Search Documents

By Mike Turner

The Otter-Juan mine was closed by WMC Resources? Kambalda Nickel Operations (WMC-KNO) in 1999 due to the combined effects of low Nickel prices and high mining costs. GBF Mining Pty Ltd purchased Otter-Juan Mine from WMC in early 2001 as part of WMC?s disinvestment from the nickel mines in the Kambalda area. Goldfields Mine Management (GMM), (a wholly owned subsidiary of GBF Pty Ltd) re-opened Otter-Juan in May 2001. The Otter-Juan mine is one of the oldest mines in the Kambalda region and is now mining at depths below 1160mbs. Stresses are very high, rock mass deformation considerable, and the mine has a history of serious seismic activity. Orebody widths in the current mining area range from 2 to 2.5m, with dips from 25° to 40°. On taking over the operation, GMM converted the mining method from the previous mechanised drift and fill method to a slot-rise and strip method using hand held airlegs. During the latter years of production under the control of WMC, production averaged around 12000 tonnes per month, with grades of 2.7% and orebody extraction of only 55 to 60%. In the last three years of operation under the control of GMM the mine has produced an average of 12000 tonnes per month of ore at an average grade of 4.2% and with an orebody extraction of 70 to 75%. The mine is now highly profitable with at least another 3 years of reserves remaining at depth. The main benefits of the current method include reduced dilution and increased extraction. In the relatively poor ground conditions experienced this has only been possible using airleg mining, with excavations designed to suit conditions, support to suit rockmass deformations, and with improved extraction sequencing. Other benefits have included improved operating conditions, reduced falls of ground incidents and a dramatic reduction in seismic activity. These achievements have only been possible by stepping back in time and using traditional airleg stoping methods to extract the maximum amount of the orebody with minimum dilution. This paper includes details of the mine history, geology, mining method, seismicity, and support.

May 1, 2004

By Jeff R. Reinson

The Diavik Diamond Mine is producing diamonds from two orebodies, the A154 South and A154 North kimberlite pipes, discovered beneath the waters of Lac de Gras. Innovative dike technology with appropriate water collection and treatment systems allowed Diavik to start open pit mining of the ore bodies in 2002. To allow planning, engineering, and implementation of sufficient water handling infrastructure, reasonably accurate estimates of groundwater inflow quality and quantity over the life of mine are required. Prior to mining, a numerical model using the continuum approach was developed for regional and site wide water management. After approximately two years of mining, groundwater inflows to the pit were found to exceed those predicted by the base case hydrogeologic model. The most likely explanation was flow through Dewey?s Fault zone. As this fault was not explicitly accounted for in the model, a detailed hydrogeologic investigation was conducted to evaluate its geometry and hydraulic properties. A multi-disciplined approach was used and involved core logging, fluid logging, geophysical logging, packer testing, a pumping test, and water quality sample collection. The results of the field investigation were used to update the conceptual and numerical models and to develop a Discrete Fracture Network (DFN) model to address small scale problems such as flow into future underground drifts. The updated numerical hydrogeologic models predict that up to 70 per cent of the groundwater inflow to the A154 N/S open pit is through the relatively narrow fractured rock zone associated with Dewey?s Fault. Consistent with the continuum model, the DFN model predicts that inflow to a drift excavated in Dewey?s Fault will be approximately 10 times the inflow to a drift excavated in competent rock. The DFN model provides a better understanding of the distribution of these inflows on a local scale over the length of the drift.

