Search Documents

By Margaret R. Egan

A study of the combustion emission products of rigid ventilation ducting was completed by the U.S. Bureau of Mines. The ducting was composed of fiberglass-reinforced polyester resin. Four properties of the ducting were evaluated: (1) propensity to ignite, (2) smoke characteristics, (3) gas emissions, and (4) heat release. Particle sizes, obscuration, optical densities, and production constants for gas and smoke were also calculated. These results provide comprehensive data about the emission products, detectability, and relative hazards of fiberglass-reinforced plastic ducting and other mine combustibles under realistic fire conditions.

Jan 1, 1990

By Je M. Oh

The U.S. Bureau of Mines is conducting research on the oxidation resistance and structural stability of Fe-(0-8)Cr-(0-16)Ni-(0-16)Mn-3.5Si-lAl alloys as potential substitutes for high-Cr stainless steels. Oxidation tests were conducted in air over the temperature range of 6000 to 9000 C for up to 1,000 h. Microstructures were analyzed at room temperature after hot rolling. The oxidation properties and the structural stability were found to be greatly affected by the Cr and Mn levels. Although substitution of Mn for Ni increased the oxidation rate, the Mn helped to stabilize the austenitic microstructure. Decreasing the Cr content or increasing the Mn content produced higher oxidation rates and earlier oxide spalling. In this study, reaction kinetics, oxide morphologies, and microstructure of the alloys were investigated using scanning electron microscopy, energy dispersive X-ray analysis, X-ray diffraction, and electron microprobe analysis.

Jan 1, 1989

By R. L. Crosby

Microscopical and X-ray diffraction techniques were used to identify two intermediate phases in that part of the solid region of the magnesium-cerium system between and Mg3Ce. Previous literature had reported only one intermediate phase for this region, 1)12t chemical analysis determined the approximate composition of the two compounds to be Mg23Ce2 and Mg17Ce2. The range in composition of the two intermediate phases was found to be limited to less than 0.3 atomic percent cerium. The study did not determine the crystal structure of Mg17Ce2, but that of Mg23Ce2 is tetragonal with a = 10.33 A and c = 19.51 A.

Jan 1, 1966

By E. J. Gleim

[THE ORGANIC act under which Federal Bureau of Mines was established provided for the investigation of the safe use of electricity in mines. Each Congress appropriates funds for conducting this investigation. As part of this investigation, electrical apparatus used in mines is studied to determine if its operation and use might introduce a hazard. From this study, certain safety standards have been developed. These standards, established with the aid of both the manufacturer and user of such apparatus, are published in schedules, and apparatus that complies with the requirements set forth these schedules is classified as "permissible." This term is defined to designate apparatus as "completely assembled and conforming in every respect with the design formally approved by the Bureau of Mines." In the judgment of the Bureau, the manufacturers of such apparatus have adhered to certain minimum standards of safety in supplying a product that when properly used and maintained is safe for operation in mines where flammable gas or coal dust may accumulate. This work of the Bureau of Mines for increasing safety does not make it obligatory for manufacturers of mine equipment to produce only that of permissible classification. Before the effective date of the Federal Mine Safety Code,5 the Bureau sought to promote safety by recommending that mine operators install permissible equipment in gassy mines as a preventive measure against gas and dust explosions initiated by electrical equipment. For some years, the mining laws of several States have prescribed the conditions under which permissible equipment must be used. The Federal Mine Safety Code requires that ?all new electric face equipment and replacements of equipment purchased for mines where nonpermissible equipment is now being used shall be of a permissible type approved by the United States Bureau of Mines,]

