Search Documents

By J. C. Loretto, H. A. Simons

The paper discusses how, in the routine testing of ores, insufficient communication between the laboratory and the design personnel can lead to misunderstanding or misinterpretation of test results and consequent design errors. A number of examples are given together with suggested modified interpretations and the resulting dollar savings indicated by these new interpretations.

Jan 1, 1972

By The Hollinger Mill Staff

MR. E. L. Longmore (l), in presenting this paper at the Annual General Meeting, suggested that it was neither desirable nor necessary to read any but the briefest portion of the paper. He wished to emphasize that the scale of the milling operations at the Hollinger not only provided several units in continuous operation to ensure that the test work was being carried on under normal conditions, but also provided a large and competent staff to supervise such an extensive experiment and to criticize intelligently the recorded results. He wished to acknowledge the enthusiastic co-operation of the group of assistants whose excellent work was responsible for the confidence with which the conclusions could be presented. The following data were given as a supplement to the published paper. Following conclusion of the test work described in the paper, the size of the balls fed to the mill was changed from 3-in. diameter to 2Yz-in. Within a short time, a gradual rise in the tonnage rate took place and, as no other condition had been changed, the increased tonnage was credited to the changed character of the ball load. At present, the average daily tonnage for the mill with low discharge is 1,507 tons, an increase of 77 tons over the 1,430 tons ground when feeding a 3-in. ball. A similar increase in tonnage should be credited to the high-discharge test, if the 2;Y2-in. ball had been used at that time. This would raise the 1,117 tons ground at that time to a new figure of 1,177 tons. From a study made to determine those factors influencing the rate of pulp flow through the low-discharge mill, it became evident that the ball screen used on the high-discharge mill must have been restricting the flow through the mill, although this was not recognized at the time. Accord-ingly, it was decided to repeat the high-discharge run. Additional length was added to the 21-in. ring grizzly originally used, and the length of the reverse spiral was increased. The end of the grizzly was left open so that, if necessary, excess pulp might flow out. A coarse mesh 3 ft. by 3 ft. flat screen was provided to catch stray balls.

Jan 1, 1937

By W. A. Jankola, M. T. Martin

"The world's first zinc pressure leaching plant at Cominco's Trail operations started production in 1981. Sullivan zinc concentrate is leached at the rate of 190 tpd in a four-compartment autoclave at elevated temperatures and oxygen pressures to produce a zinc sulphate solution and elemental sulphur. Zinc extraction exceeds 98% and sulphide to elemental sulphur conversion exceeds 95%.The sulphur is recovered from the discharged slurry in the underflow of a hydrocyclone, and is upgraded as a flotation concentrate. The concentrate is dewatered, melted and filtered to produce a polished sulphur product of better than 99% purity. An alternative sulphur recovery process employs an unique sulphur separation method that recovers over 90% of the sulphur in the molten state. The remaining sulphur is recovered by flotation following flash discharge of the slurry. The product slurry containing the zinc sulphate solution and the iron-lead residue joins the existing roast-leach zinc plant for purification and zinc electrowinning.IntroductionIn 1981, Cominco Ltd. commissioned the world's first commercial zinc pressure leaching plant at their Trail operations in British Columbia. As part of a $700 million modernization and expansion program for lead and zinc started in 1977, the company installed the first o f two autoclave trains.Prior to pressure leaching, zinc production was closely tied to acid and fertilizer production. Sulphur dioxide produced from roasting the concentrates had to be converted to sulphuric acid. Thus, any expansion of zinc operations with the roast-leach technology would have required extensive modifications to the acid and fertilizer plants as well as to the roasters. Zinc pressure leaching, on the other hand, offered a one-step dissolution of zinc from the concentrates with high extraction, and production of elemental sulphur. The associated dust and sulphur dioxide generated in the roasting process are both eliminated from the working environment of the pressure leach facility. The flexibility allowed by producing elemental sulphur, and the opportunity to break the sulphuric acid link for about 25 per cent of the targeted 272,000 tonnes per year zinc production was very appealing. The process was successfully demonstrated at a pilot plant in 1977(1-6)."