May 1, 2006

By David G. Almond

"Economies of scale and the variable characteristics of many large ore deposits have resulted in grinding installations having large SAG mills fitted with variable speed drives. Problems associated with effective operation of this equipment has created the need for better operator knowledge of mill load behavior and the need for new instrumentation capable of providing accurate information about load movement and composition. This paper discusses two performance enhancing instruments available to address these needs.INTRODUCTIONThe economic demands of new mining projects has resulted in increased equipment sizes and this is particularly evident in milling where there are now many SAG mills operating in the range of 28’ – 40’ diameter with installed powers of 8 – 22 MW. These mills are designed to process very high capacities of ore daily2 and the variable characteristics of many of the deposits mined results in the need to vary the mill speed during processing to cater for the changes in ore hardness. Mill speed changes often result in operational problems associated with high-energy impacts striking the mill liners reducing energy efficiency as well as degrading the grinding media through breakage, accelerating liner wear and in extreme cases even breaking liners. These operational problems have given rise to the need to have instruments aimed at providing operators with accurate information in real time about the load composition and movement within SAG mills.The original concepts for operating SAG mills were derived from past experience of operation of conventional fixed speed ball mills. However, the relatively stable conditions that applies with fixed speed and constant ball charge in ball mills supports theoretical approaches to the grinding process based on energy calculations such as Bond’s Work Index concept. Later a set of parameters Si and Bij were used for describing load kinetics, but all of these methods neglect the details of load movement and how the energy is actually used inside of the mill. It is now commonly accepted as a basic rule that SAG mills grind by impact whilst ball mills grind by attrition and consequently SAG mills are designed and operated to generate a large amount of impacts by the cataracting load without paying sufficient attention to where these impacts are actually occurring. Many mills are operated on the basis that as long as the mill is consuming the expected power there is little attention given to the class of bodies using this energy and this often results in the inefficient use of energy."

Jan 1, 2005

By Alain Dorval

"''Purification of marine sands from Les Iles-de-la-Madeleine''This paper presents the results of the work that has been done at CRM pilot plant for «Les Silices du Golfe Inc.». Essentially the purpose of this piloting was to demonstrate, on a semi-industrial scale, the process of purification of marine sands from Les Iles-de-la-Madeleine; that had been developed by CRM Process Development Service. This purification is necessary to produce silica suitable for the glass sand and the foundry sand markets.Introduction«Les Silices du Golfe Inc.» is a company who intends to dredge marine sands around the «Les Iles-de-la-Madeleine» coasts. The material will be transported to Gaspesia where electricity, water supply, and a convenient site is available to treat it. A high purity silica intended for glass sand and foundry sand markets will be produced. The objectives of this purification process are to remove organics, calcium, feldspars and iron.Material ReceivedCRM received 50 tons of sand with Si02 varying between 80,6 and 99,3 % (see Figure.1). The highest variations in impurities were the calcium and lost on ignition. We notice direct relation between% SiO2, % CaO and % L.O.I. as you can see on the following Figures 2, 3 and 4."

Jan 1, 1994

By M. A. T. Cocquerel, M. G. Burcher, J. G. Eacott

"This paper is based on work carried out to examine the feasibility of increasing the smelting rate of two oil-fired calcine-charged reverberatory furnaces . Various constraints prevented physical enlargement of the furnaces and so allention turned to the use of preheated combustion air or oxygen enrichment to bring about the required increase in production. As a basis for further calculation, a furnace heat balance is determined using the smelting metallurgy and combustion data for the current operation. Various other operational data are tabulated and compared with similar data from other operating copper smelters.New heat balances are derived for various levels of combustion air preheat at the current smelting rate, and the effects of air preheat on oil consumption, combustion air and waste gas volumes are tabulated. These data are used to demonstrate the level of increased throughput which would be obtained before constraints in existing gas handling equipment are encountered.A similar exercise for oxygen enrichment is set out, with oil consumption, combustion air and waste gas volumes at various enrichment levels tabulated for the current smelting rate. These data are in turn used to demon strate the smelting rate which would be achieved at a practical level of enrichment before waste heat boiler and gas handling constraints are encountered.The energy implications for both cases are summarized."

Jan 1, 1980

By Arthur L. Holloway, James C. Mugford

"The Underground Research Laboratory (URL) is located in southeastern Manitoba, in the Lac du Bonnet granite batholith of the Canadian Shield. It was constructed by Atomic Energy of Canada Limited (AECL) to conduct geotechnical research for the Canadian Nuclear Fuel Waste Management Program, assessing the concept of permanent disposal of nuclear fuel waste deep in plutonic rock.One of the primary objectives of the research program at the URL is to develop a nondestructive rock mass characterization method that can be used during siting, design and construction of a used fu el waste disposal vault. An experimental program was established to assess radar reflection profiling as a technique for fracture characterization in granite. The highly resistive, homogeneous nature of the Lac du Bonnet granite is ideal for the propagation of electromagnetic energy at the radar range of frequencies and water-filled fracture zones act as excellent reflectors because of their contrasting electrical properties.Radar reflection profiling was undertaken to characterize a major fracture zone located between 5 m and 10 m below Room 211 on the 240 m level of the URL. The profiling was done at a frequency of 120 MHz, on a 1m grid laid out on the bare rock floor of the room. Reflectors identified in the analog data were correlated between the profile lines, digitized, and a three-dimensional surf ace for each recognizable reflector was constructed. These surf aces were then compared with data obtained from the examination of numerous cores from adjacent boreholes intersecting the fracture zone. A very good correlation was found between the major radar reflectors and the most intensely fractured regions of the zone. Modelling studies also showed that a series of prominent shallow radar reflectors were caused by a borehole drilled close to Room 211."

