Search Documents

By F. Matanzo

This guide considers only nine of the many wire rope terminations used in the mining industry so use of the information presented for terminations not specifically addressed can be done, but with some risk. The nine terminations considered are: Flemish Loop with Steel Sleeve & Thimble, Flemish Loop with Steel Sleeve, Wedge Socket, Swaged Socket, Turn Back Loop with Aluminum Sleeve & Thimble, Thimble Splice with Four Tucks, V-Bolt Clip with Thimble, Zinc Poured Socket, and Epoxy Resin Poured Socket. The guide uses pull test data, axial fatigue test data, and data on sensitivity to poor workmanship, to rank the nine terminations with respect to these performance measures. A selection procedure is suggested and illustrated with an example. Failure data is used to identify the common modes of failure of each termination and so help the inspector direct his attention to the likely location for a failure and describe what he should be looking for. The data on which this guide is based is included so that as new data becomes available, the ranking order can be adjusted accordingly.

Jan 1, 1978

By James P. Ludwig

This report provides the results of a two year study of the projected time and cost requirements for new mine development in Wisconsin and is based on a unique blend of information from mining company officials, state regulatory agency officials and contractor experience. Through formal cooperative and review agreements with Kennecott Copy per Corporation, Exxon Minerals Co., U.S.A. and Noranda Mines Ltd., and the Wisconsin Department of Natural Resources plus informal arrangements with knowledgeable Wisconsin persons, lists of the tasks and subtasks required to plan a new mine in Wisconsin were developed. Times and costs were assigned to all tasks and subtasks and these data reviewed by all cooperators. Critical Path Method Diagrams were then developed for a generalized mining project. Total time and cost for the premine planning process was estimated to be 25..1 years and 223 person-years of professional time excluding public affairs effort respectively. By eliminating redundancies in the process and by increasing project efficiency through early public review and participation, recom¬mendations were made to lessen the time and lower the cost of premine planning. The streamlining recommendations could shorten the overall critical path length to 18.16 years and lower the cost to 208 person-years of professional time excluding public affairs effort. The estimated distribution of professional effort (cost) for mine planning in Wisconsin approximates 50.5% for traditional mine engineering tasks, 36.6% for environmental-regulatory tasks and 12.9% for traditional geological-exploration tasks.

Jan 1, 1979

By Robert A. Cortese, Henry E. Perlee

Coal dust and float coal dust, produced during normal mining operations, in underground coal mines, are carried from the point of origin downstream by the ventilating air, where it deposits on the surfaces of the mine entry. In an explosion, this dust is lifted from the surfaces by the aerodynamic disturbances and, if of sufficient quantity, can continue to propagate the explosion. To prevent the surface coal dust from contributing, it must be inerted, typically by spreading pulverized limestone, i.e., rock dust, over the coal dust surface. To facilitate the dusting operation, the National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory(PRL), developed an automated system that continuously monitors the accumulation of coal dust. This system could activate a rock-dusting machine that disperses rock dust into the ventilation air when dangerous deposits accumulate and deactivate the machine when sufficient inert has been deposited on top of the coal dust. The system consists of a microprocessor-controlled optical float dust deposition meter. This device measures the light intensity reflected from a deposited layer of dust. A standard cap lamp is used as a fixed-position light source. From the reflected light signal, the microprocessor determines the hazard level of the deposited layer and performs the appropriate action. Full-scale studies conducted in the Experimental Mine at PRL's Lake Lynn Laboratory, using alternating thin layers of rock dust and coal dust, successfully demonstrated the operation of the device. Based on the statistical data from these studies, a mathematical model was developed to predict long-term error in total rock dust content using this inerting procedure. Downwind dust dispersion was also examined to provide optimum placement of the dust sensors and to determine the need for better rock dust dispersion techniques.

