Search Documents

By E. D. Gardner

Oil shale, a long-considered potential source of motor fuel in the United States, is found over an extensive area in the Green River formation in Colorado, Utah, and Wyoming.4/ Oil has been retorted commercially from shale in Scotland for many years,5/ and work done by the Bureau of Mines and other investigators has shown that it is technically feasible to extract oil from American shales.6/ By refining, the shale oil may be converted into marketable products similar to those manufactured from crude petroleum. The present paper, which was finished in 1936, discusses methods that would be adaptable to mining certain American shales, and the treatment applies specifically to conditions iii the Green River formation on Naval

Jan 1, 1942

As a part of its overall wealth in fuel resources, the United States possesses large reserves of coal of ignite rank. According to recent estimates of the Federal Geological Survey (3, 5),l/ the assured lignite reserves of this country amount in total to over 463 billion tons, equivalent to 24 percent of our total national coal reserve on a tonnage basis and 15 percent on a heating-value basis. Distribution and relative amounts of United States coal and lignite reserves are indicated in figure 1. By far the largest proportion of our lignite reserves, over 95 percent is found in North Central States, principally in North Dakota, South Dakota, and Montana, in the vast coal-bearing structural grouping designated as the Fort Union formation. Of the remaining United States reserves, all but a fraction of 1 percent are found in a series of relatively scattered deposits in Texas.

Jan 1, 1954

By John J. Sammarco

The U.S. Bureau of Mines has developed a regulated, intrinsically safe, rechargeable power supply for portable electronic equipment for underground use. The regulated output is ideal for microprocessor power requirements and is suited for operation in hazardous environments. Two rechargeable, sealed batteries are contained within the power supply. Provisions are made to use an external source of power if these batteries fail. Provisions are also made to charge these internal batteries when needed. The circuit is composed of three main circuits: the main regulator circuit, the input protection circuit, and the output protection circuit. The main regulator circuit provides remote voltage sensing, current sensing, fault monitoring, and internal thermal protection. The input protection circuit checks for excessive input current and low battery conditions. The output protection circuit contains two overvoltage detection devices. Schematics, a parts list, and a calibration procedure are provided in this report to enable readers to fabricate the power supply.

Jan 1, 1989

By H. F. Feldmann

This work was done to provide thermodynamic, electrical, physical, and compositional data on the seeded combustion plasmas of seven coals for the design of MHD generators. The systems were assumed to be at equilibrium, and the design data were generated by solving for the composition of both gas and liquid phases with a digital computer. The coals reported in this study include a western subbituminous, a Pennsylvania anthracite, and five representative bituminous coals. The data include dewpoint temperatures of both slag and seed. A Mollier diagram for each coal is given to allow graphical generator calculations.

Jan 1, 1970

As part of the overall development of a borehole mining system -develop backfilling techniques to reduce possible damage to the environment caused by either the cavities or the piles of sand tailings that result from in-borehole hydraulic mining. (Borehole mining is described in technology News No. 56.) Approach Water filled cavities at the bottom of boreholes are rapidly and economically backfilled by jetting a sand-tailings slurry underwater. How It Works The Bureau of Mines borehole mining system creates a cavity having a horizontal diameter of more than 50 feet. (See photograph). This cavity can be backfilled with much of the sand previously mined. The sand tailings or similar backfill material is dumped by a front end loader into a slurry mixing tank at the rate of about one ton every three minutes. Enough water is added to give a thick, but pumpable slurry. The slurry is pumped down the borehole through a string of 4-inch pipe to the cavity. After passing through a right elbow at the end of the pipe, the slurry is ejected through a nozzle. The resulting slurry jet emplaces the backfill at the outer wall of the cavity. To obtain an even distribution of fill in the cavity, the nozzle is slowly rotated. The nozzle and pipe assembly is supported from a turntable on the surface. See diagram.