Jan 1, 1990

By G. Hausen, H. Micka

"Modern signal and power electronics made adjustable-speed AC drives technically feasible and reliable and economically attractive. Cycloconverters are discussed as a proven technology for mine hoists. \IntroductionUntil rather recent technical and commercial advances in power and signal electronics, DC motors were used almost exclusively for applications requiring continuously adjustable operating speeds and torques. More recently, the significantly higher efficiency and the accordingly lower operating costs of AC motors gained importance. An effective and efficient speed control of AC motors requires the control of AC voltage and frequency. Table 1 shows typical applications of adjustable-speed AC drives.CycloconvertersOf particular interest to the mining industry are cycloconverters for hoist drives. The cycloconverter represents by far the simplest, most efficient and most economical means of converting a constant-voltage, constant-frequency supply into an adjustable-voltage, adjustable-frequency supply as required for the speed control of AC drives operating in the frequency range to half of the utility frequency.Cycloconverters feeding synchronous motors or induction motors are ideally suited for slow-speed direct-coupled drives."

Jan 1, 1988

By Paul Miranda, Corby Anderson

"The Center for Advanced Mineral and Metallurgical Processing (CAMP) has recently obtained a Mineral Liberation Analyzer (MLA). CAMP has utilized the technology for several projects with excellent results. The MLA is able to both analyze size and quantify mineral phases. Therefore, the MLA is becoming the Sherlock Holmes of the mining and metallurgical industry. For this presentation, four projects have been evaluated and data was collected using the MLA. The first project involved tungsten mine. Previous mining practices have yielded poor tungsten results and recoveries. By using the MLA, tungsten mineral phases, along with possible contaminants, were verified and the results used to try to increase overall tungsten recoveries. The second project evaluated a molybdenite/chalcopyrite concentrate with surprising results. The third project is a silver project. Initial flotation scoping tests were performed by attempting to separate silver from gangue material. Because of the poor recovery results (less than 5%), MLA was used to determine possible scenarios for increasing silver recovery. Finally, the last project involves gold evaluation in tailings. For all projects, MLA application results will be presentedand discussed.INTRODUCTIONThe Center for Advanced Mineral and Metallurgical Processing (CAMP) has recently received a software add-on to a scanning electron microscope (SEM) located at Montana Tech. The Mineral Liberation Analyzer (MLA) technology was developed by Dr. Ying Gu of the JKTech Center of the University of Queensland. Since August 2006, CAMP has received and processed over 50 samples. These samples include a total mineralogy of tungsten ore samples, gold tailings, lead zinc tailings pile, molybdenite concentrates, copper concentrates, as well as others. During analysis of these received samples, the technology allows the samples to be quantified mineralogically with some surprising results.For analysis, the samples were initially sieved between 170 to 200 screen sized mesh. This ensures that received samples mineral size is fairly uniform. The samples are then placed into epoxy and allowed to harden. Next, the samples are polished and carbon coated for MLA analysis."

Jan 1, 2007

By Mohamed Ourriban, Stéphanie Somot, Éric Proulx, Jean-Sébastien Marois, Marjolaine Drouin, Paul Blatter, Ahmed Bouajila, Claude Gagnon

