Search Documents

By Alex Doll, Derek Barratt

"There is a number of comminution tests commonly used in the mining industry. Many of the tests are used for a particular grinding model or mill sizing program and are incompatible with other tests of different models. This paper provides an overview of the commonly used grinding and crushing tests, which models (or practitioners) use a particular combination of tests and draws some relationships between the incompatible tests based on the DJB Consultants Inc. database of projects.Case studies will demonstrate similarities and differences between major mining districts with some comments about homogeneous and heterogeneous behaviour within the grindability results.INTRODUCTIONThere are a number of bench-scale grindability tests in use for sizing and predicting throughput for grinding circuits. Part of the reason for this variety is there are a number of different grinding models in use in the Industry, and those models operate using incompatible test results as input (Doll and Barratt, 2008).By using the database of testwork in the DJB Consultants, Inc. (DJB) Millpower 2000 database (see Table 1), some of the more commonly used tests are compared and relationships will be drawn."

Jan 1, 2011

By Thomas Deschamps

The main objective of this work was to investigate the effect of binder addition on the geochemical properties of surface paste tailings. Nine leaching columns were prepared following different disposal configurations: non-cemented, non-cemented with cemented layers, and cemented .The proportions of cement by total paste weight were between 0 and 1% for a whole column; the maximum amount of cement in a single layer was 2%. The material used was a sulphide-rich tailings coming from a Canadian hard rock polymetallic mine. The columns have been flushed once a week during 30 weeks. The recovered leachates were analyzed for pH, Eh, conductivity, and a wide range of elements. The drainage rates were monitored during the initial disposal as well as after each column flush. The results show that binder addition can improve the whole environmental performances for some of the studied disposal configurations. The disposal configuration consisting of intercalation of three 2% cement paste layers within non-cemented layers (0.66 wt.% of cement for the whole column), and the configuration with 2% cement added only in the two bottom layers (0,44 wt.% of cement for the whole column), showed the best results in terms of water quality and drainage rates.

May 1, 2007

By A. Pratt

Portland cement is primarily used to solidify backfill in underground mine workings and it represents a major cost in mining operations. CANMET-MMSL has invented an alternative binder technology that does not contain any amount of Portland cement and is made using waste materials, such as development rock and smelter slag. The technology has been successfully tested with many types of base metal and ferrous slag. Research conducted in collaboration with several mining operations in Canada has shown that the CANMET-MMSL binder has considerable potential as a replacement for Portland cement in mine backfill. An integral part of the overall mining operation, backfill is used for two main purposes: safety and environmental remediation. Depending on the mining method used, backfill provides a working surface, stabilizes stope and pillar walls, as well as the surrounding rock mass, and controls caving of stope backs. There are several benefits associated with the replacement of Portland cement in backfill, including reductions in (i) the footprint by placement of slag waste underground, (ii) the environmental effects and long term liability resulting from disposal and containment of slag waste on surface such as acid rock drainage, (iii) GHG as a result of reduced Portland cement usage (the production of 1 ton of Portland cement produces 1 ton of GHG), and (iv) the significant costs associated with reduced Portland cement usage.

May 1, 2010

By J. A. H. Church

The report is too voluminous to be considered in detail within the scope of a single paper, so I will confine my consideration of it to the broader aspects, leaving other members to deal with points of particular interest. The method of presentation leaves one with an uneasy sense of prolixity and confusion of thought; the foreword by the Chairman may well be accepted as a true index of the whole. His argument amounts to this: Recognizing at the outset the futility of divided counsels, it was deemed advisable to arrive at unanimity. To this end, some members subscribed to views to which they do not whole-heartedly assent, thus giving weight to conclusions with which they were at variance. Unanimity cannot be qualified-either it exists or is absent-and, moreover, in the text of the Com-mission I can find no word that unanimity is required. Surely it would have been preferable to have a unanimous report covering such aspects as were acceptable to all members, with minority reports by individual members on such other aspects as were controversial, leaving it to the Government to give such weight to the divergent views as the personality of their sponsors might warrant. In the final analysis the value of an opinion varies directly as the personality of its exponent.

