Search Documents

By Siavoljub D. Maksimovic

The Bureau of Mines, through a cooperative agreement with Duquesne Light Co. of Pennsylvania, field tested a method of using pneumatic stowing of crushed limestone to construct seals in long-abandoned mine openings that were part of an active mine closed shortly before sealing. A total of 13 openings at 11 sites were backfilled. In pneumatic stowing, material is conveyed through a pipeline and into the mine opening under low air pressure. The stowing equipment consists of a power sup-ply, a blower, a feeder to inject material into the pipeline, and a nozzle for directing the placement. Material is ejected from the nozzle at high velocity, creating a high-compaction fill upon impact. The fill material used was well-graded limestone aggregate up to 1-1/2 inches in diameter, with sufficient fines. This fill was modified at five locations by the addition of portland cement, expansive cement, and/or bentonite. The pneumatic stowing method is safer and faster than conventional methods, is cost competitive, and eliminates or reduces the exposure of workers to possible hazards since the nozzle can be kept outside the mine opening. The equipment is mobile, but some modifications in the technique would improve performance. The technique was used at remote locations where other methods could not be used without disturbing the environment.

Jan 1, 1982

By W. C. Babcock

This report covers Phase V of .a continuing program to apply a new liquid membrane process called coupled transport to the recovery pf metals from hydrometallurgical leach solutions. During this phase of the program, a membrane system of moderate scale was constructed and field-tested at the Exxon Highlands Mine and Mill Co. site near Douglas, Wyoming. The test unit contained four hollow-fiber membrane modules, each with 100 ft2 of membrane area. In the field tests, about 1000 gallons per day of leach solution was processed. The unit was operated on the leach solution for about 50 days. Leach solution entering the unit contained 100 ppm uranium. This concentration was reduced to about 5 ppm by coupled-transport treatment, and the uranium was concentrated to about 2 wt% as a uranyl carbonate product. Under these conditions, a transmembrane uranium flux of about 2.5 lb/ft2-year was obtained. An economic analysis showed that the cost of recovering uranium from this leach solution via coupled trans-port is about $1.20/lb. At higher concentrations of uranium in the leach solution this cost is reduced. For example, at 1000 ppm the cost of uranium recovery is about $0.30/lb.

Jan 1, 1983

By Albert L. Toenges

A phase in strip mining of bituminous coal is the overturning of the surface of the land. The purpose of this report is to acquaint the operators and others interested in stripping with the work that has been done in certain States to reclaim the surface of land from which the coal has been removed by this method of raining. The preparation of this manuscript follows an extensive study of the subject in the field in the course of which a large number of strip mines were visited. ACKNOWLEDGMENT The information used in the report was obtained through the courtesy and cooperation of the operators of the mines visited, State officials and educational institutions, and others interested in the subject.

Jan 1, 1939

By James E. Bell

Quartz crystals occur on a farm in the vicinity of Laurel Fork, Carroll County, Va., in abundance over a large area, This has been known for several years, but no work had been clone, up to the Bureau of Mines examination in 1943, to determine the amount of crystalline quartz of usable quality. Field exploration was undertaken throughout the month of June 1943.

Jan 1, 1950

By O. C. Blade

Studies on more efficient utilization of petroleum have been made for 50 years by the Bureau of Mines. As part of this work, the Bureau has analyzed thousands of samples of crude oil by its standardized routine method, and many of these analyses have been published, sometimes in special compilations, other times in connection with reports of research on petroleum. This report is a finding index for all analyses published from 1921 to 1959, and brings up to date the information in Information Circular 7470 3 and in the appendix of Bulletin 490.4 The routine method of analysis and the equipment originally were described in a report by Dean and associates. 5 This report has long been out of print, but Bulletin 490, bringing the procedure and its modifications to date, was published in 1951. 6 Briefly, the procedure consists of testing, by standard methods, small samples of a crude oil for gravity, sulfur, color, viscosity, pour point, and (more recently) nitrogen; and, by a standardized procedure, distilling a portion of the crude oil and determining certain properties on the separated fractions and residuum. Careful records are made during the procedure, and the distillation data obtained are used to compute the approximate amounts of products present in the sample--such as percentages of gasoline, kerosine, gas oil, and lubricants. The principal data and results are recorded on a standard analytical report form. An analysis of a sample of crude oil from a recently developed field is shown in table 1. Compilations of these analyses, sometimes in tabular form and usually for specific geographic areas, are published from time to time. Analyses often are included in connection with other studies, such as engineering field reports.

