Search Documents

By D. S. Campbell

THE chief factors influencing the decision to build the Big Missouri mill underground were the topography of the country and the climate. The location underground assured certain saving in the cost of operation, such as the hearing of the mill, shovelling snow, and handling ore, which, over a period of time, would offset the greater initial cost of the mill excavation and machinery installation underground, as compared with the cost of a like plant on the surface. At Gilman, Colorado, where conditions are somewhat similar, the Empire Zinc Company, at their Eagle mine, are treating their lead-zinc ore in a mill built entirely underground. Company officials made a study of this plant before proceeding with the mill at Big Missouri. LOCATION, CLIMATE, TOPOGRAPHY The Big Missouri mine is situated on the Upper Salmon river, 22 miles north of Stewart, B.C., which is at the head of Portland canal, a narrow natural channel which penetrates 100 miles inland from the coast into the Coast Range mountains. Stewart, the distributing centre for the district, is about 600 miles north of Vancouver. The Big Missouri claims lie on and down the sides of the Big Missouri ridge, which extends north and south between the Salmon River and Cascade Creek valleys. The ridge rises to an elevation of 3,600 feet, is about half a mile wide, and to the east slopes down to the Joker flats in Cascade Creek valley. The Big Missouri camp is located on the flats at elevation 2,800 (see Figure 1). Preliminary development of the property took place from this point with an adit driven under the ridge. The western side of the ridge slopes steeply down to the Salmon glacier at elevation 1,900. Ore found on the 2,850 level extended down, and, in order further to explore the ore-body, the 2,850 level was driven through to the west side of the ridge, a surface incline tramway was built, and a lower tunnel driven at elevation 2,350, five hundred feet below the original 2,850 level, from the west side of the ridge. This tunnel development avoided the necessity of sinking, which would have been costly, as the mine makes a great deal of water (see Figures 1 and 2).

Jan 1, 1938

By G. W. H. Norman

"The La Corne molybdenite-bearing veins, discovered in 1915, lie halfway between Amos and Val d'Or near the southwest corner of La Corne township, Abitibi county, Quebec. The Molybdenite Reduction Company, which carried on operations during 1927 to 1930, sank a 200-foot inclined shaft to develop the property and produced about 22 tons of concentrntes from a 30-ton mill during 1929. Hollinger Consolidated Gold Mines, Limited, carried on further underground exploration in 1930. The Molybdenite Corporation of Canada drilled a part of the property in 1938 to 1939 and produced 1 ton of concentrates in 1938. Wartime Metals operated the property from 1942 to July 15, 1945. At this time the mill was enlarged to treat 200 tons daily. Molybdenite Corporation of Canada since July 15th, 1945, have continued the operation of this property and have revised the mill flow-sheet in order to produce both a bismuth and a molybdenite concentrate.The production for the period 1942-1946 is as follows:Total molybdenite production from the mine in the 1942 to 1946 period was about 4,127,400 lb.The La Corne deposit occurs at the northwest contact of a small mass of biotite granite with biotite schist. The form and extent of the biotite granite mass is concealed by a wide sand plain that extends northwest and west from the deposit and overlies bed-rock except in four small outcrop areas. These are spaced 1,000 and 2,000 feet apart along a narrow strip extending 5,000 feet south from the mine. The outcrops suggest that the granite must be at least 1,500 feet wide and 3,000 feet long northeastward. Where exposed in the mine workings the contact dips 70°N.W., but is not a sharply defineable feature due to the presence of numerous granite dykes and tongues in a zone of biotite schist 100 feet wide along the margin of the granite. The biotite schist in the few outcrops that flank the north and south sides of the granite strikes northeast and dips 60° to 70° S.E."

Jan 1, 1954

By M. M. C Jiménez, J. A. S Ténorio

For the recovery of valuable materials and for the protection of environment, recycling process of printed circuit board is an important subject of study. Moreover, the popularization of the computers and its technological evolution has generated a large number of waste electrical and electronic equipment. This paper presents a study of synergistic solvent extraction of copper, nickel and zinc from a sulfuric leaching liquor of printed circuit boards (PCB’s). The percent extraction of copper, nickel and zinc from dilute aqueous sulfate media besides synergistic effect of mixture of the .extractants Cyanex 272 and D2EHPA have been studied. Furthermore, different conditions such as temperature, pH of the feed solution have been examined. The results suggest that the synergistic effect of the .extractants mixture enhance the extraction efficiency of nickel.

