Search Documents

By J. R. Hamke

THE WILLISTON basin is the largest known sedimentary basin on the North. American continent. Two-thirds of this large basin lies within the United States in Montana, North Dakota, and South Dakota. Less than 10 years after the first commercial oil discovery in North Dakota in 1951, the petroleum became one of the largest industries in the three-state area. Crude petroleum is now the most valuable mineral resource in the area. In 1960, the basin produced 39 million barrels of worth $100 million at the wellhead. Most of the 137 oil pools covered to date are in Paleozoic carbonates at depths ranging from 3,000 to 13,000 feet. The major producing fields, centered on the Cedar Creek anticline in Montana and the Nesson anticline in North Dakota, produce from depths below 6,000 feet. This report presents descriptions of all phases of the Williston basin petroleum industry, including leasing, exploration, geology, drilling, production, transportation, and refining. Engineering, physical, and production data, maps, and crude petroleum analyses for 137 separate oil pools are included.

Jan 1, 1966

By Mark R. Pettitt

Noise surveys conducted in underground coal mines have consistently indicated that auger mining machines subject the operator and helpers to excessive noise exposure. The machine cutting heads have been identified as the primary noise source. This report documents the research program conducted to (1) investigate the nature of the cutting head noise problem, (2) develop noise control concepts, (3) devise in-mine survivable techniques to implement the noise control concepts, and (4) build and demonstrate prototype reduced-noise auger miner cutting heads. The dynamic forces generated during coal cutting by the brittle fracture of coal are predominently low frequency. The low-frequency (less than 1500 Hz) structural response of the cutting head, therefore, determines the noise radiated by the cutting head. The most feasible methods of reducing the cutting head low-frequency response are to increase both the structural stiffness and the low-frequency damping. A technique was devised to achieve these goals. The standard plate helix was replaced by a sand-filled hollow helix of triangular cross section, and the core diameter was increased with an attendant reduction in helix depth. Extended in-mine tests demonstrated the operational capability of the reduced-noise auger cutting heads. The simple noise control concepts are valid for all continuous miner cutting heads. The sand-filled hollow helix technique, which achieved a 10 dB(A) noise reduction for the auger, can be used on any helix-bearing Cutting head.

Jan 1, 1983

By James J. Dowd

The investigation to evaluate the reserves of coking coal in the United States suitable for the manufacture of metallurgical coke is being made by the Bureau of Mines in three parts: (1) To estimate known (measured plus indicated) recoverable reserves of all coking coal; (2) to upgrade marginal coals through effective preparation; and (3) to study the carbonizing properties of coals and coal blends not now widely used for metallurgical coke making. This is the sixth of a series of reports giving the results of studies by counties under part (1) of the investigation. (See appendix.) This report covers Fayette County, Pa., which comprises the Uniontown and parts of the Brownsville, Connellsville, Donegal, Waynesburg, Masontown, and Confluence, Pa., Morgantown and Bruceton, W. Va., and Accident, Md., quadrangles. (See fig. 1.) A short resume of the chemical and carbonizing properties of the coals ar.9 included. Data on the coal beds in this county were obtained from mining companies, land companies, individual landowners, and other sources of authentic information.

Jan 1, 1951

By Sabri Ergun

Cost estimates and technical feasibility are compared for six chemical coal cleaning technologies. The comparison is based on conceptual application of the chemical cleaning methods for removal of pyritic and organic sulfur from a utility grade bituminous coal. The process layout includes receipt of 8,000 tpd ROM coal, fine coal pulverizing, desulfurization, and preparation of a compacted clean coal suitable for storage and shipment. The methods are: the Magnex iron pentacarbonyl process, the KVB dry oxidation process, the Battelle hydrothermal caustic leaching precess, the TRW Meyers ferric ion leaching process, the Ledgemont oxygen/water leaching process, and the Bureau of Mines/Energy Research and Development Administration air/water leaching process. Capital costs estimated for the desulfurization operation alone, scaled to 8,000 tpd, range between $14 MM and $122 MM, while estimated operating costs for desulfurization alone on the same scale of operation range between $7 and $17 per ton clean coal produced. Relatively little is known about the chemical cleaning of coal, and present cost estimates indicate that the method might not be competitive at its present state of development when used alone to clean utility grade coals for sulfur removal. The principal attractiveness of chemical coal cleaning lies in its potential for combination with physical cleaning to produce cost competitive compliance coals in a combined process with high-Btu yields.