"The mining industry has to face increasing restrictions concerning the use of fresh water in Québec and throughout the world. Increasing recirculated water usage could lead to a better control of the quality and the quantity of water supplied to the mineral processing units. Furthermore, it could reduce the volume of waste water to be managed and treated before its release to the environment. However, process water may have a negative impact on mineral processing operations, thereby limiting the incentive for sustainable development initiatives. As a first step into selecting and testing remediation strategies, one of which being blending local waters, a mapping of process water quality (inorganic and organic fractions) allowed to locate zones in an industrial case study where fresh water is introduced into the circuit and to detect dissolution and precipitation zones. A complementary hydro-geochemical modeling study on water blends was also performed showing encouraging results towards the objectives of the project.INTRODUCTION The industry has to face increasing restrictions on the use of fresh water in Québec (Quebec Government, 2009) and throughout the world (Brown, 2003; UNESCO, 2006). The cost for the use of fresh water and for water management is highly variable and case-dependent (from 0.2 to up to 7 million dollars/year according to available private estimations, excluding the capital expenditure). It may be, or may become, significant for any plant; thus, risk assessment is of concern here. Using recirculated water could lead to a better control of the quality and the quantity of water supplied to the mineral processing units. Furthermore, it could reduce the volume of waste water to be managed and treated before its release to the environment. However, process water may have some positive and negative impacts on mineral processing operations (Janssen, 2003; Johnson, 2003; Rao and Finch, 1989). Negative impacts could limit the incentive for sustainable development initiatives. Water management strategies at mineral processing sites are supported both by a strategic plan and a water management plan. The strategic plan includes legal aspects, investment costs, potential benefits and various risk levels (Corder and Moran, 2006; Côte et al, 2006; Evans et al., 2006; MacIntosh and Merritt, 2003; McLellan et al., 2008; Merritt and MacIntosh, 2006; Robinson and Keddie, 2006; van Beers et al., 2007a; van Beers et al., 2007b; van Berkel, 2007). In practice, the strategic plan evaluates technical possibilities and costs of various scenarios, such as for example: bringing fresh water to the plant or recirculating waters, or using blends of both. Two important factors to consider in order to enhance the future production efficiency and to minimise risks are: the durability and the stability of the resource, both from quality and quantity points of view."

Jan 1, 2012

By Seppo Haapamaki

"Since it started production in 1970, Anderson Lake Mine has experienced several radical changes in mining methods as a result of the physical characteristics of the ore zone along with the need for improved productivity. This paper examines the transition from longhole open stoping to mechanized cut-and fill then to vertical crater retreat at Anderson Lake Mine. The reasons for the need to change mining methods is analyzed taking into consideration the impact of such criteria as improved productivity and ground conditions and how these criteria affected the over-all economic viability of the mine. IntroductionAnderson Lake Mine is one of five producing copper mines in the Snow Lake area and is situated approximately 3 km southeast of the townsite of Snow Lake (Fig. I).The mine production rate at Anderson Lake is 700 tpd and all ore is trucked from the mine to the mill located approximately 2.5 km from the mine site . The mine is serviced by a three-compartment shaft sunk to a depth of 3300 ft with level spacings at 175 ft and 150 ft intervals from the 600 ft level to the 3000 ft level. .The shaft was collared in 1965 and, a year later, the hoist and compressors were installed. By 1969, a crusher system had been built and actual production began in 1970. During 1978, production was suspended for the year to allow for 430 ft of shaft deepening."

Jan 1, 1988

By K. L. Murphy, G. Multamaki, P. M. Huck

"A preliminary evaluation, based on existing data, has been made of the implications of placing radium-barium sludge in tailings areas. The study was restricted to a consideration of possible increases in the quantities of radionuclides escaping to the environment through either groundwater or surf ace water, considering the types of tailings treated and the effluent treatment systems currently operating in Canada.IntroductionIn the recovery of uranium from ore deposits, the tailings produced by mine/mill complexes are conveyed to impoundment areas in slurry form. After settling, the supernatant is discharged to the environment together with runoff from precipitation on the tailings bas in. Currently, all operating uranium mines in Canada employ barium chloride treatment to control the release of dissolved radium to the aquatic environment. The dissolved radium in the tailings decant is precipitated with barium chloride, forming (Ra,Ba)SO4, and allowed to settle in ponds or lakes. In some instances, settling tanks have replaced ponds and flocculants have been added to aid settling. Because the Atomic Energy Control Board does not consider the precipitation ponds to be suitable for final disposal of these sludges, acceptable sites must be found. Options which have been suggested for sludge management include underground placement either in worked-out mine areas or in special chambers, or placement in the tailings areas. Conceptually, the latter alternative is attractive and probably would minimize sludge handling. This alternative would be subject to the AECB policy which requires that upon abandonment, radioactive releases from a tailings area must be within present regulatory limits and that treatment to meet these limits should not be required in perpetuity.No quantitative data exist concerning either the effect of physical and chemical conditions in the tailings on resolubilization of radium from precipitated sludges or the fraction of this additional radium which would be released."