Jan 1, 1985

By Franz Xaver Spachtholz

K+S Potash Canada GP (KSPC) is part of the K+S Group, one of the world's leading suppliers of standard and speciality fertilizers and the world?s leading salt producer. Globally, the K+S Group employs more than 14,000 people. The K+S share ? the only commodities stock on the German DAX index ? is listed on all German stock exchanges. Legacy, K+S Group?s most recent project, is a greenfield solution potash mine and production plant in the south of the Canadian province of Saskatchewan. Therefore K+S will invest 4.1 billion CAD. With the expected commissioning in summer 2016 the company projects to reach the two-million-tonnesmark of production capacity at the new location at the end of 2017. The gradual extension of the annual capacity to 2.86 million tonnes of potash products will occur afterwards. The Legacy Project will be Saskatchewan?s first new potash mine in nearly 40 years. It is one of the world?s most economically attractive potash projects. The project will contribute to Saskatchewan?s growth through employment, tax revenues, utilities, and local partnerships. Located in the southern part of Saskatchewan?s potash belt, the deposit is too deep to be mined conventionally due to rock mechanics and high temperatures. Legacy will therefore be a solution mine. Proximity to the urban centers of Regina and Moose Jaw is imperative, with their workforces and economy, as well as access to highways, railway carriers and, most importantly in the prairies, water. With this unique project setting and mining technique, we are convinced that Legacy will be one of the most efficient, economic, sustainable and safe potash facilities in the world.

Aug 1, 2013

By A. Cummings

This paper reports two aspects of reactivity of complex Ni-Cu sulphide ores: variations that result from stockpiling of a nickel-copper sulphide ore in the Sudbury area and its consequences on flotation behaviour, especially in terms of metal losses to scavenger tails. In relation to the first aspect, self-heating characteristics of the stockpile were carried out by monitoring the internal temperatures of the stockpile. Six heat sensors were installed with respect to external conditions in local weather during a 7-month period. Stockpile temperatures were mainly influenced by ambient temperature with some retardation effects. The maximum temperature recorded in the stockpile was 44 °C. Samples taken at the beginning and at the end of stockpiling were tested to assess variations in behaviour of the rougher-scavenger flotation. Relative to the fresh ore, nickel and copper losses in flotation of the stockpile fines were 5.0 and 3.6 %, respectively. The fresh ore yields concentrates with higher nickel grades due to differential flotation behaviour of pentlandite and pyrrhotite relative to the stockpile fines, which exhibit a truly bulk flotation behaviour at least during the first 3 stages.

Aug 1, 2013

By Martin P. O'Connell

"IT IS INDEED A PRIVILEGE to address a group representing a sector of the Canadian economy so important as is the mining sector. Important, not only today, but certainly of great importance for the future development of Canada, for employment, for our trade balance and indeed, when one looks at what we are calling increasingly an industrial strategy, for the future. Surely mining will have a very significant role to play in fulfilling that. It's of special interest to me, as the Minister of Labour - and I ought to confess at the very beginning that I am just two months into this function - of special interest for me to know that you are giving such attention to labour-management relations. I think it is timely that, from my point of view at least, you do this, because for the first time in twenty four years major revisions of the Canada Labour Code as it relates to industrial relations and disputes settlements are currently in the House of Commons going through their second reading, after an easier introduction and some changes which I would be very pleased to describe later this morning. It is very timely too, I think, that we should be looking at this area because public interest is certainly at a high level. It is not only at a high level but it expresses a good deal of irritation with the current status and procedures and results in collective bargaining and there is some urgent search for more sophisticated or modified procedures for settling differences in labour-management relations. The public wants different kinds of results. I think that is apparent to all of us. They want results in terms of justice and equity on both sides. And it means that a Minister of Labour and certainly governments who often are representing, or are the third party in discussions, have a very important and complex role to play in attempting to create a balance as these two parties come to contracts and come to agreements."