Jan 1, 1926

By Corrie Pitzer

Safety performance in many companies and even industries has stalled in the last decade. Accidents rates are improving but more slowly and yet, serious accidents and fatality rates are not: in fact, these rates of more serious incidents have plateaued or deteriorating. In more dramatic cases, organizations that had ?exemplary? safety statistics, suddenly had a catastrophic or multi-fatality event occurring. Popular books such as In Search of Excellence of Peters and Waterman or Good to Great of Jim Collins created many delusional ?secrets? or recipes, to achieve great performance and yet, most of those ?great? or ?excellent? companies have now declined in their performance, some dramatically and some have fallen from grace, like Fanny Mae, a company Jim Collins identified as a ?great? one, that had to be bailed out in the latest financial crisis. These organizations share several ?delusions? about managing a business, and often, these delusions are created by academics, consultants and authors of popular books about (safety) management. More damaging however is that safety management is defined by a set of key practices or axioms: a focus on human error, compliance to rules and regulations, creating consistency of systems and actions, reacting to accidents and incidents and on prevention of those, measuring safety with performance metrics and rewarding employees on those measurements. All of these axioms contain the seeds of destruction, and they create conditions and dynamics that precede the disaster - and ironically, they are all 'good things' we do in safety management. For example, a mere focus on safety in the business, and the measurement of it, create a culture of repression of mistakes and incidents, leading to a situation where the organization knows incrementally less and less of risks and risktaking behaviour - until the day it all coincides destructively! This paper discusses seven such safety delusions and how they impact on the views and safety management approaches. They are: ??The delusion of (risk) control, that risks can actually be identified, analyzed and mitigated. ??The delusion of compliance, that mere compliance to rules will safeguard the business ??The delusion of consistency, that standard operating procedures will ensure safe operations ??The delusion of predictability, that accidents and trends tell us everything about the risks of the future ??The delusion of human error, that people are the weakest link and that it can actually be dealt with through discipline and enforcement. ??The delusion of statistical trends, that safety is measurable with statistics ??The delusion of invulnerability, that we have achieved high levels integrity and capability to deal wit risks. Organizations that suffered catastrophes all share some or all of these delusions and this paper traces how these played a role in many disasters, ranging from the Titanic, Challenger, Piper Alpha, Bhopal, BP Deepwater Horizon and many more.

Aug 1, 2013

By J. Molgaard, J. Masounave, J. Prinsen, P. Beaulieu, G. Huard

"A study carried out on behalf of the National Research Council (NRC) indicates that economic losses due to wear in the Canadian mining industry are in excess of $700 million annually. Severe wear, mainly by abrasion, was identified as the most important wear mechanism in terms of possible savings. One way to reduce losses would be the proper use of databases. A joint project of The Canadian Institute of Mining and Metallurgy (CIM) and NRC (Tribology laboratories at IMRI) has been initiated to create a factual database containing all relevant experience in the area of wear in the Canadian mining industry. As a first step, a prototype covering slurry pumps is being built. This should help to answer many questions, such as the number of people involved, interest from industry, cost vs benefits, etc.IntroductionTribology is concerned with the understanding of the mechanisms of friction, wear, and lubrication.Tribology is concerned with the correct use of materials for interacting solid surfaces, with the interaction of those surfaces with lubricants, with the chemistry, physics and use of lubricants and their additives. It is concerned with the reduction of friction and wear (or, in the case of belts, brakes, clutch plates, and similar devices, in achieving optimum friction with minimum wear) and is concerned with the avoidance of associated failures in machinery.Lubrication is usually the solution to a problem of friction and wear. Yet far from all the problems of friction and wear are solved by lubrication. The wear of grinding rods or shovel track pads can hardly be solved by lubrication, to name just two examples with which mining engineers will be familiar. There are indeed many situations of wear and friction where the surfaces in contact are unlubricated.In part, tribology is a matter of design. A major aspect, however, has to do with the choice of materials, to satisfy external constraints upon the component design or choice. The operating conditions for much industrial equipment, particularly in mining are, often very severe. The development of wear resistant materials, including materials which are applied as coatings, is clearly an important technology from the point of view of tribology."

