Search Documents

By G. R. Strimbeck

The Federal Bureau of Mines has been developing processes for producing synthesis gas directly from coal, oxygen, and superheated steam. An atmospheric-pressure pilot plant was constructed and operated to: 1. Determine the operability of the plant for gasifying coals of different ranks under various operating conditions. Listed in decreasing order of rank, these coals included a Pennsylvania anthracite, a bituminous A coal from the Sewickley bed, West Virginia, and a subbituminous C coal mined in the Lake de Smet region of Wyoming. 2. Determine the effect of varying operating conditions on: (a) Standard cubic feet (std.c.f.) of oxygen and pounds of coal of different rank required to make M std.c.f. of product gas (carbon monoxide plus hydrogen); (b) carbon gasified, percent; (c) exit-gas temperature, degrees F.; and (d) heat loss, B.t.u. per pound coal. 3. Compare the gasification characteristics, indicated in item 2, of coals of different rank: Bituminous A, anthracite, and subbiturninous C. 4. Determine the concentration of dust in the gases produced and the efficiency of dust removal, and investigate the relation between the sulfur content in the coals gasified and the gases produced.

Jan 1, 1960

By K. E. Tame

As part of a Bureau of Mines survey of radioactive waste disposal , a laboratory investigation was made to study such problems in carbonate leaching mills . Because uranium concentrators employing carbonate leaching with caustic precipitation normally recycle barren solutions to the washing circuit , the disposal of liquid radioactive wastes is automatically controlled . However , it was deemed important to determine the actual radium 226 concentrations occurring in this type of milling so that the survey of the entire industry would be complete . The laboratory procedure consisted of leaching the ground ore at 85 ° to 90 ° C and 50 pct solids for 6 hours in a sodium carbonate - sodium bicarbonate solution . The pulp was filtered to obtain a pregnant solution that was reacted with sodium hydroxide to precipitate the uranium as sodium diuranate . Regeneration of the barren solution was accomplished by gassing with carbon dioxide . The solution then was reused by advancing the solution through the washing to the leaching operations . The radioactivity in the pregnant solution was unusually high , averaging 6,500 disintegrations per minute ( dpm ) of radium 226 per liter . However , over 95 pct of the radium was precipitated with the uranium . Consequently , no buildup of radium occurred upon reuse of the barren solutions for washing .

Jan 1, 1964

By R. W. Dalzell

The performance characteristics, efficiency, and operating pressure of jute line-brattice systems were studied under varying underground conditions; various fabric grades and installation methods were used. The test results indicate that line-brattice system efficiency is dependent upon the method of ventilation the method of installation, porosity of fabric, and size of tight rib area.

Jan 1, 1966

Viable domestic mineral industries are essential to the economic health of the United States and the well-being of its citizens. The charts in this publication reflect developments significant to the Nation's mineral industries during 1975. Last year was a year of reduced activity for the Nation's mineral industries. Although the value of the country's total mineral output rose, for example, the overall production and use of many minerals fell. At the same time, the industry experienced lower profits and higher debt/equity ratios. These and other adverse effects on many segments of the Nation's mineral industries resulted from the overall decline in domestic and international economic activity.

Jan 1, 1976

By Bernard Porter

The solubility of UO2 was determined at 1,250° C. in ternary melts of UF4 and BaF2 with CaF2, LiF, and SrF2. The solubility of Ce02 was measured at 800° and 850° C. in a solution of CeF3, BaF2, and LiF. The amount of La203 which dissolves at 950° C. in a binary mixture of LiF and LaF3 and a ternary of LiF, LaF3, and BaF2 was also measured. In each case, the amount of soluble oxide was mound to be less than 5 weight-percent. A procedure was developed for filtering fused, oxide-saturated fluoride melts in order to obtain a representative sample for chemical analysis. The oxide content of the samples was determined by an inert-gas fusion procedure.