Jan 1, 1972

By F. N. Smith

The carbon steel casings of Heat Recovery Steam Generators (HRSGs) in a co¬generation plant were found to have developed cracks that originated on the inside surfaces. The HRSGs receive hot exhaust gases from the primary Gas Turbines (GTs), which are fuelled with pipeline natural gas. The GTs was initially operating without any suppression of nitrogen oxides (NOx). After being in service for about two years, some of the cracks were found to have penetrated right through the 1/4 in. thick casings. The casings are fitted with insulation on the inside (hot gas side). Examination of steel samples cut from the casing walls revealed (i) fine cracks propagating through the steel from the inside surfaces, and (ii) the presence of relatively large amounts of nitrate ion on the inside surfaces. It was concluded that the nitrate ions originated from nitric acid that was condensing on the relatively cool walls of the casings behind the insulation. Nitric acid was formed in the GT exhaust gases by the combination of water vapour (formed from combustion of the hydrocarbon fuel and from moisture in the combustion air) and nitrogen oxides (formed from nitrogen and oxygen in the combustion air).

Jan 1, 2005

By Shengwu Song, Xuemin Feng

Jinping I hydropower station is located in Sichuan Province in Southwest China. It is built on the Yalong River as a controlling cascade hydropower station in the middle and lower reaches, with power generation as its major function. Jinping I arch dam concerns many engineering issues and has attracted worldwide attentions due to its huge scale and unique settings. It is one of the most challenging projects in China with its 305 meters high arch dam and complex geological conditions for construction, including large-scale tectonic faults, intensively unloaded rock masses and geological asymmetry in its foundation. At present, the concrete arch dam construction has been completed and preliminarily impounded, most of the foundation treatments have been implemented, and four of six generator units had been put into operation in July 2014. In this paper, the analytical methods, design concepts, treatment measures and technical features of strengthening the geological defects in the dam foundation will be presented. Upon geological investigation into the dam foundation, a few large-scale weak discontinuities are observed. The rock masses in the left dam foundation are intensively unloaded, approximately to the horizontal depth of 150–300 m. These serious geological defects lead to a geological asymmetry on the left and right banks, and thus some major difficulties of dam construction are encountered. The influences of geological defects on the dam construction and safety are analyzed comprehensively, followed by the concepts and methods of treatment design. Based on this, the treatment methods of the weak rock masses and discontinuities are carefully determined by numerical analysis and scheme optimization, including the concrete cushion, concrete replacement grids, drainage system, anti-seepage curtains and consolidation grouting, which work together to enhance the strength and integrity of the dam foundation. Evaluations and calibrations through geo-mechanical model tests in combination with field monitoring results in early impoundment period show that the arch dam and its foundation are generally stable and function normally, which suggests that the research methods and treatment design schemes are reasonable and effective. The proposed treatment methods and concepts in the context are helpful for similar complex rock projects.

Jan 1, 2015

By J. A. Drozdiak, W. Tse, P. P. Rosario

"In a recent publication (SAG 2015), we presented a non-conventional high pressure grinding roll (HPGR)-ball mill circuit as a lower capital cost alternative to the “standard” HPGR circuit. The circuit was designed for the treatment of a hard ore and relatively high tonnage (50,000 t/d). That paper provided details such as flowsheets, layouts, and equipment lists for the two options and compared their calculated capital costs demonstrating significant savings for the proposed circuit. This paper extends the analysis to a third option, a traditional semi-autogenous ball crushing circuit, giving the same level of details and now including the operating cost estimates for all three options for a more comprehensive analysis. Moreover, this work also provides information about the strengths and weaknesses of the non-conventional HPGR circuit when compared to the “standard” HPGR option.This study demonstrates that the proposed non-conventional HPGR-based circuit not only provides a lower overall capital costs for the project if compared to a “standard” HPGR circuit but also brings the capital cost to the level of the traditional semi-autogenous grinding (SAG)-ball mill circuits. In addition, the innovative HPGR circuit provides similar operational cost savings of the “standard” HPGR and thus a significant advantage when compared to the SAG option. With the current capital cost sensitivity for most greenfield projects, the proposed alternative circuit should help make HPGR-based circuits more competitive and thus promote the utilization of a technology that enables higher energy efficiency and reduced greenhouse gas emissions. INTRODUCTIONThe application of high pressure grinding roll (HPGR) technology in comminution circuits is well established for the processing of cement, diamonds and iron ore (Broeckmann & Gardula, 2005), and over the past 10–15 years, this technology has slowly been applied to hard ores in high-tonnage precious and base metal operations. Unfortunately, under the current economic climate, the ability to finance large capital projects has become very difficult and companies tend to have an easier time securing funding if the capital expenditures (CAPEX) are low with a proven process method. The traditional semi-autogenous grinding (SAG) mill / ball mill circuits easily fit into this mould, having been installed in countless plants around the world over the past 30 years with relatively low capital requirements. In contrast, it has been well-documented that HPGR-based circuits are capital intensive with complex material handling systems (Seidel, Logan, LeVier, & Veillette, 2006). Although these circuits benefit from reduced operating costs with the increase in energy efficiency and the elimination of steel grinding media (Rosario, Boyd, & Grundy, 2009), if the company is unable to secure financing to build the plant, these advantages remain out of reach. With the current trend to retrofit existing SAG circuits with a secondary crushing circuit to achieve design throughput, the opportunity to circumvent this gross inefficiency by making HPGR-based circuits more capital friendly would greatly benefit the industry."

