Search Documents

By R. Hogg, T. F. Dumm

"Abstract - With increasing interest in the physical cleaning of fine coal, there is a need for extension of the sink float analysis procedure to finer sizes. Problems arise, however, in ensuring complete dispersion of the particles in the heavy liquids. A procedure has been developed in which surfactants are used as dispersing agents, and solids concentration is minimized (using a simple formula to estimate the minimum weight needed for statistical reliability). Using centrifuges to increase separation rates and subsieve particle size analysis of the specific gravity fractions, a complete size specific gravity distribution can be obtained. Analyses have been performed on coal samples as fine as -10 µm.IntroductionTraditional gravity separation techniques such as jigging, heavy media and water-only cyclones, shaking tables, etc., have been used to remove impurities from coal ranging in size from about 15.cm (6 ln.) to about 150 µm (100 mesh). The coal washabilty or float-and sink technique ls a well-established procedure for determining the optimum extent to which a coal can be cleaned by such physical separation methods. Because of the desire to recover even finer coal fractions by gravity separation techniques, there is a need to extend the coal washabillty analysis into the ultrafine range. The purpose of this paper ls to describe some of the significant factors that influence fine particle specific gravity separation. Washability analyses have been performed on three ultrafine ( <10 µm) coal samples representing three general mining districts in Pennsylvania. Results of these analyses indicate that the washabillty technique can be successfully applied to ultrafine particles when proper care ls taken."

Jan 1, 1988

By W. S. Wright, A. W. Tolonen

"INTRODUCTION The Mount Andrew iron deposit on Kasaan Peninsula, Prince of Wales Island, Southeastern Alaska, was examined in August 1942 by an engineer 4/ of the Bureau of Mines accompanied by geologists 5/ of the Federal Geological Survey. From October 20 to 27, 1942, two engineers 6/ of the Bureau of Mines made a further preliminary examination and took three large samples of magnetite and magnetite-copper ore for metallurgical testing. During the stunner of 1942 an investigation of the Mount Andrew-Stevenson-Mamie area, including topographic and geologic mapping and a magnetic survey, was made by geologist 7/ the Federal Geologically Survey. On May 31 and June 2, 1943, two Bureau of Mines engineers 8/ conducted a preliminary examination in which special attention was directed to trails, camp, and drill sites. They were accompanied on May 31 by L. A. Warner of the Geological Survey.During the period from September 1943 through September 1944 Bureau of Mines engineers 9/ completed a thorough investigation which included trenching, core drilling, and sampling. A Federal Geological Survey representative 10/ examined all trenches and cores for geological data.LOCATION AND ACCESSIBILITYThe deposit is situated at latitude 55º 31' N. and longitude 132º 18' W. on the north side of Kasaan Bay on Prince of Wales Island, Southeastern Alaska. The general location is shown on figures 1 and 2. The deposit is 5 miles southwest of the village of Kasaan and by water, 27 miles northwest of Ketchikan; the main tunnel portal is 7/8 mile north of the Mount Andrew landing on Kassan Bay."

Nov 1, 1947

By T. M. Barczak

One of the primary goals of Bureau of Mines research is to reduce the cost of coal mining by improving the efficiency of longwall supports. One method of achieving this goal is the optimization of stress distribution within the support structure, resulting in a lower overall weight, more fully stressed shield. However, before stress optimization can be initiated, load conditions must be defined that cause maximum stress in the various support components. A finite-element model of a longwall shield was used to identify these critical load conditions. These load conditions were then evaluated in the Bureau&apos;s mine roof simulator (MRS) by instrumentation of a longwall shield and measurement of strains in each of the shield components. The critical (canopy-base contact) load conditions were identified that can cause structural failure at less than rated shield (hydraulic yield) capacity. Comparisons were made between full-contact and partial-contact load conditions. Other parameters investigated included the stiffness of the contact material, changes in shield geometry, rate of load application, and effects of horizontal constraint. Conclusions were drawn regarding the structural integrity of the major shield components and potential for stress optimization.

Jan 1, 1987

1. ACKERMAN, C. L. The Binary System Manganese-Zinc. Ztschr. Metall., vol. 19, 1927, p. 200. 2. ADKENASY, P., AND KLONOWSKY, S. Über die Manganatschmelze. Ztschr. Elektrochem., vol. 16, 1910, p. 107. 3. AKTIEBOLAGET FERROLEGERINGAR (assignees). Method for the Manufacture of Manganese Alloys Poor in Carbon or Silicon or Else Manganese. British Patent 163262, Apr. 28, 1921; U. S. Patent 1480267, Jan. 8, 1924. 4. Method of Producing Manganese or Manganese Alloys Poor in Carbon or Silicon. British Patent 174923, Jan. 25, 1922.