Jan 1, 1961

By Eugene Frey

The Romur is one of several properties in the Copper Mountain mining district, Fremont County, Wyo., that contain scheelite deposits. The district lies on the southern slope of the Bridger Mountains, 18 miles northeast of Shoshoni and 15 miles from the rail point at Bonneville on the Chicago, Burlington & Quincy Railroad (figs. 1 and 2). The tungsten deposits occur in a zone of pre-Cambrian schists and gneisses that have been cut by numerous basic dikes and granite pegmatite dikes. Scheelite occurs in lenses and pods that lie parallel to the foliation and bedding in the metamorphic rocks. The more important deposits are found in a lime-silicate rock consisting primarily of zoisite but with small quantities of quartz and carbonate. Scheelite was found in December 1941, and the area was mapped by the U. S. Geological Survey early in 1942. In November 1942 the Bureau of Mines commenced work on the Stardust-Comet group for the purpose of developing reserves for war requirements. The initial work consisted of driving an alit in the ore zone a distance of 109 feet. This zone was sampled during the progress of the work, and subsequently surface and underground exposures on adjoining properties also were sampled (figs: 5, 6, 7, and 8). One hundred twenty-four samples were obtained. Sample and assay data are shown in tables 2, 3, and 4.

Jan 1, 1950

By John P. Capp

Addition of sintered fly-ash/bottom-ash mixtures to rubber formulations failed to increase the skid resistance of the resulting products. Wear, tensile and hot-tear strengths, and resilience of the ash-rubber material, as determined in laboratory tests, were significantly less than that of comparable rubber. The material appeared unsatisfactory for automobile and truck tire manufacture, but might prove suitable as a filler in other rubber goods. Raw fly ash could not be satisfactorily compounded with rubber.

Jan 1, 1972

By R. W. Van Dolah

An important function of stemming used to confine explosives in shot holes in underground coal mines is to minimize the chance of ignition of firedamp or coal dust by the detonation products. Until 1952, the Bureau of Mines approved only the use of fireclay or similar incombustible material for stemming permissible explosives. At least 2 feet of stemming were required except in holes less than 4 feet deep; in such short holes the stemming was required to be half the depth of the hole. Over the years, several special stemming devices have been proposed in the United States as substitutes for fireclay. Many economic and safety advantages were claimed for these devices, but only one approved device has been marketed in this country. Bureau requirements for stemming explosives in coal mines were modified at that time to permit the approved stemming device to be used as a substitute for the required fireclay.

Jan 1, 1961

By Marcia L. Harris

The National Institute for Occupational Safety and Health (NIOSH), as part of its continuing research program for evaluating coal dust explosion hazards, has investigated several areas in which current practices may need to be updated in order to adequately protect mines against coal dust propagated explosions. In the United States, current rock dusting requirements remained largely unchanged since 1969. US Title 30 Code of Federal Regulations Section 75.403 is based on a coal dust particle size survey performed in the 1920s and later was supplemented by full-scale testing of the rock dust ability to inert a coal dust explosion. NIOSH recently conducted a comprehensive survey of US underground coal mines to determine the range of coal particle sizes found in dust samples collected from the mine entries. Due to advancements in technology and modern coal mining techniques, the current coal dust particles in intake airways are significantly finer than those found in the mines in the 1920s. According to past full-scale dust explosion test results, the current rock dusting practices used in today?s mines to inert a coal dust explosion may not be adequate. Other closely related issues such as rock dust testing methods and sampling procedures are discussed.

Jan 1, 2009

By E. G. King

Existing thermodynamic data for compounds of the rare-earth metals are few in number and often inaccurate because, in the past, it was difficult to obtain samples that were pure enough and reasonable in cost--a situation that is rapidly improving. This paper reports the results of low-temperature heat-capacity and high-temperature heat-content measurements for cerous fluoride (CeF3) and supplies the first such published data for a rare-earth fluoride. The low-temperature heat-capacity data cover the temperature range 51°-298° K. and serve to evaluate the entropy at 298.15° K. The high-temperature heat-content data cover the temperature range 298°-1,799° K., including the temperature and heat of fusion. The results are assembled for ready use in thermodynamic calculations. Cerous fluoride is one of the important intermediate compounds in the production of cerium metal.