Jan 5, 1998

By Staff

A major emphasis of the U.S. Bureau of Mines is to perform research on the prevention of fatal accidents at mining operations. The leading cause of fatalities in the underground coal mining industry is groundfalls. This proceedings volume presents several new developments that are helping to prevent fatalities and reduce injuries by groundfalls. The papers focus on the problem from two different perspectives. About half of the papers present information and techniques that can be used to train and motivate miners to protect themselves from groundfalls. The other papers explain how to identify and respond to various geologic conditions that affect the stability of the mine roof. Of the 95 groundfall fatalities that occurred during 1986-90, 75% took place in Kentucky, West Virginia, and Virginia. The rate of groundfall fatalities was much higher at small mines. During 1986-90, the rate of groundfall fatalities at mines employing fewer than 20 people was 4.3 times higher than the rate for larger mines. Because so many groundfall fatalities are occurring at relatively small mines in the southern Appalachian coalfields, many of the papers focus specifically on the needs of this category of mine operations.

Jan 1, 1992

By Oliver C. Ralston, Dorsey A. Lyon

The data reported in this bulletin are largely the result of experiments conducted by the Salt Lake City station of the Bureau of Mines in cooperation with the department of metallurgical research of the University of Utah. The work on lead is only one of the phases of the investigations carried on at that station during the years 1914 to 1916. The results of similar work with zinc ores and with copper and other ores will be published in future reports of the bureau.

Jan 1, 1918

By Albert L. Toenges

The production of bituminous coal by stripping methods has become an important factor in some areas, especially in the Central and South Central States. In the latter, production at strip mines exceeds that at deep mines. Table 1 shows the tonnage produced at strip mines and the percentage of the total production for 1924 to 1935, inclusive, for the States in which the mines described in this circular are situated.4/ Following are references to earlier Bureau of Mines publications on strip mining of bituminous coal: Cash, F. E., and von Bernewitz, M. W., Methods, Costs, and. Safety in, Stripping and Mining Coal, Copper Ore, Iron Ore, Bauxite, and Pebble Phosphate: Bull. 298, Bureau of Mines, 1929, 275 pp. Kiessling, O. E., Tryon, F. G., and Mann, L., The Economics of Strip-Coal Mining: Econ. Paper 11, Bureau of Mines, 1931, 32 pp. Turner, Scott, and Bureau of Mines Staff; Mining Bituminous Coal by Stripping Methods: Inf. Circ. 6383, Bureau of Mines, 1930, 23, pp.

Jan 1, 1937

Research 83 highlights significant studies conducted during the past fiscal year at Bureau facilities and offices. Readers who want more information about the projects and studies summarized here can contact the researchers whose names and locations appear with each summary, General information on Bureau of Mines programs is available from the Office of Technical Information, 2401 E Street, NW., Washington, DC 20241. A listing of principal officials, a location map of field facilities, and a selected bibliography of publications and patents issued on Bureau developments during the past 3 years are provided.

Jan 1, 1983

By M. M. Gilkey

This report on water requirements for the New Mexico mineral industry includes data on industrial operations closely related to mineral production. It contains general information concerning public water supplies at five principal cities and a short discussion of water needs for agriculture. Background data are presented regarding the geography, hydrography, and water laws of New Mexico, as well as precipitation and evaporation characteristics of the State. Most of the information on source, quantity, distribution, cost, and treatment of water was obtained in interviews with company representatives. Water systems at 46 operations are illustrated by schematic waterflow diagrams. The study revealed that the New Mexico mineral industry in 1962 used about 16 billion gallons of new water and reused 152 billion gallons, a total usage of 168 billion gallons. Consumption amounted to 7.6 billion gallons. Of the 16 billion gallons of new water, 11.9 billion gallons was "self- supplied" from ground water sources, and 2.6 billion gallons was self supplied from surface sources. Approximately 1.5 billion gallons was purchased. Some of the water from company-owned wells is piped as far as 30 miles. Reported costs of the self-supplied new water range from 1 to 20 cents per 1,000 gallons and average 8 cents per 1,000 gallons for power and maintenance. Inadequacy of the supply of new water at many operations necessitates large-scale recirculation. Reported costs for recirculating water (power and maintenance) average 1.8 cents per 1,000 gallons. For the entire New Mexico mineral industry in 1962, the value of product was $42 per 1,000 gallons of new water intake and $88 per 1,000 gallons consumed. Analyses of 40 water samples, listed in the appendix, show the wide range in water quality at plants throughout the State. Projection of the 1962 water requirements of the mineral industry indicate that the total demand for new water will increase from the 16 billion gallons used in 1962 to 24 billion gallons in 1980, a 50 percent increase; and to 36 billion gallons in 2000, which is 125 percent more than the 1962 intake of new water.