Jan 1, 2014

By M. Maeda, H. Sasaki

"Precious metals such as platinum, palladium, and rhodium are commonly used for automotive catalyst converters. To recover these metals with lower environmental load and cost, exposure to zinc vapor was proposed as a pretreatment prior to acid leaching. Alloying with zinc is expected to enhance dissolution of precious metals and reduce the amount of toxic chemical agents required for the leaching. This study examined the effect of the alloying pretreatment using model catalysts. Catalysts were immersed in leaching solutions for a predefined time with or without zinc vapor pretreatment, and the amount of dissolved metals was then evaluated. INTRODUCTIONAutomotive catalysts account for large portions of the world consumption of platinum (Pt), palladium (Pd), and rhodium (Rh) (Butler, J., 2011). Because of their limited production and high prices, recovery of the precious metals from spent catalysts is obviously an important issue. A representative structure of an automotive catalytic converter can be described as a monolithic ceramic support with a honeycomb structure which is coated with porous oxides such as those of aluminum (Al2O3), cerium (CeO2), and zirconium (ZrO2) (Heck & Farrauto, 2001; Matsumoto & Shinjoh, 2007). Small particles of precious metals, originally several nanometers or less, adhere to the oxides.Typical recovery processes for precious metals from scraps are shown in Figure 1 (a)-(c) (Habashi, 1997; Yoo, 1998; Shibata & Okuda, 2002). Precious metals can be recovered by using non-ferrous smelters as Figure 1 (a) shows. Smelted along with metals such as copper (Cu), precious metals and ceramics in the scraps are absorbed into the metal phase and slag phase, respectively. Because the metals separate from Cu as anode slime in successive electro-refining, such a process can recover precious metals as co-products of Cu. However, in order to prevent negative effects on the principal process, a specialized procedure is needed. Figure 1 (b) is a specialized approach in which scraps are melted at elevated temperature with Cu called the Rose process. Here Cu works as a collector metal, and the absorbed precious metals are then concentrated by oxidation of Cu. Such a process can separate precious metals from ceramics constituting catalyst converters. Smelting at high temperature, however, requires extensive equipment as well as a high amount of energy. On the other hand, hydrometallurgical processes may be effective to separate precious metals from ceramics into an aqueous solution, because chemical agents can act on these metals selectively (Figure 1 (c)). Leaching of precious metals, however, requires strong acid and oxidizing agents because of their corrosion resistance; this makes liquid waste disposal and the large environmental load controversial. To solve the problem, a metal vapor pretreatment was proposed (Okabe, Yamamoto, Kayanuma, & Maeda, 2003a, 2003b; Kayanuma, Okabe, Mitsuda, & Maeda., 2004; Kayanuma, Okabe, & Maeda, 2004; Itoh, Kayanuma, Miyake, Kimura, & Maeda, 2005). A flow diagram of the process using zinc (Zn) vapor is shown by Fig. 1(d). Exposed to Zn vapor, precious metals are expected to form alloys which dissolve more easily than pure precious metals, thus reducing the use of chemical agents and environmental load involved with successive leaching. In previous research (Sasaki, Miyaki, & Maeda, 2010; Sasaki & Maeda, 2010, 2012), dissolutions of precious metal alloys formed by Zn vapor treatment were examined in hydrochloric acid (HCl) using an electrochemical method, and it was confirmed that these metals dissolved at higher rates from the alloys than from their pure states (Figure 2). In this study, the availability of the alloying pretreatment was demonstrated by testing on model catalysts in leaching solutions."