Jan 1, 1982

By J. E. Sepulveda, R. Morrow

"The Linear Wear Theory provides a reliable framework for the assessment of grinding media performance at full scale. This theory can be applied for analyzing grinding media consumption rates in any given grinding operation as well as the evaluation of alternative grinding media products, based on actual operational data, correcting for conditions like ore hardness, feed and product sizes, mill power and circuit throughput; all of them unrelated to the grinding media intrinsic quality attributes. A series of Moly-Cop Tools 3.0 applications have been developed to facilitate the calculations involved. Moly-Cop Tools 3.0 is available, free of charge, to all interested parties through the corresponding author.INTRODUCTION Mineral grinding circuit operators recognize the significance of grinding media (balls) consumption on the cost structure of any full scale grinding facility. The effective cost associated with this essential consumable depends on two factors: delivered price and durability (quality) of the grinding media. When evaluating alternative grinding media varieties, there is a well accepted evaluation criterion by which a given media type is considered to be “cost-effective” when its unit application cost – normally expressed in $/ton of ore ground – is shown to be lower than that of a nominal reference condition: Grinding Media Cost = Ball Price x Ball Consumption (1) ($ /ton ground) ($/ton balls) (ton balls/ton ground) Under this criterion, an alternative, higher-price grinding media product could be “cost-effective” if its associated consumption rate is sufficiently lower than the reference media, enough to yield a lower grinding cost, as dictated by Equation 1. For the proper application of the above criterion, evaluators must rely on representative indicators of grinding media quality, ideally independent of most mill operating conditions. In each particular case, ball price is always a known component; however, it is not so evident how media performance (quality) differences amongst alternative product types could be assessed with a reasonable degree of accuracy and precision."

Jan 1, 2014

By Tom C. Palangio

The mining industry has come to rely on imaging devices to monitor and record all kinds of activities. We use them to measure, improve the process, ensure security, increase production and automate machinery. Cameras can be installed in locations most people wouldn?t want to live and be our ?eyes? to record the events at that location. This paper discusses digital imaging, the equipment, methods, techniques and information that can be learned from digital devices used in mining operations. The guy who said ?a picture is worth a thousand words? probably understated it. Images are the perfect way to document conditions before, after and even during mining activities. Today?s wide choice of cameras, camcorders and other digital devices allow us to record most activities and events. The technology is advancing at a high rate. Digital cameras and camcorders are marvels of technology with high resolution optics, compact size, automatic time and date stamp, great battery life, shutters to freeze motion and computers to auto focus and eliminate jitter (image stabilization). Add to this the economical price and ease of use and everyone in this industry should be aware of the possibilities.

Oct 1, 2010

By R. O. Burt, D. J. Ottley

"SYNOPSISRecent developments in the use of the Bartles-Mozley table and the Bartles CTS screen are described for the gravity preconcentration of fine heavy mineral and metal particles present in low grade pulps. The B-M table is a relatively new device used for the recovery of particles of up to 100 micron size down to 5 microns or in the case of gold and platinum, down to 1 micron. The CTS screen is a wet screening device used for feed preparation ahead of the Bartles-Mozley table and will size effectively down to about 300 mesh. Results and operating data for a number of different materials are given including outline flowsheets; the effects of the major variables on the performance of the table are briefly discussed. The potential of the B-M table to treat a variety of different ores, coal, tailings, and waste products are considered. The utilization of the B-M table in association with other unit processes to improve overall results as well as to improve the economics of design and performance of plants are also mentioned.INTRODUCTIONA number of new gravity concentration devices have been developed in recent years for the recovery of fine heavy mineral and metal particles but for reasons which include low capacity, high capital or operating costs, competition from other and better processes, the absence of simplicity or reliability in operation etc., only a few which include the Bartles-Mozley table, have been proved to be of commercial application.The name of the machine is derived from the inventors name, Richard Mozley, who developed the B-M table at the University of Bristol in England. The table was subsequently taken up and patented, world-wide, by the National Research Development Corporation a British government agency. An exclusive license to manufacture the table was granted by NRDC to Bartles (Carn Brea) Ltd. in Cornwall, England."

