Search Documents

By R. L. Alexander

"Madawaska Mines Limited, incorporated in 1975 is the successor to Faraday Uranium Mines Limited. The history of the latter's mine development and corporate changes are outlined. This paper describes the geology of the Bancroft area and the rock types found in the mine, particularly the pegmatite which is the host rock for the uranium. The structure, mineralogy and distribution of the ore shoots are described with the method of grade control and mine development. The paper concludes with a summary of the production and mineral reserves.Location, Access, and PropertyMadawaska Mines Limited is located in Faraday Township, Hastings County, Ontario. The mine is in the N.T.S. quadrant 31 F/ 4, Bancroft sheet and near 46 degrees 01 minute latitude, 77 degrees 46 minutes longitude. The mine is one-half mile north of Highway 28, five miles (8 km) west of Bancroft, and is accessible by various highways from Toronto, Ottawa, Peterborough, and Belleville. (Fig. 1). A landing strip for small aircraft is located at the northwestern edge of Bancroft. Bancroft is a modern community with a population of 2,400. The company has the mineral rights to 2982 acres (1207 hectares) surrounding the mine workings and plant which are situated in the north parts of Lots 16 and 17, Concession XI, Faraday Township."

Jan 1, 1986

By W. Beres, R. E. Miller, B. Shiari, L. R. Zhao

A dynamic multiscale (MD/FE) method has been used to study dislocation generation and plastic deformation during a nanoindentation process which is physically associated with the generation of heat within the specimen and as a consequence with a temperature rise. Two different techniques are applied to study the temperature effect on the nanoindention process. In the first technique, a global Nose-Hoover thermostat is applied to the entire atomistic region to keep temperature constant during simulation (finite temperature approach). In the second method, the thermostat is applied only on a damping region along the MD/FE interface. Both techniques are able to effectively and efficiently absorb high frequency reflected waves from atomistic/continuum interface. The temperature profile of the atomistic region beneath the indenter is reported and discussed at four different initial substrate temperatures for both techniques. The loaddisplacement (load/unload) curves for different temperature-controlling techniques are compared and discussed. The nucleation and propagation of dislocations in the atomistic region are investigated for both techniques. Correlations between the observed features in the load-displacement curves with the motion and pile-up of dislocations are reported as a function of temperature.

Jan 1, 2006

By H. Assadi, S. Reutzel, D. M. Herlach

Intermetallics exhibit unique solidification behaviour due to their chemical longrange order. This includes, for instance, generally slow solidification kinetics, and in some cases, an anomalous partitioning behaviour. In the present work the electromagnetic levitation technique - complemented by theoretical modelling - is used to explore various aspects of this behaviour, as observed in solidification of B2 phase in undercooled melts of the Ni-Al system. Moreover, a phase-field model is developed and used to illustrate the effect of chemical order on the solidification kinetics of a B2 phase in a model system. The phase-field model provides an additional basis for the simulation of solidification microstructures in intermetallic forming systems. Both experimental studies and theoretical work signify the role of chemical order in solidification of intermetallics.

Jan 1, 2006

By A. Bendada, P. Servais, X. P. Maldague, C. Ibarra-Castanedo, C. Mohr

Infrared (IR) thermography is a nondestructive, non-contact and non-intrusive technique that allows the fast inspection of large and complex structures with limited accessibility. Pulsed thermography is particularly interesting for the inspection of aerospace materials such as composites given that, after submitting the specimen surface to a thermal front, the most common types of subsurface discontinuities (e.g. porosity, de laminations, dis bonds, fiber breakage and inclusions) can be detected with an IR camera as regions showing abnormal temperature patterns. We present first the case of an aircraft door with water ingress and surface repairs on its honey comb structure. We also highlight the advantages and limitations of thermography for the inspection of aircraft composite parts, such as edge flaps, rotor blades and speed breaks. Finally, we expose some results from a Kevlar® non-planar specimen with Teflon® inclusions at different depths and locations.