Jan 1, 1934

By Cleo G. Rall

The value of brine analyses in the study of petroleum-engineering problems was recognized early in the history of petroleum. The Bureau of Mines before 1928 had indicated in several reports.3/ ways in which analyses might be used. Because of the confusion resulting from attempts to correlate the work of different chemists using greatly varying methods of analysis and systems of computation and expression of results, a paper presenting the methods used by the Bureau of Mines was prepared and published in 1928. This system of determining the characteristic constituents of oil-field waters and of calculating and reporting results has been widely adopted by the petroleum industry. The earliest and most obvious use of water analyses is determination of the source of water infiltrating into petroleum and natural-gas wells. For this purpose it is necessary that an analysis of the connate water of the formation from which the oil is produced be available and that an analysis of the contaminated water be made. By comparing these analyses with those of connate waters from formations higher in the structure, the formation from which the infiltrating water comes may be identified.

Jan 1, 1953

By Robert S. Dalzell

Following the introduction of roof shields to the U.S. longwall mining scene in 1975, the number of shield faces (faces supported by shields) has increased steadily, and the occurrence of accidents associated with ground control inadequacies at longwall operations has shown a downward trend. However, ground control problems in longwall mining still exist. New mining systems, however efficient, have run afoul of roof control. Shield faces have suffered extended stoppages because of roof cavities. In this report, the Bureau of Mines addresses the problem of longwall roof control. The report presents a review of foreign remedial and strata replacement techniques for longwall faces and evaluates their potential for domestic application. The technology reviewed includes meshing, chemical rock stabilization, cribbing, strain-absorbent modules, inflatables, synthetic foam, and monolithic fills.

Jan 1, 1985

By V. E. Edlund

Pyrometallurgical studies by the Bureau of Mines demonstrated the feasibllity of sintering and smelting a low-grade flotation concentrate made by pilot-plant processing 10-percent manganese ore from the Maggie Canyon deposit, Mohave County, Ariz. Under optimum conditions 85 percent of the manganese in a flotation concentrate that assayed 36 percent manganese was recovered as standard ferromanganese. A blend of this flotation concentrate with high-grade dithionate pilot plant precipitate was similarly processed with a recovery of 90 percent of the manganese. Thorough mixing and pelletizing of the charge before treatment on the sinter hearth was necessary to produce a well agglomerated product by single pass sintering. Although satisfactory sinter was produced from a variety of material combinations, best results were obtained on a charge that contained 80 percent flotation concentrate and 20 percent return sinter fines. This combination was mixed with 6 percent coke, based on weight of concentrate; and 12 percent moisture. Sintering such a charge yielded a well agglomerated product containing over 80 percent coarse material, The results of standard crushing tests showed that the product was physically comparable to iron ore sinters and manganese nodules.

Jan 1, 1962

By Robert S. Sanford

Intensive investigations of domestic manganese deposits were conducted by the Bureau of Mines and the Geological Survey during the earlier part of the war minerals investigations when there was doubt that the quantity of manganese needed to produce the greatly increased tonnage of steel demanded for war supplies could&apos; to obtained from its customary sources. Domestic deposits of ores that contain sufficient manganese for direct production of ferromanganese essential in steel Manufacture are generally small, and the bulk of the supply is imported. One of the few large deposits of low-grade manganese ore known in the United States is in the Artillery Peale district in southern Mohave County, Ariz. Manganiforous sediments underlie a very large area. Several large groups of claims, covering the most of the manganese-bearing ground, wore assembled in 1929 and 1930. The greater part of this area was leased by the M. A. Hanna Co. in 1937. Investigations by engineers and geologists for this company revealed that the average content of manganese is very low; but that the Maggio Canyon area, about 180 acres, contains higher-grade material. The company put down 28 vertical diamond-drill holds to explore this ground, under the direction of B. N. Wobbor, geologist.