Jan 1, 1973

Project Details ? Located 420 km northeast of Yellowknife, Northwest Territories ? Jericho kimberlite discovered in 1995 ? Feasibility study showed +3,000,000 carats recovered from 2.6 million tonne reserve ? Nine year mine life ? Approx. 100 person workforce in full production ? First mine for Tahera, First new mine for Nunavut Completed Ambitious Construction Schedule During 2005 o Feb ? Mar/05 Winter road mobilization o Mar ? Dec/05 Pre-stripping, earthworks o Mar ? Apr/05 Camp facility, occupied May 3 o May ? Dec/05 Process plant o Jun ? Dec/05 Maint. shop, fuel storage, power plant o Jan ? Mar/06 Commissioning, start-up o April 2006* COMMERCIAL PRODUCTION

May 1, 2006

By O. P. Garg

"The Iron Ore Company of Canada (IOC) operations in Labrador and Quebec, in Canada, is among the largest openpit mining complexes on a world wide basis. Since the 1981-82 recession, IOC has embarked on a comprehensive cost reduction and productivity improvement program in order to survive in the world iron ore market.This paper will outline the approach used in prioritizing the cost reduction items.IntroductionMuch of the mining industry in North America is in a crisis state. Most producers are operating at production levels well below capacity, some have been merged or sold, while others have been mothballed or closed permanently. For many of us still operating, the future is uncertain. Despite the many cutbacks and closures, there is still an abundant supply of minerals in the world market and there is almost no hope for any relief on price pressures on most mineral commodities in the near future. The Iron Ore Company of Canada (IOC) operates an iron ore mine, a concentrator and a pellet plant known as the Carol Project located in Labrador City, Newfoundland. This concentrator and the pellet plant have the annual capacity to produce 20 million and 10 million tons respectively. A company owned and operated railway links this operation with the dock terminal facilities in Sept-Iles, Quebec.In the past decade the Iron Ore Company of Canada has been one of the largest producers of iron ore products in the world. Its pellets and concentrates as well as natural ores were sold in North America, Europe and the Far East. In 1981-82, sales, particularly in North America, went into a serious decline. For almost 30 years, the gospel IOC preached to employees was ""production, production!"" There were many innovations, and millions of dollars were spent on the biggest and best equipment, on research and development, on training and developing employees."

Jan 1, 1987

By K. Gie Tan, Frank Wright

"Misty Mountain Gold Limited (MGL - TSE VSE, MGLCF - NASDAQ) of Vancouver, owns the Harmony Gold Project located in the Queen Charlotte Islands of British Columbia. The deposit contains a mineable reserve of 2.3 million ounces of gold, at a 1.2 g/t cut-off and an average grade of 2.1 1 g/t Au.Discovered in 1970 and frequently investigated by previous owners, full-scale production has not yet occurred because of the complex metallurgy of the deposit. Recent process studies that were completed in six months at Process Research Associates Ltd. (PRA) of Vancouver resulted in significant improvements to the project viability. The work involved detailed mineral processing studies aimed at achieving a marketable concentrate. An option for bio-oxidation and cyanidation to allow on-site dor6 production was also investigated.The main findings at PRA followed the front-end recovery of finely divided free gold (Au) by gravity concentration. Approximately 20% of Au reported to less than 0.2% of the mass, resulting in a grade exceeding 500g/t Au. The resulting gravity tailing provided a uniform feed for flotation evaluation. The optimization of this step allowed for a reasonable primary grind size of 80% passing (&) 50pm. Efficient slime’s rejection was made possible by flotation at a reduced pulp density, and pre-oxidized sulphides were reactivated with Na,S. The regrinding of the bulk flotation concentrate followed by up to five stages of cleaning resulted in a combined gravity + flotation product of 50g/t Au with 82% recovery in less than 4% of the feed mass.Further studies indicated that the flotation concentrate was amenable also to tank bio-oxidation. At 65% sulphide oxidation the gold recovery improved from less than 70% to 90% by cyanide extraction using CIL (carbon in leach). This compares to less than 45% gold recovery from whole-ore cyanidation in several previous studies. Heap leaching may also be considered for lower grade material. PRA’s methodical approach and consistent results dispelled the uncertainty about predicting the material behavior for the Harmony Property."