Jan 1, 2006

By J .. A. Nemes, I. Ragai

This paper discusses one of the common problems associated with sheet metal forming processes, which is spring back. The materials presented here, stainless steel 410 and Inconel 718, are commonly used in aerospace applications for their superior material properties. Standard tensile tests were performed to determine their tensile properties, as well as material anisotropy. In addition, the effect of anisotropy on springback was assessed experimentally through simple multiple-bending experiments in different directions to the rolling direction. Finally, draw-bending experiments were carried out to study the effect of forming conditions, such as blank holding force, on the final springback angles of the formed parts. For both materials, it was found that the R-values measured for different sheets exhibited variation. However, the specimen orientation does not have a large effect on material tensile behavior or springback angle for simple bending. For the Inconel 718 specimens, the springback angle slightly increases with each stage of deformation during multiple bend experiments. The effect of the blank holding force on springback angles was also examined and found to have a significant effect on thin specimens.

Jan 1, 2006

By A. H. Lang

"The Cordilleran region of western Canada includes most of British Columbia and the Yukon and pares of Alberta and the Northwest Territories. The western part of this region was for about 50 years the principal mineral producing area of the Dominion. It lost this distinction in 1907 when production from the mines of the Canadian Shield took the lead, but it continues to provide about 15 percent of the total Canadian production. In 1945 the total mineral production of British Columbia and the Yukon was valued at $65,302,900, of which about 80 percent was derived from metals.This paper is intended to serve as an introduction co the more derailed Cordilleran papers. Part I includes a brief synopsis of the complex geology and diverse types of mineralization in the region and Parr II collates the main structural principles exemplified in the derailed papers, and draws some conclusions regarding the application of this information to prospecting."

Jan 1, 1954

By M. H. Rana

"A survey of our knowledge in the field of rock mechanics is presented from the viewpoint of applications in the mining industry. Aspects of rock mechanics of special interest to the industry are enlarged upon, with emphasis on the avoidance of over-generalization. The relationship between fundamental and practical rock mechanics is discussed, and the need for cooperation between the university and industry to further our knowledge of -useful rock mechanics is emphasized. An attempt has been made to establish the scope of rock mechanics, as applied to problems in the mining industry. This is brought about by projecting rock mechanics as a tool to be intelligently used rather than magic, capable of producing ""miracles."" Continued education is important for individuals engaged in the application 0f rock mechanics in the mining industry. The scope of this education is discussed from a viewpoint of better communication between industry and the education and/or re-search establishments engaged in this work.Finally, the dangers of over-emphasis on rock mechanics are mentioned, but a justification of the in-vestment in rock mechanics programs in mines is also presented."

Jan 1, 1966

By R. K. Sidhu, N. L. Richards, M. C. Chaturvedi

Nickel base superalloy IN-738LC, strengthened mainly by the precipitation of y' phase, is extensively used in hot sections of land-based and aero gas turbine engines. Fusion welding, which is one of the most commonly used joining techniques for the repair and fabrication of superalloy components, however, finds a very limited application in case of IN-738LC components, as the alloy suffers from HAZ cracking during welding and during subsequent postweld heat treatment (PWHT). The present paper reports on the two methods studied to reduce the HAZ cracking in as-welded and postweld heat treated GTA welded IN-738LC, viz., the use of various fillers during welding, and the use of appropriate heat treatments prior to welding. The results of the microstructural analysis and crack measurements indicated that the HAZ cracking in GTA welds of IN-738LC was significantly reduced by using age-hardenable fillers with Al+Ti concentration less than that in the base metal in conjunction with a preweld heat treatment developed by the authors.

Jan 1, 2006

By X. Cao, M. Xiao, M. Jahazi

Magnesium alloys have low hardness, wear, erosion and corrosion resistance. The repair of service-damaged aerospace components made of magnesium alloys is an attractive solution in terms of time and cost saving. The feasibility of applying laser beam technology to repair ZE41A-T5 magnesium alloy sand castings in the machined surface conditions was studied using a continuous wave 4 kW Nd:YAG laser system. The influence of process parameters such as laser power, cladding speed, wire feed rate and defocusing distance on the shape, size and area of single cladding beads is discussed using a process optimization software. Sound single clad beads with good geometric characteristics were obtained using strictly controlled laser process parameters. The overall results indicate that laser surface cladding using filler wire has the potential for repairing aerospace components made of cast magnesium alloys.

