Search Documents

By C. A. Taylor, C. E. Munroe

"In blasting the explosion of the high explosives charge is initiated by means of a detonator. Consequently the successful operation of the whole system is, ab initio dependent upon the suitability and efficiency of the detonator used. A considerable number of methods for testing the efficiency of detonators have been devised. In a previous publication*** of the Bureau of Mines many of these were discussed after having been classified as direct and indirect methods.In 1910, W. O, Snelling, then explosives chemist of the Bureau, devised a direct method which depends on the extent to which a hard brittle material of uniform granulation, such as quartz sand, is pulverized by the explosion of the detonator when imbedded in it, and, as a container in which to carry out the tests, he devised the vessel known as the Bureau of Mines sand-test bomb No. 1. A brief mention of his work was made in a paper presented to the Engineers' Society of Western Pennsylvania.****Later Storm and Cope made a very extended investigation of this method using sand-test bomb No, 1. Their paper***** contains a detailed, illustrated, description of sand-test bomb No. 1, with precise specifications of the sand and a minute account of the technique followed, together with a discussion of the data they obtained from the tests in this bomb of 112 detonators representing each of the grades from We, 3 to No. 10, inclusive. The average of results obtained by them are set forth in the following table."

Dec 1, 1923

By Robert H. Peters

Groundfall accidents have been the leading cause of fatalities in the underground coal mining industry for many years. Statistics from the Mine Safety and Health Administration (MSHA) indicate that approximately half of the victims of these fatal accidents were in an area where no devices had been installed to support the mine roof. This report was prepared by the U.S. Bureau of Mines to provide guidance to operators of underground mines concerning the use of techniques that may help to keep miners from going under unsupported mine roof. The report is divided into two major sections. The first section reviews the findings from several areas of empirical research pertaining to strategies for convincing employees to avoid unsafe acts and/or adopt self-protective behaviors. The strategies are (1) incentives and feedback, (2) disciplinary actions, (3) training (primarily fear communications and behavioral modeling), and (4) nondirective techniques. This literature review has a broad focus and should be helpful in making decisions about how to encourage a wide variety of types of self-protective behaviors. The second major section of the report presents an analysis of each strategy's potential for keeping miners away from unsupported roof.

Jan 1, 1991

By Wesley T. Holmes

In this final stage of a three-part investigation of the smelting of titania-bearing iron materials, the Bureau of Mines conducted semicontinuous smelting tests in a laboratory electric arc furnace on four concentrates and one are. The objective was to substantiate the significance of liquidus temperature measurements in predicting satisfactory slag compositions in electric furnace smelting of titaniferous magnetites to produce pig iron. Previously obtained liquidus temperature data were used in determining flux requirements. Self-fluxing pellets of either ore or concentrate plus fluxes and reductants were made to produce pig iron and slags containing 0.2 to 0.6 percent titanium. Individual constituents of the slags generally agreed within 5 percent with the value of the corresponding constituent of target composition. Liquidus temperature of furnace slags generally agreed within 50° C of the value obtained from corresponding nominal synthetic slag. The results of the three phases of the investigation may serve as guide-lines for determining flux requirements in smelting a wide variety of titaniferous magnetites and other titania and iron-bearing materials.

Jan 1, 1969

By M. H. Kline

The Great Gossan Lead in Carroll County, Va., is one of the largest undeveloped sulfide ore bodies known in the eastern United States. It extends for 16.7 miles along the western slope of the Blue Ridge Mountains (fig. 1). The various known segments of the deposit, extending from the southwest end to the northeast, are: The Great Outburst or Iron Ridge segment, Chestnut Creek, Copperas Hill, Sarah Ellen, Wild Cat, Cranberry, Dalton Hill and offset segment to the south of the Cranberry, Little Reed Island, Little Vine, and the Betty Baker at the northeast end. All of these segments have been explored or mined to various extents in the past for the iron gossan and secondary copper ore. The Great Outburst or Iron Ridge segment is now being mined by the General Chemical Division of the Allied Chemical & Dye Corp. for the sulfur and iron content of the primary ore. These deposits are becoming increasingly of Interest as a. large potential source of iron and sulfur owing to their proximity to Birmingham, where the burned cinder sells at a premium, and to the acid markets of the region.