Jan 1, 2016

The effect of superficial gas rate distribution (Jg profile) on down-the-bank metallurgical response was tested in the rougher-scavenger bank (eight 10-m3 tank cells, 4 roughers and 4 scavengers) at Highland Valley Copper Mine's Cu/Mo separation circuit. Three Jg profiles were tested: (a) as found (i.e., typical practice), (b) increasing decreasing (i.e., increasing from cell 1 to 4 and decreasing from cell 5 to 8), and (c) decreasing-increasing (i.e., decreasing from cell 1 to 4 and increasing from cell 5 to 8). The Jg profile approach proved to be of considerable value. Profile (b) gave the best metallurgical results, i.e., the highest down-the-bank grade/recovery (increase in grade at constant recovery was approx. 3-4% compared to the as found case) and the most efficient Cu/Mo separation (cumulative Cu recovery was reduced by almost half - approx. from 20% to 12%, at 99% Mo recovery). The success of the evaluation prompted the implementation of profile (b). Detailed gas dispersion characterization tests (Jg and Db (bubble size)) showed significant discrepancies between the Jg measured directly (using the McGill University sensor) and the Jg calculated from field instrument readings (volumetric gas flowmeter) and machine dimensions (cell cross-sectional area). Tests were designed to reveal the source of disagreement. It was observed that a significant number of bubbles were not able to float (i.e., they were entrained with the tailings), the evidence appearing to be a significant number of very small bubbles (approx. 200-300 µm) which did not have sufficient buoyancy to rise. Consequently, rather than relying on the field instrument, the evaluation depended on the McGill University Jg sensor, which collects bubbles in a tube near the pulp-froth interface, thus providing significance to the data as the measurements were obtained from bubbles that almost certainly floated.

Jan 1, 2007

"Beneficiation of low grade ores is the process of increasing the grade of a mineral through unit operations that remove and separate the waste (or gangue) material from the valuable mineral that can then be used for further processing or direct use. Important factors when deciding upon a beneficiation program are the feed grade, mass yield and the metal recovery. As lower grade ores are being processed beneficiation is a critical process. How predictive is laboratory test work for “as built” operating projects? Beneficiation includes all or some of the available unit operations to produce a beneficiation flow sheet i.e. associated unit operations including but not limited to optical sorting, radiometric sorting, crushing and screening, coarse cobbing, jigging, dense media separation (DMS), spirals, magnetic separation, flotation, thickening, filtering and drying. Reference to specific projects and the approach developed in formulating a beneficiation flow sheet and a comparison of difficult and simple beneficiation flow sheets are cited. INTRODUCTIONReserves of high-grade iron ores are reducing all over the world, at an alarming rate, over the years as a result of the rapid increase in demand for steel particularly from Japan and then China. The recovery of mineral value from the low-grade ores using present technology is more expensive than DSO ores due to high energy and capital costs. Beneficiation is defined as a variety of processes whereby extracted ore from mining is reduced to particles that can be separated into mineral and waste.Various physical properties of an ore can be exploited to separate a low grade fraction including variation in hardness, density, reflectance, conductivity and magnetism.""Beneficiation"" of iron ores includes concentration, generally by physical removal of unwanted gangue. Also considered beneficiation is the regulation of product size, or other steps such as agglomeration to improve its chemical or physical characteristics prior to smelting."

