Search Documents

By A. West, F. Mohammadi

Growing awareness of selenium bioaccumulation has resulted in selenium management becoming an important environmental issue for mining operations. Selen-IX™ is a novel ion exchange based technology developed by BioteQ to provide an effective solution for removing selenium oxyanions from mine impacted water to single-digit µg/L levels. The technology offers significant potential benefits when compared to incumbent biological treatment processes, including substantially reduced capital and operating costs and significantly reduced production of a selenium-containing sludge for final disposal. This paper reviews the key features of the Selen-IX™ process and presents the results of recent pilot testing on selenium impacted water.

Jan 1, 2014

By Wei Huang, Anh V. Nguyen

"Potash flotation is an industrially proven success of flotation of soluble salts, but its collector adsorption mechanism remains elusive. In this paper, specific ion effects in NaCl-KCl flotation with carboxylate collectors were investigated. Flotation recovery and contact angle were determined as a function of brine composition of NaCl and KCl. The experimental results have shown that wettability of KCl and flotation of the soluble salts with laurate collectors were dependent on brine ion composition. Specifically, adding Na+ to brines decreased hydrophobicity of KCl crystals and their flotation recovery. Both KCl and NaCl could be floated with laurate collectors. However, flotation of NaCl was greatly enhanced by adding K+ to brine whereas flotation of KCl was significantly suppressed by the presence of Na ions. The decrease in KCl recovery upon adding Na+ is attributed to the counter-ion binding in the pulp. The flotation recovery enhancement of NaCl in the presence of K+ is explained by two effects: 1) increasing K+ concentration leads to a better dispersion of collector colloids in the pulp and 2) K+ enhances the collector adsorption at NaCl crystal surfaces. The water affinity matching rule can explain the specific ion binding behaviors and supported by the SFG spectroscopic results.INTRODUCTIONPotassium is an important fertilizer. Its primary source comes from potash ores, which are a mixture of sylvite (KCl), halite (NaCl) and many other complex double salts such as carnallite (KCl·MgCl·6H2O), alkali nitrates such as KNO3 and NaNO3, and sulfates-langbeinite (2MgSO4·K2SO4) with water-insoluble minerals such as clay and carbonate minerals. Previously, these salts were recovered with a lengthy hot leaching method, with further crystallization of potassium salts from saturated saline solutions. Selective flotation has been preferred since 1940s. Various collector adsorption mechanisms have been proposed soon after the industrial introduction of potash flotation. These include the formation of the insoluble compound model (Halbich, 1933; Singewald, 1961), an ion exchange model (Fuerstenau and Fuerstenau, 1956), a heat of solution model (Rogers, 1957), the surface hydration model (Schubert, 1988), the surface charge model (Roman, 1966; Miller et al., 1992), the interfacial water structure model (Hancer and Miller, 2000) and the colloid adsorption model (Leja, 1983; Burdukova and Laskowski, 2009). Most of the early exercises attempting to propose a unified rule on collector adsorption mechanisms can be seen as heroic endeavors due to the consideration of a vast number of salts in the pulp including alkali halides, nitrates, and sulfates, even the practically insoluble heavy earth metals. Additionally, several types of surfactants with different polarization features and alkyl chain length have been employed. As for the recent models, due probably to the preferential application of long chain amines as collectors in industrial potash flotation, most researchers are only devoted to collectors with low polarization features like amines and sulfonates (Hancer and Miller, 2000; Du et al., 2014). Collector adsorption mechanisms are therefore proposed based largely on a neglect of carboxylates as collectors. However, carboxylates remain an important collector type in soluble salt flotation systems where both salt minerals can be floated using anionic collectors and cationic collectors. Fatty acid type collectors are still one of the widely used collectors for soluble salt flotation and also one of the first to be applied on an industrial scale for the separation of potash ore (Hernáinz et al., 2003; Titkov, 2004). Here we examine some recent models that are relevant to our study to reveal a long neglected specific ion binding effects in potash flotation."