Jan 1, 1977

By H. Kenworthy

"INTRODUCTION ..Although the occurrence of iron ore in Missouri was recognized by Marquette as early as 1673, the first known mining and smelting operation was conducted in 1815. This operation was near Arcadia, Iron County, the first of its kind west of the Mississippi-Ohio River system. Several small furnaces of short life were erected in Missouri in the ensuing 30 years. However, until the extensive deposits of Iron Mountain and Pilot Knob were opened between 1843 and 1850, the state remained a minor producer of iron. It was this district which was chiefly responsible for the prominent position Missouri held in the iron industry until the late 1880's. At this time the easily minable high-grade ores became exhausted and the discovery of the immense Lake Superior deposits depressed the raw-ore price to such an extent that any mines ceased to operate. 3/Small yearly production of iron ores continued in Missouri to the present. Owing to war demands for hard ore suitable for open-hearth steel, the M. A. Hanna Co., through its subsidiary, the Ozark Ore Co., reopened the Iron Mountain, deposits and installed new equipment in an old concentrator to handle the low-grade ores left from previous operations. At present, ore production is from open pits, but underground mining is contemplated in the future. About 2,000 tons a day of iron ore is treated by gravity concentration of material from the open pits in the immediate vicinity. The concentrate is shipped to the Birmingham, Ala., district and to Granite City, Ill., for smelting. The coarse tailing is sold for ballast and concrete aggregate. The iron requirements of the concentrate stipulated by the purchaser are not difficult to meet, but the phosphorus is frequently higher than desired. For 1946 the concentrates averaged 54.18 percent iron and 0.235 percent phosphorus with low sulfur. The Ozark Ore Co. concentrate, however, sometimes contains as much as 0.40 percent phosphorus. The phosphorus in ores from those portions of the deposits wherein the phosphorus occurs with siliceous gangue is readily rejected in the milling, but in much of the ore the phosphorus is associated with the iron and concentrated with the iron minerals. Selective mining is impossible owing to the spotty occurrence of the phosphorus mineral. Often within 5 feet the ore will change from low phosphorus to high phosphorus, and it would be expedient to find a method of rejecting enough phosphorus at the mill from the latter type of ore to meet the phosphorus specification."

Feb 1, 1948

By S. P. Polack

"INTRODUCTION The purpose of this circular is to correlate the information obtained during personal investigations at the sites of four rock tunnels in the process of construction and information obtained from the records and personal views of the constructors of two other tunnels that were not visited during the, excavation phase of construction and to present this information for the benefit of those who contemplate future construction of rock tunnels.Modern mechanized coal mining requires better, safer, properly alined haulageways and beltways; consequently, better understanding of tunneling methods by coal-mining men will be necessary. The possibility of future high-speed haulage systems utilizing rock tunnels in the more solid rock strata above or below the coal beds must not be discounted. In the past, tunnels have been driven for use in draining and unwatering inundated coal mines. At present, the need for such tunnels is very evident in some parts of the coal-mining regions, notably in the Pennsylvania anthracite fields, and studies along these lines are in progress. The average coal-mining man has little time or opportunity to visit tunnels while they are being exca-vated; therefore, it is hoped that this information will assist him in constructing tunnels safely if he is required to do so in the future.The tunnels described herein differ in size, shape, usage, and, in many instances, in their geological aspects. Full-face, heading and bench, and pilot-tunnel, and enlargement methods of excavation were utilized.The roof-support methods show diverse designs and materials of construction to suit each purpose and condition. The superiority of steel roof support over wood is demonstrated beyond doubt and is shown clearly in the photographs included in this circular.The illustrations (photographs taken by the U. S. Bureau of Mines, the U. S. Corps of Engineers, and others) show many of the necessary steps taken during the excavation and the erection of roof support in tunnels under construction."