Jan 1, 1959

By Robert P. Bruno

This report covers the study of the feasibility of using a hand-held infrared viewer as a methane indicator to observe methane gas at the face of an underground coal mine. The objective of this program was the development of a hand-held device to remotely detect the presence of concentrations of methane gas in underground coal mines. Convenient "mapping" of methane from a remote location would allow rapid and safe corrective procedures for working personnel. Modified commercially available equipment was evaluated both in the laboratory and in a working mine. Although readings were obtained and the general principle of operation demonstrated, the power levels necessary, and protective enclosures required, would raise the weight of the instrument beyond practical limits of portability. Based on currently available technology, it is the conclusion of the investigations that a practical, portable, hand-held visual methane indicator is beyond the state-of-the-art. The recommendation was, therefore, made that work be suspended, and the results and data compiled and presented in a final program report.

Jan 1, 1979

This study of underground mine water inflow was initiated by the U. S. Bureau of Mines in March 1980. The objective of this study is to evaluate the hydrologic variables associated with surface water and ground water systems that affect the inflow of ground water into an underground mine. Data collection techniques are reviewed for their applicability for quantifying these hydrologic variables. Innovative techniques are also investigated. Existing analytical and numerical procedures for predicting underground mine water inflow are reviewed and evaluated. Over 300 computer models were reviewed for their applicability to modeling underground mine water inflow. The model UNSAT2 is utilized for modeling inflow to a shaft and tunnel or drift. This model and the techniques developed in this study are applied to two existing mines.

Jan 1, 1982

This publication summarizes, for potential contractors and other interested parties, the research, development, and demonstration contract projects programed by the Bureau of Mines for fiscal year 1980 (October 1, 1979 - September 30, 1980) under its Minerals Health and Safety Research program. The objective of these projects is to provide an ordered and sequenced series of advances toward the Bureau's overall goal of providing the system technology required to create a healthier and safer working environment for the Nation's mining and minerals processing workers.

Jan 1, 1980

By W. H. Schiffbauer

NIOSH has developed an active proximity warning system called HASARD (Hazardous Area Signaling and Ranging Device) for warning workers as they approach known dangerous areas around heavy mining equipment and other dangerous work zones. HASARD is composed of a transmitter and a receiver. The transmitter generates a 60-kHz magnetic field using one or more wire loop antennas. Each antenna is adjusted to establish a magnetic field pattern for each hazardous area. The receiver, worn by the worker, is a magnetic field strength meter. The received signal is compared against preset levels which are calibrated to identify levels of danger. The receiver outputs can include visual, audible, and vibratory indicators and it can also be made to disable machine functions. HASARD was field tested on a Joy 12 continuous miner, a Komatsu 210 M Haulpak, and on a highwall launch vehicle. Slight modifications were made for each application. HASARD provided warnings as designed and proved to be rugged enough to withstand the harshest of production environments.

By John M. Popovich

Disposing of coal mine waste at the surface has been and continues to be a problem which has yet to be resolved within the coal mining industry. A possible solution to this problem is to return the refuse back into the operating underground mine generating the waste material. It is believed that the approach described will provide an inexpensive and pratical solution to the problem. The designed system is installed and operable at the Millers Cove Energy Company, Inc. property in Lee County, Virginia. This system limits surfact facilities to a minimum size. It incorporates state-of-the-art hydraulic transport and backfilling technology and equipment to systematically backfill areas within the active mine. It maximized the benefits of reducing treatment of coal wasts while it minimizes environmental impacts on groundwater. The system approaches the problem in a manner to maximize benefits and minimize risks. The cost of returning coal waste back underground at the Millers Cove site is estimated at $0.67 per ton of marketable coal (1982 dollars), which is slightly higher than their surface disposal cost of $0.61 per ton of marketable mat (1982 dollars). The underground disposal costs do not include cost savings that should be realized within the preparation plant and treatment facilities at the surface. Preliminary tests of the system were conducted at the surface; funding restrictions prevented an in-mine trial. Efforts should continue to demonstrate the feasibility of solving the problem of refuse disposal. The installed system and plant at Millers Cove should provide the opportunity to test an underground disposal operation. This report contains guidelines to pursue this opportunity.

