Search Documents

By Philip C. Good

The Bureau of Mines investigated the feasibility of utilizing low-grade phosphatic shale as a feed for phosphoric acid production. Present practice in the phosphate mining operations of southeastern Idaho is to remove and either stockpile or waste low-grade phosphatic shales as the high-grade phosphate beds are selectively mined. Acid digestion studies were performed on uncalcined shale and on shale calcined to remove free carbon to determine phosphoric acid quality, yield, and amenability to filtration. The untreated shale, containing 21.4 pct P205, was digested with sulfuric acid in a single-tank reactor to yield phosporic acid and gypsum residue. Although 96 pct P205 recovery was attained in digesting uncalcined shale, only the calcined product gave satisfactory filtration rates. Calcined shale yielded phosphoric acid recovery of about 93 pct of the contained P205. It was higher in impurities than commercially prepared acid derived from high-grade western phosphate rock. An acid filtration rate of 745 lb P205/ft2/day was attained. This value is lower than the rate of 900 lb P205/ft that is generally considered to be acceptable in industrial production of phosphoric acid from high-grade phosphate rock.

Jan 1, 1981

By Shirley F. Colby

A continued rise in construction activity in 1941 forecasts further increases in the demand for building materials of mineral origin, Recent studies by the Bureau of Mines, United States Department of the Interior, reveal that sales of mine and quarry products and their derivatives as a class have followed the long-term trend of construction activity in the past and are benefiting now by the upswing in all types of building. At present most building materials of mineral origin are holding their own in the competitive arena. A few are slipping behind, but others have forged fax ahead. Prominent among those that have surpassed general construction activity since 1925 are sand, gravel, and crushed stone (used in concrete and road metal and railroad ballast) and cement. Both building stone and roofing slate have followed the building curve closely, although in the last few years sales of roofing slate have risen above the curve and sales of building stone have dropped below it. Clay products and building lime, on the other hand, have lagged behind the general procession. Gypsum sales likewise dropped behind, but during the last few years, this industry, thanks to the wider acceptance of its newer products, has staged a marked recovery so that it now stands in about the same relation to total construction activity as it did is 1927-25.

Jan 1, 1941

By C. H. Herty, J. K. Gaines

"Nearly every piece of electrical equipment used in mines ""breathes."" In other words, motors, controllers, rheostats, switches, and other similar equipment, even though encased in seemingly tight compartments, breathe in the atmosphere that surrounds them.As the apparatus is used, the temperature of metallic parts is changed generally in positive direction through the heat by friction and the heat due to the electric current. When the apparatus is idle it gradually cools down to the temperature of the surrounding atmosphere.This increase of temperature during operation and return to normal temperature when operation stops alternately raises and lowers the temperature of the atmosphere within the compartments which, in strict accordance with Charles' law -T = VT1 V'will expand or contract in proportion to any given temperature change.As compartments are not gas-tight, such expansion and contraction will force the atmosphere out of the compartment =on expansion and suck the surround¬ing atmosphere into the compartment during contraction, hence the term ""breathing.""Investigators of explosion-proof equipment have recognized that such an interchange would take place and have designed their equipment to safeguard possible explosions within the compartments."

Jul 1, 1927

By B. J. Scheiner

As part of the goal to maximize minerals and metals recovery from primary domestic resources, design factors associated with minimizing current leakage in bipolar cell configurations were studied by the Bureau of Mines as a means of improving the efficiency of bipolar e1ectrooxidation cells. Initial studies that were conducted in a small bipolar cell operating at 140 to 145 volts and 15.4 amp indicated how design factors could be employed to minimize cur-rent leakage around adjacent electrodes during cell operation. Based on these results, a 40-electrode, 108-kva prototype of an industrial-sized cell was constructed and tested for extracting metal values from offgrade molybdenite concentrates. The feasibility of recovering molybdenum and rhenium from the oxidized pulp also was determined. Feed to the process sequence consisted of flotation concentrates containing 16 to 35 pet Mo as molybdenite and 6 to 15 pct Cu. E1ectrooxidation in the prototype cell resulted in 84 to 97 pct Mo and Re extraction with a corresponding energy consumption of 9 to 13 kwhr/1b Mo extracted.