Jan 1, 1965

By M. M. Gilkey

This report on water requirements for the New Mexico mineral industry includes data on industrial operations closely related to mineral production. It contains general information concerning public water supplies at five principal cities and a short discussion of water needs for agriculture. Background data are presented regarding the geography, hydrography, and water laws of New Mexico, as well as precipitatton and evaporation characteristics of the State. Most of the information on source, quantity, distribution, cost, and treatment of water was obtained in interviews with company representatives. Water systems at 46 operations are illustrated by schematic waterflow diagrams. The study revealed that the New Mexico mineral industry in 1962 used about 16 billion gallons of new water and reused 152 billion gallons, a total usage of 168 billion gallons. Consumption amounted to 7.6 billion gallons. Of the 16 billion gallons of new water, 11.9 billion gallons was "self- supplied" from ground water sources, and 2.6 billion gallons was self supplied from surface sources. Approximately 1.5 billion gallons was purchased. Some of the water from company-owned wells is piped as far as 30 miles. Reported costs of the self-supplied new water range from 1 to 20 cents per 1,000 gallons and average 8 cents per 1,000 gallons for power and maintenance. Inadequacy of the supply of new water at many operations necessitates large-scale recirculation. Reported costs for recirculating water (power and maintenance) average 1.8 cents per 1,000 gallons. For the entire New Mexico mineral industry in 1962, the value of product was $42 per 1,000 gallons of new water intake and $88 per 1,000 gallons consumed. Analyses of 40 water samples, listed in the appendix, show the wide range in water quality at plants throughout the State. Projection of the 1962 water requirements of the mineral industry indicate that the total demand for new water will increase from the 16 billion gallons used in 1962 to 24 billion gallons in 1980, a 50 percent increase; and to 36 billion gallons in 2000, which is 125 percent more than the 1962 intake of new water.

Jan 1, 1965

By R. L. Levens

The Underground Injection Control program was promulgated in 1981 by the U.S. Environmental Protection Agency under the provisions of the Safe Drinking Water Act. Placement of mine waste backfill underground is considered underground injection under the provisions of this program. A major issue is whether mine waste that is regulated as a contaminant source on the surface should be disposed of underground. The U.S. Bureau of Mines conducted research to investigate the impacts of mine waste sandfill on the quality of ground water. Analyses of water samples collected before and after contact with sandfill in a 10-year-old stope, as well as samples of the sandfill itself, were used to ascertain the influence of the sandfill after mine closure and subsequent flooding. Computer models supported the hypothesis that oxidation of pyrite by oxygen, accompanied by dissolution of carbonates, was the predominant reaction controlling the quality of the water being discharged from the stope. Concentrations of metals released as a result of acid production remained near or below detection limits. Metals release after mine flooding is expected to remain low as a result of the buffering by the sandfill and the reduced rate of oxidation.