Jan 1, 2012

By G. A. Sutton

"At the San Manuel mine (Arizona, USA), in-situ copper leaching of a copper porphyry deposit was carried out from 1986 to 1999 during underground and open-pit mining. In 1993–1994, well¬field testing of the supergene zone, composed primarily of chrysocolla and copper-rich clay minerals, led to estimates that 52% of the acid-soluble copper (ASCu) could be recovered during in-situ leaching; however, the actual recovery from zone 6, which had the longest leach history, was approximately 42%. Comparing drillcore assay data from holes drilled before and after leaching also indicated an approximate recovery of 42%. The discrepancy between the predicted (52%) and actual (42%) recovery is probably related to several factors, including difficulty maintaining fluid saturation, channelling effects, and gypsum precipitation. ¦ KEYWORDS Copper oxides, in-situ leaching, Modelling, Porphyry, Solvent extraction and electrowinning (SXEW), Well-to-well RÉSUMÉ À la mine San Manuel (Arizona, États-Unis), on a procédé de 1986 à 1999 à la lixiviation in-situ de cuivre d’un gisement porphyre cuprifère pendant l’exploitation minière souterraine et à ciel ouvert. En 1993 et 1994, des essais effectués dans des champs de captage de la zone supergène, composée principalement de chrysocolle et de minéraux argileux cuprifères, ont abouti à des estimations selon lesquelles on peut récupérer 52 % de cuivre soluble dans l’acide (ASCu) pendant la lixiviation in-situ ; toutefois, la récupération réelle dans la zone 6, qui affiche l’histoire la plus ancienne en matière de lixiviation, était d’environ 42 %. La comparaison des données d’analyses de forage obtenues à partir de trous forés avant et après la lixiviation indiquait également une récupération approximative de 42 %. La différence entre la récupération prévue (52 %) et réelle (42 %) réside probablement dans plusieurs facteurs, notamment la difficulté à maintenir la saturation des fluides, les effets de canalisation et la précipitation du gypse. ¦ MOTS CLÉS d’un puits à l’autre, extraction par solvant et extraction électrolytique (SXEW), lixiviation in-situ, modélisation, oxydes de cuivre, porphyreINTRODUCTION in-situ copper leaching at the San Manuel mine, Arizona, USA (Figure 1), began in 1986. It was recognized that some of the copper oxide resource was not economically recoverable by conventional open-pit and heap leach methods using solvent extraction and electrowinning (SXEW) and a high stripping ratio would be required to access part of the resource. At the time, in-situ leaching was becoming popular in the uranium industry, but the approach was virtually unknown in the copper industry, especially at a large scale."

Jan 1, 2019

By H. Thomasson

This paper will deal with on-site maintenance welding using the stick electrode, electric arc process. It is primarily concerned with the underlying principles, the application of which, or the lack of such application, governs the success or failure of the operation. It will discuss first the base metal or item to be welded, including the field identification of its weld-ability and the determination of the procedures to be followed. Second, it will outline heat effects and the interrelation between heat applied as part of a welding operation and heat deliberately applied as part of a heat treating cycle, stressing the fact that in welding the same basic principles are effective. The third consideration will be weld metal and its control of both composition and properties. Last, but not least, distortion, shrinkage and residual stress will be considered and practical means for minimizing their adverse effects outlined.

Jan 1, 1967

By B. K. Choi, G. E. Kim, S. Noh, T. K. Kim

Oxide dispersion strengthened (ODS) steel has been developed as the most prospective core structural material for next-generation nuclear systems because of its excellent high strength and irradiation resistance. In ODS steel, finely dispersed nano-oxide particles with a high number density in the homogeneous grains can be very attractive to achieve superior mechanical properties at high temperatures, and these favorable microstructures can be significantly changed using process parameters during the mechanical alloying procedures. In this study, the effects of mechanical alloying times on the microstructure of 10Cr-1Mo ODS martensitic steel were investigated. Pre-alloyed powders with Y2O3 powder were mechanically alloyed for various milling times using a high energy horizontal ball-mill apparatus (model: symoloyer CM20). Powder properties such as the mean particle size, size distribution, and crystallite size were evaluated. Uniaxial hot pressing was employed to consolidate the milled powders. The results of a microstructural observation after the MA and UHP processes indicated that the homogeneity of the martensitic structures was considerably increased with the longer milling time. It is thus concluded that the mechanical properties of the ODS martensitic steel are greatly dependent on the mechanical alloying times.

Jan 1, 2015

By P. A. Tichauer

Arbitration is a flexible method for dispute resolution that gives control to the disputing parties while still maintaining a clear and well-structured decision making process. It responds to the desires of the parties for a resolution that is fair, binding and enforceable and is guided more by pragmatism, efficiency, effectiveness and equality than by a need to comply with the legal procedures and practices of any single country or jurisdiction. Arbitration is particularly well suited for the resolution of disputes pertaining to international commercial agreements which are often present in the metallurgical sector. This paper provides a simplified outline of the features and advantages of arbitration as well as commentary regarding certain prerequisites in order for arbitration to be binding and enforceable.