Jan 1, 1981

By Virgil Miller, R. G. Knickerbacken

"INTRODUCTION The Bureau of Mines work reported by the Metallurgical Division 4/ in 1934 shows the possibility of producing artificial manganese ore by pre- ferential oxidation of manganese from spiegeleisen produced from manganiferous iron ores of the Cuyuna range, Minnesota. A three-step process is described as being capable of producing a ferrograde ore from this type of low-grade, domestic, strategic material. However, the melting temperature in the last step of the process that forms the manganese product is high, and the phosphorus content is not easily controlled. Also, the tenor of the manganese in the product is not comparable with other methods that use less process energy.Lofquist 5/ patented an improvement of the above three-step smelting method, in which sulfide was added to lower the melting point of the product.More recently, reputedly successful attempts have been made to reduce iron preferentially from manganiferous iron ores, simultaneously removing the phosphorus with the iron, by means of an unusually high temperature blast and excess coke.Anson G. Betts 6/ patented a process for the matte-smelting of manganese ores, in which the ore was mixed with pyrite and enough carbon or coke to serve as thermal energy and reducing, agent in a manner similar to the standard blast-furnace process. This process was intended to give pig iron, a manganese-iron matte, and a waste slag. Wood, Barrett, and Porath 7/ presented data on the treatment of low-grade, domestic, manganiferous iron ores and low-grade, domestic manganese ores by this Betts mattes pelting process."

Aug 1, 1942

By J. D. Warne

The ferberite district of Boulder County, Colo., has been an important producer of tungsten since 1900. During World War I, high prices for tungston concontrates resulted in a brief period of intense activity, and the production in 1917 was 2,707 tons of 60 percent W03 concentrates. Production declined thereafter, and in 19.2 the tungsten produced in Boulder County represented about 4 percent of the Nation's output, being exceeded only by the scheelite production in California, Nevada, and Idaho. Boulder County has boon an important source: of tungsten in the Korean emergency; the present report does not describe this recent activity, as it will be covered by a future publication. Tungsten occurs in small ore shoots of narrow and irregular veins. Most of the ore shoots have been found outcropping on the surface. Core drilling; has been used by the larger operators to explore for new veins and to locate extensions of known veins.

Jan 1, 1953

[ ]

Jan 1, 1981

By Charles B. Carpenter

For many years, studies of ground movement and subsidence accompanying subsurface mining operations have been part of the research program of the Bureau of Mines. Periodic observations by engineers of the Mining Division of the Bureau of man-built structures beneath which mining operations are conducted offer indisputable evidence of subsidence in the form of creeks in masonry structures and fractures and depressions in the surface of the earth. As the removal of subsurface rock and earth material by mining, especially by the room-and-pillar method, is equivalent to withdrawing some of the foundation of a building, subsidence of the formations above, the mining levels in certain areas is easily understood as a gravitational adjustment of the overlying earth formations.

Jan 1, 1940

By Charles B. Carpenter

For many years, studies of ground movement and subsidence accompanying subsurface mining operations have been part of the research program of the Bureau of Mines. Periodic observations by engineers of the Mining Division of the Bureau of man-built structures beneath which mining operations are conducted offer indisputable evidence of subsidence in the form of creeks in masonry structures and fractures and depressions in tie surface of the earth. As the removal of subsurface rock and earth material by mining, especially by the room-and-pillar method, is equivalent to withdrawing some of the foundation of a building, subsidence of the formations above, the mining levels in certain air-as is easily understood as a gravitational adjustment of the overlying earth formations.

Jan 1, 1940

By R. E. Chaney

This report summarizes the research on the Strategic and Critical Materials Program tasks conducted at the Idaho National Engineering Laboratory (INEL) between Mdy 1983 and April 1984. The work is divided into two areas: 1. Production Technologies - Tasks directed at developing advanced extraction technologies ? Biologically-Assisted Minerals Processing ? Metal/Gas Reactions and Thermal Plasmas ? Dehydration of Aluminum Chloride Hexahydrate. 2. Conservation/Substitution Technologies - Tasks directed toward establishing the technical processing base which will permit the use of advanced materials ? Joining of Rapidly Solidified Alloys (RSA) ? Joining of Silicon Nitride-Based Ceramics ? Nondestructive Evaluation of Ceramic and RSA Joints and Materials.