Jan 1, 1949

By R. E. Heithecker

Zwolle oil field of Sabine Parish, La., is different from most oil producing areas of the State in that the oil is obtained from marl and chalk-rock formations. The thickness of the reservoir rocks averages 500 feet; but production is not continuous throughout this thickness, as the oil apparently is localized in vertical and nearly vertical solution cavities and channelways or in porous zones of limited horizontal extent. The nature of the oil accumulation has caused two outstanding peculiarities of the field: (1) About 60 percent of the tests drilled were dry holes and (2) there were many instances of well interference. Commercial production was discovered in November 1928, after 17 years of prospecting in and around the present limits of the area now developed which has a length of about 22 miles and a maximum width of 4 miles. The field had produced 10,266,896 barrels of oil to January 1, 1934. The oil ranges in gravity from 400 to 420 A.P.I. Although the field is divided into several districts which are more or less clearly defined and separated by unproved territory the term Zwolle field", as used in this report, includes the entire area from Blue Lake on the west side, through Zwolle proper, and eastward, including the Many or Eastern extension.

Jan 1, 1934

Data released by the Commerce Department's Bureau of Economic Analysis show continued gradual change in the real GNP's rate of growth in 1984, which has eased from an annual growth rate of 10.1 percent in the first quarter lo 7.1 percent in the second quarter, and then to 2.7 percent in the third quarter. The automobile industry strike in the last half of September had only a small effect, estimated at less than a 0.1 percentage point reduction in the growth rate. Among the components that comprise the GNP, personal consumption and fixed investment grew at lower real rates in the third quarter than in the second quarter, while net exports decreased. Personal consumption expenditures increased $0.4 billion in the third quarter, compared with an increase of $20.1 billion in the second quarter. Nonresidential fixed investment increased $3.9 billion in the third quarter, compared with $9.6 billion in the second quarter. The other component of fixed investment--residential investment--increased from $60.8 billion in the second quarter to $61.2 billion in the third quarter. Real net exports of goods and services decreased $1 1.3 billion in the third quarter, compared with a $3.1 billion decrease in the second quarter. Although exports increased from an annual rate of $144.7 billion to $150.2 billion, imports increased much more, from an annual rate of $1 56.2. billion to $172.8 billion (table 1).

Jan 1, 1984

By Charles A. Sorrell

This Bureau of Mines publication reviews the structural characteristics of crystalline phases and phase equilibria data for the system NaC1-KC1-AlC13-NaF-KF-AlF3, which encompasses a large number of molten salt fluxes currently used in aluminum recycling. Its purpose is to provide guidelines for research into the relationships between molten salt compositions and their physical properties, notably vapor pressures, densities, surface tensions, and viscosities, knowledge of which is essential to maximizing fluxing efficiencies and metal recovery and minimizing hazardous emissions and disposal problems. In addition, this report describes experimental determinations of sub-solidus compatibility relationships in the system, which is of the quaternary reciprocal type, containing 12 different stable 4-phase assemblages in the solid state. The compatibility diagram serves to define the important compositional planes across which important changes in properties are likely to occur.

Jan 1, 1986

This section presents highlights of world economic and mineral industry performance in 1982, a year characterized by continued recession, and selected 1983 forecasts of economic indicators of importance to the mineral industry, some of which indicate a modest improvement in the economies of the United States and Western Europe. The U.S. Economy in 1982 In 1982 U.S. gross national product (GNP) in current dollars increased at a rate of 4 percent, but GNP adjusted for inflation (real GNP) declined at a rate of 1.8 percent. Yearend 1982 real GNP was at roughly the same level as in 1980 (table 1). Thus no growth in real terms had taken place in the United States during the 1980-82 period.

Jan 1, 1983

By R. F. Waters

Laboratory-scale selective volatilization methods developed by the Bureau of Mines to recover germanium and gallium concentrates from coal fly ash and phosphorus furnace flue dust are summarized. In the better experiments between 85 and 98 percent of the germanium was recovered as the lower oxide and as sulfides, and between 75 and 97 percent of the gallium was recovered as the lower oxide and as the trichloride. Grades of the condensates were inconsistent and varied between a few tenths of a percent and 8 percent, depending on the method used. In the primary extractions of germanium alone the degree of enrichment surpassed 100 to 1, and for gallium the best ratio was 30 to 1. Upgrading of condensates by vaporization retreatment and by leaching and precipitation is discussed. An appreciable degree of mechanical preconcentration by attrition scrubbing and elutriation was possible on two fly ash samples.