Jan 1, 1979

By R. L. Andrews

The Bureau of Mines investigated means of electrodepositing iridium to form thick coatings suitable for the protection of such metals as tungsten and molybdenum, which oxidize rapidly at high temperatures. Using a fused sodium cyanide bath, thick, adherent, and coherent deposits of iridium up to 15 mils thick were plated on tungsten and molybdenum substrates at 600° C and current densities of 10 to 100 ma/cm2. Limited oxidation testing of molybdenum encapsulated with pure iridium indicates that the coating may offer protection to approximately l,000° C in flowing air, but that at higher temperatures, the volatility of its oxide limits use of pure iridium. Alloy coatings of iridium with platinum, palladium, and rhodium up to 4 mils thick were formed from a fused sodium cyanide electrolyte; because their oxides are less volatile, these alloys may protect substrates at higher temperatures. Deposits made from aqueous electrolytes either had very low rates of deposition or were highly stressed and cracked when heavy deposits were made.

Jan 1, 1967

By Gerald L. Finfinger

The Bureau of Mines conducted an experimental degasification project in Island Creek Coal Co.'s Virginia Pocahontas No. S mine. Methane from the overlying Pocahontas No. 4 coalbed was entering mine workings in the Pocahontas No. 3 coalbed through fractures in the roof rock. Small-diameter (l-S/B-inch) holes were drilled into the overlying coalbed to reduce the gas pressure and intercept methane flows, which were piped to the surface through an underground 6-inch-diam steel pipeline. The total methane flow rate from the vertical holes averaged 150,000 ft3/day for the first month. Methane flows into the mine were reduced by 47 pet, thereby demonstrating the effectiveness of this form of degasification in reducing ventilation requirements and providing a safer working environment.

Jan 1, 1979

By Arnold O. Tanner

The domestic mining industry continued to be strengthened and revitalized in 1989. The healthy conditions and the industry comeback that began in 1987 continued to spread and became more established for many commodities. Relatively comfortable and stable commodity prices, still found predominantly in the metals sector, reinforced other operational factors in bringing vitality to the mining and mineral processing industries. New streamlined business practices, mine and plant modernizations, and the progressive use of new technologies successfully helped lower operating costs and increase efficiency during the past 5 to 7 years. An element common to these three factors of industry renewal and growth was the ever-increasing infusion of and growing dependence on constantly advancing computer technology applications. This trend of increasing computerization was occurring throughout the mining and mineral processing business while it similarly was in most facets of modern business and culture. Some commodities and companies still struggled to outlive sluggish prices and other unstable market conditions or to modernize their businesses, but increases in productivity and profits were more common. A trend toward increased mechanical excavation in nonsoil materials was beginning to surface as a substitute for standard cyclic mine development techniques, such as drill-and-blast and surface shovel-and-truck routines. More continuous mechanical excavation offered the potential for increased production, fewer people at the working face, better ground control, and generally improved safety. The main limitation was rock hardness. The construction industry had already recognized the benefits of tunnel-boring machines for long underground drives and mechanical planers for pavement removal. The Colorado School of Mines held a short course during the year entitled, "Mechanical Excavation Techniques in Mine Development and Production,'" which was at-tended by nearly 100 engineers from 12 countries. The consensus of attendees was that for the most efficient use of these machines and techniques, new mining plans needed to be developed beyond the simple adaptation of those excavators to existing mine plans.1