Jan 1, 1987

By Jessica Barber

Problem ? Mining operations consistently need equipment that is available, and able to perform to its maximum potential ? The most difficult part of a Maintenance Manager?s job is often a lack of knowledge on how long their equipment has to last ? The short term view can lead to interim fixes that accumulate into larger problems ? It is always difficult to justify major overhauls and upgrades when there is pressure to meet mine plan production targets

May 1, 2008

By H. A. Schnell

"The Phase I Mill at Cluff Lake in northern Saskatchewan was designed to accommodate a very specific high grade uranium ore. As this high grade ore was depleted, construction was undertaken on a new mill circuit (Phase 2) to process a more conventional lower grade ore deposit.The Phase 2 Mill expanded the ore throughput to 800 tonnes per day. The new process employs crushing, grinding, leaching, counter—current decantation, solvent extraction and magnesia yellowcake precipitation and drying to produce a yellowcake concentrate.This paper discusses the process decisions required for this expansion and outlines the new mill circuit. Included is a review of the start up in August, 1984.1.,INTRODUCTION The Cluff Lake Uranium deposit is located 720 kilometers north of Saskatoon in northern Saskatchewan. A high grade deposit was discovered in 1970 with the first production taking place in 1980 after lengthy hearings. The original mill (or Phase 1 Mill) was specifically designed to accommodate this very high grade ore for a very limited plant life.Pilot plant work was carried out in 1981 on the other lower grade ores found in the immediate Cluff Lake area. Feasibility and process selection studies were then undertaken as the Phase 1 mill was nearing its end of life. These studies were completed in March 1983 when approval was given to construct the new Phase 2 mill."

Jan 1, 1985

By J. M. Houston

"In October 1982, Rio Algom Limited, purchased a tin prospect near East Kemptville, Nova Scotia, from Shell Canada Resources. This purchase led to the development of the first substantial tin mine in North America. This paper deals with the drillingand blasting operations at Rio Algom, in particular the use of emulsion explosives technology.This presentation describes what emulsion explosives and Heavy AN/FO are, and the support system used to deliver these products to the blast site.HistoryThe East Kemptville mine site was discovered by Shell Canada Resources (SCR) in July 1978. SCR started diamond drilling on the tin prospect in March 1979. After 8220 m of BQ drilling, it was estimated a reserve of 56 000 000 tonnes of 0.165% Sn was present.The property, which is located 54 km northeast of Yarmouth, Nova Scotia (Fig. 1), showed, after a feasibility study that, given an ore treatment rate of 9000 tonnes per day, a mine life of 17 years could be expected.GeologyThe tin deposit of the East Kemptville Mine, occurs in granitic rocks at their contact with metasedimentary rocks. The mineralization is in the form of cassiterite with associated sulphides of copper and zinc. The tin occurs in a stockwork of tin bearing Greisen alteration zones.East Kemptville MineThe mine planned an open pit operation with the first five years being mined at a rate of 14 000 tonnes per day, of which 5000 tonnes will be waste and low grade ore. Eventually, the total mining rate will be 21 000 tonnes per day, including 12 000 tonnes of waste and low grade ore. Figure 2 shows the general layout of the mine site.East Kemptville Chooses Emulsion ExplosivesIn December 1984, East Kemptville Mine awarded the Explosives Division of C-I-L Inc. a contract to supply explosives to the borehole. The system chosen gives East Kemptville the on-the-bench choice of regular AN/Fa, or a high density, Heavy AN /Fa product called SuperAN· or a water resistant emulsion explosive called MAGNAFRAC· for holes that cannot be dewatered.Emulsion ExplosivesAn emulsion is an intimate mixture of two liquids that do not dissolve in each other. Emulsions have contributed to our daily lives in such products as insecticides, salad dressings and cosmetics."

