Search Documents

By William H. Snyer, Victor A. Sterner

A cache of buried explosives was discovered by ICI Explosives, USA Inc. at one of their sites near Gillette, Wyoming. An intensive investigation conducted by ICI management indicated that nitroglycerin sensitized dynamite might be present. Information also indicated that up to 20,000 pounds of explosives may have been buried.

Jan 1, 1997

By Chantale Doucet, Yves Lizotte, Alan Cameron

A joint Federal Government-Industry research project on the effect of geology on the fragmentation of rock excavated by blasting in underground developments was conducted at the CANMET Experimental Mine, near Val d'Or, Québec. A total of thirteen (13) blasts were studied from November 1994 to February 1995. The analysis of each blast was divided into three stages: pre-blast characterization, including structural mapping, assessment of Rock Mass Ratings (RMR), Tunneling Quality Indices (Q), blast design documentation; blast characterization comprising blast vibration monitoring and analysis; and post-blast assessment comprising fragmentation assessment by digital photoanalysis, calculation of half cast factors and measurements of bootlegs.

Jan 1, 1996

By Janos Foldesi, Calvin J. Konya

The determination of the number of primers necessary to efficiently initiate an explosive column charge is essential to good blasting. If the number of primer is insufficient, the total energy stored in the main charge will not be released. On the other hand, the use of too many primers will be counterproductive and raise the blasting cost. Tests were conducted by the authors to determine the correct priming procedure for a basalt quarry. This paper describes the results of those tests.

Jan 1, 1976

By Richard A. Dick

On August 3, 1977 the 95th Congress passed Public Law 95-87, the Surface Mining Control and Reclamation Act of 1977. This Act created the Office of Surface Mining Reclamation and Enforcement (OSM), which was given the responsibility of formulating regulations to implement the Act. This paper explains the rationale behind the specific provisions of the final blasting regulations, which were published in volume 44, No. 50 of the Federal Register, dated March 13, 1979. The major items covered by the regulations include preblasting surveys, blasting schedules, protection of the public, ground vibration limits, the scaled distance equation, airblast limits, blasting procedures, and record keeping. The regulations are designed to protect the safety and well-being of the public and to protect buildings and structures such as wells, pipelines, and storage facilities from damage.

Jan 1, 1979

By Alday B. Andrews

A computer program called Seiswise that predicts the character and intensity of ground vibration generated by surface blasting operations was developed and field tested. The program uses the time histories of one or more pilot shots in combination with various initiation sequences to construct synthetic seismograms which are examined to select designs that will produce low levels of ground vibration.

Jan 1, 1990

By Mike McGill, Stephen Chung, Dale S. Preece

Cast blasting can be designed to utilize explosive energy effectively and economically for coal mining operations to remove overburden material. The more overburden removed by explosives, the less blasted material there is left to be transported with mechanical equipment, such as draglines and trucks. In order to optimize the percentage of rock that is cast, a higher powder factor than normal is required plus an initiation technique designed to produce a much greater degree of horizontal muck movement. This is a significant change from normal blasting practice where fine fragmentation and sufficient muck movement were the prime requirements to permit efficient excavation.

Jan 1, 1994

By S. J. Dillingham

One of the primary goals of every blaster is to achieve the optimum blast design. Too much focus on efficient design, however, can cloud certain issues and exposures that must be addressed if the entire project is to be considered .successful.. Due to the known human response to blast effects and inherent dangers present in the use of explosives, the potential for the project being delayed or shutdown, or the blaster and associated company being named as a defendant in a lawsuit, is always a possibility. Therefore, the blast design and associated project bid must incorporate sound safety contingences and procedures that address those .what-if. Scenarios that may arise as a result of vibration, flyrock, public relations, and job-site personal safety.

Jan 1, 2002

By Elaine Gorham-Bergeron

CAROM is a distinct element, dynamic code developed at Sandia National Laboratories to calculate the motion of rock fragments during blasting.[1] It has recently been improved to incorporate a mechanism for its elements to mimic non-circular rock fragments. With this option, elements stack and move in ways that are characteristic of irregular boulders of blasted rock. In bench geometry, CAROM has been used to examine the possibility of producing variations in muckpile shape due to variations in detonation-time delays between rows. Surprisingly, the shape of the muckpile was predicted to be insensitive to time delays between detonation of rows of explosive, except where the rock fracturing was affected by the time delays.

Jan 1, 1987

By Keith Orgeron, Tibor Rozgonyi, Graham Mustoe, Vilem Petr

This paper presents the results of an experimental and numerical investigation of the shock wave energy transmission and reflection through boundary layers (joints, fractures) or between inhomogeneous geomedium with different physical properties. The conclusions drawn significantly clarify the dynamic failure mechanics because of shock wave energy transmission and reflection through different rock materials and their jointed interfaces. Thorough studies were performed to document the transient, two dimensional deformation characteristics, the normal and shear stress fields for inhomogeneous geomedium focusing on the influence of the internal geometrical shapes, relative density variations and packing of the grain boundaries.

Jan 1, 2002

By Kamal Wadhwa

Ever since the introduction of Liquid oxygen explosives in India in 1927, these explosives are being extensively used in the various mining industries such as coal, ironore, limestone, bauxite, magnesite etc. The earlier LOX compositions were based on cellulosic material of Weberlox series of French origin. They contained the basic ingredients of saw dust with an admixture of cork dust, some hydrocarbons and some metallic powders. However, there were some inherent defects in the soaking characteristics of these compositions, in as much as, absorption and retention of liquid oxygen in the cartridges were not properly regulated in the fine pores and in the inter-granular spaces inside the ingredients in a uniform manner.