Jan 1, 2015

By A. A. McCloskey

APPROXIMA TEL Y 95 percent of Waite-Amulet's Lower A orebody will be mined by diamond-drill stoping. This method of stoping was developed, and has been successfully applied, at the Noranda mine in recent years(1) and is now used in several base-metal and gold mines in north-western Quebec and in other parts of Canada, South Africa, and Australia. The purpose of this paper is to deal with the features of the Lower A ore-body which led' to the adoption of this method of stoping, and in addition to give a general description of stope layout, stope development, main haulage development, chutes and grizzlies, diamond drilling for stope blasting, diamond drilling and equipment, primary blasting, secondary blasting, haulage and loading, ore pockets, pumping and drainage,. and shafts at Waite Amulet. Figure 1 is an isometric projection of the orebody, illustrating the mining system. The factors that led to the adoption of diamond-drill stoping of Lower A orebody are as follows: (1) Safety.0 (2) Size and shape of the orebody, and depth of the orebody below surface. (3) Strength of the hanging-wall, footwall, and sulphide ore. (4) Continuous ring-drilling from sub-level drifts, with no delay for blasting. (5) Large-tonnage blasts at the end of Saturday afternoon shift, after ali men are out of the mine. (6) Sub-levels may be retreated from top to bottom simultaneously, or lower sub-levels may be retreated first without any change in the ring-drilling la yout. (7) Large stopes up to 100 feet wide can be mined, leaving substantial pillars up to 60 feet in width, which may be partially recovered by âiamond~drill stoping or by other stoping methods. (8) A large tonnage may be drilled-off in advance of blasting, but only a supply of unoxidized ore for flotation treatment is blasted. (9) Better ventilation during working shifts. (10) Gravity flow of all broken ore to grizzlies located in the footwall of the orebody. (11) Electric blasting by a crew of two men.

Jan 1, 1941

By V. G. Papangelakis, G. A. Moldoveanu

"Rare earths adsorbed on clay minerals are easily recovered via ion exchange during leaching with inorganic monovalent salt solutions. The leaching efficiency of various salts at 0.5M and 25°C was investigated as a function of cation type and salt system (sulphates vs. chlorides). (NH4)2SO4 was identified as the lixiviant of choice and a procedure was established to investigate the influence of lixiviant concentration, temperature, pH and agitation on desorption kinetics and REE extraction levels. It was determined that the kinetics were fast and the optimum leaching conditions (for >80% total REE extraction) required pH below 5 and moderate temperatures (<50°C). INTRODUCTIONRare earth elements (REE) are at the core of numerous advanced applications due to their various uses in high strength permanent magnets, lasers, automotive catalytic converters, fiber optics/superconductors, and electronic devices (as phosphors in TVs and display screens for computers and cell phones). Because of the ongoing development of new technologies, there is an increased demand for REE in the international market, with emphasis on identifying new resources to insure an adequate supply for present and future use. World production of rare earths is dominated by China, the United States and Australia; however, in terms of resources, China dominates the world potential with reserves estimated to be over 90% of the total (Chen, 2011).The main commercially significant REE sources, as reviewed by O’Driscoll (1991) are bastnasite (carbonate) and monazite (phosphate) minerals, containing up to 70% wt. rare earth oxides (REO). In spite of being high grade, these ores are associated with elevated recovery costs due to difficulty in mining, separation and beneficiation. Moreover, aggressive conditions are required to solubilize the REE from the mineral, such as leaching with hot, concentrated acids or baking in 70% NaOH (Gupta & Krishnamurti, 2005)."