Jan 1, 1984

By W. W. Adams

With greater production of coal per man-hour of work than ever before achieved, the coal-mining industry of the United States established a better safety record in 1941 than in any year since 1930, the earliest for which complete reports of nonfatal as well as fatal injuries were collected by the Bureau of Mines, United States Department of the Interior. In only one year (1933) of the 12-year period 1930-41 was the fatal-accident rate better than in 1941, whereas the rate for nonfatal accidents was better in 1941 than in any previous year. Accident and employment reports received from mine operators, together with fatal-accident reports received monthly from State mining departments and inspectors, showed that 546,692 men were employed in and about the coal mines of the United States during the calendar year 1941. This number does not include office employees or coke-oven workers. The increase of 1.3,426 over the number of employees in 1940 was accompanied by a gain in man-hours of work performed at the mines and an increase in average number of hours worked per man during the year.

Jan 1, 1944

By Sean Gallagher, John R. Bartels, Dean H. Ambrose

Remote operation of continuous miners has enhanced the health and safety of underground miners in many respects; however, numerous fatal and non-fatal continuous miner struck-by accidents have occurred when using remote controls. In an effort to prevent these injuries, NIOSH researchers at Pittsburgh Research Laboratory examined the workplace relationships between continuous miner operators and various tramming modes of the equipment using motion captured data, predicted operator response times, and field- of- view data to determine causes of operator-machine struck-by events in a virtual mine environment. Factors studied included machine speed, direction of escape, operator facing orientation relative to the machine, work posture, distance from machine, and operator anthropometry. Close proximity to the machine, high machine tramming speeds, a right-facing orientation and operator positioning near the tail all resulted in high risk of being struck. It is hoped that this data will provide an improved rationale for operator positioning for remotely operated continuous miners.

By F. S. Crawford

The wide variation in the medical facilities, type of accident reports and provision for the welfare of employees, in addition to the compensation provided by the various State laws,- was -studi-eci, by the.. wri-ter in the Lake .. Superior_ r.egion . .. - -Several cDmpanies f~rnished. the information which follows. Names have been omitted , ~ut the information should be of .intere·st to companies desirous of improving t_his branch of thej..r accident-prevention work. : . . --Because a summary of the metho.ds used would merel:y: result in _ a.n a.ttempt to set _up an ideal, it was concluded that in preparing this paper a statem.ent .of_ tbe individual methods of -each company wou-l d .b-e .Qf .. the most inte-res.t, . and the.y h~ve . been .. li.steq with .no regard to the size of the company . . ··· -In the - appendix are -a -number of report. forms used by .various _operators for reporting accidents to t he company and .to the State. These are self- explanatory. and many a re mentioned in -the body of circu-1-ar-.

Mar 1, 1932

Rock property tests were performed on NX-size diamond drill core from the roof, floor, and coal from the longwall mining section of Federal No. 2 mine, West Virginia. The purpose of these tests was to determine the engineering properties of the various strata as part of a ground control study of the longwall operation. The following tests were performed: 1. Uniaxial compressive strength, Young's modulus, and Poisson's ratio 2. Triaxial compressive strength 3. Brazilian tensile strength 4. Modulus of rupture 5. Specific gravity Thirteen boxes of core delivered to the University on April 1, 1974 were identified as follows: 2 PTR 1 -2 boxes of roof rock 2 PTF 1 -2 boxes of floor rock 2 PTR 2 -2 boxes of roof rock 2 PTF 2 -2 boxes of floor rock with approximately 3 ft of coal in Box 2 (designated 2 PTC 2) 2 PTR 3 -2 boxes of roof rock 2 PTF 3 -2 boxes of floor rock 1 PC 5 -1 box of coal

