pure fuels decreased in the following order: 2,2,4-trimethylpentane > 2,4,4-trimethylpentene-2 > m-xylene. The hydrocarbon mole-fractions of unreacted fuel in the exhausts produced from each of the pure fuels were 0.20 for 2,2,4-trimethylpentane, 0.13 for 2,4,4-trimethylpentene-2, and 0.66 for m-xylene.

Jan 1, 1970

By C. A. Komar

Laboratory-scale hydraulic fracture tests were conducted by the Bureau of Mines on directionally oriented sandstone material, along with measurements of directional rock properties such as tensile strength, permeability, ultrasonic velocity, and dynamic elastic constants. In these tests, fracture orientation was determined as a function of various combinations of stress, rock saturation, rate of borehole pressurization, and direction of minimum tensile strength relative to minimum horizontal compressive stress. The objective of the experiment was to investigate whether horizontal stresses always controlled the orientation of induced vertical hydraulic fractures, or if under conditions of small differences in stress and/or slow borehole pressurization rates, the induced fracture direction was influenced by directional properties of the rock matrix. This study shows that the expected influence of horizontal earth stress on the orientation of an induced hydraulic fracture becomes negligible when¬ever the magnitude of the difference between the compressive stresses is 200 psi or less. When this occurs, fracture orientation is controlled by the directional properties of the rock--primarily permeability and tensile strength.

Jan 1, 1973

By Zsuzsanna Zborovszky

Experimental study directed toward gaining improved understanding of the exact mechanisms causing ignition in the PTB breakflash. Investigation and comparison of tungsten and copper wires as to their ability to cause hot wire ignition. Evaluation of the importance of discharge duration in the ignition process. Study of the parameters influencing the duration of a discharge (minimum discharge voltage, purity of electrode materials, purity and properties of the gaseous atmosphere contaminations, deposits on the electrode surface).

Jan 1, 1976

By John H. Soulé

"INTRODUCTION Spodumene and lepidolite were shipped from the Harding pegmatite deposit, Taos County, N. Mex., in the period from 1930 to 1930. Tantalum minerals were noted as early as 1924 and described in 1931 3/ but no tantalum ore was shipped until 1942. The deposit was mapped and studied by geologists of the Federal Geological Survey and engineers of the Bureau of Mines late in 1942 and early in 1943, and a Bureau of Minus exploratory project was carried out in 1943. 4/ Thu following report presents the results of that project.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Minos has as its primary objective the more effective utilization of our mineral resources to the end that they make the greates possible contribution to national security and economy. It i the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lovell B. Moor, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallugiical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, Assistant Director."

Dec 1, 1946

By K. A. Johnson

Marshall and Bird have published the results of a cooperative investigation by the Bureau of Mines in which they developed a procedure for measuring the agglutinating value of coal.4 As stated in their paper, the procedure outlined was suggested by the early worn of Richters5 and Campredon,6 whose procedures were hurriedly modified to meet the need of an investigation then in progress. Since the publicatien of that paper, further work has been done in an attempt to show how the variables involved affect the concordance of the results, in order that such results may be obtained in different laboratories. Briefly, Marshall and Bird's method for determining the agglutinating value of coal consists in carbonizing an intimate mixture of 10 parts by weight of sand and 1 part by weight of coal in a porcelain crucible at a uniform temperature of 950° C. in a, vertical, cylindrical, electrically-heated furnace. After carbonization, the resultant buttons are crushed in a testing machine and the breaking strengths recorded in grams. The agglutinating value reported is the average breaking strength of 10 buttons. The coal for the test is prepared by crushing to pass a 100-mesh screen. The sand used as a diluent is sized between 40 and 50 mesh sieves with openings of 0.381 icon and 0.279 millimeters, respectively.

Jan 1, 1930

By D. A. Reynolds, L. P. Rockenbach

"The method of analyzing light oil for benzene is fully described by Fieldner and others 4/ and Kester and Kolmes 5/. In this procedure, benzene is determined by shaking 20 cc. of the 79º to 81º C. boiling point cut from the fractionation of the refined light oil with 3 volumes of 98—percent sulfuric acid in an A. S. T. M. separator funnel of the type used for determining water in bitumi¬nous materials. After the mixture has been shaken 5 minutes it is allowed to settle at least half an hour and the acid is drawn off; the residual oil is reported as paraffins and the decrease in volume as benzene. The method has been found satisfactory for light oils from coals carbonized at 5000, 600°, and 7000 C. but does not give accurate, reproducible results for oils from the 800° C. tests.The content of benzene of the 790 to 81° C. cut is high, 90 to 95 percent, for 800° C. light oils, whereas for lower—temperature light oils it is considerably less. Benzene is the most difficult of the aromatics to sulfonate, hence the acid concentration must be maintained above 95 percent to insure complete sulfonation. Sulfuric acid (98 percent) reacts with benzene, but its reaction with paraffins at ordinary temperatures is negligible; however, more concentrated acid will attack paraffins and give erroneous yields of benzene. The reaction between benzene and sulfuric acid forms water that will dilute the acid. The effect of this dilution may be overcome by increasing the acid-to-oil ratio or increasing the strength of the acid. The latter, however, must not be used, because the stronger acid reacts with paraffins."