Jan 1, 2010

By R. C. Adams

This report describes the feasibility of mining the oil shale deposits of the Piceance Creek basin in Colorado by an integrated open pit system. The study is based upon a comprehensive analysis of pertinent environmental, economic, and engineering factors. Ten mining cases are investigated, and the mine design and cost estimates for each case are presented in this report. Nine of the cases represent three cutoff grades, defining oil shale ore as equal to and above 15 gallons per ton (gpt), 20 gpt, and 25 gpt at three ore production levels of 500,000 tons per day (TPD), 1,250,000 TPD, and 2,500,000 TPD. The tenth case is an alternate design of the 500,000 TPD production rate at the above 15 gpt cutoff grade. The report consists of Volume I, a technical and cost comparison of the ten cases; Volume II-Part I, a detailed explanation of the estimating methods used; and Volume II-Part 2, a more detailed discussion of the technical and cost features of the ten cases than is presented in Volume I.

Jan 1, 1976

By George S. Rice

"INTRODUCTION During the past 4 or 5 years the frequent occurrence of bumps in coal mines of the Cumberland field, in Harlan County, Ky., and Wise County, Va., has caused much apprehension among miners and mining officials of that region.These bumps have caused many deaths and injuries, and have been increasing in frequency. Eight men were killed and a number injured by bumps in the first 4 months of 1934. Their unpredictable occurrence and the usual absence of any preliminary warning tremors or sounds, such as ordinarily precede a large fall of roof, cause fear of other bumps and impair the morale of mine workers.Acknowledgments This report on bumps in coal mines of the Cumberland coal field of Kentucky and Virginia is based on an investigation made at the urgent request of .the Harlan County Coal Operators Association, through James F. Bryson, director of safety of the association, to the Director of the United States Bureau of Mines, following a series of disastrous bumps in. Harlan County, Ky., and Wise County, Va. The request was granted and the writer detailed to undertake the investigation, which was made in June 1934.The officials of certain operating companies in the Cumberland field gave every facility for examining the conditions accompanying bumps in their mines. The writer is most grateful to them for the courtesies shown; to J. F. Bryson, to J. F. Davies, district engineer, Safety Division, U. S. Bureau of Mines, who accompanied the writer throughout his trip to the vari¬ous mines and gave him much assistance and detailed information regarding the occurrence of bumps; and to Dr. David White for reviewing the geological descriptions,Definition of Bumps ""Bumps"" are phenomena comparatively rare in the coal fields of the United States and, for that matter, in the coal fields of the world, because for their occurrence certain exceptional natural conditions are required strong, massive strata of sandstone or conglomerate above the coal and a fairly strong floor, as will be described in detail later."

Jan 1, 1935

By Gerald T. Homce

Accidental contact of overhead electrical power lines by mobile equipment is a leading cause of occupational fatalities in the United States, accounting for 20% of on-the-job electrocutions. Overhead electrical power line proximity warning devices (PWDs) are intended to warn personnel if mobile equipment moves within some preselected minimum distance of an energized overhead electrical power line. Two commercially available PWDs were tested at the National Institute for Occupational Safety and Health?s (NIOSH) Pittsburgh Research Laboratory (PRL). The objective of the tests was to document performance capabilities and limitations for these PWDs by identifying factors that can influence their operation. The two PWDs evaluated in this research are the SIGALARM Model 210 marketed by Allied Safety Systems, LLC, and the ASE Model 2100 from Allied Safety Engineering. Both of these devices operate by measuring the electric field present around energized power lines. The PWDs were installed on a government-owned 22-st (20-mt) rough terrain crane. A purpose-built test site used for this research at PRL allowed operation of the crane near a variety of power line configurations operating at up to 25 kV. Most of the tests involved positioning the crane adjacent to one or more overhead power lines, adjusting sensitivities of the PWDs to alarm when the crane boom was approximately 20 ft (6.1 m) from the power lines, swinging the crane boom toward the lines under a wide variety of test conditions, and finally, for each unique set of test conditions, documenting the deviation from 20 ft (6.1 m) for actual alarm activation. Test results show that several factors can adversely affect PWD performance. PWD alarm accuracy generally deteriorated when operating with a boom position significantly different than that used for the device?s last sensitivity adjustment. Another factor that can affect PWD performance is configuration of the overhead power line(s) involved. Accuracy of alarm activa­tion distances was best for simple single-circuit installations, but degraded for multiple circuits on the same poles. This degradation was slightly greater for installations with different voltage levels and/or a combination of vertical and horizontal conductor arrangements. Performance also degraded for crane operation between two intersecting power line installations, especially for intersecting lines at different voltages. An additional aspect of power line configuration shown to influence PWD accuracy was phase sequence on the power line circuit(s). Specific phase con­ductor arrangements and combinations, particularly in multiple circuit installations, resulted in either improved or degraded accuracy.