Jan 1, 2016

By D. H. Schwarz

The performance of proton exchange membrane (PEM) fuel cells depends on catalyst layer composition and structure. Experimental observations reveal that state-of-the-art catalyst layers consist of microporous agglomerates of carbon-supported catalyst sites bound together by polymer electrolyte. In between the agglomerates are macropores which provide pathways for the transport of gaseous reactants. In this work, three-dimensional, multicomponent and multiphase transport computations are performed using a computational fluid dynamics (CFD) code (FLUENTTM) with a new PEM fuel cell module, which has been further improved by taking into account the detailed composition and structure of the catalyst layers using a multiple thin-film agglomerate model. In this model, it is assumed that thin films of polymer electrolyte and liquid water surround the catalyst sites. The results of CFD computations show that transport limitations associated with the thin film of polymer electrolyte and the presence of liquid water in the catalyst and gas diffusion layers have substantial negative effects on PEM fuel cell performance. Also, the results of computations with variable distributions for a given precious metal loading show that, in general, uniform catalyst loading provides the best fuel cell performance.

Jan 1, 2005

By P. J. Dunlop

THE object of this paper is to present a brief survey of the work done and the results obtained in controlling dust at the Hollinger Consolidated Gold Mines milling plant. The plant includes all primary and secondary crushing, grinding, and treatment operations. The major items of equipment are: (1) Underground Crusher Plant 1 48 in. by 60 in. jaw crusher, crushing run-of-mine ore to minus-6-in. Rate: 420 tons per hour (2) Surface Crusher Plant 3 No. 772 gyratory crushers 3 4 ft. by 16 ft. trommel screens 4 No. S gyratory crushers Reducing ore to rninus-172-in. Rate: 420 tons per hour (3) Roll Plant 5 sets of 62 in. bJ: 24 in. rolls 7 5 ft. by 10 ft. v1bratrng screens Delivering a minus-3/16-in. finished product Rate: 420 tons per hour (4) Grinding Plant 4 7 ft. by 15 ft. low discharge grate ball-mills 4 12 ft. reciprocating rake classifiers Rate: 4,800 tons per 24 hours Maximum capacity: S,800 tons per 24 hours

Jan 1, 1939

By Allan R. Punkkinen

Safe extraction of the valued ore resource in the deep levels of VALE Creighton Mine has progressed in a pillar-less fashion using vertical retreat, slot-slash and uppers retreat methods since the cessation of ?cut and fill? mining in the late 1980?s. Sequencing of the panel extraction and filling has been the key to successful exploitation of high stress orebodies at depth. In late 2010, discussions between the Operating Department and Creighton Ground Control revealed an opportunity to evaluate a trial primarysecondary sequence in the west end of the 400 Orebody at the 2340m horizon. To manage the trial primarysecondary project, a high level risk analysis and management of change was carried out to mitigate potential danger. As part of the requirements, an instrumentation project was conducted in the hanging wall and footwall bottomsills of the secondary panel and within the secondary panel itself. The extraction sequence was modeled with Map3D® software, confirming high stress levels with the advance of the primary panel. Enhanced ground support was installed based on modelling results. A key objective of the instrumentation project was to verify support system response to mining and to obtain knowledge in regards to the behavior of the stope. This paper describes the first time that this type of new innovative instrumented rockbolt technology had been used in a hard rock mining environment. Understanding of the physical deformation mechanisms of ground support in response to high stress conditions is the basis for an effective ground control strategy. The data played an important role in subsequent enhanced ground support system design at the mine and importantly, established the fact that the secondary pillar had not totally failed. Subsequent cavity monitor results helped establish that fact.