Jan 1, 1967

By H. C. Carpenter

This literature study of methods for desulfurizing residual fuel oil was conducted by the Bureau of Mines at the request of the Department of Health, Education, and Welfare. The sulfur compounds in residual fuels are believed to consist chiefly of condensed thiophenes and other polycyclic sulfur compounds. Hydrodesulfurization appears to be the most promising method for desulfurizing these oils and is the only method applicable to all types of sulfur compounds. There are indications in the literature that hydrodesulfurization without hydrocracking of residual oils may require higher pressures than used in present desulfurization processes, but no cost data and little experimental data are available on the higher pressure operation. Literature proposals for hydrogenating residual oils and heavy crude oils are exclusively for hydrocracking the oils to lower boiling products with accompanying partial desulfurization of the residual fuel fraction. Costs of the hydrocracking operations appear the closest available to probable costs of hydrodesulfurizing the oils, and have been reported (in 1955 to 1957) as $500 to $840 investment cost per daily barrel of capacity, with total operating costs of 70 cents to $1.10 per barrel.

Jan 1, 1963

By H. C. Carpenter

This literature study of methods for desulfurizing residual fuel oil was conducted by the Bureau of Mines at the request of the Department of Health, Education, and Welfare. The sulfur compounds in residual fuels are believed to consist chiefly of condensed thiophenes and other polycyclic sulfur compounds. Hydrodesulfurization appears to be the most promising method for desulfurizing these oils and is the only method applicable to all types of sulfur compounds. There are indications in the literature that hydrodesulfurization without hydrocracking of residual oils may require higher pressures than used in present desulfurization processes, but no cost data and little experimental data are available on the higher pressure operation. Literature proposals for hydrogenating residual oils and heavy crude oils are exclusively for hydrocracking the oils to lower boiling products with accompanying partial desulfurization of the residual fuel fraction. Costs of the hydrocracking operations appear the closest available to probable costs of hydrodesulfurizing the oils, and have been reported (in 1955 to 1957) as $500 to $840 investment cost per daily barrel of capacity, with total operating costs of 70 cents to $1.10 per barrel.

Jan 1, 1963

By W. H. Oppelt

The continuous gasification of lignite in an externally heated alloy-steel re-tort was investigated by the Bureau of Mines, Grand Forks, N. Dak., from 1945 to 1951. The main objective of the long-term experimental program was to obtain data on the mechanical performance of this type of gasification retort, particularly the alloy-steel heat-transfer surface of the retort, when operated on large pilot-plant scale. At the same time, extensive experimental data were obtained concerning the effect of process variables and the effect of a limited number of design modifications on gasifier performance. In the period covered by this progress report 4 pilot-plant runs totaling 2,879 hours of operation were completed with the rolled-plate, 310-alloy reaction tube. Over 30 million cubic feet of gas, having H2-CO ratios from 2.1 to 4.4, was made by the partial gasification of 636 tons of 1-1/2-by 3/8-inch natural lignite. Rates of gas generation were from 8,200 to 14,300 cubic feet per hour. Three of the four runs were carried out with the lowered gas offtake or continuous-annulus design modification of the gasification retort. In the final run of the series, gasification of lignite from seven different mines in North Dakota and Saskatchewan, Canada, was investigated at similar combustion-space temperatures and lignite and steam feed rates.