Jan 1, 2012

By A. Ehsani

"Seas and oceans constitute about 70% of the earth’s surface. They contain an enormous stock of various mineral resources such as sedimentary (marine placers), massive sulfide ore deposits, manganese nodules and cobalt-rich ferromanganese crusts. Sea and ocean floor ore deposits could well contribute to the meeting of ever-rising demand for raw materials in the metal industry. In this regard, more research and development in science and technology appear to be required to ensure maximum benefit from the mineral resources of seas and oceans. Since the 1960s, a variety of mineral and metallurgical processes have been studied and developed to deal with marine ores and to extract metals such as gold, nickel, copper, cobalt, manganese, tin, platinum group metals (PGM), zirconium, thorium, etc.In marine environments, there are many parameters which can affect the selection of the mineral and metallurgical processes. These include the extent and grade of the deposit, mineralogical and chemical properties of the deposit, and physical properties of minerals present with particular reference to particle size distribution and mineral liberation size.In this paper, we briefly review the latest trends in processing and extraction of marine mineral resources. Mineral processing technology is mostly applied for recovery of precious metals i.e. gold and PGM, in particular, from marine placers. In general, pre-treatment (sizing, classification, dewatering), gravity concentration techniques (shaking tables, spirals, jigs, etc.,), flotation, magnetic, and electrostatic separation are the options for enrichment of marine placer ore deposits. In the case of massive sulfides, manganese nodules/cobalt-rich crusts, hydrometallurgical and pyrometallurgical methods (as proven technological methods) can be exploited for extraction of metals from concentrates after physical separation or directly from marine ores. The hydrometallurgical treatments involve acid (e.g., sulfurichydrochloric) and alkaline (e.g., ammonia) leaching with different reducing agents and pre-treatments such as roasting. Alternatively, pyrometallurgical treatments involve mostly smelting, chlorination and segregation processes."

Jan 1, 2016

By F. A. McLean

Given a promising claim and the required financial backing to develop it, the first problem that confronts the mine operator is usually the selection of the necessary compressed air plant. The size and type of drive are questions that naturally follow, the former being determined largely by the amount of money available and the speed with which it is desired to carry on the programme of development. The type of drive, such as electric motor, steam or oil-engine, depends on local conditions and has an important bearing on the cost of operations. ns. Few prospective mine operators are fortunate enough to locate claims within the service radius of electric power-lines, although this is more likely to happen nowadays than formerly. In the majority of cases, however, some other form of prime mover is necessary. When wood or coal are available at moderate cost, a small steam-driven plant is usually chosen. Such plants are often arranged so that they can be converted to electric-drive should future developments at any time make this desirable. Many plants of this type are installed in northern Ontario mines. When wood or coal are costly or difficult to transport, oil-engine driven mining plants have many advantages in their favor, and are now quite commonly used. Oil in some locali-ties is considerably cheaper than wood or coal, and is much easier to transport over bad roads.

Jan 1, 1924

By L. C. DeCory

"Concrete is a common denominator to the building process and portland cement is an integral and necessary component of concrete. The cost of portland cement is nominal and its cost comprises, in most instances, a small portion of the total cost of ""put-in-place"" concrete.The domestic demand for portland cement in Canada is projected to be slightly less than 11 million short tons in 1980. In order to achieve this projected goal, stabilization or lowering of the cost of put-in-place construction is necessary. This enhancement of the cost of building can be achieved by:(1) improving the building process;(2) refining and improving design techniques; and(3) developing improved and economical concrete products.Some of the techniques and materials that will lead to building cost stabilization include systems building in its broadest sense, slipforming, precasting, prestressing, computer design, lightweight aggregates, fibrous concrete and integration of building components."

Jan 1, 1973

By K. Ihara, R. Akiyoshi, Y. Takaki, S. Kang, H. Shishido

"Tensile tests and scanning electron microscopy-electron backscattered diffraction (SEM-EBSD) analysis were performed in an Al-Mg-Si alloy to clarify the effect of annealing and cold-rolling reduction on the texture formation. The hot-rolled specimens were cold-rolled with the reduction of 58-75%(CR1), followed by annealing at 773 K for 5 min(IA). The secondary cold-rolling(CR2)for the IA specimens with the reduction of 33–66%, followed by the solution heat treatment(ST), were performed. Focusing on the CR1 and CR2 specimens, the average r-values increased with higher primary and lower secondary cold-rolling reduction, respectively. This was considered to be due to the increase of r-values measured in the direction of 45 degree with respect to rolling direction, caused by the formation of the ß-fiber components (Brass {011}<211>, Copper {112}<111> and S {123}<634>) with high density. Based on the texture analysis of annealed specimens it was suggested that the high density of the ß-fiber components after IA and the small amount of stored strain energy of CR2 introduced by the lower cold-rolling reduction remained the ?-fiber components even after solution treatment.INTRODUCTION Al-Mg-Si alloys have been applied to automobile body applications, due to their excellent paint-bake hardening (age-hardening) and corrosion resistance compared to other aluminum alloy. On the other hand, the mechanical properties and deep drawability of Al-Mg-Si alloys are inferior to those of steels. Thus, it is important to improve the mechanical properties and deep drawability in order to expand the application components. One of the best methods to improve the deep drawability is to increase the Lankford coefficient (r-value). Previous studies reported that the increase of the average r-value ( ) improves the deep drawability. The relationship between the r-value and texture of the alloy is also well known. Inoue et al. reported that the ß-fiber components, such as Brass ({011}<211>), Copper ({112}<111>) and S ({123}<634>), increase the r-value measured in the direction of 45o with respect to the rolling direction. r"