Jan 1, 2012

By R. A. Nemchek

Over the years, concentrator plant design has evolved from a large number of small grinding mills to a small number of large mills. In many cases, all of the tonnage runs through a single mill (typically a large SAG mill), so that the plant?s performance hinges on the productivity of this one machine. Industry specifications attempt to address the critical nature of today?s grinding mills in a manner that is often overly complex, neglects economics, and is not clearly focused on the end user?s goals. This paper surveys current industry practices, and proposes an improved approach to standards writing recognizing that product design, procurement, manufacturing, and quality are all inter-related in contributing to a project?s success. The lessons learned here can be extended to specifications for all types of machinery.

Jan 1, 2012

By K. Mirkhani, P. Gebski, W. Ying

The campaign life of an industrial metallurgical vessels strongly relies on the quality and quantity of the refractory lining. An operating furnace or converter refractory lining can be assessed either by thermal modeling or by acousto ultrasonic-echo (AU-E) technique or a combination. AU-E is a Non-Destructive Testing (NDT) stress wave propagation technique that has been utilized on a wide variety of smelting vessels for over 12 years with good success. AU-E can determine the thickness of remaining refractory lining, estimate the thickness of build-up or accretion, detect and locate metal penetration and impregnation into the lining, and identify hydrated or cracked areas of refractory. This paper details the AU-E principles, equipment and recent improvements to the data analysis to further improve speed and accuracy. In addition, the paper discusses the AU-E accuracy and limitations through a diverse and vast array of practical examples including a comparison with thermal modeling and physical measurements.

Jan 1, 2011

By G. V. Sirianni, G. E. Viens, R. A. Campbell, G. N. Banks

A combination shaft-electric furnace for the smelting of ores and the melting of metallized feed is being developed at the Mines Branch. When iron oxide pellets are smelted in this unit, they are preheated and partially reduced in the shaft before being transferred to the electric furnace where smelting is completed. Also, limestone flux added with the pellets is-preheated and calcined in the shaft. It has been demonstrated that, in smelting iron oxide in this unit, the throughput of the 250-kva electric furnace can be approximately doubled and the amount of electrical energy required can be very significantly reduced when the shaft furnace is operated in conjunction with the electric furnace. These benefits are achieved mainly by utilizing the sensible heat and latent energy contained in the arc furnace off-gases.

Jan 1, 1971

By J. C. Ingram

IT SEEMS particularly appropriate that, in celebrating its Diamond Anniversary, the Canadian Institute of Mining and Metalturgy chose our Province of British Columbia as its locale in this, our own Centennial year. I am sure your organization is justifiably proud of its achievements and growth over the period of its sixty years, and we, for our part, are justifiably proud of our growth over our first one hundred years. With your kind indulgence I pro-pose to talk to you today about our industrial growth, or, to put it an-other way, to highlight, historically, our progress in industrial development over the past one hundred years, and to take the liberty of speculating on what we may reasonably look forward to over the next few years. I am sure, Mr. Chairman, that some may have questioned the appropriateness of a talk on the industrial development of British Columbia to the Canadian Institute of Mining and Metallurgy. However, strangely enough, we in British Columbia owe our origin, constitution-ally and industrially, to the mining industry.