Jan 1, 1955

By Kenneth L. Rubow, Virgil A. Marple, Bruce K. Cantrell

"In a cooperative study by the University of Minnesota and the U.S. Bureau of Mines, diesel exhaust and mineral dust concentrations have been measured for aerosols generated in the laboratory and in five underground coal mines. Three mines utilized diesel-powered haulage equipment and two used all-electric equipment. Two source apportionment techniques have been applied to differentiate between the mineral dust and diesel exhaust aerosol concentrations measured. The first technique, using a micro-orifice, uniform deposit impactor (MOUDI) for size selective sampling, is based on modeling aerosol size and the premise that the diesel exhaust portion of the aerosol is predominantly submicron and the mineral dust portion is mostly greater that one micrometer in size. The second technique, Chemical Mass Balance (CMB) modeling, was used to referee the analysis of diesel exhaust and mineral dust aerosol concentrations from the size selective sampling results.The MOUDI size distribution data were modeled to obtain parameters describing the fine and course fractions of the sampled aerosol and to estimate the contributions to each mode from both mineral dust and diesel exhaust aerosol sources. The results showed the size distribution of the mixed aerosols exhibited two definite modes with the minimum between the modes occurring at 0.8 µm. Less than 5 pct of the coal mine diesel aerosol was found in the coarse size fraction. CMB analysis confirms the original premise for using aerosol size to separate diesel exhaust and mineral dust aerosol during sampling.Based on the results from the size selective sampling, a personal diesel aerosol sampler has been developed for measuring diesel aerosol mass concentrations. Th.is sampler uses an inertial impactor to size separate the respirable aerosol at 0.8 µm. All material less than 0.8 µm is collected on an after filter for subsequent gravimetric analysis."

Jan 1, 1990

By Will H. Coghill, F. D. DeVaney

"Many of the iron ore deposits on the western end of the Mesabi Range Minnesota consist of the so-called ''wash ores."" Because of their high silica content these ores must be washed or concentrated to make them merchantable. Washing plants have been in operation for 20 years, during this period large quantities of tailings have accumulated in tailings ponds. These tailings contain the aggregate millions of tons of iron oxides which, if recovered, would greatly to the available tonnages and to the revenues of the mining companies. It the purpose of this paper to outline give results of concentration tests on tailings.In order that the reader may understand more clearly the type of material under consideration, a short description of the characteristics of the wash ores of the Western Mesabi Range and a brief resume a washing methods that have been are now being employed will be given. Appleby and Newton4 In their description of the district and of the ores say:The Western Mesabi district embraces the territory west of the town of Nashwauk in Itasca County. The territory to the east of this dividing line is known as the Central and Eastern Mesabi district. This subdivision is rot wholly arbitrary. While the ore bodies in the two districts resemble each other in. shape, size, and general structure, there is a marked and very important difference in the character of the respective ores. For purposes of comparison, the western deposits have been called washable ore bodies, and the central and eastern, standard ore bodies. The latter ores are the result of natural concentration processes which have teen carried far enough to produce a large proportion of high-grade ore Wet can be marketed direct; the Western Mesabi ores present a lesser degree of natural concentration and are as a rule of too low grade to admit of marketing without preliminary treatment. In many cases the grade can be improved by washing, hence the material is called washable ore. Exceptions to thin general rule may be noted in both districts. Many of the Western Mesabi ore bodies contain quite a proportion of merchantable ore. There are also portions of central and eastern Mesabi ore deposits which are of low grade and which can be improved by washing."

Nov 1, 1930

By William W. Adams

The stone-quarrying industry of the United States, including such related operations as rock crushing, rock dressing, and the manufacture of cement and lime, reported a larger volume of employment in 1934 than in 1933. Reports from the operating companies to the United States Bureau of Mines showed an increase in the number of men employed, number of man-days of employment, and total number of man-hours of labor performed during the year. Moreover, the average worker had a longer period of employment during 1934, the gain amounting to 11 percent over 1933. The increase in employment was accompanied by no increase in accidents for the industry as a whole; in fact, the accident rate for 1934 was a fraction lower than the rate for 1933. In some branches of the industry the frequency of accidents increased, but these increases were more than offset by reductions in rates for other branches. Reports for 1934 were received from 1,403 active plants. The working force averaged 64,331 men for 204 days per man, and the total period of employment for all of the men was 95,258,880 man-hours. Each employee averaged 1,481 hours of work during the year. The total number of hours of labor represented a gain of more than 8 percent, and the average working time per employee showed a gain of 62 hours per man.