Mar 1, 1942

By H. B. Brunot

A complete list of permissible mine equipment, tested and approved by the Bureau of Mines previous to January 1, 1947, was published as Information Circular 7432.2/ A list of permissible mine equipment tested and approved by the Bureau of Mines during the calendar years 1947, 1948, and 1949 was published as Information Circular 7569. The present list supplements Information Circulars 7432 and 7569 and includes all of 'the equipment approved during the calendar year 1950. Information Circular 7465, which included a list of permissible mine equipment tested and approved by the Bureau of Mines during the calendar year 1947 therefore is superseded.

Jan 1, 1951

By John R. Shattuck

As a part of the general chromite investigation in California designed to aid In the production of chromite during the recent war emergency, the Bureau of Mines explored the Coggins property in Siskiyou County, Work by the Bureau in cooperation with the Federal Geological Survey began in October 1942 and was concluded in March 1943. This report presents a brief history of the mine, outlines the physical features of the district, describes the deposits) and explains the work completed by the Bureau of Mines, Table 1 shows the analysis of diamond drill-hole samples. The logs of drill holes are in the appendix.

Jan 1, 1949

By H. B. Humphrey

In the 39 years from 1891 to 1929 , gas and dust explosions in the coal mines of Tennessee caused 413 deaths , or one- third of the fatalities in the mines for that period . Inasmuch as explosions caused but about 15 per cent of mine fatalities for the whole United States for this same period it is evident that the Tennessee coal mining record is by no means good , as far as explosion fatalities are concerned . Since 1926 , Tennessee has had a clear record as to fatalities from explosions ; this fact may be credited very largely to the improved conditions and safer practices in Tennessee's coal mines which have been brought about by the work of the State Inspection Department and of the Southern Appalachian Coal Operators Association directed toward adoption of safety precautions and practices most of which are advocated by the United States Bureau of Mines . Chief among these improvements are the replacement of black powder and dynamite by permissible explosives , improved ventilation , and the installation of rigid methods of inspection for gas . With the present tendency for operations to pass into the hands of responsible and informed management , and with unrelaxed care and inspection , the good record of the past several years should be maintained .

Apr 1, 1931

By John E. Shelton

The growing interest in beryllium as a structural material, and its in-creased use in recent years for atomic energy application, have led both government and industry to express concern over the inadequacy of the beryllium resources in the United States and the free world. Contemplated and proposed uses for this unique material will surpass the capacity of the domestic beryllium mining industry to supply raw material, which is presently extracted from relatively small deposits by hand sorting. The need for a simple beneficiation process for beryl ores has long been recognized by the Bureau of Mines, but to date no single process has proved satisfactory for treating deposits containing a sufficient tonnage of beryl ore to warrant commercial exploitation. As a part of the Bureau's continuing effort to develop an economical recovery process, this report describes flotation research on samples of beryl-bearing pegmatites from the George Roebling mine in Connecticut, and the Colony mine in New Hampshire. The study resulted in two methods of treatment to which the ores responded reasonably well.

Jan 1, 1961

By R. W. Huber

While conducting an investigation on electrolytic reduction of magnesium oxide in 1943, it became necessary to obtain accurate data on the conductivity and density of various mixtures of fused chlorides. AZ the required information was not available in the technical literature, or there were inconsistencies in the data from several investigators, an independent study was made at the Bureau of. Mines laboratory at Salt Lake City on the conductivity and density of the molten chlorides MgCl2, CaCl2, BaCl2, KCl, and NaCl and the binary mixtures of MgCl2 with the other four chlorides. Studies were also made on the binary system KCl-CaCl2 and on certain portions of several ternary systems. Measurements covered a temperature range from the melting point to 1,000° C. The results of this study were reported in an intra-Bureau report prepared early in 1944. Since then the Bureau of Mines has received several requests for data on fused chlorides; the results of the previous study, therefore, are being published to make the data available.