May 1, 1950

By G. F. Kuncir

The time-cost-risk analysis described herein was performed as part of an evaluation of the Advancing Oil Shale Mining Technology Program performed by The Aerospace Corporation. The objectives of this analysis are to assess the feasibility of the program relative' to time and cost constraints, and to determine the probabilities of achieving various technological goals. A combination of standard program planning and analysis techniques were used to achieve these objectives. These included a critical path analysis, a resource allocation analysis, and a risk analysis.

Jan 1, 1977

By William F. Hahn

The Bureau Of Mines recognized the desireability of illuminating working places in trona mines. This report describes two illumination system designs, their demonstration and evaluation on a Jeffrey 120HR continuous mining machine in an active working trona mine in Wyoming.

Jan 1, 1980

By F. S. Wartman

This paper gives an account of the production of ductile-grade titanium powder in 100-pound batches by reduction of purified titanic Chloride with magnesium, grinding, leaching, and magnetic-separation of the reaction product. Apparatus, technique, and methods of controlling product quality are described and some data on operating costs are given.

Jan 1, 1949

By Fred N. Kissell

In This Chapter [Ventilation and methane sampling guidelines for conventional shafts Dealing with restricted spaces where methane can accumulate Ventilation and methane sampling at raise bore drills and Filling shafts at closed coal mines] It is not unusual to encounter methane gas during shaft excavation or shaft-filling operations. Shafts into coalbeds usually produce the most methane, so the information in this chapter applies primarily to shafts at coal mines. Nevertheless, much of the information is relevant for noncoal mines that have methane in the mine or in the overlying strata. METHANE IN SHAFTS EXCAVATED BY CONVENTIONAL MEANS (DRILL, BLAST, MUCK) [ ] Ventilation. Shafts excavated by conventional means are ventilated with a fan on the surface connected to ductwork that extends down into the shaft (Figure 9–1). Shafts into coalbeds should have ventilation systems designed to handle the higher gas flows to be expected as the shaft excavation passes through any over-lying gas-containing strata and nears the coal-bed to be mined. Following are some simple ventilation guidelines for the minimum amount of air required and the selection of the ventilation duct: • Provide enough air to meet the mini-mum OSHA tunnel requirement of 30 ft/min air velocity in the open shaft, as specified in 29 CFR2 1926.800(k)(3). For example, a 20-ft-diam shaft having

Jan 6, 2006

By L. C. IlsLey, M. W. Von Bernewitz

"Introduction.Several hundred thousand open lights are daily carried in coal mines of the United States, each lamp being a menace to life and property through fire or explosion. They have been responsible for many disasters in the past, and will be again. Flame safety lamps have been available for over a hundred years, but during the last ten years safe and practical electric lamps have been perfected. These have eliminated many of the flame safety lamps, and in a few mines have replaced open flame lamps. But there are still more than twice as many open lamps as electric lamps in our mines, and the open lamps should be discarded in favor of an approved type of electric lamp. There are several electric miners' lamps which have been approved by the Bureau of Mines for safety and efficiency, give good light, and are easily maintained and carried, some flame safety lamps will always be used, hut mostly for detecting gas; although they might be supplanted if some simple, reliable, and cheap gas detector were developed.Explosion Hazards from Open Lights.An open light and gas*** constitute a vicious hazard; while if there be coal dust present in the vicinity the consequences are multiplied many times. An open light and black blasting powder also constitute an explosion hazard, vividly attested by several serious disasters."

Jan 1, 1924

By W. G. Phillips

This report presents results from a study whose objective was to evaluate noise control options for existing equipment used in metal and non-metal processing plants. This equipment performs 3 basic functions, crushing, grinding to a point where the product can be liberated from the waste, and agglomeration A the product. Specifically, the study was directed towards taconite processing since the extreme hardness of taconite results in high noise levels and in considerable maintenance of the processing equipment. Both of these factors make this process a very challenging noise control task. Plants processing other ores use similar equipment, consequently the results of these studies should he applicable to a wide variety of plants. The report presents the source diagnosis and potential retrofit noise control treatments for fine screens, mills, crusher sizing screens, and vacuum disc filters. Estimates are make of the noise reduction from each treatment. The report concludes with recommendations for future research on each piece of equipment.