Jan 1, 1936

When the Organic Act of 1910 established the Bureau of Mines within the Department of the Interior, the Bureau's programs involved only health and safety research and, education, and fuels testing. As the Federal Government's primary agency for research in minerals, the Bureau has expanded its scientific and technological investigations to mining, processing mineral substances, eliminating occupational health and safety hazards in the mineral industries, economic development, and resource conservation. Today, Bureau activities cover a broad spectrum of programs for meeting the diverse (and sometimes conflicting) needs of mineral industries, government, and the public. In the 1960's, the Bureau initiated programs to resolve environmental problems associated with past mining and mineral processing. In the 1970's, the energy crisis raised the national consciousness concerning our limited supplies of domestic mineral and fuel resources. Dependence on foreign sources of raw materials critical to our national economy and competition from other countries for these world supplies stimulated the need to conserve and use with intelligence the Nation's minerals, metals, and fuels.1

Jan 1, 1977

By Thomas F. Anderson

(Measurements of stable isotopic variations (sulfur, carbon, and oxygen), supplemented by chemical, mineralogical, and petrographic analyses have been used to investigate the processes responsible for : (1) the incorporation of sulfur in coal, and (2) the (development of permineralized peat zones ("coal balls"). Sulfur isotopic results indicate that there are two principal sources of sulfur in the Pennsylvanian coals from the Illinois Basin: (1) "primary" sulfur assimilated by plants (low-sulfur coals), and (2) "secondary" sulfur produced by reactions involving H2S that was produced by the anaerobic reduction of sulfate in seawater which permeated the peat during post-depositional marine transgressions (the dominant source of sulfur in high-sulfur coals). Sulfur isotopic compositions of low-sulfur coals in Several Tertiary basins of Wyoming are consistent with a plant sulfur source. However, the inverse correlation between content and isotopic composition of sulfur observed in coals from the Powder River Basin suggest some "secondary" additions to these low-sulfur coals. Seveeral Quaternary (freshwater pears which were submerged by sea-Level rises during deglaciation over the past 30 ka have sulfur contents and isotopic compositions similar to high-sulfur coals. Carbon and oxygen isotopic compositions of calcareous coal balls from North America and Europe suggest that (1) the carbonate was derived from variable proportions of oxidized plant matter (typically predominant) and inorganic carbonate, and (2) the carbonate minerals were precipitated from fresh-to-brackish waters. Local geochemical and hydrological conditions were apparently more important than regional depositional environments in controlling the source of carbonate and the development of coal balls.

Jan 1, 1983

By E. G. King

Thermodynamic calculations involving the oxides of tungsten and molybdenum have been hampered by lack of accurate entropies and high temperature heat contents. This paper presents work by the Federal Bureau of Mines on new low-temperature heat-capacity data leading to the evaluation of the 298.15° K. entropies of tungsten dioxide and tungsten trioxide, as well as high-temperature heat contents (above 298.15° K.) of molybdenum dioxide, molybdenum tri-oxide, tungsten dioxide, and tungsten trioxide. Included are heats of fusion of the two trioxides. The heats of formation at 298.15° K. of these four oxides are tabulated as measured by Mah4 5/ of this laboratory. Included also are the 298.15° K. entropy of Mo02 measured by Kin 6/ of this laboratory, and that for Mo03 according to Kelley and King.7/ These basic data provide a consistent compilation from which to perform accurate thermodynamic calculations involving these compounds. No previous low-temperature- heat-capacity measurements have been reported for tungsten dioxide. Seltz, Dunkerley, and DeWitt8/ measured the low-temperature heat capacity of tungsten trioxide. The only previously-reported high-temperature heat-content measurements for any of the oxides were conducted by Cosgrove and Snyder,9/ who measured molybdenum trioxide to 1,300° K.