Jan 1, 1952

By Susan M. Moore

The objective of this study was to evaluate the circumstances leading to fall from equipment injuries in the mining industry. Method: The 2006 and 2007 Mine Safety and Health Administration annual injury databases were utilized for this study whereby the injury narrative, nature of injury, body part injured, mine type, age at injury, and days lost were evaluated for each injury. Results: The majority of injuries occurred at surface mining facilities (~60%) with fractures and sprains/strains being the most common injuries occurring to the major joints of the body. Nearly 50% of injuries occurred during ingress/egress, predominately during egress, and approximately 25% of injuries occurred during maintenance tasks. The majority of injuries occurred in relation to large trucks, wheel loaders, dozers, and conveyors/belts. The severity of injury was independent of age and the median days lost was seven days; however, there was a large range in severity. Impact on industry: From the data obtained in this study, several different research areas have been identified for future work, which include balance and stability control when descending ladders and equipment design for maintenance tasks.

Jan 1, 2009

By James A. Morgan

FIELD MEASUREMENTS OF NOISE WERE MADE ON THE PERIPHERY OF ENCLOSURES DESIGNED, MANUFACTURED AND INSTALLED BY INDUSTRIAL ACOUSTICS COMPANY, INC. ON THE SECONDARY TACONITE CRUSHER AT THE JACKSON COUNTY IRON COMPANY PLANT IN BLACK RIVER FALLS, WISCONSIN. NOISE REDUCTION ACHIEVED BY THE ENCLOSURES WAS SUFPICIENT TO PERMIT REDUCTION OF CRUSHER ROOM NOISE TO 90 DBA, PROVIDED THAT OTHER SOURCES ARE APPROPRIATELY TREATED AND ACOUSTICAL ABSORPTION IS PROVIDED IN THE CRUSHER ROOM. SECONDARY CRUSHER NOISE WAS REDUCED 10 TO 15 DBA BY THE ENCLOSURES.

Jan 1, 1980

By John M. Gomes

The Bureau of Mines investigated two techniques for removing CaO from scheelite (CaW04) prior to electrolysis. In the first technique, a crude tungstic oxide (WO3) containing 0.15-percent lime (CaO) was prepared by digesting scheelite concentrates in hot hydrochloric acid. This oxide was used as cell feed to produce tungsten of 99.9-percent purity. The second technique used a high-temperature, two-phase separation, resulting in extraction of 99 percent of the WO3 in the halide-tungstate phase, while 90 percent of the CaO was retained in the silicate phase. Tungsten of 99.9-percent purity was deposited from the halide-tungstate melt after B203 and NaPO3 were added to form an electrolyte. The two methods were compared with a previously developed technique of depositing tungsten from scheelite concentrate fed directly to the electrolytic cell.

Jan 1, 1971

By F. P. Haver

The Federal Bureau of Mines investigated aqueous electrolysis as a means for reducing lead chloride prepared by ferric chloride leaching of galena concentrate: NaC1 PbS + 2FeC13 ? PbC12 + 2FeC12 + S°. During electrolysis, metal was produced from solid lead chloride in contact with the cathode rather than from lead in solution. Relatively high current densities--up to 300 amp/ft2--were possible when operating in this way. A very simple cell, having a horizontal lead cathode at the bottom and a vertical graphite anode at the top, was employed. Lead chloride crystals, covering the cathode, were converted to metal powder during electrolysis, and chlorine gas or FeCls was produced at the anode, depending on the electrolyte composition. Electrolytes tried included aqueous solutions of HCI, NaCl, NH4Cl, and FeC12-NaC1. Optimum results (96-pct current efficiency, 0.23 kwhr/lb Pb) were obtained with 20 pct HC1 at 25° C, using a current density of 15 amp/ft2 and an electrode spacing of 1 inch. When the current density was increased, the energy requirement increased also but only to 0.41 kwhr/lb at 150 amp/fr3 and 0.58 kwhr/lb at 300 amp/ft2.

Jan 1, 1978

By V. R. Spironello

The Bureau of Mines is conducting studies of the slags related to ferrous technology to evaluate acceptable substitutes for the auxiliary flux, mineral fluorspar, in foundry operations. This work is directed toward the Bureau's goal of minimizing the Nation's dependence on scarce and critical minerals Comparative basic practice cupola (18-inch-ID) trials were made to evaluate a waste material called "used potlining," which contains significant levels of fluorine, sodium, and aluminum in various compounds. Used potlining is recovered from alumina reduction cells after its useful life, and was supplied by the Aluminum Co. of America (Alcoa) to the Bureau for evaluation. The material in the lump and pelletized form (with limestone) provided extremely fluid slags based on visual observation during cupola operation. No adverse effects were found on cupola performance, metal and slag chemistry, the environment, or mechanical properties of the castings produced. Fluorine recovery in the slag was equal to, or higher than, that of fluorspar; fluorine losses to the scrubber water and solids were lower. The acidity of the scrubber Hater was somewhat neutralized. No difference was observed in furnace-refractory attack, as determined by the level of magnesia in the slag and visual inspection. The recovery of sodium in the slag, presumably as the oxide, significantly increased slag fluidity, suggesting that less than equivalent fluorine may be required. There was no contamination of the gray iron by the aluminum from the used potlining. Used potlining was completely satisfactory as a substitute for fluorspar in cupola ironmelting.