Jan 1, 2008

By Wilson Blake

Increased application and interest in the use of microseismic monitoring to deal with ground control problems, Particularly those resulting in violent failures, has brought about the need for practical guidelines with respect to all phases of microseismic monitoring. This report presents the results of an 18-month effort to review the microseismic method and develop needed practical guidelines. Microseismic activity and properties of microseismic events are treated so that these parameters can be taken into account when developing monitoring equipment. Microseismic equipment is discussed to provide familiarization with the components of monitoring systems. Factors to be considered and procedures for developing a microseismic monitoring system are presented. Both physical and electrical considerations for the installation of a monitoring system are discussed in detail. The operation of a microseismic system including data analysis procedures is presented. Field examples to illustrate use of microseismic data in evaluating ground control problems are presented in a number of case histories.

Jan 1, 1982

This report presents the results of a study of mill tailings disposal practices and potential tailings dam stability problems. Recognizing the long period of time that would be required to develop the technology and practices necessary to significantly improve refuse disposal safety, the Bureau initiated this research effort as a first step in that development. Volume 1 includes a summary of conclusions and recommendations resulting from the overall research effort; discussions of disposal systems and methods, geology, seismicity, hydrology, and materials characteristics; evaluations of investigational techniques; discussions of usable interim generalized investigational, analytical and inspection procedures; discussion of general principles and presentation of a tailings technology manual outline; and discussion of needed future research am recommended programs.

Jan 1, 1974

By J. W. Adams

This report surveys the efforts of six contractors to the U.S. Bureau of Mines with regard to their electromagnetic noise measurement programs. What has been done, what is planned, and evaluations and recommendations are given for each contractor. The main observation is that to date there is not sufficient knowledge of electromagnetic interference in mine environments to design a reliable communication system. This knowledge should be available by the end of June 1972 if certain planned programs are completed successfully. A major effort of this report is to establish parameters to be measured, units to be used, and workable formats for data presentation. This is given in Appendix A. Some details concerning equipment, procedures, locations, and sample data are included in Appendix B.

Jan 1, 1971

By Daniel I. Carey

Current and potential dragline reclamation usage was evaluated for the U.S. coalfields based on data gathered and analyzed during field surveys, literature reviews and contacts with manufacturers. It was concluded that current mining plans have been adapted to federal and state strip mine and reclamation laws in ways which limit the potential for dragline reclamation systems at active mine sites. At abandoned conventional contour mine sites in steep-sloping areas such as central Appalachia, however, it was found that dragline reclamation systems have great potential application and may be the only practical solution to many reclamation problems. Alternative dragline systems were examined for restoring abandoned sites, and it was concluded that a tower excavator system offered superior characteristics and should be evaluated and developed under field conditions. A testing program was developed to provide a framework for the monitoring and analysis of cost, production and environmental data during a field demonstration of a tower excavator system.