Jun 1, 2012

By A. Perucho, J. P. Harrison, A. Bedi, L. Alejano, L. Lamas, A. Sofianos, A. M. Ferrero, R. Migliazza, R. Olsson, J-F. Mathier

"In 2010, the Eurocode for Geotechnical Design, EN-1997-1:2004 (CEN, 2004), informally known as Eurocode 7 or EC7, became the Reference Design Code (RDC) for geotechnical design – including rock engineering design – within the European Union (EU). EC7 is one standard within the comprehensive Structural Eurocode suite, which as a whole has been also adopted by a number of other countries beyond the EU. EC7 is thus becoming a key design standard for geotechnical engineering worldwide.As part of the Structural Eurocode suite, EC7 requires designs to adhere to the principles of Limit State Design. However, it is not clear that current rock engineering design practice can satisfy this requirement. In addition, evidence is accumulating that EC7 is currently difficult to apply to, and may even be inappropriate for, rock engineering design. These issues may be due to the fact that the development of EC7 to date took place without any formal input from the international rock mechanics and rock engineering community.In early 2011 under the auspices of CEN (Comité Européen de Normalisation / European Committee for Standardisation), EC7 entered a formal period of maintenance which was aimed at improving the applicability and ease-of-use of the Code. This maintenance cycle will conclude in 2020 with the publication of a revised version of EC7.This paper describes a number of critical aspects for rock engineering in the context of EC7, inparticular the following:– the history of the Structural Eurocodes and the concepts they embody;– the nature of Limit State Design and the challenges and opportunities it poses for rock engineering design;– the formal means by which the Structural Eurocode maintenance cycle proceeds;– the plans currently being developed for improving EC7 with regard to rock engineering design and construction;– the unique and vital opportunity for the entire international rock mechanics and rock engineering community to comment on the Code and make suggestions for its improvement."

Jan 1, 2015

By A. Osouli, B. Moradi Bajestani

"Increase in permeability of rock mass is vital for both petroleum and geothermal applications. Hydraulic fracturing is a common method to create and increase the permeability for production. Due to the complexity of fracture propagation in a naturally fractured medium, understanding the interaction between hydraulic fracture (HF) and natural fracture (NF) is of great importance to optimize the fracturing process. The possibility of interaction between HF and NF is partly a function of orientation. Various scenarios are predictable for hydraulic fracture regarding the intersection with NF such as being arrested by NF, crossing NF or crossing the fissure while injecting water into it. Different parameters such as geomechanical and geometrical properties of surrounding rock mass, the operational parameters such as injection rate and the angle between created hydraulic fracture and natural fracture (approach angle) can affect the result of hydraulic fracture and natural fracture intersection. In this paper, using a series of flow-coupled Distinct Fracture Network (DFN) simulations, hydraulic fractures were analyzed to investigate the influence of the aforementioned parameters on the hydraulic fracture propagating. Results show that the most significant parameters affecting the interaction of natural and hydraulic fracture are orientation of the intersection as well as injection rate. The interaction and fracture propagation in NF and HF intersections are also studied and discussed in detail.INTRODUCTIONThe hydraulic fracture technology has substantially changed the oil, gas and geothermal industries. With the help of this technology, extraction of fossil resources from tight shale reservoirs will be economical, feasible and sustainable. Due to presence of massive oil and gas trapped in these reservoirs, this technology has been the center of attention for the past 40 years (King, 2012). Hydraulic fracturing is the process in which high pressure water is pumped into shale unconventional reservoirs with low to ultralow permeabilities. With this process paths are created in these mediums for delivering oil and gas to horizontal wellbore and increase the surrounding rock medium permeability. Economical and sustainable stimulation of these tight reservoirs is highly dependable on our understanding in regard to fracture propagation in the highly complex rock medium. Hydraulic fracturing process in rock mediums with preexisting natural fractures is more complex because of the high possibility of Hydraulic Fracture (HF) being arrested or deviated by Natural Fracture (NF). Also, HF and NF intersection can influence the required pumping pressure, injection rate, the outcome of horizontal wellbore and the affected geological underground zones. Since the 1950s, numerous studies have been conducted to predict and plan fracture propagation with the help of modeling and simulation methods. Having a thorough and accurate prediction of fracturing process will not only prevent stimulation of unwanted geological zones or pollution of aquifers, but also will improve the efficiency of the fracturing process. Previously, several studies have been conducted in order to investigate and analyze the interaction of hydraulic fracture and natural fracture (Cottrell, Hosseinpour, & Dershowitz, 2013; Doe, Lacazette, Dershowitz, & Knitter, 2013; Shakib, 2013; Zhang & Jeffrey, 2006)."