Jan 1, 1948

Table 1.-Salient statistics of carbon black produced from natural gas and liquid hydrocarbons in the United States [ ]

Jan 1, 1967

By Jr. Hazen

This report documents 653 sets of sample data involving 78,366 assays obtained from past exploration for various minerals and metals. Most of these data have been taken from published reports describing exploration projects, conducted jointly by the Bureau of Mines and the Geological Survey, for the Strategic Minerals Program from 1940 through 1949. Means and standard deviations have been computed for the exploration assay data and have been plotted on graphs for 22 minerals and metals. A mathematical model, based on the binomial distribution, has been developed to explain the configuration of the plots of the exploration means and standard deviations. The two statistics, mean and standard deviation, which describe assay data, have been used for simulating probability models. These probability models then have been combined with the binomial model of the exploration assays and related to the sequential decision process associated with exploration drilling for mineral deposits. These probability regions can be used to form the basis for sequentially predicting the probable range of the average grade of mineral or metal that may be expected as an exploration drilling program is continued after the initial discovery of mineralization has been made.

Jan 1, 1966

By E. L. Singleton

The electrochemical reduction of aluminum chloride to aluminum was investigated in a closed, two-compartment cell utilizing a molten chloride electrolyte. The externally heated cell was divided into a reduction compartment and a combination AICl3 feed and metal removal compartment. Aluminum was deposited at 700° C on a molten aluminum catbode from a KCI-NaCI-AICI3 electrolyte. The AICl3 content of the electrolyte was replenished by either vapor or solid additions. The chlorine evolved was collected and measured to give a quantitative evaluation of AICl3 reduction. The effects of anode and cathode current densities and AIC13 concentration on anode current efficiencies were studiedo A range of 64 to 84 percent anode current efficiency was obtained with the 25-pound electrolyte capacity cell and related auxiliary equipment.

Jan 1, 1968

By W. L. Acherman

Molybdenum, tungsten, and vanadium were found by the Bureau of Mines to possess generally superior chemical and galvanic corrosion properties in many aqueous corrosive media at temperatures up to the boiling point. The corrosion resistance of vanadium in certain solutions was further improved by alloying it with such metals as columbium, tantalum, and titanium. was susceptible to a type of crevice corrosion in mercuric chloride solutions, but no other instances of crevice corrosion were encountered. With few exceptions, molybdenum, tungsten, and vanadium were not adversely affected when coupled with dissimilar metals in galvanic corrosion experiments; in some cases one or both members of a couple were protected by contact. When exposed to aqueous ammonia spray at 60° C, all three metals were attacked, but they were moderately resistant in spray environments of substitute ocean water and ammonium dihydrogen phosphate.

Jan 1, 1966

This report provides the results of an industrial engineering study that assessed the safety and efficiency of underground ore handling in U.S. metal mines. One of the primary findings of the study was the improvement needed in controlling muck size in the ore handling stream. Oversize ore causes much additional labor, creating work stoppages and is a principal cause of accidents in metal mines. This report includes data on block caving, back cut and fill room and pillar, shrinkage stoping, and sublevel stoping.

Jan 1, 1974

By H. N. Dunning

A comprehensive research program designed to aid development of new and improved methods for more complete production of petroleum from partly depleted reservoirs is being conducted at the Bureau of Mines Petroleum Experiment Station, Bartlesville, Okla. Water flooding has accounted for much of the petroleum produced by secondary-recovery methods; however, a considerable portion of the crude oil commonly remains in place after water flooding has been terminated. In recent years the possibility of increasing the efficiency of water flooding by using surface-active additives has received wide attention. In general, the results of laboratory research have shown that use of detergents as water-flooding additives will reduce the residual petroleum in porous media (1).3/ Some less extensive field tests have supported this conclusion but have not been entirely conclusive (2). Later studies (3, 4) have given conflicting evidence as to the relative worth of detergent additives for water floods in water-wet (hydrophilic) or oil-wet (hydrophobic or lipophilic) reservoir materials. The results of these studies emphasize the need for a more complete understanding of the fundamental principles involved in displacing petroleum from reservoir surfaces by injected fluids. Accordingly, a comprehensive research program was initiated to investigate the practical and fundamental aspects of detergency in petroleum production.