Jan 1, 1987

By Benjamin H. Clark

"For over 50 years, Derrick Corporation has been renowned for its innovative and durable fine screening equipment and screen surface technology. Derrick’s latest innovation, the patented Stack Sizer, offers mineral processors both high tonnage capacity and high separation efficiency on an extremely small footprint.The Stack Sizer is suitable for separations from 6.3 mm down to 75 microns (200 mesh). The Stack Sizer, coupled with Derrick’s patented urethane screen surface technology, offers an extremely economical alternative to hydraulic classifiers, hydrocyclones, and less efficient low volume wet screening systems. Stack Sizers have been used in feed preparation for flotation, spirals, and a variety of jigs. Mineral processors wishing to reduce grinding circuit circulating loads and generation of slimes due to over grinding, thereby enhancing the efficiency of flotation and gravity circuits, now have another technology at their disposal to perform this critical sizing and grade control function.Over 200 Stack Sizers have been installed in numerous mineral processing applications worldwide attesting to the rapid acceptance of this technology. Stack Sizers are currently screening ferrous and non-ferrous metal ores, mineral sands, silica sand, kaolin clay, feldspar, garnet, phosphate, aluminum dross, potash, coal, tantalum, spodumene, niobium, and other rare earth mineral ores.INTRODUCTIONDerrick engineers have long understood and demonstrated the importance of screen width in coupling both high capacity and high separation efficiency for fine wet sizing applications. As opposed to fine dry sizing, where the length of the screening machine is critical for high separation efficiency, introducing slurry feed to screens in a thin and even layer at minimal velocities across wider screen surfaces allows for high capacities and efficiencies, with maximum screen cloth life. This is due primarily to the combination of free liquid and high frequency vibration of the Derrick motors, which allow fine undersize material to pass through the screen apertures. Lacking either of these factors would be extremely detrimental to the screening process. Without the high frequency vibration of the motor, the screen is essentially a low efficiency sieve bend. Without the free liquid to carry fines through the screen openings, the screen is for all intents and purposes a glorified conveyor or dewatering unit, as little or no sizing takes place once the screen is devoid of free liquid. For optimal screening results, Derrick recommends feeding slurry to a screen at approximately 20% solids by volume. Figure 1 shows the Stack Sizer design concept. Note that a single feed point is used to evenly distribute the flow to the five separate feed points."

Jan 1, 2007

By R. Samuels, R. Klimpel

"IntroductionLaboratory and industrial grinding tests have shown that the process of size reduction of metal containing ores can be significantly influenced by chemicals added to the slurry being ground.,The terms grinding aid or grinding additive refer to a substance which, when mixed into the mill contents, causes an increase in the rate of size reduction. The increased rate can be used to grind a higher feed rate to the desired product size or it can be used to produce a finer product size at a fixed rate. Whether the use of a grinding aid is justified in any given situation depends on the cost of the substance versus the improvement of output or product quality obtained with its use.A wide variety of grinding additive mechanisms have been suggested in the general mining literature (1,2,3,4,5,6,7). The prevention of particle agglomeration, slurry cushioning of grinding media impact, grinding media coating, changing the strength of macro porous rocks, and chemical adsorption on flaw surfaces to change bonding forces and surface energy have all been suggested. More recently, some grinding additive work has been carried out (8,9,10,11) which suggests that the use of efficient chemicals to control the fluidity of dense slurries is a viable economic approach to achieve improved grinding rates. These increased grinding rates are achieved with no increase in power to the grinding mills and apparently with no increase in media consumption costs. Unlike much of the previous work with grinding additives, this recent work is accompanied by a rather complete engineering characterization and prediction of performance capability. The chemicals involved were chosen so as to efficiently control the viscosities of slurries under conditions of high shear yet not adversely affecting flotation, flocculation, and other downstream surface chemistry operations."

Jan 1, 1979

By Marc C. Bétournay

Under the requirement to define the economic advantages of using hydrogen fuelcell vehicles, a broadscoped project was initiated to quantify the costs associated with operating fuelcell vehicles and diesel vehicles. While ventilation savings are clearly an advantage for the former, a complete and detailed analysis of this and other operational and capital cost elements was undertaken in order to provide the mining industry with factual information in considering the changeover from one technology to another. This article outlines the results of the investigations to date defining the costs/benefits associated with: capital purchases, operations (electrical/diesel, mine air heating fuel, ventilation, openings, surface and underground infrastructure, maintenance, labour, etc.), delivery of energy, regulatory obligations, and mine production. Considerations are given to the type and size of a mining operation, the depth, and location in North America. Significant ventilation power, equipment and infrastructure savings are possible with the application of fuelcells for shallower mine applications. At depth, where heat is an issue, there is a reduction in benefit. Specific qualifiers such as minimum air velocities, dust dilution, shaft and heating system velocity limits must be considered on an individual mine basis. While the capital cost for fuelcell mining equipment is currently higher than diesel versions, the high cost of fuelcells is anticipated to be reduced significantly in the near future with the intensification of manufacturing. In either case the operational savings would probably be sufficient to balance the supplementary capitalization costs. A comprehensive cost-benefit report will be issued in the near future.