Jan 1, 2015

By V. A. Leão, M. L. M. Rodrigues, L. C. Sicupira, I. C. B. Rodrigues, T. C. Veloso

Brazilian sulphide ores can contain a significant content of chloride and fluoride, which are harmful to bacteria and thus bioleaching. This work summarizes a four-year research investigation on the effect of fluoride on both bacterial growth and sulphide bioleaching, supported by studies carried out with secondary copper ores. Firstly, the influence of fluoride on the kinetics of ferrous iron bio-oxidation with Sulfobacillus thermosulfidooxidans was addressed. Values as low as 10.0 mg/L F- fully inhibited bacterial growth, although fluoride toxicity could be overcome by the presence of aluminium, which reduced the concentration of hydrofluoric acid through the formation of aluminium-fluoride complexes. This required at least a 2:1 aluminium/fluoride molar ratio, which ensured bacterial growth rate values similar to that observed in the absence of fluoride ions. Subsequently, both batch and column bioleaching with mesofiles (30 ºC), moderate thermofile (50 ºC) or hyperthermophiles (67.5 ºC) of two secondary copper ore samples were analyzed with focus on the relevant effects of fluoride-containing minerals on the bioleaching of such sulphide ores.

Jan 1, 2014

By David J. McDougall

"The production of pig iron, wrought iron bars and castings in Quebec during the 18th and 19th centuries has been so closely identified by historians with Les Forges du St. Maurice on the St. Maurice River a few miles north of Trois Rivieres (Three Rivers), that one is sometimes left with the impression that it was the only iron works that ever operated in the province. There were however, about twelve others, one of which was so completely re-built that it should probably be considered as a separate entity. All but two were constructed after the midpoint of the 1800s, coinciding with the growing Canadian demand for ""charcoal pig"" for railway car wheels and castings for industry, and about half of them were technically, if not economically, successful. The misconception about Les Forges du St. Maurice may have come about either because of its long history of somewhat less than continuous production over a century and a half, or a tendency of Quebec historians to concentrate on events in the French-Canadian milieu, but whatever the reason, the other Quebec iron works have been generally ignored. All but one of the Quebec blast furnaces could be described as ""pre-industrial"" with capacities ranging between three and ten tons per day, the exception being the Radnor furnace built in 1892 with a maximum production of about 35 tons per day and an alleged capacity of 50 tons per day. Until a railway network was completed in the 1880s, the location of all the Quebec iron works except the Grantham Iron works was dictated by close proximity to adequate ore reserves because horse transport was of little use beyond a ten-mile radius. The other essentials of forest resources (mainly soft woods) for charcoal, limestone for flux and water power, were generally available except within a few miles on either side of the St. Lawrence River. Among the dozen iron works established in Quebec between 1732 and 1880, seven used bog iron ore in charcoal-fired furnaces. Five of these, including Les Forges du St. Maurice, were located on or near the St. Maurice River which enters the St. Lawrence River from the north, and two, the St. Francis Forges and the Grantham Iron works were on or near the St. Francis River which enters the St. Lawrence from the south. In a general way deposits of bog iron ore in the St. Lawrence lowlands of Quebec were contained within the limits of the post-glacial Champlain Sea, with many clustered along the flanks of the St. Narcisse recessional moraine which is crossed by the St. Maurice and other near-by streams, and the Drummondville recessional moraine which is crossed by the St. Francis River."