Jan 1, 2006

By M. Jahazi, J. Gholipour

Design and manufacturing of parts using hydroforming process require knowledge about material behaviour and tribological effects during hydroforming. Lubrication is one of the key issues in successfully hydroform the tubes. A Ni-based super alloy tube with 50.8 mm (2 inches) outer diameter and 0.9 mm (0.035 inches) thickness is considered for this research to study the effect of lubricants on the formability of the tubes. Hydroforming of a hollow compressor blade is considered for this project. A combination of press forming and hydroforming is employed to produce the part. LS-DYNA, an explicit dynamic finite element code, is used to model the experiments. Different lubricants are modeled using different coefficient of friction in the model. Predicted results for strain distribution at a critical section of the tube are extracted for each case to evaluate the effect of different lubricants on the process.

Jan 1, 2006

By A. -I. Abenhaim, I. Sasu, C. Perron, I. Mantegh, S. Larose

Manufacturing long shafts, such as those used in turbine engines, normally involves with drilling inside them in order to take the excessive mass out. Concentricity between the shaft axis and that of the drilled hole is very crucial as it impacts the mass distribution around the axis of rotation. It is important that the shaft mass be well balanced around the central axis in order to minimise the centrifugal forces on the bearings and supporting structure as well as any unwanted vibrations. The eccentricity problem, mostly in long shafts, comes due to machining limitations. It is difficult in long shafts to maintain the concentricity tolerances while drilling inside the shaft. In this work, we address the problem of correcting this eccentricity problem, i.e., when the axis of the inside hole deviates from the central axis. The presented work is based on a threepoint bending method and investigates its effect on the residual stresses and plasticity regions induced on the shaft. A full finite element model is presented that can used to design the solution parameters (bending load, location, etc.) and predict the effect. Limited experimental results are also presented to validate the finite element modelling.

Jan 1, 2006

By J. Ipinza, J. P. Ibáñez, Casas J., S. Cortés

Copper powder generated during the treatment of electro-metallurgical bleeds by reactive electro- dialysis (RED) had totally reduced the content of ferric ions in acidic synthetic electrolytes (Cu (II)- Fe (III) – H2SO4). In batch and columnar experiments 100% of the ferric ions were reduced to ferrous ions with an extremely high kinetics. A preliminary conceptual design for reducing ferric ions based on an integrate RED- Column for treatment of electro-winning bleed system is discussed. This system is able to recover simultaneously sulfuric acid and copper powder, which will reduce ferric ions. INTRODUCTION It is well known the negative effect of ferric ions in the copper electro-winning process. The increase of ferric content in the electrolyte reduces the current efficiency, i.e., there is an increase in the energy consumption, and changes the surface morphology of the copper deposit (Das, Gopala & Krishna, 1996; Vargas & Parra, 2013). The increase of the specific energy consumption due to the loss of current efficiency occurs by the reduction reaction of ferric to ferrous ions in the cathode, at the anode the ferrous ions are slowly oxidized to ferric ions (Shaw, Dreisinger, Lancaster, Richmond & Tomlinson, 2004). To control the level of iron in the electrolyte, bleeds are needed; this bleed electrolyte containing copper, sulfuric acid, cobalt, iron and other impurities normally is waster, which increased the production cost of the plant (Milbourne, 2002; Mckevitt & Dreisinger, 2009). Then, permanent efforts oriented to treat those bleeds to avoid losses of valuables components are made; among them are use ion exchange resins (Shaw et al., 2004; Mackevitt et al., 2009), chemical precipitation (Izadi, Mohebbi, Amiri & Izadi, 2017) and electrodialysis (Cortés, Ipinza & Ibáñez, 2013). The last one allows to the simultaneous recovery of sulfuric acid and copper powder. If one of the valuables obtained by treating the bleed can be used to reduce ferric ion concentration in the electrolyte could be an important asset. This issue at laboratory scale is reported in this work, the use of copper powder, generated by reactive electro-dialysis when treating synthetic acidic electro-metallurgical bleeds, for reducing ferric ions in acidic electrolytes.

Jan 1, 2019

By Michele L. Kimble

A fast-flow reactor mass spectrometer has been utilized to investigate the reactions of gas-phase gold cluster anions with CO and oxygen. Addition of CO to Aun - produces species of the form Au(CO)m -, where m = 2-5. However, CO does not bind to Au2 - or Au3 -. With oxygen addition in the cluster source, gold oxide species with both molecular and atomized oxygen are produced. The addition of carbon monoxide to these preoxidized gold cluster anions reveals that select species with 1, 2, and 3 gold atoms participate in the oxidation reaction to produce CO2. Bimolecular rate constants for the reactions between these species and CO are also discussed.