Jan 1, 1981

By Robert L. Lagace

A prototype adaptive volume control for the loudspeaker output of mine trolley carrier phones was designed, built, and tested in the laboratory and in a mine. This volume control senses, and adapts to, the ambient acoustic noise environment in such a way as to produce a loud sound output under noisy conditions, and a quieter output under quiet conditions, thereby producing an understandable and unstartling volume level under all noise conditions. The design approach, prototype hardware, and test results are described, and the device is shown to be feasible for in-mine operations. The circuit design principles are easily applicable to currently available mina trolley carrier phones. Recommendations for practical improvements are included. An in-mine experiment to assess the practical feasibility and utility of the dedicated wire technique for overcoming poor trolley carrier phone system performance was designed, performed, and evaluated. The technique involves the use of a single, low-loss, properly terminated auxiliary wire, placed in the rail haulageway, which allows signals to naturally couple to and from the trolley wire/rail transmission line, and thereby significantly decrease the overall signal attenuation rate on the trolley wire/rail line. The in-mine dedicated wire experiment, results, and conclusions are described, and the technique is shown to be a valid and practical one for significantly Improving carrier phone system performance in mines. Guidelines for the installation and use of the dedicated wire are provided. Recommendations are made for obtaining further practical information on its performance and utility. A second in-mine experiment to assess the feasibility and utility of the low-impedance (low-Z) line technique for overcoming poor carrier phone signal transmission in mines was designed, performed and evaluated. The low-Z line technique involves the periodic connection of shunt capacitors between the trolley wire and the rail to artificially lower the line characteristic impedance. This causes the low impedance shunt loads encountered across the trolley wire/rail line to be less mismatched to the line, thereby reducing the overall attenuation of carrier phone signals. The results of in-mine experiments performed along unenergized and fully operational sections of trolley wire/rail line are described. The experiments were designed to measure line parameter such as inductance and capacitance per unit length, characteristic impedance, and propagation phase velocity, in addition to signal strength versus distance behavior under normal and low-Z line conditions. The low-Z line technique is shown to be valid, but not as practical as the dedicated wire technique which is recommended as the most favorable for most coal mine applications.

Jan 1, 1979

There has been a substantial increase in the use of rubber-tired front-end loaders in the mining industry in recent years. Concurrent with this increased usage, in the period of 1966 to 1970, there were at least 74 mining industry fatalities involving front-end loaders, or (on the average) in excess of one fatality per month. When the usage of front-end loaders by the construction industry and other industries, organizations, and agencies, such as the Government (i.e., Department of Defense), along with the uncounted numbers of serious, but non-fatal accidents, are included in the picture, the safety record for front-end loaders, of necessity, becomes a serious subject for study. There is an urgent need for attempts to be made to eliminate or reduce the number of safety hazards; to decrease the confusing diversity of controls designs found on present front-end loaders; to improve the maintenance and operating procedures; to formulate better personnel policies; to increase management and official awareness of the extent of the problem, in both industry and the Government; etc.; in order to decrease the number of accidents. Part of the problem may be traced to the fact that the operator of a front-end loader is frequently designated a "heavy equipment operator." This implies that he is automatically qualified to operate any model, of any manufacturer's, wheeled or tracked, front-end loader as well as many other types and classes of heavy equipment. Contrary to automotive practice, the complement of primary operating and emergency controls varies widely from model to model, as well as from manufacturer to manufacturer. Not only are certain controls present on one front-end loader model and absent on others, but there are significant differences in the modes of control operation, in the functions performed by superficially similar controls, in the location of the various controls, etc.

Jan 1, 1973

By H. E. Powell

The magnetic susceptibility, the geographical source, and associated minerals are given for 44 copper-, 26 lead-, and 19 zinc-bearing minerals. Of the 44 copper minerals/ all had a susceptibility of less than 15 X 10-6 cgs, and about 20 percent of them were diamagnetic. Of the 26 lead minerals, all had a susceptibility of less than 11 X 10-5 cgs, and almost half of them were diamagnetic. And, of the 19 zinc minerals, all except four had a susceptibility of less than 9 X 10-6 cgs, and about one-fourth of them were diamagnetic.

Jan 1, 1968