Jan 1, 1953

By John M. Dale

Sulfur is a plentiful, low cost, unique material whose physical properties can be altered and employed in structural applications. This program was undertaken to develop an optimum sulfur based formulation for use as a coating to both seal and support mine walls. The initial effort in the program was devoted to a laboratory study of the physical and mechanical properties of a variety of sulfur base coatings that were specifically formulated for this application. Concurrent with formulation development, laboratory equipment and techniques were developed for spray applying the sulfur based coatings to the ceiling and walls of a structure that simulated the interior of a mine. Much of the formulation work was guided by the experiences encountered when attempting to spray the formulations overhead. One hundred parts of sulfur modified with 10 parts of talc, 3 parts of milled glass fiber, and 2 parts of dicyclopentadiene was found to be a fire retarded, low odor, low eye irritation, sprayable formulation for sealing and strengthening mini, walls. An invention disclosure on this formulation was submitted to the Bureau of Mines and a patent application was filed. Various mineral samples were obtained and adhesive strengths of the formulation to these samples in both the wet and dry state were measured. With the development of an attractive sulfur based coating material, attention was directed to the design, fabrication, and testing of a portable spray application unit so that coatings might be applied in the field to various rock surfaces and earth formations for further evaluation. The unit was fabricated in the Southwest Research Institute shop. Once operational, the unit&apos;s capabilities were field tested and demonstrated at three separate locations. Upon completion of the field testing, the unit was shipped to the Spokane Mining Research Center where Bureau personnel were instructed in the use of the unit.

Jan 1, 1972

By D. B. Taliaferro

[Recovery of core specimens from subsurface formations and their subsequent analysis are important aids in efficient development and operation of oil and gas fields. Core specimens first were obtained mainly for the geologic information they revealed; now they are analyzed to determine many of the physical characteristics and conditions of tae subsurface formations as well. Cores recovered from the producing formations may be analyzed for porosity, permeability, oil content, "connate" water content, and other physical and chemical properties of the formation, all to the end of furnishing enough data for making reliable estimates of the quantity and availability of oil and gas within a reservoir and in devising, efficient means for their withdrawal.]

Jan 1, 1939

By Thomas A. Davidson

The Bureau of Mines Helium Field Operations has developed a simple and accurate method for calculating the viscosity of gas mixtures. Only the composition of the mixture and the molecular weights and viscosities of the pure components in the mixture are required. The momentum fraction of a mixture is calculated from the composition. The fluidity is calculated as a quadratic function of the momentum fractions. The efficiency factor for transfer of momentum in collisions between bodies of different masses is derived and used with one empirical constant. The viscosity is the reciprocal of the fluidity. Results of the method are compared with 752 reported viscosities for 40 dilute binary systems at temperatures from -78 to 276.9°C. Using this method the average absolute deviation is 1.29%, the root-mean-square deviation is 1.99%, and the average deviation is -0.84%.

Jan 1, 2010

By J. O. Lewis, Carl H. Beal

The material for this paper was collected for the most part by C. H. Beal during the years 1916, 1917, and 1918. Many of the conclusions reached in regard to the life of oil wells have already been published by the Bureau of Mines 1 but those presented in this paper deal particularly with the theoretical aspects of oil production. The report discusses some of the fundamental factors governing oil production, taking up first the conditions affecting the. amount of oil in the oil sand, then those factors that control the rate of production of oil wells, and then discusses several related problems, most of which deal particularly with the effect of the production of one well on that of another.

Jan 1, 1921

By Scott W. Hazen

This report describes the design, analysis, and results of a special experimental mine-sampling project conducted as part of the Bureau of Mines continuing program on sample-methods research. The experimental project was conducted at the Bureau?s Denver Mining Research Center and at the Climax molybdenum mine within the framework of a cooperative research agreement between the Bureau and Climax Molybdenum Co., Division of American Metals-Climax, Inc. The primary objective of the project was to investigate the interrelation-ship between sample volume, number of samples, the standard deviation of an assay distribution, and the precision required for an estimate of grade of ore, and to develop this interrelationship into a relatively simple method of application for use in mine sampling.

Jan 1, 1962

Consumption and intensity of use trends for twelve metals, by industrial end use, were estimated for 1972 through 198Z. The trends were then forecast through 1993 using standard statistical methods. The intensity of use measure selected is the quantity of metal consumed per constant dollar output of a specific industrial sector. The metals studied were aluminum, chromium, cobalt, copper, lead, manganese, nickel, the platinum-group metals, tin, titanium, tungsten, and zinc. Average annual growth rates for the following four of the twelve metal increased from 1972-82 as follows: aluminum, 1.00 percent; platinum-group metals (consisting of platinum, palladium, and iridium), 8.83 percent; titanium, 7.82 percent; and tungsten, 6.09 percent. Consumption. for the remaining eight metals decreased at average annual rates ranging from 0.58 percent (copper) to 5.37 percent (manganese).

Jan 1, 1986