Jan 1, 1960

By D. G. Leddy, J. B. Johnson, L. D. Gratz, S. T. Bagley

"Studies have been conducted at Michigan Technological University (MTU) for over twenty years on methods for characterizing and controlling particulate emissions from heavy-duty diesel engines and die resulting effects on regulated and unregulated emissions. During that time, control technologies have developed in response to more stringent EPA standards for diesel emissions. This paper is a review of: 1) modem emission control technologies, 2) emissions sampling and chemical, physical and biological characterization methods and 3) summary results from recent studies conducted al MTU on heavy-duty diesel engines with a trap and an oxidation catalytic converter (OCC) operated on three different fuels. Control technology developments discussed are particulate traps, catalysts, advances in engine design, the application of exhaust gas recirculation (EGR) and modifications of fuel formulations. Methods for dilution tunnel sampling, particle size analysis, chemical analysis with emphasis on polynuclear aromatic hydrocarbons (PAH) and nitro-PAH, and biological characterization using mutagenic activity (Ames) assays are described, along with statistical approaches to experimental design and data analysis.In studies at MTU, both particulate traps and an OCC have been shown to be effective for the reduction of total particulate mauer (TPM), with the OCC being better al reducing all forms of hydrocarbon emissions, including PAH and nitro-PAH, and with the traps being better at removing the solids (SOL). The use of low sulfur fuel (0.Ql % by mass) has led to additional reductions in TPM; the low sulfur fuel has been shown to reduce the number of small, nuclei-mode particles for one of the engines tested. PAH, nitro-PAH, and mutagenic actively levels generally decreased with use of either the traps or the OCC.INTRODUCTIONDuring the 1980s and the early 1990s there have been significant advancements in the development of technology to control diesel particulate emissions. Efforts have been focused on internal control of the engine by design, the use of after-treatment devices, and improvements in fuel formulations to reduce all the diesel emissions. The research and development activities have been driven by the need to meet the US EPA heavy-duty vehicle standards shown in Table 1. The important standards for new technology are the 1994 heavy-duty vehicle 0.1 gm/bhp-hr particulate, the new urban bus 0.05 gm/bhp-hr particulate standard for 1996 and the heavy-duty vehicle 4.0 gm/bhp-hr NOx standard for 1998."

Dec 1, 1995

By C. W. Owings, J. J. Forbes

"Although coal-mine explosions rank third among causes of underground fatalities, they receive more wide-spread attention than any other accidents in mines because frequently many persons lose their lives in a single disaster. Each bituminous coal-mine explosion endangers the lives of approximately 100 persons--the average number employed underground in a commercial mine. A critical analysis of coal-mine explosions in a restricted district gives a cross-section of relative existing explosion hazards, of common causes of ignitions of gas and dust, and of effective prevention measures. The Safety Division of the United States Bureau of Mines is collecting data on coal-mine explosions in the various States, and this circular is one of a series analyzing the causes and recommending methods for thy prevention of similar occurrences,The data on this circular are based on records of the United States Bureau of Mines and the West Virginia Department of Mines. Unfortunately practically all of the early records were destroyed by fire in the State House at Charleston, W. Va.; the remaining records were made available to the authors by N. P. Rhinehart, chief of the Department of Mines, and his cooperation is gratefully acknowledged.The earliest available reference to coal in West Virginia is that made by John Peter Lally who in 1742 found ""a great plenty of coals"" near a river later called Coal River. In 1809, Nicholas Roosevelt found coal along the Ohio River and used it on the New Orleans, said to have been the first steamboat west of the Allegheny Mountains. In 1810, Conrad Cotts opened a mine near Wheeling and sold coal for domestic purpose in 1812, a mine was opened on the Ohio River opposite Mason City and produced 1,200 bushels of coal that year. In 1840 the total West Virginia coal production was 298,691 tons; in 1863, the production had increased to 444,468 tons, and in 1883, to 2,335,833 tons. During this period apparently most of the coal was extracted from coal outcropping on the hillsides; little danger of gas ignition existed at that time, but explosions from blown-out shots occurred frequently. On February 22, 1383 the West Virginia legislature enacted legislation providing for a mine inspector to inspect the mines of that State, to prevent mine accidents, and to insure properly ventilated mines.In a special report to the Governor on December 31, 1884 the Inspector of Mines reported:We have 5 shafts, in 4 of which there is more or less gas; and in 1 of our drift mines there was an explosion on the 27th day of March 1880, whereby 2 men were killed and a boy badly burned.Table 1 lists 287 explosions in West Virginia coal mines. Several early explosions were listed in the annual reports of the West Virginia Department of Mines as ""blown-out shots"" or ""powder explosions"". The injuries usually were described; explosives accidents have been eliminated from these and other available data, and only those in which dust or gas were involved have been included in this paper as explosions."

Sep 1, 1934