Jan 1, 1991

By R. L. Grayson, W. E. Wallace, T. Simonyi, J. C. Harrison

"Application of an SEM-based methodology suggests a reason for past contradictory results on the relationship between quartz and coal workers' pneumoconiosis (CWP). Results indicate that coal seams with the same bulk analysis of quartz may have different amounts of surface-availablequartz. Our research shows that the amounts of pure and surface-available quartz in a respirable dust vary directly with the rank of a coal seam, except in the case where rock materials are mined. The estimated amount of surface-available quartz therefore provides a measure of the quartz-related fibrogenic potential of a respirable dust.INTRODUCTIONFrom our previous work (Grayson, 1991), we have shown that the amount of pure quartz in a respirable coal mine dust sample appears to vary directly with the rank of the seam (using fixed carbon as the basis for comparison), except when a substantial rock parting, roof or floor are mined. Our other work (Wallace et al., 1989) showed that high-silica particles in a clay mine may generally be coated with clay, rendering the quartz core non-available for surface reaction in the lung. The combination of these findings led us to hypothesize that the coating phenomenon may indeed be present in coal mines as well, and that a rank relationship may be present regarding this phenomenon. Thus higher rank coal seams may have more surface-available quartz as well as more pure quartz particles in their respirable dusts. The scientific protocol for testing this hypothesis and the results obtained to date are discussed in this paper. Thus far, there is no reason to doubt that the relationship holds."

Mar 1, 1992

By Ellsworth Spencer

Noise induced hearing loss continues to afflict workers in many occupational settings despite longstanding recognition of the problems and well-known methods of prevention and regulations. Sound levels associated with heavy construction equipment range from 80 to 120 dB(A) and power tools commonly used in construction produce sound levels up to 115 dB(A).(1) The focus of this research was to determine the noise exposures of heavy construction equipment operators while documenting the workers’ tasks, (i.e. hauling, moving, and/or pushing construction material). Time-motion studies were performed at the construction sites and were used to correlate the noise dosage with the work performed by equipment operators. The cumulative dose for the operator was then plotted with references to work tasks, to identify the tasks that caused the greatest noise exposure. Three construction sites were studied for this research located in the western Pennsylvania and eastern Ohio areas. The types of construction equipment studied included asphalt pavers, backhoes, bulldozers, compaction equipment, excavators, haul trucks, telehandlers, and wheeled loaders. The results showed that bulldozer operators consistently had the highest noise exposures, ranging from a NIOSH REL (Recommended Exposure Limit) dose of 844% to 25,836% and an OSHA PEL (Permissible Exposure Limit) dose of 139% to 1,397%.

By Richard A. Watson, James A. Powell

A seismic system which utilizes in-mine geophones to detect trapped miners has been developed. Tests at the Bureau of Mines Safety Research Mine at Bruceton, Pa., and at two operating mines indicate such a system has a maximum detection range in excess of 1,000 feet. The system is field worthy and portable and requires less than 30 minutes to set up and check. Real-time detection is possible.

Jan 1, 1976

By D. L. Hollis

An arc plasma reactor, constructed and used for studying extractive metallurgical processing, was adapted by the U.S. Bureau of Mines to separate gases of different masses by using the high rate of plasma rotation. With argon and helium as input gases, peripheral reactor outlet ports had a measured average increase of about 10 pet in argon concentration relative to helium with the plasma on compared with plasma off for the same gas inlet concentrations in both cases. Approximately the same average increase in argon concentration occurred from the peripheral outlet port compared with a central outlet probe with the plasma on. There was no difference with the plasma off.

Jan 1, 2010

By John W. Frey

This paper presents one of a series of digests of foreign mining legis- lation and court decisions which is being prepared in advance of a general re- port relative to the rights of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the laws of Portugal, prepared from the best available information in Washington, has been slightly amplified in accordance with suggestions trans- mitted through the courtesy of the Department of State by Fred Morris Dearing, American Minister at Lisbon.