Jan 1, 1955

"IntroductionThe combined library facilities of the five universities in the Generic Technology Center for Respirable Dust, The Pennsylvania State University, West Virginia University, University of Minnesota, Massachusetts Institute of Technology, and Michigan Technological University, represent one of the most extensive and comprehensive collections of information on respirable dust research which is available in the United States. The Center encompasses two major medical schools, the Milton S. Hershey Medical Center at The Pennsylvania State University and .West Virginia University Hospital at West Virginia University, and includes national and international experts from such diverse disciplines as geology, geomechanics, mining engineering, mineral processing, electrical engineering, industrial engineering, mechanical engineering, material science, physics and several areas of medicine. In order to maximize achievements in research and facilitate early results application in the private industry, university, government and public sectors, a geographically dispersed Reference Center on Respirable Dust has been established at each of the affiliated universities. This network serves to encourage unity between the universities in the Center and coordination and communication with other entities who benefit from their research.Description of the Reference CenterIn this light, the goal of the Reference Center network is to identify at what location Information is available and to provide a means for others to access this information. It is especially necessary to have both ease of input and maximum retrieval capabilities available to all the research personnel in the Reference Center. At the same time, the service provided to the inquiring public must be complete and cost-effective. The Center's approach to realizing this goal incorporates advances in computerized and electronic searching of individual library holdings and the networking of major library and commercial search systems.The Reference Center uses the following means to achieve this goal. At each participating university, a hard copy collection ls maintained of the current respirable dust research in progress by that institution's personnel. Also, available. at each university ls a review of their past and present research on respirable dust. At each participating university a hard copy collection of annual status reports and of all publications produced by Center personnel for symposiums, national and international conferences ls maintained. A key word computer search capability ls available to participating universities. This computer search, by title, author and location, allows researchers to determine at which facility information is available, thus avoiding the tremendous expense and effort of housing all the information on respirable dust research under one roof. The Reference Center has access, through The Pennsylvania State University Libraries system and the libraries of other institutions, to a large number of data bases such as MEDLINE at the National Library of Medicine,"

Aug 31, 1989

By M. J. Gavin

Within the past three years numerous inquiries for information on oil shale have been received by the Bureau of Manes. These inquiries have been increasing to such an extent that it has seemed advisable to issue a short paper prior to the publication of a bulletin on the subject, giving a, general discussion of the subject and a comprehensive list of references, so that those interested in the details of obtaining oil from shale can find additional information without much difficulty. Some of those who desire information are interested only in a general discussion of the subject, or are not in a position to refer to books and' articles describing the industry. The material for this paper is largely derived from published information on oil shale. Much of the information is obtained-from the books and articles mentioned in the list of references, and has been compiled with the intent of furnishing information to those not interested in all the details.

Jan 1, 1921

By Barry L. Warner

This program involves the evaluation of means for suppressing fires on underground coal mine conveyor belts. Full scale conveyor belt fire tests were conducted to determine the requirements of automatically actuated water sprinkler, high expansion foam, and multi-purpose dry powder extinguishing systems, and of various fire detection devices, necessary to adequately protect underground belt heads. The program included the development of a suitable MI scale conveyor belt test fire, conducting of fire tests in which extinguishing and detection systems and equipment were evaluated, and testing to evaluate the effects of the coal mine environment on detection equipment. Preliminary testing conducted to develop a suitable test fire revealed that fire can propagate on some conveyor belting classified as fire-resistant. New fire-resistant PVC and new non-fire resistant rubber belts were used in the full scale fire tests. These tests indicated that a single branch line sprinkler system with relatively low water pressure provides adequate belt head protection. High expansion foam and multi-"purpose dry powder extinguishing systems as presently specified by regulation were found to be suitable for belt head protection, although care is required with powder systems to assure adequate distribution. Thermal type detection devices were found to be most practical for conveyor belt protection, with combustion products and optical detection methods having serious disadvantages.

Jan 1, 1974

By Thomas A. Morgan

The distribution of stress adjacent to each of 25 mine openings was determined by the borehole stress-relief method in the FMC Corp. Westvaco trona mine at Westvaco, Wyo. The purpose of the stress determinations was twofold: First, to study the effect on these distributions of various factors such as opening shape, stress level, and loading history; and second, to estimate the distribution of stresses adjacent to extensive high-extraction (85 to 100 percent) areas. Stress distributions in areas of low average stress correspond closely to the theoretical distributions based on elastic theory. However, in areas of high average stress, the stress distributions are of a type associated with plastic failure. The stresses adjacent to a mined-out area supported by remnant pillars were significantly higher than the stresses adjacent to another area in which the remnant pillars were removed.

Jan 1, 1965

By Edward L. Wilson

A general computer program is given for the linear elastic static analysis of complex structural systems. These elements have special advantages for the analysis of massive underground structures such as mine structures and above ground structures such as arch dams. New finite elements are developed which are useful in the analysis of two and three dimensional solids. Examples are given which illustrate the accuracy of the elements. A description on the use of the program and a FORTRAN IV listing are given in the Appendices.