Jan 1, 1989

By Donald J. Westmaas, Fred C. Drury

The factors affecting the selection and use of exploisves have changed radically in the past three decades. The objective of this paper is to point out considerations which should now be employed by the Explosives Engineer in his selection and use of modern chemical explosives.

Jan 1, 1978

By Geoff Baldwin, Alastair C. Torrance

The use of monitors to assess equipment performance is carried out on a routine basis in many industries. The benefits gained through process control in knowing exactly how the equipment is working far outweigh the initial capital costs of the monitor. In the mining industry several dragline monitors have been developed and installed on equipment through out the world, but to date none has been fully accepted by the industry. This paper describes the use of a sophisticated monitoring system which incorporates an onboard processor to assess both dragline and blast performance. The use of a radio telemetry link for data transfer has removed the need for manual data collection and transfer, leading to a more efficient and powerful system. Significant effort has been put into the development and verification of a dig index to allow blast performance to be objectively assessed.

Jan 1, 1990

By Henry P. Van Ormer

This paper is written to outline the capabilities and flexibility of the electric motor driven oil cooled rotary screw air compressor in construction and mining applications. With the changing economics between fuel and electric power all over the world, the viability of the electric motor is a choice all construction and mining people should be aware of. The advent of large efficient electric motor driven rotary screw compressors have given a great deal of flexibility to the use of these units on many applications not considered before. Examples are given for rotary and percussion drilling, fennels, and underground, sandblasting and "uniting, general uses - shows wheel mounted and skid mounted units.

Jan 1, 1976

This paper presents a brief discussion of three case histories to illustrate several aspects of the question of blasting in or immediately adjacent to concrete. The results demonstrate a need to make dramatic upward revisions in previous criteria, whether it be the standard particle velocity criteria or damage response spectra bounds, - especially those which include conservative upper limits of constant acceleration for the high-frequency portion of the spectrum. It is demonstrated, also, that conventional off-the-shelf blast-monitoring instruments are not capable of monitoring small blasts at close range. Both the frequencies and the levels of effect are beyond the range of such instruments. These case histories suggest further that there is a need to review the applicability of certain wellknown equations of elasticity.

Jan 1, 1980

By Don Larson, Gordon Coleman

The United States Department of Energy, through its contractor Lawrence Livermore National Laboratory, has entered into a contract with Alpha-IRECO, Inc. for the emplacement of approximately 2.9 million pounds of a 50% RX-MD emulsion 50% ANFO blend into an underground chamber for initiation to produce the 12 trillion caloric equivalent of 1,000 metric tons of TNT. The detonation will be closely monitored to determine the characteristics of a large chemical explosion for comparison with data collected from previous like-sized nuclear events in the same location. This data will be shared with former Soviet block countries to facilitate enforcement of the various non-proliferation treaties currently being negotiated between the countries.

Jan 1, 1994

By Roger L. McCarthy, Ali Reza

The use of an ammonium nitrate-fuel oil (ANFO) explosive in the Oklahoma City Federal Building bombing has led to a renewed interest in using additives during the manufacturing process of ammonium nitrate to render it non-detonable. Suggested additives include calcium carbonate, which is already used in some European countries, and mono-ammonium phosphate (MAP) or di-ammonium phosphate (DAP), which are the primary desensitizing agents claimed in US patent 3,366,468, Method for desensitizing fertilizer grade ammonium nitrate and the product obtained, issued Jan. 30, 1968 (Porter, 1965).

Jan 1, 1999

By J R. "Dick" Daniel

Over the past several years, the Hercules Technical Service Group for the Explosives Department has produced a series of programs for the TI59 programmable calculator dealing with explosive application problems. These programs have been made available to both our internal staff and to the Hercules explosives distributor organization. Several of these programs have found good acceptance and wide usage.

Jan 1, 1984

By Calvin Konya, Janos Foldesi

A bridge over a main line railroad system was scheduled for demolition. The bridge was made of reinforced concrete and spanned three mainline railroad tracks which could not be shut down due to blasting or demolition. To further complicate matters, the mainline tracks had high tension power lines running above the tracks, but below the bridge. These high tension wires provided the electricity for electrically powered trains. The tracks could not be damaged or disrupted, nor could the power line be broken.

Jan 1, 1992

By Donald H. Matthews

The usual method of dismantling massive concrete formations with explosives, is to totally demolish the entire concrete structure. If any portion of a concrete structure is required to remain in its original form and retain its structural integrity, the use of explosives is usually forbidden and the portion to be dismantled is demolished by mechanical means, using various techniques and equipment that are tedious and expensive.

Jan 1, 1978

By P Cotton, N Cox

The Brisbane City Council has implemented a program of continual improvement at its Mount Coot-tha Quarry in the heart of Brisbane, Australia. The program has been underway for the past 6 years, and has resulted in very significant improvements in terms of both the cost effectiveness of its operation, and in terms of its environmental impact on nearby residents. The work has included a focus, amongst other things, on blasting efficiency, and has challenged conventional thinking in terms of the size of blasts fired, the frequency of firing, the diameter of blastholes, and the use of bulk emulsion or slurry explosives.

Jan 1, 1995