May 1, 2003

By W. K. Gummer

"THE LOCATION of Canada's present aluminum industry is determined by availability of hydroelectric power, and ready access to ocean transport facilities. The chief raw material for the production of the metal is imported by ship over several thousand miles of water. In times of freedom of shipping and uncontested movement this provides the industry with its cheapest method of operation. However, during the early part of the last decade the general conditions of ocean and rail transportation were such that interest in the treatment of materials other than bauxite was greatly stimulated. This was the case not only in Canada, of course, but in most other countries.Canada has no deposits of bauxite and much research was carried out on other aluminous materials, chiefly silicates, in an effort to develop more or less economic and feasible methods of treatment. In the United States, this research was considerably more extensive. Some projects were early shown to be of little or no value, whereas others, including the widely publicized lime-sinter and soda-lime-sinter methods, became important. In North America, however, apart from the application of the sinter method to the hitherto waste-product (red mud) of the normal Bayer plant operation, none of these processes contributed appreciably to the production of aluminum during the war. In certain European countries, on the other hand, largely because of their situation with regard to bauxite deposits, they had a more general application, and Germany, for example, produced alumina from clay, ashes, and slag by at least four methods."

Jan 1, 1952

By Paul Harvey

Following initial discovery in 1991, BHP Billiton Diamonds Inc opened Canada?s first diamond mine, the Ekati Diamond Mine TM (Ekati) in the Northwest Territories on October 14th, 1998. Four short years later on November 29th, 2002, saw the opening of North America?s first underground diamond mine - the Koala North mine. Nestled between the original Panda open pit and the new Koala pit which is in the early stages of production, Koala North represents the only underground kimberlite mining venture in arctic conditions outside the new underground mines being developed by ALROSA in the Yakutsk region of eastern Russia. Extensive underground kimberlite mining has been practiced in the Republic of South Africa for much of the 20th century and continues today. Underground mining represents a key component of the long term business plan for the Ekati. As various open pits reach their economic limit, continued recovery of high value ore at depth is dependent upon the ability to productively mine the kimberlite pipes by underground methods. As a function of its location, size, and value, the Koala North pipe is ideally positioned to host the first underground mine at Ekati . In addition to being a production source for the operation, Koala North is designed as a learning mine, from which to gain valuable experience in preparation for the potential mining of other larger, higher value pipes by underground methods in the future. Fortuitously Koala North was available for development so the learnings could be integrated into the Panda mine design prior to completion of the Panda pit. Establishing our first underground diamond mine, and applying the open benching mining method in arctic conditions brings a unique combination of mining challenges together in a harsh climate and remote environment. This paper examines the design and establishment of the Koala North mine. Discussion includes experiences gained from the first year of development, production start-up, and provides a brief overview of our potential underground future at Ekati .

May 1, 2003

Experimental Mine, Val d'Or, Quebec, Experiments on the ignition of sulphide dust clouds by explosives have been conducted in a 1 m3 explosion chamber. The explosives tested are ANFO, emulsion, aluminized emulsion and Detasheet. By controlling the composition of the ANFO and the emulsion explosive the oxygen balance could be changed in order to identify the dominant factors in the ignition of sulphide dust clouds by explosives. Experimental results, combined with theoretical calculations, show that the temperature of the detonation products is the most important parameter in the ignition of the dust cloud while the combustible detonation products are of secondary importance in the case of non-aluminized mining explosives. In the case of aluminized explosives and explosives having very negative oxygen balance the ignition of the dust cloud is assisted by the large amount of combustible detonation products.