Jan 1, 1978

By Phillip Allender, Wolf Karo, Knox Van Dyke, Lixin Wu, Ali Ardekani, Jorge Garcia, Jaime Gutierrez

"We report that two different micropolystyrene round beads linked to either luminol or lucigenin have been developed. The 1-µ.m-diameter beads arc useful reagents that allow one to perform chemiluminescent (light producing) phagoeytic reactions without opsonization. It is known that luminol reacts with peroxidases (e.g., myeloperoxidase) while lucigenin reacts mainly with superoxide anion. Luminol and lucigenin beads produce cellular chemiluminescence (CL) with neutrophils, macrophages, monocytes, and differentiated human promyelocytic leukemic cells (HL60). When myeloperoxidase (MPO) is present luminol beads evoke higher CL from neutrophils, but when little or no MPO is present, lucigenin beads produce higher amounts of light. Lucigenin beads appear to be active inside these cells where unbound lucigenin does not enter freely.INTRODUCTIONA variety of cells, e.g., neutrophils (Ns) and macrophages (Ms), can engulf foreign particles (1). This engulfing or phagocytic activity is used by the body to kill bacteria and to eliminate foreign particles such as respirable dusts, e.g., coal, silica, or cotton. The neutrophil engulfs or phagocytizes bacteria which are coated with plasma antibodies and/or complement proteins (Fig. 1). The coating or opsonization allows the neutrophil to recognize foreign substances. Usually the absence of opsonization prevents the cell's recognition of a foreign particle and the particle is not phagocytized. Macrophages, particularly the alveolar Oung) cells, do not require opsonization for phagocytosis. Ms should not be selective toward individual dusts because they serve a major role in eliminating a variety of these.Particle size can also be a factor. Usually a particle with a diameter of 0.5-5 µ.m is considered in the respirable range. Larger particles are trapped before they reach the alveoli Oung spaces where oxygen exchange with blood occurs), ·and smaller particles do not generally settle, and are not engulfed by macrophages (2). Tabato and Ikada (3) found that maximal phagocytosis of microspheres takes place when their diameter is in the range of 1.0 to 2.0 µ.m. In addition, they found that beads with hydrophobic surfaces were more readily phagocytized than hydrophilic surfaces."

Jan 1, 1990

By Nicholas T. Zilka

Mineral resource studies by the Bureau of Mines indicate three areas within the Selway Bitterroot Wilderness have mineral resource potential. Regional studies suggest that a granitic stock on the south side of the Wilderness has high potential for a Climax-type stockwork molybdenum deposit (pl. 1, no. 8); but detailed surface investigations failed to recognize a deposit. The Elk Summit area on the north side of the Wilderness contains subeconomic resources of columbium (niobium)-bearing ilmenite in placers (p1. 1, no. 19). Subeconomic silver-copper-lead resources occur in a vein on the northeast side of the Wilderness at the Clift Mine (pl. 1, no. 2-5). The study area has no known deposits of oil and Haas, coal, geothermal resources, or other energy-related commodities.

Jan 1, 1982

By Russel Bohn

The purpose of this study was to evaluate the various techniques far mine roadway dust control. This evaluation included (a) the types of dust suppressants available, (b) the interaction of these products with the properties of the roadway surface, and (c) the costs and performance measures of the predominantly used dust suppressants. Over 30 products were identified having a wide range of effectiveness depending largely on the properties of the road base, subsurface, and wearing surface. The effectiveness of a dust suppressant was also found to depend on the application and maintenance procedures employed. As a result of this investigation five dust suppressants were identified s being predominant in the surface mining industry: Coherex, wetting agents, lignin sulfonate, water, and calcium chloride: An approximate cost-effectiveness analysis, limited by the lack of quantitative field performance data, showed that the five suppressants ranked in the order given above, with water being one of the least cost effective. This report also presents an analysis of applicable federal and state regulations.