Jan 1, 1999

By J. A. Reid

THE views and observations expressed herein on this old but constantly recurring question are our own, no effort having been made to align them with standard texts. Therefore, while they may find general acceptance amongst fellow engineers, they must stand as personal opinions and as such are open to debate and discussion. In order properly to consider the subject, it should first be 'set in proper perspective. Why are Prospects Examined? Prospects are examined to determine whether they may contain economic concentrations of metals or minerals, the legitimate mining business being run, pretty largely, to make money. Next to food and clothing, modern civilization is based on metals, with which are included in this discussion minerals, oils, and fuels. A constant and increasing demand for the common metals requires the location of replacements for depleted orebodies, while the use and appreciation of new metals brings increasing demand for them. Aluminium is a good example of a metal which has, within recent years, made great progress. Today, we are becoming increasingly aware of magnesium, chromium, tungsten, thallium, and other lesser known, metals.

Jan 1, 1945

By Joseph Bradley

THROUGHOUT this article, minerals used in the paint industry are designated 'pigments'. They may be classified in two groups: (1) Pigments which are used in the state in which they occur in nature, requiring only mechanical preparation. (2) Pigments which require heating or chemical treatment before use, in order to obtain from them a product of the desired quality or shade of colour. They may be further classified according to colour, as follows: White Pigments .-These include calcium carbonate (chalk, marble), gypsum and alabaster, kaolin-or china-clay, and magnesia. However, the white pigments most extensively used are compounds prepared chemically from minerals containing lead, zinc, titanium, and antimony. The white pigments are of particular importance because, not only are they used by themselves, but they also serve as adjuncts to other colours for the production of special shades. Yellow Pigments.-These are mainly naturally occurring ferric hydroxides, as limonite and bog iron ore, or similar. compounds prepared artificially. Brown Pigments .-Pigments of this group are distinguished for their beauty and depth of colour, and many of them are used in the finest of paintings. Familiar names are sienna, umber, and Vandyke brown. They are for the most part ferric hydroxides, containing varying amounts of water; but the group also includes a manganese brown, which consists chiefly of a mixture of oxide and hydroxide of manganese. Red Pigments.-Chief among this group is ferric oxide, known under various trade-names, such as Canadian red, Persian red, etc., and also the much prized and somewhat rare vermilion. The pigment used is either naturally occurring hematite, de-hydrated limonite, or artificially produced red ferric oxide.

Jan 1, 1937

By Geo. D. Furse

"The information that has accumulated regarding the geology of the McIntyre mine is the result of work by several geologists and, as might be anticipated, their conclusions have varied. The writer has been at the mine only a few years and due to wartime conditions has not been able to study and review the mine's geology as thoroughly as his predecessors. Where the writer's conclusions differ from those of previous authors, it should be noted that he has been unable to re-map all the workings in which flow contacts are exposed, but has endeavoured to describe the structure as indicated by the evidence he has been able to observe. He wishes to thank H. G. Skavlem and H. S. Robinson for their constructive criticism of this paper, and McIntyre Porcupine Mines, Limited, for permission to present it. A list of references is appended.The McIntyre mine is in the central part of the Pearl Lake section of the Porcupine gold area. It includes the ""bed of Pearl lake, twenty-two claims to the north of the lake, and the Platt Vet lot to the southeast. It is bordered on the west by the Hollinger and on the east by the Coniaurum property. The chief ore-bearing veins on the upper levels lie very close to the north shore of the lake, but some occur under the lake, and others of lesser importance are found to the southeast. The most important veins are Nos. 3, 5, 7, 10, and 25. Some of the veins extend into the Hollinger. on the west and others cross the east boundary into the Coniaurum. The total production since the commencement of milling in 1912 to the end of March 1947 has been $168,448,218 in gold and silver from the milling of 17,690,963 tons of ore."

Jan 1, 1954

By J. Qi

Based on the commercial steel 42CrMo (4140, SCM440), a new generation of CrMo steel was developed by increasing the content of Mo, adding the alloy element of V and Nb, and decreasing the content of P and S. This new CrMo steel has higher strength of 1500MPa and better delayed failure property. TEM and EDS were used to study the distribution and function of the alloying elements in this steel. A new EELS technique was developed to study the bonding strength of the grain boundary in the steel. The mechanism of strengthening of the new steel has been studied.