Jan 1, 1993

By C. O’Hara, S. Roy, K. Swedburg, J. Katchen

"New Gold Inc.’s New Afton concentrator commenced operation in June 2012, producing a copper-gold-silver concentrate. During the first two years of operation, various optimization efforts have improved mill throughput, recoveries and concentrate grade. Daily mill throughput has increased 20% above the design rate. This was achieved through more consistent instantaneous feed rate and size distribution from the mine reclaim stockpile, higher pebble crusher reliability, changes to the SAG and ball mill grinding media sizes, larger SAG grate openings, reduced SAG discharge screen-deck aperture size and an increase in the maximum ball mill power draw limit. Metal recoveries at New Afton are primarily limited by liberation in the coarser size fractions; therefore, improving the grind size at a given mill throughput has been the main means of improving recovery. The average rougher flotation feed F80 size was reduced from 175µm in Q1 2013 to 165µm in Q1 2014, while the average operating mill throughput increased by 25%. Other flotation circuit changes focusing on recovery improvement include the addition of froth crowders to the rougher cells and the use of a stronger frother. The average concentrate grade increased from 22% Cu in Q1 2013 to 25% Cu in Q1 2014. This was achieved by redirecting the flash flotation concentrate stream to the regrind circuit and by the addition of lime to the cleaner circuit.This paper describes the above improvements made at the New Afton mill. The paper describes the objectives, timing and end result of each area of improvement.IntroductionThe New Afton Mine is situated approximately 10km west of Kamloops, British Columbia, 340km north-east of Vancouver. The mine has a moderate climate, access to transportation and electrical infrastructure, nearby fresh water supply, and close proximity to industrial and mining service businesses. The population of Kamloops is around 90,000 with most mine employees living in or around the city."

Jan 1, 2015

In order to maintain a production rate of 6,000 tonnes per day from underground at the Williams Operating Corporation, two independent mining areas were required which created a long narrow sill pillar between them. During initial mining of the sill pillar there were a number of significant ground falls [LeBlanc and Murdoch, 2000] and in March 1999, with no active mining ongoing in the sill pillar area, a rockburst of magnitude 3.0 Nuttli occurred. Extensive ground support was designed and installed to withstand events of similar magnitude [Bawden and Jones, 2002]. A mine wide microseismic system was installed to monitor mine induced seismic behaviour over the entire mine. The area most directly affected by the 1999 rockburst was rehabilitated using a highly ductile support design. Along with microseismic instrumentation, the areas were instrumented using conventional SMART Cables and SMART MPBX?s. Subsequent to this, the area was impacted by a large number of high magnitude seismic events [magnitudes between 1.7 and 3.5 Nuttli]. The ground support performed very well during these events, providing confidence in the mine?s ability to control the ground under severe rockburst conditions. Analyses of microseismic and conventional instrumentation, combined with numerical analyses of sequence alternatives, were used to develop an optimal mining strategy for the sill pillar area. The selected strategy involved utilization of instrumentation data and calibrated model results to analyze yield zones in the sill. The analyzed ?yielded? zones were assessed to be low seismic risk. Initial mining in the sill was then concentrated in these low risk areas, with the objective of further concentrating stress into the remaining seismically active area, in order to induce ultimate failure of the sill. Continuing large magnitude seismicity and resulting damage in the remaining ?high seismic risk? area, led to abandoning a second portion of the footwall access and the strategic decision to extract a stope near the centre of this zone in order to force final failure of the sill pillar. During execution of this plan two large magnitude seismic events occurred resulting in destressing and final failure of the remaining sill pillar. The paper provides a detailed description of this ?strategic mine sequence driven self-destressing process? and the implications to final extraction planning in this area of the mine.