Jan 1, 1981

By N. S. Dalal, X. Shi

"Electron spin resonance (ESR) spin trapping methodology has been used to study the reactions of manganese dusts with glutathione, employing a-{4-pyridyl-1-oxide)·N-tert-butyl-nitrone (PBN) and 5,5-dimethyl-1-pyrroline-N-oxide (DMPO) as spin traps. The results show evidence for the glutathionyl radical formation in the reactions of both MnO2 and manganese (Ill) acetate with glutathione. Based on these experimental observations, we hypothesise that the mechanism of neurotoxic effects of manganese might be due to the fact that the generation of glutathionyl radicals depletes the glutathione pool and reduces the glutathione shield against free radical products of dopamine metabolism and manganese induced reactive oxygenated species. IntroductionExposure to manganese compounds often occurs as the result of foundries and mining operations (1. 2). Other significant sources of environmental manganese include coal-fired power plants and burning of residual and crude oil (3, 4). Lately gasoline combustion has also started to contribute since manganese (methyl cyclopentadienyl manganese tricarbonyl. 0. 125 g/gallon) is being used instead of lead as an antiknock ingredient in automobile fuels (5. 6). Although manganese is an essential element in certain biological processes it is toxic in excessive amounts. The manganese toxicity is mainly associated with the nervous system (7-9). Symptoms frequently observed in manganese poisoning or manganism are disorientation, memory loss, anxiety, compulsive laughing and crying, mask-like faces, akincsia rigidity and tremor (10). In spite of numerous investigations to understand the mechanism of manganese induced injury. it has not been possible to localize the initial chemical lesion responsible for altered physiology and ultimate cell death. This may perhaps he the reason for failure in developing a successful therapy for manganese intoxication."

Jan 1, 1990

By John B. Umhau

In 1930 , 65,448 long tons of virgin or primary tin were consumed by 1,292 establishments in the United States , representing about 91 per cent of the total consumption as computed from imports , exports , and stocks at the beginning and the end of the year . The reported consumption was equivalent to 38 per cent of the world's tin production in 1930 , estimated at 171,000 tons , and was 12 per cent less than the 74,369 tons consumed by 1,307 establishments in 1928 . Decreased consumption of new tin in 1930 ás compared to 1928 was a reflection of the general industrial depression . All of the tin- consuming industries showed substantial decreases except tin plate and terneplate , white metal , and tinning , which showed small tonnage increases aggregating only 1,200 tons . The largest tonnage decrease was in the use of new tin in babbitt which declined 33 per cent in 1930 as compared to 1928. This was largely attributable to the decreased production of automobiles and trucks , which was 24 per cent lower in 1930 than in 1928. Percentage decreases in other important tin- consuming industries were as follows : Solder 18 per cent , bronze 19 per cent , tin foil 40 per cent , chemicals 23 per cent , tin oxide 44 per cent , and type metal 46 per cent . The distribution of the amount consumed by various uses during 1927 , 1928 , and 1930 is shown in table 1 . Consumption studies indicate the fact that variation in tin consumption from year to year parallels the fluctuations in demand for the already wellestablished tin products . For example , the manufacture of motor cars and trucks3 required only 11,000 tons of tin in 1930 compared to 19,000 tons in 1928 ; the canning industry continues to require the greater portion of the tin plate and much of the solder . Recently developed industries , while affecting total consumption of bearing metals , solders , etc. , to some extent , have made little change in the relative importance of these commodities as consumers of tin .

Jan 1, 1932

By A. J. Kraemer

[A great deal of interest has been manifested in the question of sulphur in fuels for automobile engines. Many different opinions have been expressed with respect to the effect of sulphur in gasoline on engine wear and engine performance. A wide difference of opinion exists as to the permissible limit of sulphur content for satisfactory operation.]

Jan 1, 1927

By R. J. Henry

This paper describing the mining practices at the Teck-Hughes mines at Kirkland Lake, Ontario, is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in various mining districts. HISTORY Prospecting was begun in the neighborhood of Kirkland Lake in 1906, but staking did not take place until 1911. Gold-bearing veins were discovered by surface trenching in 1913 on the mining claims which now make up the Teck-Hughes Gold Mines (Ltd.). A small mill was erected in 1916 after the completion of some underground exploration. A transmission' line was built in 1917 to the camp to provide adequate power for a vigorous underground campaign. Also in 1917 the present management took control operations since 1916 have been continuous,' with a steady increase in production to date.

Jan 1, 1930