Jan 1, 2004

By A. Monballiu, J. A. Martens, Y. W. Chiang, A. Van Audenaerde, R. M. Santos, T. Van Gerven, B. Meesschaert

In this work, bioleaching of non-sulphidic materials by applying chemoheterotrophic bacteria and fungi is studied. It was found that the tested fungus, Aspergillus niger, leached substantially more nickel from olivine than the tested bacterium, Bacillus mucilaginosus. A. niger also outperformed fungal species Humicola grisae and Penicillium chrysogenum in the leaching of olivine. Contrary to traditional acid leaching, the microorganisms leached nickel preferentially over magnesium and iron. On average, a selectivity factor of 2.2 was achieved for nickel compared to iron. This can potentially facilitate postprocessing of the leach liquor and reduce the cost. The impact of ultrasonic conditioning on bioleaching was also tested, and substantial increase in nickel extraction with A. niger was observed. This was credited to an increase in the fungal growth rate, the promotion of particle degradation, and the detachment of the stagnant biofilm around the particles. Furthermore, ultrasonic conditioning enhanced the selectivity of A. niger for nickel, resulting in a selectivity ratio for Ni/Fe equal to 3.5. The chemical resistance of the selected microorganisms to several heavy metal and metalloid (As(III,V), Cd, Cr(III,V), Ni, Pb, Zn) was evaluated. It was found that, with the exception of As(v) and Cd, A. niger has high tolerance to these components. Therefore, this biohydrometallurgical route can potentially be applied to non-sulphidic wastederived materials, such as industrial slags, ashes and sludges.

Jan 1, 2014

The original JKMRC AG/SAG mill model was developed over 30 years ago and has been upgraded a number of times since then, with the current published version being the Variable Rates model that is now over 15 years old. Since this model was developed further enhancements have been derived, some of which are applied in-house and some which have yet to be incorporated. The published and the commercially available model in JKSimMet is currently undergoing a comprehensive overhaul with a vastly extended data base for model evolution and validation. Improvements developed within the AMIRA P9 project, in-house development and a number of collaborative projects, are being incorporated into the upgraded model structure. Enhanced capabilities will include: power-based breakage rates scaling; a far wider mill filling range (from 10% to 40%) that exhibits peak in throughput as mill filling increases; higher ball loads; improved pebble discharge function; improved slurry discharge function incorporating important mill design and operational influences; and the new size dependent breakage function. The model will also be able to accommodate some influence of liner design and multi-component ores (blends of hard and soft components). This upgrade is still a work in progress but substantial changes have been made to date. This paper presents some of the new improvements and their influence on the predictive capability of the model.

Jan 1, 2012

By Etienne Roy Grégoire

Since the early 1990s, the Canadian mining industry has been increasingly defined by the signing of Impact and Benefit Agreements (IBAs) between mining companies and Aboriginal peoples. While these agreements are intended to complement the legal system, they also serve to establish the legitimacy of mining projects and to encourage the harmonious integration of these projects into their social and environmental contexts. Beyond their practical implications, what are the effects of such agreements on the ability of Aboriginal communities to access the institutional space where the authorization of mining projects and the conditions of their implementation are decided? Can we view IBAs as a preliminary step towards the operationalization of the principle of Free, Prior and Informed Consent? This paper aims to explore the potential of IBAs as a sustainable solution to the legitimacy issues that result from the implementation of the formal regulatory framework governing mining activities in this jurisdiction. We highlight what constraints and opportunities the James Bay and Northern Quebec Agreement (JBNQA) engenders for local communities and draw attention to the ways in which the negotiation of the Raglan IBA and the environmental evaluation processes act upon each other. We find that certain structural problems - and problems of legitimacy ? related to mining in Northern Quebec cannot be solved by the sole signature of an IBA, which suggests the need for caution when considering such agreements as a panacea. The Raglan case demonstrates that IBAs, like other modes of regulation relying on the direct interface between companies and communities, would benefit from a stricter framework and more explicit ties with official regulation channels.