Jan 1, 2000

By Paul J. Sylvester, Yeonuk Choi, Mike Nelson, Louis J. Cabri, Mike Tubrett

"The development and characterization of sulphide standards containing as many as seven precious metals has increased the efficiency and comprehensiveness of micro-analyses for deportment studies using laser ablation microprobe inductively coupled plasma mass spectrometry (LAM-ICPMS). Because trace precious metals occurring in solid solution or as sub-micron inclusions in sulphides, arsenides, and sulpharsenides are often heterogeneously distributed, a significantly large number of analyses are required. Using well-prepared samples it is possible for up to 120 analyses per day, far more than by other comparable methods. Examples will be discussed from projects focused on the deportment of Au and the platinum group elements (PGE).INTRODUCTIONBecause gold and the platinum-group elements (PGE) occur as both discrete minerals and in trace quantities in a variety of minerals (mostly sulphide, arsenide, and sulpharsenide minerals), specialized trace analytical methods were developed and applied to determine the deportment of precious metals in ore deposits, requiring sensitivities ranging originally from about hundreds to presently tens of ppb for individual precious metal or less.In mineralogical studies, micro-analytical techniques such as the electron microprobe were first applied to obtain analyses for major elements in about 1959-60, but as the instrumentation improved early attempts for PGE in potential carrier minerals indicated that reasonable levels of detection (LOD) were of the order of 300-400 ppm, depending on analytical conditions, X-ray spectral lines, and mineral matrix (e.g., Cabri and Laflamme, 1976). Eventually, the lowest detection levels by electron probe micro-analyses (EPMA) obtained for some PGE were of the order of 10s of ppm using high accelerating voltage and current for extended measuring time on peak and background (Gervilla, Cabri, Kojonen, Oberthür, Weiser, Johanson, Sie, Campbell, Teesdale and Laflamme, 2004)."

Jan 1, 2010

By X. Yuan

"The processing behaviours of ores such as their liberation characteristics in comminution and their response in separation processes are affected by their mineralogical characteristics. Key ore characteristics which are relevant to processing, such as mineral proportions, mineral grain size, grain shape and mineral associations are routinely measured at the micro-scale in polished section using optical microscopes and SEM-based automated mineralogy systems. The application of X-ray micro-tomography to mineral processing provides the means to quantify these important micro-textural characteristics in three dimensions, removing the stereological issues encountered when measuring volumetric information in two-dimensional polished sections. In this paper we present several examples of ore textures to illustrate where X-ray micro-tomography can be applied successfully to obtain quantitative measures of ore characteristics which are useful in a variety of process modelling applications.INTRODUCTION X-ray tomography has been used as a tool in medicine for some years and is being applied in a wider range of fields including geology, palaeontology and mineralogy. In this paper we present some applications of X-ray tomography in mineral processing applications being developed at JKMRC. The availability of SEM-based automated mineralogy systems such as MLA and QEMSCAN has seen the increased use of quantitative mineralogical data measured in two dimensions in the design, operation and simulation of mineral processing plants. When the ore is amenable to measurement by X-ray tomography this technique can provide quantitative data for characteristics such as mineral grain size, shape, mineral associations and liberation in three-dimensions. The advantage of measuring these characteristics in three-dimensions is that the stereological issues which bias measurements made on polished sections are removed. X-ray tomography also quantifies the location of mineral grains relative to one another in space - a useful descriptor of ore texture. Like many measurement techniques X-ray tomography has advantages and disadvantages when compared to other techniques. One limitation is that the ability of the X-ray tomography system to discriminate between minerals is a function of the X-ray attenuation of those minerals. While the X-ray attenuation of many common minerals is sufficiently different for X-ray tomography to distinguish between them, there are some where the overlap in X-ray attenuation makes discrimination on the basis of this characteristic alone impossible. An example of this would be chalcopyrite and magnetite. However where the ore mineralogy is suitable to apply X-ray tomography, the technique provides some exciting opportunities to explore the relationship between texture and ore processability."

Jan 1, 2012

The #3 Shaft at Brunswick Mine, Bathurst, New Brunswick, Canada, intersects a soft graphite zone just below the 3400 Level. Ground movement within this zone causes the concrete liner of the shaft to be deflected towards the shaft?s interior, affecting the steel framework of the conveyance. In some areas, the clearance between the cage and the liner has been reduced to less than 2 cm, which is a concern. An innovative surface-mounted extensometer was designed in 2008 to monitor potential movements of the shaft?s liner. Four such novel extensometers were installed in the shaft for the surveillance of a particularly critical 3.0m by 5.5m area. This article describes the approach taken to instrument the shaft, the principle of the new extensometer, as well as the performance of the instrumentation following its installation.

May 1, 2009