Jan 1, 1959

By S. P. Kinney

During 1925, at Holt, Ala., the United States Bureau of Mines made a study of the composition of the gases at four elevations in the shaft of a furnace producing foundry iron. A report3 of the work was published in 1927. Some of the results of this investigation are shown in Figure 1. As indicated, the gas at the center of the shaft is low in CO2 content, while the gas in the vicinity of the wall is higher in CO2. The composition of the gases at the top and at the center of the stock column was not far different from the composition of the gas at the top of the bosh. The investigation indicated clearly that lean gas was channeling through the center of the column. More recently the study was enlarged in scope to include investigation of a furnace operating on Lake Superior ores in the Chicago district. A series of planes between the stock line and tuyères was surveyed. Means and apparatus were developed for obtaining, between the inwall and the center of the furnace, the gas composition, gas velocity, and temperature on each plane. A complete report4 of the investigation has recently been published.

Jan 1, 1929

By Jerry E. Olson

In 1984, the U.S. Bureau of Mines conducted a mineral survey of the Black Rock Desert Wilderness Study Area (WSA) (NV-020-620), which covers approximately 319,000 acres in Humboldt County, Nevada. About 90% of the WSA is underlain by Pleistocene desert playa sediments; the remainder is comprised of Jurassic-Triassic metamorphic rocks, a Cretaceous intrusive and Tertiary volcanic rocks. Most of the WSA is within a down-dropped fault block of the Basin and Range physiographic province. No mines or evidence of major exploration were identified within the WSA; but five claim blocks within or adjacent to the WSA and zones of anomalous character as defined by the Bureau of Land Management were examined. No mineral resources were identified, but anomalous gold, silver, and indicator element content of samples taken near Pinto Hot Springs indicate resources may exist. Lithium content of samples from near-surface sediments on the desert playa is too low for resources, out geologic conditions are favorable for higher concentrations at depth. Occurrences of zeolites are not considered to be of commercial interest. Approximately 27,000 acres are held under geothermal lease, and most of the WSA is of interest for oil and gas. No evaluation of these commodities was made by the Bureau of Mines

Jan 1, 1985

By J. D. Davis

"Introduction.Sixty years ago, M. Berthelot found that ethylene could be selectively absorbed from gaseous mixtures by concentrated sulphuric acid, and that the compound formed by the chemical union of the gas and acid was readily decomposed by heating with water, yielding ethyl alcohol. Only within the last few years has there been any attempt to make use of this discovery technically.Bury*, working in England at the Skinningrove Iron Works and on a commercial scale, developed a technical method for converting, the ethylene of coke-oven as into alcohol. With a gas containing less than 3 per cent of ethylene, he obtained a yield of 1.6 gallons of alcohol per ton of coal carbonized.De Loisy** perfected a technical method for treatment of coke-oven as for alcohol. Evidently this work was carried out on a semi-commercial scale. His method is based on the use of catalytic agents for hastening the absorption of ethylene by sulphuric acid. He uses part of the spent acid for drying the gases and pact for the manufacture of ammonium sulphate. Excess acid is reconcentrated by waste heat. Others have worked on the problem, but so far there has been no large recovery of ethylene from coke-oven gases. The chief difficulty seems to lie in the low efficiency (about 50% of methods and tae relatively low concentrations of ethylene in the gases treated. Gas from Trent amalgam*** contains much larger percantages of ethylene than does coke-oven gas, as Will presently be shown, and if it should ever prove practIcal to treat industrial ;as for alcohol, this gas would offer attractive possibilities,* Bury, Ernest, Ethylene as Alcohol from Coke-Oven Gas: Gas Journal' Vol. 148, D. 30, 1919, pp. 718.** DC Loisy, M.E., Sur un procede' industrial de fabrication syntlotique de l'alcool et de l'ether a partir des gaz de distillation de la houil Comp Rend, vol. 170, Jan. 1920, p. 50-3.*** A paste consisting of approximately part oil such as that obtained as for cleaning coal. See Perrott. in cleaning coal, Chem 3 parts finely pulvarized coal and 1 final product in the Trent, process StJ, and Kinney, S.P. The use of oil Vol. 35 August 3, 1921, p, 183.. & Met."