Jan 1, 1971

Table 1.-Aden: Production of mineral commodities [ ]

Jan 1, 1967

By Guy B. Taylor, Horace C. Porter, E. C. White

When the Federal investigation of coal - dust explosions in mines was begun in 1908 , following a series of mine explosion disasters in 1907 , mining men generally questioned whether coal dust in air is explosive unless " gas " or methane is present , though perhaps in small amounts not detectable by a safety lamp . The experimental tests beginning in 1909 at the Pittsburgh testing gallery, and after 1911 , at the Experimental mine , demonstrated to the mining public the explosibility of coal dust in itself . There followed much controversy , both among practical mining men and scientists , as to whether the coal-dust particles uni te directly with the oxygen of the air, or whether gas is instantaneously distilled from the dust prior to explosive combustion , the gas enveloping each particle and propagating the flame from one to another . In considering methods of preventing explosions , this question made no difference for practical purposes , but it did have bearing in determining the relative inflammability of dusts of different coals . This led to the experiments by Guy B. Taylor and Horace C. Porter , on the momentary heating of the inflammable coal dusts , reported in this paper . Meanwhile , experiments on the inflammability of coal dust conducted in the Experimental mine , under my direction , and in the laboratory by J. C. W. Frazer and later by J. K. Clement and J. N. Lawrence , showed that different kinds of coal dust differ markedly in inflammability , thus confirming experiments made by Messrs . Taffanel and Durr at the Lievin Testing Station , France , and by various investigators in Great Britain . Both the French and British investigators concluded that their experiments demonstrated the distillation of volatile matter preceding inflammation .

Jan 1, 1922

By H. R. Shell

To obtain a better understanding of the crystallization of fluoride containing amphiboles from melts, an investigation of the range of stability between fluoramphi-boles and other minerals was conducted by the Bureau of Mines. This study has shown that the stability of fluoramphiboles is strongly influenced by both fluoride concentration and isomorphic replacement. Over 150 reactions were made with different compositions and reaction conditions. substitutions attempted and the phases that formed when the composition was crystallized by cooling from the melt are discussed. The attainment of equilibrium in these multicomponent systems is not claimed. Many ions that would be expected to enter the amphibole structure instead resulted in crystallization of phases other than amphibole. Those compositions that resulted in a high yield of acicular fluoramphibole by crystallization from the melts are shown in table 2. The fluoramphiboles obtained from melts typically had an acicular crystal habit and a hardness of 6 to 7 on the Mohs' scale. Although many had relatively high length to cross section ratios, none were fibrous; it was concluded that the possibility of synthesizing a fibrous fluoramphibole from a melt was low. However, many compositions can be crystallized into a tough, hard, impact-resistant mass of interlocking acicular crystals.

Jan 1, 1958

By Kenneth M. Maas

The Bureau of Mines inventoried the land availability for mineral exploration and development in northern Alaska and compared this land with known mineral terranes and mineral deposits, to quantify the potential for favorable location of mining claims for metalliferous mineral deposits. This report includes thirty-three 1:500,000-scale maps that depict land availability, and the accompanying text and tables relate availability acreage to areas of favorable mineral terranes. Three categories of land availability and ownership are identified, along with 12 subcategories of land status. Available land comprises approximately 14.5 million acres or 16% of the 90.3-million-acre study area; land available with restrictions accounts for 7.5 million acres or 8%; and unavailable land encompasses 68.3 million acres or 76%. Mineral terranes underlie 37.8 million acres or 42% of the study area; 5.3 million acres or 14% are available for mineral location, 2.8 million acres or 7% are available with restrictions, and 29.7 million acres or 79% are unavailable. There are 500 known mineral deposits or occurrences within the study area. This includes 271 lode deposits, of which 171 lie within a recognized mineral terrane and 55 are on available land. The remaining 229 are placer deposits.