Jan 1, 2018

By F. Richards

"The property of the Cariboo Gold Quartz Mining Company; Limited; is in the Wells-Barkerville district of Cariboo mining division. It consists of a group of 106 Crown granted mineral claims and fractions; and extends for over 6 miles along what is termed the Barkerville gold belt. The main portal and mine camp are half a mile south of Wells; which lies at the northeast end of Jack of Clubs lake and is reached by a 55-mile motor road from Quesnel; the northern terminus of the Pacific Great Eastern railway.Gold-bearing quartz veins were discovered on the surface in various parts of the property by different prospectors as far back as 1877, but the work that led to the formation of the present company was performed by Al Sanders in the year 1926. Sanders dug trenches and drove small adits on quartz veins containing gold above what is now known as the Sanders zone. Very little underground work has been done beneath the earliest known discovery-the B.C. vein. The Cariboo Gold Quartz Mining Company was formed in the autumn of 1926. The total production of gold from its beginning in 1933 to the end of 1944 has been as follows:"

Jan 1, 1954

By George Langford

Introduction The manufacture of ductile beryllium is one of the most interesting problems confronting the metallurgist today, and one which becomes more acutely in need of resolution as the uses for beryllium increase. Beryllium belongs to the hexagonal group of metals along with zinc, magnesium, and cadmium. The melting point of the metal is about l,280°C. ± 5°C. Due to its brittleness, the metal&apos;s chief use is as an alloying agent in copper and iron. The very low absorption coefficient of beryllium for x-rays makes the metal ideal for x-ray windows, and, similarly, because of its low capture cross-section for neutrons, the metal holds a preferred position in the field of nuclear physics. Modern x-ray diffraction methods were responsible for explaining the mechanism whereby zinc metal, although brittle when cast, could be made ductile at room temperature. The diffraction patterns of zinc and magnesium indicated the importance of the parts played by recrystallization and preferred orientation in this mechanism. It was with this in mind that an Investigation into the recrystallization and preferred orientation of beryllium was undertaken. The investigation, after a series of experiments were conducted involving cold-working and annealing, yielded the recrystallization temperature curve for beryllium. Both the texture of preferred orientation and the effect of recrystallization on this texture when subjected to compressive stresses were also determined. W. A. Alexander, J. K. Swinton and L. M. Pidgeon, in their investigation on The Recrystallization Temperature of Beryllium (C.I.M., Trans., Vol. L, 1947, pp. 657-664), utilized the Brinell ball as a means of cold straining the metal. Sufficient strain was developed to estimate the recrystallization curve for the metal. However, in order to determine the lowest recrystallization curve, as well as to develop a preferred orientation structure, larger deformation than that possible with a Brinell ball was required. The plastic deformation of beryllium can be carried out at an elevated temperature above 700°C. Above 850°C., the metal is quite ductile and can be readily compressed or extruded.

Jan 1, 1948

1. Scientific prospecting has had a profound and some-what unexpected effect on the world&apos;s supply of raw materials over the past twenty years. Where shortages were recently anticipated, abundance now prevails. It seems probable that, for the foreseeable future, adequate metallic resources will be found at costs well within the world&apos;s economic means. 2. The amount of research devoted to scientific prospecting has been extremely small in relation to the possible importance of the problem and to what could be done. It has been dominated by the thought of a dozen brilliant men, and true research expenditures have not amounted to more than a few million dollars. 3. An undue proportion of the expenditures have been for so-called geological research -mostly of a petrologial character. The results have essentially been of historic interest only. However, there has been some in-crease in genetic understanding, and this is of great importance for future resources. 4. Basic advances in mineral exploration have been made in detection techniques, generally called geophysics and geochemistry.