Nov 1, 1929

A spectrographic procedure applicable to the semiquantitative determination of 29 elements in tungsten is presented. The method is designed to give estimates of impurity concentrations up to 500 p.p.m. Limits of detectability range from 0.3 p.p.m. for the more sensitive elements to 100 p.p.m. for the less sensitive ones. Tungsten metal samples varying in particle size from minus 300-to 30-mesh are excited in the presence of 5 percent germanium with a direct current arc. Germanium acts to stabilize the arc, minimizes the volatilization of tungsten, and serves as an efficient carrier to sweep impurities from the tungsten into the excitation zone. Curves are presented that show the volatilization behavior of germanium, tungsten, and impurities in tungsten at different concentration levels. Data obtained were used as guides in establishing the method of analysis. In the absence of established reliable analytical procedures for determining many impurities in tungsten in the parts per million concentration range, the spectrographic method described here should prove to be helpful in evaluating high-purity tungsten.

Jan 1, 1961

By D. H. Baker

THIS REPORT presents the technique and equipment used in determining the hardness of titanium sponge. Detailed descriptions are given of the methods used in preparing test samples for chemical analysis and hardness testing, the method of melting and surfacing test ingots, and the technique of reading Brinell-hardness impressions. The arc-melting furnace described, for which engineering drawings are included, will produce from 70 to 90 double-melted buttons each 8 hours of operation. Experimental data are also presented depicting the effect on hardness of the methods of surfacing specimens, temperature of test specimens, and the effect of time at test load. These data show that surfacing of the specimen involves no critical machining operations but that the test surface must be paralleled by a relatively flat surface for contact with the anvil of the Brinell tester. The heating of a specimen to 150° C. during surfacing does not materially affect the results if the ingot is cooled to room temperature before the hardness impressions are made. The optimum time at load appears to be approximately 30 seconds, but load times of as much as 1/ ½ minutes will not cause major errors.

Jan 1, 1959

By David N. Montgomery

The characteristics of a closed cavity acoustic coupler were measured. Various configurations were investigated to determine their feasibility for use in a portable audio dosimeter calibrator.

Jan 1, 1976

By D. J. Bauer

This report covers a phase of an extraction project carried out as part of a research program on rare-earth technology. The current project--the production of pure cerium compounds--is an intermediate step between ore processing and metal reduction. In this connection, a study on a separatory-funne1 scale was made on nonreducing extractants for recovering cerium (IV) from tri-n-butyl phosphate (TBP) and of methods for recovering the cerium nitrate from the strip solution. Dilute sulfuric acid was found to be 100 percent effective in stripping cerium (IV). Several precipitants were effective in recovering the cerium from the strip solution, and ethanol was especially promising. A scaled-up investigation was made into the use of spray-tower type equipment to perform the function of extracting, washing, and stripping. This equipment, referred to as the pressure-bubbler, utilized the system developed on the separatory-funnel scale. Feed solutions were prepared from a bastnasite concentrate by two techniques. Of these, the sulfated bastnasite solution was most successful, resulting in 86-percent recovery of the cerium at 99.7+-percent purity.