Jan 1, 1987

By Henry C. Meeves

The Bureau of Mines investigated the silver production potential of the Leadville (California) mining district, Lake County, Colo., in 1966-67. The mining history of the district, the ground conditions encountered in mining, and the mine-support methods used are reviewed. The drainage problem is discussed in detail. An initial objective was to establish the existence of potential silver resources minable by low-cost open-pit methods, particularly in the silver-bearing manganese halos surrounding the major deposits. The report concludes that under present conditions, development of the deposits in the area is not economically feasible; however, a pioneer rotary noncore drilling program demonstrated that this type of exploration is technically feasible. Potential reserves of silver and associated metals are estimated. Possible mining methods for recovery of the reserves are discussed. Future production possibilities from the various subareas of the district are analysed, considering optimum operating size. Consolidation of small individual holdings for unit operation is recommended. Type of operation, amount of rehabilitation, size and type of concentrating plants required, drainage and other mining problems, and metal price trends are discussed as they bear on economic feasibility of development.

Jan 1, 1970

By Stephen M. Jasinski

The development and industry adaptation of advanced technologies have led to many important uses for bismuth and its compounds. Bismuth-base alloys are essential for manufacturing jet engine turbine blades, lenses, and various safety devices, such as fire-protection sprinklers. The addition of bismuth to iron, steel, and aluminum imparts properties to these metals that makes them useful in diversified applications. Bismuth is also used widely in medicine, pigments, and electronics. The United States relies heavily upon imports from South America and Europe to meet its demand for bismuth, which is recovered chiefly as a byproduct of lead processing.

Jan 1, 1992

By Robert F. Pettit

This paper on methods and costs of mining and milling iron ore at the Iron Mountain mine of Ozark Ore Co., St, Francois County, Mo., is one of a series of Bureau of Mines reports on methods, practices, and costs of mining and milling throughout the United States. The Iron Mountain operation is notable for its successful transition from open-pit to underground mining, for use underground of large earth-moving equipment, and for development of a multilevel room-and-pillar mining method. Milling methods also have undergone transitions - from hand sorting and log washing in the early days to gravity concentration. Milling ultimately may include flotation to recover additional iron from products now discarded as tailing,

Jan 1, 1957

By J. E. Shelton

Flotation tests are described on samples of two lowgrade nickeliferous ores of Oregon and Washington. The sample from the Congress mine, Ferry County, Wash., contained 1.2 percent Ni, occurring chiefly as millerite. The sample from the Shamrock mine, Jackson County, Oreg., contained 2.20 percent Ni and 0.78 percent Cu occurring chiefly as pentlandite, nickeliferous pyrrhotite, and chalcopyrite. The millerite in the Congress ore was concentrated by flotatioin with aulfydric collectors in a series of locked tests to recover 73 percent of the nickel as a 7 percent bulk concentrate. By successively regrinding and floating the bulk concentrate, it was further concentrated to 12.4 percent Ni at a recovery of 59 percent and 21.8 percent Ni at a recovery of 50 percent. Attempts at selective concentration of the copper-nickel Shamrock ore were only partly successful because of the intimate association of pentlandite and chalcopyrite. The nickel concentrate, which contained 86 percent of the nickel, had an analysis of 4.42 percent Ni and 1.03 percent Cu. The copper concentrate had an analysis of 18.8 percent Cu and 1.96 percent Ni and contained 48.5 percent of the copper. A bulk sulfide concentrate contained 92 percent of the copper and 01 per¬cent of the nickel and had an analysis of 4.17 percent Ni and 1.63 percent Cu.