Jan 1, 1986

By L. Nahai

Iran's petroleum industry is nearly 50 years old and the oldest in the Near East. According to published figures, Iran ranks third in production and reserves in the Near East. These reserves (including probable reserves) are estimated at 35 billion barrels and constitute about 11 percent of the world's total. Iran is the sixth largest producer of crude petroleum in the world. The 1961 output of more than 430 million barrels was 5 percent of total world out-put for the year. In the same year, Iran ranked fourth among world petroleum exporters, providing 8.4 percent of total world exports.

Jan 1, 1963

By P. A. Rey

Water recycle is an important part of the coal preparation process. This study was directed toward: (1) a survey of current practice and an evaluation of both the solid and liquid components of blackwater, (2) an experimental study of blackwater flocculation, and (3) a fundamental analysis of the flocculation process. The solids contained in the blackwater discharge to the fine refuse thickener of a coal preparation plant were found to contain, on average, 56% coal and 44% mineral matter. The mineral matter was largely illitic clay, while the water phase contained relatively large amounts of S04 and Ca++. Detailed studies were made of both natural and synthetic flocculants and the influence of polymer type and pH on the settling rate, turbidity of the supernatent liquid and sludge volume of the settled solids. More tundamental studies were made that clearly indicate the need for controlled mixing of polymer into the suspension to be flocculated, and the need to evaluate, more closely, the structure of the flocs formed during the process. Research recommendations are given.

Jan 1, 1983

By Choon Kooi Quan

Water availability is essential for mining and minerals processing. To provide government and industry with recent data for water use planning and management, the Bureau of Mines canvassed a number of U.S. producers of nonfuel minerals to determine their water use in 1984. Data were analyzed and compared with previously published data in order to examine historical trends in water utilization in the nonfuel minerals industry and to estimate water requirements in the year 2000. Total water use in the domestic nonfuel minerals industry during 1984 was estimated at 2,267 billion gal, of which 571 billion gal was new water and 1,696 billion gal recirculated water. The largest users of water were the phosphate rock, iron ore, copper, sand and gravel, and crushed stone industries, together accounting for almost 90% of total used. More than one-half of all water was used in Florida, Michigan, and Minnesota. In the year 2000, total water use will amount to an estimated 2,679 billion gal, of which 810 billion gal will be new water and 1,869 billion gal recirculated water. Most of this water would be used in producing the foregoing suite of minerals,

Jan 1, 1988

By Rudolf E. Greuer

This report contains the practical application of a computer program for the simulation of ventilation systems under the influence of mine fires and other emergencies on five hardrock mines. The introduction describes the need for such a program, its basic features, and the range of its applicability which is mainly a function of the available ventilation data. The second chapter discusses program modifications, whose necessity or desirability was, during the application, discovered. The following five chapters, which comprise the major portion of the report, give the detailed description of the program application on the five mines. For every one of the selected mines, the ventilation system, the source of the used ventilation data and their preparation for computer simulations are outlined. Based on data for the airflow distribution solely, fumes concentrations in the mines are calculated for several assumed fire locations. Based on data for airflow and pressure distributions, ventilation disturbances caused by fires as well as the resulting fumes concentrations and temperatures are determined. The consequences for escape routes and the possible means to keep them free of fumes are discussed. To investigate the capabilities of the program, other contaminant sources and other potentially dangerous ventilation factors, like fan failures and changed surface temperatures, are simulated also. The results of the calculations have been entered into ventilation plans which makes them easier to scrutinize. All significant computer printouts have been attached.

Jan 1, 1981

By Harold A. Watson

A method for measuring leakage of vapors into a chemical-cartridge half-mask facepiece during simulated use is described. The respirator, fitted with high efficiency cartridges, is worn in a dichlorodifluoromethane (CC12F2)--air test mixture while a series of timed activities (facial movements, varied breathing, exercise, etc.) is performed. Complementing other tightness tests, this method is useful particularly for studying face fit and the effect of facial movements on leakage. The concentration of CC12F2 within the facepiece is monitored continuously to observe the immediate effect of physical activity on leakage. A composite sample is collected simultaneously in a plastic bag as a measure of average leakage during the 18-minute test period. Leakage, reported as percent, is calculated from the concentrations of CC12F2 within the facepiece and in the test atmosphere.