Jan 1, 1959

By Hugo E. Camargo

In an effort to reduce Noise Induced Hearing Loss (NIHL) in the mining industry, the National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop noise controls for mining equipment whose operators exceed the Permissible Exposure Level (PEL). The process involves three steps: 1) Noise source identification (NSI), 2) development of noise controls, and 3) evaluation of the developed noise controls. For the first and third steps, microphone phased array measurements are typically conducted and data are processed using the conventional beamforming (CB) algorithm. However, due to the size and complexity of the machines, this task is not straight forward. Furthermore, because of the low frequency range of interest, i.e., 200 Hz to 1000 Hz, results obtained using CB may show poor resolution issues which result in inaccuracy in the noise source location. To overcome this resolution issue, two alternative approaches are explored in this paper, namely the CLEAN-SC algorithm and a variarion of an adaptive beamforming algorithm known as Robust Capon Beamformer (RCB). These algorithms were used along with the CB algorithm to process data collected from a horizontal Vibrating Screen (VS) machine used in coal preparation plants. Results with the array in the overhead position showed that despite the use of a large array, i.e., 3.5-meter diameter, the acoustic maps obtained using CB showed "hot spots" that covered various components, i.e., the screen deck, the side walls, the I-beam, the eccentric mechanisms, and the electric motor. Thus, it was not possible to identify which component was the dominant contributor to the sound radiated by the machine. The acoustic maps obtained using the RCB algorithm showed smaller "hot" spots that in general covered only one or two components. Nevertheless, the most dramatic reduction in "hot" spot size was obtained using the CLEAN-SC algorithm. This algorithm yielded acoustic maps with small and well localized "hot" spots that pinpointed dominant noise sources. However, because the CLEAN-SC algorithm yields small and localized "hot" spots, extra care needs to be used when aligning the acoustic maps with the actual pictures of the machine. In conclusion, use of the RCB and the CLEAN-SC algorithms in the low frequency range of interest helped pinpoint dominant noise sources which otherwise would be very hard to identify.

Jan 1, 2009

By G. St. J. Perrott, N. A. Tolch

"PURPOSE OF TESTSThe propulsive strength4 developed by the Cardox blasting device depends on the thickness of disk, weight of heater element, and weight of carbon dioxide charge. It might be supposed that the maximum weight of carbon dioxide that can be charged into the shell should give the greatest strength. However, according to the ballistic pendulum, the maximum weight of carbon dioxide with certain conditions of heater and disk has less propulsive strength than a smaller charge; in one condition of test a loss of 39 per cent in propulsive strength was noted. It is therefore of interest to study the effect of the variables that determine the strength of Cardox.ACKNOWLEDGMENTGrateful acknowledgment is made to A. B. Coates, associate mechanical engineer who developed the testing method for measuring pressures in the Cardox shell.DESCRIPTION OF DEVICEThe Cardox blasting device as fully described by the bureau in Report of Investiga¬tions 2920 (1929), consists essentially of hollow—steel shell, cylindrical in shape, an electrode, valve assembly, shearing disk, and discharge cap. The shell is prepared for use by inserting a heater element, closing the open end with a shearing disk, and screwing in place the discharge cap. The charge of carbon dioxide enters the shell through the electrode.The heater element is fired by an electric igniter of the match—head type. The heat released by the heater element completely gasifies the carbon dioxide and raises the pressure of the gas until it is enough to shear the disk."

Apr 1, 1931

By Raymond M. Stateham

Calculations based on data obtained from measurements of smoke from coal-fired powerplants predict that infrared imagers will be useful tools for smoke vision. Infrared imagers operating in the 3-to 5-um spectral region have been evaluated for this purpose. A mine opening 110 meters long was filled with smoke from burning coal, and two men, wearing breathing apparatuses, moved through the smoke to serve as targets. The men were detected and identified at 80 meters.

Jan 1, 1976

By Albert J. Rambosek

The objective was to obtain qualitative information on (1 ) the stress field in a core stub at the bottom, or face , of a cored borehole and (2 ) whether , and at what distance , in terms of core diameters from the face of the borehole , relief of stresses in the core is complete . The photoelastic and brittle lacquer techniques of stress analysis were used to determine the pattern of stresses in two- dimensional models , simulating the bottom of a borehole with a projecting stub of core . The core was stress- free at 1-1 /2 core diameters or more from the face of the simulated borehole . The analyses of the isoclinic and isochromatic patterns in the core near the face of the borehole reveal why core occasionally breaks into thin plates , when core or stress - relief drilling is attempted in highly stressed rock masses , such as heavily loaded mine pillars . stub broke away from the bottom in a hydrostatically loaded artificial rock specimen in a manner indicating that core " wafering" can result from tensile stresses developed in the core when a coring bit penetrates the highly stressed rock mass .

Jan 1, 1964