Jan 1, 1956

By Henry H. Ginsberg

The Federal Bureau of Mines made pilot plant investigations of the process requirements necessary to produce heavy fuel oil by the liquid-phase hydrogenation of bituminous coal. The investigation was carried out in three separate series of experiments. The first series studied the effect of temperature and contact time on product distribution at 3,500 p.s.i.g. and 420° to 480° C. in the presence of 0.1 wt.-pct../ stannous sulfide plus 0.05 wt.-pct. iodoform based on gross coal. As a result of increased contact times and temperatures, the conversion-6/ and yield of hydrocarbon gas increased, the viscosity of product oil decreased, and elimination of oxygen, nitrogen, and sulfur from coal increased. The yield of oil did not indicate any definite trend with changes in temperature and contact time. The yield of oil ranged from 76 to 85 pct. for Pittsburgh coal and from 60 to 85 pct. for Rock Springs coal. Asphaltenes in the product oil ranged from 17 to 38 pct. of the total oil for Pittsburgh coal and from 12 to 22 pct. for Rock Springs coal. Fuel oils meeting Bunker C or American Society for Testing Materials (ASTM) Grade 6 specifications were produced with Rock Springs coal at 0.2- to 1.0-hr. contact time and 440° to 480° C. and with Pittsburgh coal at 0.3- to 1.0-hr. contact time and 420° to 460° C. In the second series of experiments tin, nickel, iron, and zinc were evaluated as catalysts for the hydrogenation of Rock Springs coal to heavy fuel oil at 3,500 p.s.i.g. and 460° C. Using the apparent conversion of coal as criterion of catalyst activity, at a contact time of 0.45 hr. tin was the most effective catalyst; nickel and iron were nearly as effective, but the use of zinc resulted in much lower conversion. When the contact time was increased to 0.80 hr., the apparent conversion of coal was essentially the same for each of the catalysts. When the yield of oil boiling below 3550 C. was used as criterion of catalyst activity, at 0.45 hr. the order of activity was tin, iron, nickel, and zinc; at 0.80 hr. tin was far superior and the others were essentially equal. The product oils contained from 8 to 20 pct. asphaltenes.

Jan 1, 1960

By J. M. Mutmansky, C. Lee

"This paper outlines some of the work associated with a research study into the relationship between the characteristics of coal mine dust and the incidence of coal workers' pneumoconiosis (CWP). The project involves study of the chemical, mineralogical, and morphological characteristics of the dust. Early stages of the study have dealt primarily with the size analysis and elemental composition of airborne dust in continuous miner sections. This paper outlines the procedures and findings of the elemental analysis portion of the study.Most of the previous elemental analyses of coal were made available in the quest for information on the combustibility of coal dust or on causal agents and prevalence of CWP. However, no extensive studies have been performed to date, primarily due to the limitations of the analytical methods. A review of the analytical methods for elemental characterization of coal and coal dust particles is presented. TI1e comparisons are made based on the sample mass required, the sample preparation required, the destructivity of the test, and the capability of providing an easy multi-element analysis. The reasons for selecting the proton-induced x-ray emission spectroscopy (PIXE) method are outlined.The PIXE method was applied to both the airborne coal mine dust and channel samples collected from seven continuous miner sections in six different mines. Channel samples of the coal, roof and floor were collected and analyzed. Airborne dust sampling was performed using multi-stage cascade impactors and permissible 2.0 I/min pumps. Sampler locations were fixed in the sections with respect to the continuous miner and roof bolter or with respect to the intake and return airways. Sampling times varied from 45 minutes to 6 hours, depending on the dust concentration.The statistical analysis of the resulting elemental data is presented. Of particular importance are the analyses of the variation of elemental composition with size and the variation in elemental composition over the working section. One interesting finding is outlined showing the multivariate statistical analysis of the trace elements and its implications in the identification of the dust sources. The paper concludes with an analysis of the ramifications of the elemental data to related medical studies."

Mar 1, 1989

By R. E. Mussier

This investigation was made to study new methods to prepare high-purity yttrium metal, Various methods were used to prepare pure intermediate compounds, primarily chlorides, bromides, and iodides, which were subsequently reduced to metal. The process found most suitable for the preparation of pure anhydrous yttrium chloride involved thermal dehydration of a mixture of hydrated yttrium chloride and ammonium chloride while under vacuum. Yttrium bromide and iodide were prepared most effectively by the direct halogenation of yttrim carbide. Yttrim carbide was obtained by reacting and melting yttrium oxide-carbon mixtures in a carbon-arc furnace. Yttrium halides were purified by vacuum distillation and reduced by alkali or alkaline-earth metals. Lithium and sodium proved to be the best reductants from the standpoint of yield (>95 pct) and purity (>99.8 pct) of the yttrium. The product of the reduction step was sponge metal, which was consolidated readily by conventional cold-mold, arc-melting procedure. The purest yttrium obtained in laboratory scale work was prepared by sodium reduction of yttrium chloride and contained only 125 pp oxygen; other impurities did not exceed 1,000 ppm. In larger scale tests yttrium containing only 800 to 1,000 ppm total impurities was obtained by lithium reduction of yttrium chloride. The tensile properties of high-purity yttrium were determined. Mechanical tests showed that yttrium can be forged, extruded, rolled, spot welded, and deep drawn.

Jan 1, 1963