Apr 1, 2005

By V. Coffin, T. Cienski

"(Figure 1) Reagentized pulp enters into the column at about 1/4 of the distance from the top. Inside the column it meets with a downward flowing stream of water and with an upward flowing mass of air bubbles. Flotation takes place in this counter current system while at the same time fine gangue particles are washed off the froth before it reaches the overflow lip at the top of the column. The main operating features of the column flotation are as follows:a) No moving parts. Solids are kept in suspention not by an agitating action of a propeller but by settling down against the rising air bubbles.b) Wash water. Spray pipes are installed a few inches below the froth surface and deliver required volume of water. The purpose of this water is twofold:(i) it keeps in balance the flow of material through the column and(ii) it washes rising froth in the froth layer as well as removes unwanted fines attached to the bubbles at the lower flotation section. As a result the concentrate produced is of higher purity than in the conventional flotation. Column is characterized by very high up-grading. However, even temporary disruption of wash water supply results in a drastic drop of concentrate grate.c) Flow balance. (Figure 2) For the correct operation volume of the underflow (tail) is larger than that of the feed. The difference is made up by the wash water. This difference called bias is predetermined and ranges from some 4 to 15 USGPM depending on the size of the unit and process requirements."

Jan 1, 1981

By Frank van der Meer, Jorge Portocarrero, Alexandra Gruendken

"The number of High Pressure Grinding Rolls (“HPGRs”, also called Roller Press) installations instead of tertiary crushers is rapidly increasing. The technology has been largely accepted in the minerals industry and benefits, such as superior energy efficiency and a lower overall operating cost compared to alternative technologies, have been demonstrated at a number of operations throughout the world.This paper focuses on coarse hard ore operations and reviews the successful installation of the first Roller Press installed instead of a tertiary crusher at the Los Colorados Plant of CMH (Chile) in 1998. It details the experience obtained over the past ten years of operation from commissioning to the present day. It highlights examples of further developments made in the design to improve machine maintainability and availability as well as wear life of the grinding surfaces.A second focus lies on procedures to derive from small scale testing material properties such as wear life, flake formation and strength and their application to industrial size machines to optimize circuit design, especially when Roller Presses are used in closed circuit with screening.INTRODUCTIONRoller Presses (also known as HPGR, High Pressure Grinding Rolls) are considered today state of the art for the preparation of pellet feed. They are also gaining wide acceptance in coarse ore operations. One of the first successful operations in which a roller press was used to replace a conventional tertiary and quaternary crusher is the Los Colorados plant of CMH in Chile.When the Roller Press at Los Colorados was commissioned in 1988, there were 169 Humboldt Wedag roller presses in operation throughout the world. Of these, 14 were installed in the minerals industry. However, these were installed mainly for grinding pellet feed to increase the Blaine value. Up to that time, only three KHD roller presses had been applied for crushing coarse ore in specialized circuits. Moreover, the installation at Los Colorados was the first Roller Press ever to replace a conventional tertiary and quaternary crusher in a hard ore application."

Jan 1, 2009

By Tim Martin, Dave Tahija

"In April, 2014, Hecla's Greens Creek mill, near Juneau, Alaska, switched from sulphuric acid to the use of dissolved carbon dioxide for lead flotation circuit pH control. The Greens Creek mine uses paste backfill, in which mill tailings are mixed with cement and used to fill mined areas. Some backfill inevitably becomes part of mill feed during subsequent mining cycles, resulting in high feed pH levels and increased dissolved calcium in the lead flotation circuit. Sulphuric acid is traditionally used to lower pH in such cases but it produces undesirable side effects, including poorer lead-zinc separation and unstable froth. The amount of sulphuric acid used at Greens Creek was limited due to these effects, resulting in higher than target pHs when feed backfill content was high. Dissolved carbon dioxide can be added without these limitations so pH levels have been under much better control since the switch. Additionally, lead-zinc separation and froth characteristics have significantly improved.IntroductionThe Greens Creek Mine, owned by Hecla Greens Creek Mining is an underground mine located on Admiralty Island near Juneau, Alaska, producing silver, gold, lead and zinc in the form of lead and zinc flotation concentrates and a gravity gold concentrate (McDonald, Morgen & Hancock, 2012). The lead and zinc concentrates are produced in conventional flotation circuits preceded by a graphite removal flotation step.The underground mine utilizes cemented paste backfill, of which a certain amount is inevitably re-mined in later mining cycles and returned to the mill, mixed with fresh ore. The Portland cement used in the paste backfill is highly basic so that, from the point of view of the mill, the net effect is to introduce a good deal of lime to run-of-mine mill feed, producing a very high natural pH. This high pH needs to be lowered to obtain good metallurgical results."

Jan 1, 2016