Jan 1, 1976

By Richard C. Moore

The U.S. Bureau of Mines contracted a study to estimate what effects the underground mining of thick coal seams in the western United Slates would have on the surrounding water resources. Potential coal fields in the western United States where this type of mining might occur were identified. The foreign literature was searched for studies of effects on hydrology from thick seam underground coal mining. Based on the limited information obtained from the foreign literature, estimates of the effects of this type of mining on the ground and surface water in the western states were made.

Jan 1, 1980

Provide an unobstructive means of measuring small changes in distance from roof to floor or from rib to rib of a mine opening and the rate of closure in order to help operators of under-ground mines detect hazardous ground conditions. Approach A small ultrasonic measurement system was developed to detect g round movement and define closure rates. How the System Works The system contains two parts: a transducer and a readout device. The small ultrasonic transducer, similar to an audio speaker diaphram, is plucked with an ultrasonic frequency every six seconds. This frequency wave is sent through the air and reflected back to the transducer off any surface at which the transducer is pointed. The amount of time needed by the ultrasonic wave to make this round trip is accurately measured using a precise oscillator / timer and is converted into a measure of distance. The accurate 6-second time interval is used to convert any subsequent changes in the reading to a rate of change in feet per minute. Two readings are then displayed alternately on the readout instrument.

Jan 1, 1984

By Henry P. Wheeler

As recently as 1915, helium was available only in very small quantities at a cost equivalent to $2,500 per cubic foot. It was a laboratory curiocity, and its properties were of interest to a limited number of scientists (11).3/ During the past 30 years, however, helium has grown from a plaything of scientists to a factor of importance in the prosecution of the recent war. Navy blimps filled with nonflammable helium proved to be more than a match for German submarines operating in the Atlantic. American bombers were able to fly unheard-of distances to drop bombs on Tokyo, Nagoya, Yokahama, and other Japanese cities because they had been made lighter with magnesium, arc-welded in a helium atmosphere. The Army utilized helium-filled radio-sonde balloons to obtain vital information concerning weather conditions affecting D-day invasions and other military maneuvers.

Jan 1, 1946

By Richard C. Wang

The U.S. Bureau of Mines established a wire rope research laboratory to examine the factors that affect the safety and the useful life of wire rope. In the most recent work, two 32-mm 6x27H flattened strand ropes were degraded on a bending fatigue machine. The two tests were run at constant loads of 285 and 347 kN or safety factors of 2.5 and 2. Nondestructive and tensile strength tests were performed on samples of the ropes to determine the relationship between rope deterioration and rope breaking strength. Neither the area loss nor the number of broken wires measured from nondestructive tests could be used as clear indicators of the loss of strength. However, it was found from the tensile tests for both rope specimens that the strength loss was associated with the reduction of breaking strain. This suggests that measuring the strain of many short sections of a rope in the elastic region may locate the high stress sections and thus delermine the condition of the rope.

Jan 1, 2010

To be able to continuously monitor the noise to which underground workers are exposed as a better way to help prevent hearing damage. The Approach: The Bureau of Mines has developed a Time-Resolved Audio Dosimeter which can be worn by miners to record noise level every 30 seconds and store It in a miniature solid state memory. Figure 1 is a photo of the dosimeter. [ ] How It Works: Acoustical noise is picked up by a micro-phone and fed to a sound level meter which produces a d-c voltage proportional to the A-weighted sound pressure level. (As specified by federal regulations, the A-weighted sound pres-sure level approximates the response of the ear by discounting the higher and lower frequency components of the noise.) This d-c voltage controls an oscillator which, together with related circuitry, produces a pulse train having a frequency that's proportional to the noise level.

Jan 1, 1975