Nov 1, 1922

By Lawrence W. Scott

The performance of RETIMET metal foam as a flame arrester on explosion-proof enclosures was investigated by the U.S. Bureau of Mines both in laboratory tests and at the U.S. Mine Safety and Health Administration's (MSHA's) Approval and Certification Center, Triadelphia, WV. The objective of this research was to develop a permissible pressure vent for use on lightweight, vented, explosion-proof enclosures. In laboratory tests, four grades of RETIMET, a stainless steel foam material, were evaluated: (1) 45 NC-7, (2) 45 NC-13, (3) 80 NC-7, and (4) 80 NC-13. Explosive gas mixtures were prepared by a dynamic flow system. Ignition was by a low-voltage arc. Each grade of RETIMET metal foam successfully arrested the flame front in all methane-air tests. To evaluate RETIMET metal foam on large, commercial size enclosures,a multi compartmented enclosure was designed and tested in MSHA's explosion gallery in Triadelphia, WV. Extensive explosion testing revealed that a minimum vent-area-to-enclosure-volume ratio of 11.33 in2/ft3 is required to keep internal pressure rises below 3 psig. The RETIMET metal foam functioned satisfactorily in all tests as evidenced by the absence of external ignitions.

Jan 1, 2010

By Robert J. Evans

The Hopper-Feeder-Bolter (HFB) is a prototype multifunctional machine designed to improve productivity by minimizing continuous miner place changes. It is designed primarily to work beside a two-pass continuous miner, bolting on one side and then place changing to bolt the other side while simultaneously providing a surge car and lump breaker located directly behind the continuous miner. Surface testing was conducted at the Bureau of Mines Mine Equipment Test Facility (METF) to evaluate overall system performance and reliability. Tests were conducted to evaluate place changing, tramming, lump breaking, roof bolting, drawbar pull, conveying, temporary roof-support (TRS) capacity, lighting, and noise. Surface test results indicate the HFB is ready to be tested and evaluated underground in a production mode.