Oct 1, 2003

By F. Q. Barnes

"Uranium, thorium and yttrium have been recovered, since the 1950s, from pyritic quartz-pebble conglomerates occurring in the basal sediments of the Quirke syncline at Elliot Lake. Gold, an element of interest in similar type deposits occurring worldwide, is a very minor constituent of the Elliot Lake conglomerates because the provenance area of the sediments had few gold-bearing rocks.Uranium, thorium and rare elements are found in resistate and diagenetic minerals occurring in the matrix of the conglomerates. The valuable elements are recovered from the acid soluble minerals during the milling process.Large uranium reserves occur in mines found on both limbs of the Quirke syncline. Major reserves are being developed on the South Limb of the syncline, where the Stanleigh Mine, among four past-producers, has been reactivated.IntroductionUranium and thorium commonly occur in anomalous amounts in coarse basal sediments. Radioactivity in basal conglomeratic sediments is generally attributable to resistate minerals, that rarely occur in concentrations high enough to be of economic significance. One type of basal conglomerate found worldwide, in Precambrian cratonic basins, has uranium or uranium and gold concentrations large enough to be of economic interest. Principal among the occurrences are the pyritic quartz-pebble conglomerates of the Huronian in Canada, of the Witwatersrand in South Africa and at Jacobina in Brazil.The uranium and gold mineralization of these conglomerates was derived from provenance areas where both elements occurred and were later concentrated through source degradation and deposition in placers in a reducing environment. Only the Huronian conglomerates, generally much richer in uranium but with negligible gold, have been exploited solely for their uranium content.The uraniferous conglomerates of the Huronian at Elliot Lake, 500 km north of Toronto, continue to represent a major world source and supply of uranium concentrate."

Jan 1, 1986

By Chris G. Dobson

Introduction The Britannia mine is at Britannia Beach, on Howe sound, approximately thirty miles from Vancouver. The first claims were staked in 1898, and a local company was formed at that time to develop them. In 1904, Mr. Grant B. Schley became actively interested in the property and in the following year the Britannia Mining and Smelting Company, Limited, was incorporated to operate it. This Company was taken over a few years later by the Howe Sound Company, Limited. The mine comprises five more or less separate ore-bodies, which have produced approximately 20,000,000 tons of ore to date. The East Bluff ore-body, with which the present paper deals, is well suited to large-scale mining by means of carefully placed powder blasts. It covers approximately an acre and lies in the slate footwall, in a bay produced by a fault. The hanging-wall side, on the west, forms the face of the Bluff glory-hole, which extends to the 1,200 level. A portion of this ore was available for breaking into this old glory-hole, below which four bulldoze chambers could quickly be built. Mining of this block is complicated by a very soft footwall, which 'runs' badly when broken. In stoping, care is taken to guard against the hazard of dilution by deliberately leaving a small portion of ore on the footwall. Some of this will undoubtedly be lost, but it is hoped to recover a fair amount of it after the major drawing is completed. The deposit occurs in a greenstone which has been highly silicified following brecciation. The chief minerals are chalcopyrite, sphalerite, and pyrite. Concentrates of copper, zinc, and pyrite are made at the mill. The average grade of ore runs 0.7 per cent copper, 1.5 per cent zinc, and 0.03 oz. gold per ton. The rock, which is practically a chert, is extremely hard, but shatters well. Both in stoping and drifting, holes must be closely spaced and powder used generously. Development When development work started in the East Bluff, there were no raises and only one drift on each level in this section of the mine. After blocking out the ore by thorough diamond drilling, a production of two thousand tons per day was set as a goal. To obtain this tonnage from so small an area required a great deal of carefully planned and well timed development work.