Jan 1, 1981

By Guy Ervin, Delwin D. Blue, John E. Conley

"INTRODUCTION Extraction of alumina from various materials, such as low-grade bauxite and clay, by means of a lime-soda sinter has been the subject of a number ofinvestigations (1, 2, 3, 4, 5, 7, 9, 10, 11, 12, 13, 16, 17). 5/ in recent years, Although many of the details of these investigations are lacking, it is believed that there is one difficultly that frequently develops under certain conditions, namely, that of thickening or gelation of the slurry formed during extraction of the sinter. If gelation occurs even to a slight extent* Serious mechanical difficulties result, very low liquor recoveries are obtained, and the extraction step becomes virlually inoperable. Under 'favorable conditions, a solid gel is formed which can only be removed from the equipment with great difficulty. At the Eastern Experiment. Station of the Bureau of Mines in College Park, Md., a study of lime-soda processes was begun in November 1941. This work has included studies on low-grade bauxites, kaolin clay, and nodular diasporic clay. Gelation was most serous with kaolin clay and least with diasporic clay. As a part of the Bureau's investigation, a study was made of the effect of the pertinent variables on gelation. The results permit the selection of various sets of conditions at which gelation will not occur. These data are essential to the final selection of optimum conditions for the over-all process."

Aug 1, 1946

By F. M. Goodwin, John Campbell, G. W. Jones

"INTRODUCTION In cooperation with the Boston Edison Co. and the Boston Consolidated Gas Co. of Boston, Mass., a survey has been conducted continuously since 1929 by the Bureau of Mines to determine the general hazards of combustible gases and vapors in manholes of the Boston Edison Co. The New England Telephone & Telegraph Co. also has cooperated in the investigation, and tests have been made in its manholes from May 1, 1933, to October 15, 1937. Yearly reports. 6/ on the results obtained since the beginning of the survey have been published.The methods and procedure of conducting the survey in 1937 were the same as heretofore."

Jan 1, 1939

By W. D. Mcmillan

Kaolin, or china clay, is the term applied to a group of hydrous aluminum silicates. Because of its purity, light color, and refractory properties, kaolin is used extensively in the manufacture of high-grade ceramic wares and as a filler by the rubber and paper industries. Although there are numerous pottery and enamelware plants in Texas, and large rubber and paper industries; all of the kaolin used in these plants is from other States, There are two known occurrences of kaolin in Texas, namely, the Leakey deposit in Real County and the several deposits of the Medley district in southern Jeff Davis County. An investigation of the Mueller kaolin deposit in the Medley district was undertaken by the Bureau of Mines. Following an examination of this deposit by W. D. McMillan, engineer in charge of the Texas field office of the Bureau of Mines, a proposal was made to investigate the deposit by diamond core drilling.

Jan 1, 1949

By Jose P. T. Agapito

Several underground coal mines currently operating in the Beckley District of West Virginia are experiencing serious roof and floor problems. A significant portion of the estimated two billion tons of coal resources may be lost as a result of these ground control problems. Preliminary studies by the Bureau of Mines indicated that these problems are due in part to a high horizontal stress field. During this contract study, a field program was conducted to quantify the horizontal in situ stress. A total of 14 overcoring sites (using the Bureau of Mines strain-relief overcoring technique) in five mines were drilled producing 53 data sets. Analysis of the data was done to provide in situ horizontal stresses for each of the five mine, and for the district as a whole. Stress data indicate horizontal stresses far in excess of that predicted by theory and in some cases, up to six times the estimated vertical stress. In addition to the field testing, a detailed computer modeling study was conducted using finite element and boundary integral (displacement discontinuity) methods. Verification of in situ stresses was obtained by the models and analysis of various development geometries, mining methods and remedial techniques were conducted. Recommendations for reducing ground control problems and future studies are presented.

Jan 1, 1980

By Irvin Pritts

This report describes the design, fabrication, and testing of a prototype instrument which demonstrates the feasibility of determining respirable coal dust concentrations by light reflectance photometry. Coal dust is collected on a filter and the quantity collected is continuously monitored by reflectance-photometry. Light emission and detection is accomplished by reflective object sensors, which have both light source and detector in one chip. The use of a pulsed light source insures low drift characteristics of the measuring circuitry. The collection of the respirable coal dust on filters facilitates accurate calibration and also allows measurement verification, if desired, by well-accepted, gravimetric methods.

Jan 1, 1981