Aug 1, 2013

By Nabeel Khan

Annual oil production from the Canadian Oil Sands in Northern Alberta has been rising for several decades, and more ore and overburden are excavated each year from an increasing number of open pit mines. Overburden meeting certain specifications will be used to dam tailings and fill open pits, but the remaining material must be stored in overburden storage structures (OBSS). Well-designed overburden storage structures are more stable and cost less in the short- and long-term. The purpose of this paper is to explore OBSS designs that will be stable yet economical in the short- and long-term. The geological background of the site is briefly discussed, including the effect of each of the main geologic layers (recently deposited till and muskeg, Clearwater Formation clay shales, McMurray Formation oil sands, and the Devonian limestone) on the slope stability of the OBSS. Cost is considered in the analysis when balancing between minimizing costs (steeper slopes) and acceptable factors of safety (flatter slopes), all the while considering the financial consequences of failure. Potential failure planes are identified and probabilistic analysis is conducted on the critical failure surface. The variations in the factor of safety caused by varying pore water pressure, friction angle, and cohesion, are plotted and discussed.

Jun 1, 2012

By C. J. Hall

This paper presents a basic motive column analysis of natural ventilation and shaft resistance, using the density depth diagram. The method makes use of tables showing the state of the air as determined by thermodynamic analysis. Several theoretical examples are given.

Jan 1, 1968

By J. J. Benitez

MIBC (methyl-isobuthyl carbinol) was previously shown to enhance significantly sylvite flotation when used at the stage of preparation of amine dispersions. In this paper Atomic Force Microscopy (AFM) is used to study the effect of MIBC on deposition of octadecylamine (ODA) on the surface of mica. The AFM images indicate that amino terminated, and therefore hydrophilic, deposits of ODA are observed on the mica surface in the ODA dispersions free of MIBC. In the presence of MIBC a methyl terminated (hydrophobic) monolayer is obtained on the mica surface. The transition between the monolayer and bilayer phases is due to the presence of MIBC. Experiments carried out in distilled water reproduced the results obtained from the brine. Working in pure water instead of brine simplifies the preparation conditions and the analysis by AFM.

Jan 1, 2006

By Karl J. C. Harries

"9.1. INTRODUCTIONIn Chapter 5 of Volume I royalties are dealt with and several topics would appear to be duplicated in this Volume. However, Volume I may be looked upon as a general guide, whereas this Volume is a reference volume. It deals in considerable detail with specific provisions and concepts relating to royalties between private parties. This does not, however, mean that Chapter 5 can be ignored. It should be looked upon as a source of general information concerning royalties between private parties and as a negotiating aid intended to give an overview of various topics. You may well find that in its general approach it will lead you to ask a question which, hopefully, will be dealt with in this Volume .It should be remembered that royalty agreements are agreements with a particular focus, and so the concepts set forth in Chapter 1 apply to them. This chapter addresses a few considerations specific to royalties that will usually form part of an agreement rather than a stand-alone agreement.9.2. FORMAT FOR ROYALTY PROVISIONSIn many of the cases where royalties arise, they are adjunct to, or part of, other arrangements. For example, a royalty may form part or all of the consideration to be given to an owner upon purchase of his property, or it may arise if a joint venturer ceases to contribute to the venture and has his interest converted to a royalty.1 It is with such situations that this section primarily deals; if the royalty is contained in an agreement that is singularly, or primarily, concerned with creating it, then it is just a normal agreement.Commonly, by the time the right to receive the royalty arises, at least some of the other provisions of the agreement have been performed and/or become redundant. For example, in an option agreement the royalty will be a continuing obligation of the optionee, usually arising only after the option has been exercised.2 In a joint venture agreement, a royalty will often arise where the interest of a non-participating venturer has been diluted and converted to a royalty, in which case the recipient will usually become a passive party, entitled only to his royalty, and most of the rights that he enjoyed as an active venturer will cease to be effective."

Jan 1, 2003