Jan 1, 1935

By Q. J. Xu

In blasting sensitive areas, the use of traditional blasting for rock fracture is restricted. Soundless cracking technology has been presented to achieve rock fracture instead of blasting. However, when the diameter of a borehole is larger than 50 mm, it is very dangerous that the soundless cracking agent (SCA) will have a tendency to gush from the borehole, which also leads to cracking failure. In this paper, a new large scale borehole soundless cracking technology is presented, using a new enlarged drill bit and mechanical plugging, which could solve the hole gush problem. Experiments were made to measure the expansive pressure of the SCA working in boreholes of F40 mm and F100 mm. The difference between two sizes of cracking phenomenon was compared and analyzed to show that large scale borehole soundless cracking has larger expansion pressure and faster reaction speed than traditional soundless cracking. Based on the experimental data, finite element analysis was utilized to study the stress concentration and stress distribution between two neighboring large boreholes in several media during the cracking process. Using the data from experiments with finite element numerical simulation, the brittle material fracture condition was analyzed to design the parameters of the borehole mesh. With the theoretical analysis, the technological process and reference parameters of large scale borehole soundless cracking were proposed, including the borehole spacing, burden distance, depth of the borehole and so on. Then a single rock was cracked with the new enlarged drill bit and new plugging, and the results proved the feasibility of the new large scale borehole soundless cracking technology, which achieved the expected goal of improving the cracking ability and reducing the cracking time. This paper presents a new efficient rock cracking method for blasting sensitive areas, and which could apply to mining engineering, demolition engineering, excavation engineering and other engineering applications where there is a demand soundless and non-vibration fracturing of rock.

Aug 1, 2013

By Michael E. Charles, Jaroslav J. Vocadlo

"The hydraulic transport of solids through pipelines can have many advantages over other modes of transport. Numerous successful applications both within plants and over longer distances have demonstrated the technical and economic feasibility of slurry pipelining. Solids successfully transported include kaolin, coal, iron ore, gilsonite and limestone, and others, such as sulphur and potash, are likely to be transported in Canada in the near future. However, though the technology of solids pipelining is quite advanced the underlying principles have not yet been formulated past the semi-empirical stage. The main objective of this paper is to present a discussion of the important technical and economic considerations in the design of so lids pipeline systems by reference to typical data. The Worthington slurry pumps and pilot facilities are briefly described."

Jan 1, 1972

By M. Potesser

In the past, different furnace types have been developed for use within the copper industry, with two common anode furnace designs typically used in copper smelting plants worldwide: the tiltable reverberatory furnace (KPO) generally used for the secondary copper industry and the cylindrical or drum type anode furnace (TRO) for handling a liquid blister charge generated in primary copper production. The disadvantage of the KPO is its design related to the longer refining period, because of the low bath depth, however it provides good conditions in the melting period due to its large bath surface. On the other hand, small amounts of scrap charged into the TRO increase the melting and dissolution period, but it provides good conditions for the refining period. The newly-developed elliptical furnace concept (TRE) offers the advantages of each of these furnace types. The special design allows melting of the scrap more efficiently than in the KPO and refining the liquid copper more efficiently than the TRO. This paper shows a metallurgical comparison of the three furnace types in regard to the melting period by heat technological considerations (optimized arch design) and of the refining period done by CFD with concentration on current, recirculation and dwell time of the gas in the melt. The paper outlines the possibilities for a reduction of the tap-to-tap time and energy consumption as well as for an increase of the production capacity, which can be achieved by applying the TRE instead of the conventional furnace designs.

Jan 1, 2007

By P. Chollet, A Constant

THE RESULTS of a previous investigation ( 1) on the work-softening of some heat-treated steels have led to the conclusion that the occurrence and intensity of the phenomenon is possibly governed by the work-hardening capacity of the material, and the relative amount of retained austenite. The first assumption is compatible with Polakowski's theory (2) that the absence of work-softening, in steels quenched and tempered at relatively low temperatures, may be attributed to the high rate of work-hardening which compensates for, and even out-weighs, the loss of internal energy associated with the simultaneous rearrangement of the original system of internal stresses. Indeed, Polakowski first considered the work-softening as a manifestation of a partial release (by cold-working) of the latent strain energy stored in

Jan 1, 1962

By L. Shasko, M. Hurlbert

As climate change is increasingly perceived as a problem, and fossil fuel based power production options are increasingly limited through regulatory restrictions and public distaste, future options become constricted. Reflexivity and social learning elicited through qualitative and mixed research methods offer important insight into what future power production pathways might be. Given factors of cost, baseload requirements, and energy density, options such as nuclear may be increasingly accepted. This paper explores this literature and possible methods of pursuing the reluctant acceptance of nuclear energy.

Jan 1, 2020