Jan 1, 1970

By Gordon R. Sima

The contract is concerned with feasibility studies, design and fabrication of a group of prototype hand-held test instruments and machine-mounted test instruments for measurement of electrical shock hazards of mining machines. An instrument for use in open pit mining machine ground wire verification was proposed, developed, built, and tested. This report presents the design and operational theory of the open pit instrument as well as information on the program to improve the original prototype hand-held machine-mounted test instruments.

Jan 1, 1977

By J. L. Holman

The Bureau of Mines, at its Rolla Metallurgy Research Center, has devised methods for separating and reusing the major portion of waste plastics discarded in urban and industrial refuse. Waste plastic concentrates from a local collection drive, recycling center collections, urban refuse pilot plants, and the secondary metals industry were separated into three major thermoplastic families--polyolefins, styrenes, and vinyls--based on differences in density using a Bureau-designed sink-float-elutriation hydraulic separator. Other separation methods and systems such as air classification, jigging, liquid media, screening, and electrostatics were studied. Vinyl plastics contain up to 50 percent HC1. It was found that over 90 percent of the HC1 in vinyls can be recovered as usable hydrochloric acid by pyrolysis at 350° C. The remaining pyrolysis products which had heats of combustion in excess of 12,000 Btu/lb, could become valuable as a future source of energy. A characterization study conducted on eight chopped wire insulation wastes from secondary copper and aluminum processors showed that most wastes contained 2 to 7 percent residual metal and large percentages of vinyl. The residual metal content of some of these wastes was lowered to 0.1 percent and the vinyl portion segregated using various separation techniques. The research also suggests ways in which reclaimed thermoplastics may be fabricated into useful products.

Jan 1, 1974

By Oliver C. Ralston, and others

"INTRODUCTION Investigations of the Nonmetals Division are now conducted at College Park, Md.; Tuscaloosa. Ala.; Seattle, Wash.; and. Norris, Tenn. The last of these was acquired, this year by arrangement with the Tennessee Valley Authority and is engaged in electrothermel research, using power generated by the T.V.A. and. raw materials from that region. In general, the work of the division is concerned with dressing nonmetallic minerals end utilizing the products there-from. Coal, salts, and waters are investigated, and the suitability of apparatus and equipment is studied.As the Metallurgical. Division of the Bureau of Mines makes routine tests of certain nonmetallic ores under prescribed conditions for the public if they are of general interest, the published reports of that division should be read and thus, with the reports of tile Nonmetals Division, the whole field may be covered."

Oct 1, 1939

By M. Troyer

A coal shuttle car equipped with a pulsed laser optical ranging system to provide guidance for an automatic steering system was tested in production coal mining. Test results are presented for the two mines where testing took place, and some operator's reactions are included. Automatic steering control keeps the car cantered in an entry, and automatic turns are made at intersections as signaled by the operator. All other controls-tram, conveyor, brake, etc, remain manual and require operator control. Complete override of steering while in the automatic mode is retained by the operator, who may grab the steering wheel at any time and turn in opposition to the automatic signal by applying about 10 foot-pounds of torque.

Jan 1, 1976

By Russell Levens

A strategy for prioritizing mining health and safety research by evaluating the potential for risk reduction through interventions is proposed. Mining has one of the highest incidence rates of injury and disease found in major industries. The main premise of this paper is that often the best opportunities to reduce these rates are not revealed by retrospective analysis of injury and illness data. Instead, a proactive approach is needed that accounts for risks to specific hazards that can be abated by engineering or behavioral interventions. The process proposed here begins with development of prospective interventions. The degree of reduction in risk to be expected from an intervention then is determined from statistics on the mining worker population, the expected degree of success of the intervention, and the expected change in the severity of injuries resulting from the intervention. Three disparate mining health and safety concerns are presented to demonstrate common problems in assessing risks of injury and illness and describe additional data needs. Information on events preceding injuries and illnesses and more detailed demographic data on the mining work force are needed to analyze injury and illness data more precisely. Detailed information on exposure to specific hazards is necessary to evaluate the potential for an intervention to reduce risk of injury or illness.