Jan 1, 1958

By C Jincheng, L. Liang, L. Wenjun

"Considering overgrinding in a grinding process, the grinding characteristics of comminuted hematite products using a HPGR and a conventional CC were comparatively studied. The major properties including particle size, grinding kinetics and grinding technical efficiency (Et) were investigated. Individual size distributions (ISDs) of -2.0mm in a HPGR product showed a more significant “double-peak” characteristic than a CC product. As a result, HPGR products were finer and had a wider full-size distribution because of the greater proportion of fines. The parameters m and zi in m-th order grinding kinetics were analyzed by the partial-derivative method and the critical time tc(tc = exp (1/ zi)) was obtained. zi mainly affected the breakage rate when t < tc; otherwise, m mainly affected the breakage rate. In these tests, tc was considerably higher than the grinding times, and HPGR products yielded a higher zi-value than the CC product for the same sieve size. This indicated that HPGR products had a higher breakage rate and needed a shorter grinding time for a certain grinding fineness. Et was calculated by simulating the size distributions of batch grinding products. HPGR products gave a lower Et at a decreasing rate than the CC products for -2.0 mm feed and -0.5mm feed, and then showed a slightly higher Et for -2.0+0.5 mm feed. This indicated that overginding in HPGR full-size products was more serious under the condition of coarse grinding, whereas the efficiency was higher and overgrinding weakened significantly in HPGR coarse products because of screening-out fines. Based on the above research, a new process of “ultra-crushing in HPGR – classified grinding” was advanced, reducing ores tonnage into first stage ball mill significantly, improving grinding efficient and weakening overgrinding in the whole grinding process.INTRODUCTIONIn mineral processing, comminution accounts for a substantial portion (approximately 60~70%) of the energy consumed in plants. As an ultra-fine crushing equipment,the application of the HPGR for industrial comminution has been paid close attention because of its low specific energy, low steel consumption, high capacity and high ratio of reduction, among others (Schonert, 1998; Norgate & Weller, 1994; Fuerstenau & Kapur, 1995). HPGRs comprise two counter-rotating rolls that draw feed material into the roll gap. One roll is fixed to the mainframe, while the other movable roll is mounted on slides and positioned by hydraulic rams. The specific pressing force (SPF) (i.e., total force divided by projected roller area) is typically in the range of 3~9 N/mm2 depending on the application, while pressures of up to 1000 N/mm2 have been measured within the operating gap (Maxton , Morley, & Bearman , 2003)."

Jan 1, 2016

By J. R. Kish, J. Dabrowski

"The susceptibility to intergranular corrosion modes is a major technical issue preventing widespread utilization of higher strength welded AA7xxx extruded beam profiles, in the peak-aged T6 condition, in automotive bumper assemblies. A study was undertaken to evaluate the relative exfoliation corrosion resistance (ASTM G85-A2) as a function of joint design parameters, namely the base alloy composition, heat-treated condition and beam orientation after exposure to a cyclic acidified salt spray test. This paper documents the major findings extracted from this study.INTRODUCTIONBumper systems play a predominant role in the passive safety of an automobile, since they are one of the main structures for absorbing the collision energy in the event of an automobile crash. Heattreatable AA6xxx-series (Al-Mg-Si) and AA7xxx-series (Al-Zn-Mg) Al alloys, with relatively high strength, toughness, energy absorption, weldability and formability, make it possible to design costcompetitive bumper systems to crush in a controlled fashion. In this context, Cu-lean AA7xxx extrusions, such as AA7003 and AA7108, which exhibit higher strength than AA6xxx extrusion, such as AA6082, represent an attractive light weight material from which to fabricate bumper assemblies (Clausen et al., 2000; Pedersen et al., 2008; Chen et al., 2009).Arc welding is a key joining process for AA7xxx alloys within the transportation industry. A major technological issue preventing widespread utilization of arc-welded AA7xxx joints is the susceptibility to severe localized corrosion (Kent, 1970, Reboul et al., 1985; Holroyd et al., 1987). It generally occurs as exfoliation corrosion within a heat affected zone (HAZ) a few millimeters from the weld bead, or a type of stress corrosion cracking (weld-toe cracking), which initiates at the weld toe and propagates into the interfacial region between the weld bead and the HAZ (so called “white zone”). In addition to the micro-galvanic cell activity induced by the intermetallic compound constituent and strengthening particles present, there is strong evidence that macro-galvanic cell activity between the weld bead and base AA7xxx alloy may be playing a controlling role. Electrochemical profiles taken across fusion welded joints, in cross-section, during exposure to saline solutions suggest that a significant potential difference exists across the AA7xxx arc-welded joint (Shumaker et al., 1967; Grauer and Wiedmer, 1980; Tuck, 1985, Onoro and Ranninger, 1993). These studies consistently show that the HAZ and base alloy are more electronegative with respect to the weld bead (arc-welded with AA5xxx filler wire). Despite this initial important work, the majority of the recent corrosion research effort on welded AA7xxx alloys has focused on the performance of friction stir welds (Lumsden et al., 1999; Wadeson et al., 2006; Hatamleh et al., 2009)."