Jan 1, 1988

By J. L. Stauffer, S. L. Lacey, L. J. Gaydos, L. M. Demers, D. C. Kuhn

"Tumor necrosis factor alpha (TNFa) and thromboxane A2 (TXA2) are major products of the activated alveolar macrophage and serve as key mediators of lung injury. In order to determine if the synthesis ofTXA2 and the release ofTNFa are associated, the production of these inflammatory agents by the human alveolar macrophage (AM), as a result of activation by lipopolysaccharide (LPS), was assessed in the absence and presence of the thromboxane synthase inhibitors UK 38,485 (Dazmegrel) and OKY 046. UK 38,485 and OKY 046 inhibited both LPS-stimulated TXA2 production and TNFa release in a dose-dependent manner. Prostaglandin E2 (PGE2) production was not increased by UK 38,485 or OKY 046. Neither LPS nor UK 38,485 had any effect on LT84 production by AM. Neither UK 38,485 or OKY 046 had any effect on LPS-stimulated interleukin-I beta release. However, the TXA2 mimetic, U46619, did not stimulate TNFa release by AM either in the absence or presence of UK 38,485. These findings suggest that 1) UK 38,485 and OKY 046 are inhibitors of both TXA2 production and TNFa release by activated human AM, 2) UK 38,485 probably does not exert its inhibitory action on TNFa release through effects on eicosanoid production and 3) the possibility that TNFa- and TXA2-induced lung injury may be subject to amelioration by imidazole-based compounds should be further evaluated.IntroductionTumor necrosis factor alpha (TNFa), produced by monocytes and macrophages, is a potent peptide mediator of lung injury (1,2). The exaggerated release of TNFa has been implicated in the etiology of acute lung reactions such as septic shock of bacterial or viral origin (3,4). The role of TNFa is expressed primarily through its ability to activate a variety of cell types within the lung environment including polymorphonuclear leukocytes (PMNs, ref. 5), type II epithelial cells (6) and fibroblasts (7). The role of lipid mediators in lung disease has also been extensively characterized (1). In particular, the relationship between pulmonary inflammation and fibrosis and the production of oxygenated derivatives of arachidonic acid (here termed ""eicosanoids"") appears to be a key factor in a variety of disease processes in the lung (8). The alveolar macrophage (AM) synthesizes primarily prostaglandin E2 (PGE2). thromboxane A2 (TXA2) and leukotriene 84 (LT84, ref. 9). These eicosanoids have been shown to produce a variety of effects in the lung including bronchial smooth muscle dilatation (PGE2, ref. 10), vascular smooth muscle contraction and platelet aggregation (TXA2, ref. 11) and oedema and immune cell extravasation (LT84, ref. 12)."

Nov 1, 1995

By Jalna R. Zatko

The Bureau of Mines has developed and constructed an apparatus that is capable of measuring concentrations of high-molecular-weight polymers in solution at 10 ppm and less. A means for determining low concentrations of polymeric solutions was devised that was independent of slight fluctuations in solvent quality in order to measure polymers in effluent prior to recycling of the recovered solution. The concentrations of polymers ore related to a measured pressure drop observed during turbulent flow of the solution. Low concentrations of polymers of ethylene oxide and acrylamide (frequently used as flocculants for clay waste systems) in aqueous and salt solutions have been successfully measured on the apparatus constructed by the Bureau.

Jan 1, 1981

By S. C. Schaefer

Thermodynamic properties of indium oxide (In203) have been studied with a high-temperature galvanic cell employing stabilized zirconia electrolytes. In the temperature range 790° to 1,230° K the free-energy change for the cell reaction 21n(1) + 3Cu20(c) = In203(c) + 6Cu(c) together with the standard free energy of formation of cuprous oxide gives the standard free energy of formation of indium oxide from the elements as ?Gf° = -218.78 + 75.34 X 10-3T ±0.7 kcal/mole. A third-law analysis yields the standard enthalpy of formation: ?Hf°298.15 = -221.5 kcal/mole.

Jan 1, 1971

By Wilbert J. Huff

The Explosives Division of the United States Bureau of Mines makes certain laboratory and field investigations that deal with explosions, explosives, ignition, and combustion, together with many related problems, such as the cause and prevention of fires, and certain fundamental scientific questions bearing upon the determination of the chemical and physical mechanisms underlying some of the important phenomena encountered. Its work on explosives has been particularly directed toward determination of the chemical and physical characteristics of explosives designed for use in coal mines and in a more limited way to those used in metal mines, tunnels, quarries, and other engineering operations. This testing is handled by two units of the Explosives Division, as follows:

Jan 1, 1937

By K. C. Dean

Time and motion studies were made by the Federal Bureau of Mines on the hand and machine dismantling of scrapped auto starter motors, generators, and alternators for recovery of copper, aluminum, and iron. The studies showed that an individual with power handtools and convenient access to a hydraulic press, power bandsaw, acetylene torch, and power lathe could, in an 8-hour day, disassemble about 100 starters, or 150 generators, or 30 alternators. The scrap copper yield would be 280, 390, and 45 pounds, respectively, and the iron yield would be about seven times the copper weight. About 100 pounds of aluminum would be obtained from the alternators.

Jan 1, 1976