Jan 1, 2012

By R. E. Ray

"As real estate for new development in urban settings becomes scarce, commercial high rises are being constructed above open passenger rail tracks and vehicular roadways. Rail and roadway overbuilds are treated as tunnels requiring emergency ventilation systems for train or automobile and truck fires. The value of floor space in residential and office towers poses challenges to engineers responsible for designing fan rooms and shafts for tunnel ventilation systems within the towers. This paper describes a case study of the unique incorporation of tunnel ventilation fan plants in the overbuild structure of a passenger railyard and an adjacent roadway.INTRODUCTIONTunnel ventilation systems are required for passenger rail and transit (subway) tunnels by the NFPA 130 Standard for Fixed Guideway Transit and Passenger Rail Systems, and the NFPA 502 Standard for Road Tunnels, Bridges, and Other Limited Access Highways requires tunnel ventilation systems for vehicular (road) tunnels. Passenger rail and transit (subway) tunnels are typically ventilated with a series of shafts placed longitudinally along the tunnels to provide piston relief for normal train operations and emergency ventilation of train fires utilizing reversible axial flow fans. The shafts are incorporated in dedicated ventilation buildings that house the tunnel ventilation fans and starters, switchgear to power the fans and other equipment and systems in the building, Programmable Logic Controllers (PLCs) to control fan operation with Supervisory Control and Data Acquisition (SCADA) software, and HVAC fans and ductwork to ventilate the spaces in the building. These ventilation buildings may also provide access to the tunnels below with ingress/egress stairs for use by first responders and firefighters entering the tunnels and train or transit system passengers exiting the tunnels in an emergency. A photograph of a passenger rail ventilation building that encompasses four tunnels is shown in Figure 1."

Jan 1, 2019

By B. Westin, G. Voicu, C. Daoust

Orogenic gold deposits represent a major class of deposits that are found in various rock types of various ages. Those deposits show a strong structural control that usually complicates their interpretation at the regional and deposit scales. The Rosebel Gold district located in Surinam (South America) is hosted in a Paleoproterozoic greenstone belt of the Guiana Shield, and has been recently classified as one of those orogenic gold deposits. The gold district comprises eight distinct deposits located along three different structural trends and within different rock types. The mineralization is undefonned and shows a strong structural control characteristic of orogenic gold deposits. All the deposits of the Rosebel Gold district have been subject to a detailed structural analysis that has led to the elaboration of a new structural model for the whole gold district, which is now differing considerably from the previous models. This characterization had direct implications at three different scales. 1- While the older models were considering some areas of the property as gold-barren, the new structural model has led to recent exploration campaigns which have revealed positive results. 2- At the deposit scale, the comprehension of the various vein systems and of the folding of the host rocks has helped the establishment of optimized drilling campaigns. 3- At the mining scale, the comprehension of the architecture of the veins helps for the elaboration of optimized mining method. This study thus shows that the structural analysis of orogenic gold deposits is critical, and should be a priority for exploration and production in any mine.

Jan 1, 2011

By P. Mottahed, E. De Souza

One of the major unsolved problems of safe, economical roof support in the evaporite industry has been that of obtaining and maintaining anchorages in relatively soft rock. This is due to the viscoelastic and viscoplastic behaviour of salt rock and associated deposits. This paper introduces a low-cost, yieldable support mechanism, consisting of a system of buckling disks, which provides viable solutions to dynamic support. The yieldable support system offers a number of advantages in comparison with existing dynamic support systems. It is characterized by its simplicity in design and installation, repeatability in behaviour and cost effectiveness. It also has the added advantage of providing the operator with a means of assessing support behaviour and ground performance by direct visual observation of changes in disk shape. Thus, the system can be utilized as a warning mechanism of ground stress and support load conditions. Such system not only provides a feasible and more effective rock mass stabilization strategy but improves mine safety.

Jan 1, 1999