Jan 1, 1964

By R. Burnette

Gold has been mined from a variety of deposit types that range in age from Archaean to Recent. The large variability in the geological settings of the gold deposits implies transport and concentration of gold by magnetic, hydrothermal and sedimentary processes. The factors that control the concentration of gold at certain sites and the grade estimation thereof remain major topics of debate. Due to the complex nature of the Witwatersrand Basin a mineralogical study, including mineralogical, petrographic and geochemical investigation was launched on TauTona Mine in order to characterize the various reef facies. The aim of the investigation was to determine if a correlation could be found between macroscopic characteristics of the reef, hanging wall and footwall, and the microscopic nature of the ore (especially gold grade). Petrograpgic and mineralogical results indicate that a correlation exist between gold, detrital and hydrothermal sulphides, uraninite, carbon, detrital heavyminerals and phyllosilicates. No correlation exist between gold and Mg, Fe or S. It appears that clast supported reef is of higher wade than matrix supported, but more work is suggested. No correlation exists between reef thickness and grade. The reef samples had the lowest phyllosilicate content compared to the hanging wall and footwall samples with pyrophyllite the most dominant. All of the correlations diagrams showed significant scatter and suggests a multi- factorial mineralization model. Gold distribution is also controlled by sedimentary features and thus it is not possible to select a single model for the formation and distribution of gold. It is evident that both sedimentary and hydrothermal factors influenced the mineralization and gold distribution on TauTona mine. It is thus essential that all related theories be incorporated in the development of a grade prediction model.

Jan 1, 2011

"Previous studies on the effect of polytetrafluoroethylene addition during chalcopyrite leaching under conditions similar to those of the CESL process have reportedly resulted in complete leaching of the copper without the need for grinding of the flotation concentrate. However, these studies employed a pulp density of only 1% and finely sized PTFE particle that required the use of high impeller rotation rates that are not sustainable at an industrial scale. This paper explores the performance of 1/8” diameter balls of PTFE, that readily sink in the leach solution, on leaching performance at impeller rotation rates and ore pulp densities more typical of industrial practice. Possible routes for separation of the PTFE from the leach residues and their regeneration for recycling back to the leaching stage are also discussed.INTRODUCTIONChalcopyrite, CuFeS2, is the most important primary sulfide source of copper. While pyrometallurgical smelting of chalcopyrite remains the only widely accepted route for treating chalcopyrite concentrates, several medium temperature pressure oxidation processes are claimed to be economically feasible (Muir & McDonald, 2007). Among these, the CESL process has been extensively piloted and demonstrated at the prototype scale. The overall process chemistry of the CESL process may be summarized as follows (Marsden & Wilmot, 2007):4CuFeS2 + 5O2 + 4H2SO4 ? 4Cu2+ + 4SO4 2- + 2Fe2O3 + 8S0 + 4H2O (1)4CuFeS2 + 17O2 + 2H2SO4 ? 4Cu2+ + 10SO4 2- + 4Fe3+ + 2H2O (2)Though copper extractions of over 95 % are achieved, the CESL process requires extra grinding of the concentrate (Muir & McDonald, 2007). This is because leaching is conducted at temperatures around 150 °C, where the elemental sulfur produced is molten and grows thicker on the mineral’s surfaces as oxidation progresses, creating an increasingly large barrier for mass transport. In addition, the sulfur is sticky and tends to cause the mineral particles to agglomerate, effectively halting further oxidation of the particles that end up embedded within the agglomerates. Consumable surfactants, such as ligin sulfonate, have been shown to be effective at avoiding agglomeration, but they are not effective at removing sulfur from the minerals. Hence, their use does not obviate the need for fine grinding."

Jan 1, 2012

By M A. Notte

Sand casting of steel is a process that offers the greatest design flexibility and highest metallurgical versatility. However, competition from other methods of fabrication is quite keen, constantly forcing the steel casting industry to the production of better quality castings at lower costs. New methods and materials have been put to use in the last ten years by foundries everywhere. This paper, in the form of a progress report, deals with new methods, processes and materials used by Canadian steel foundries for regular production, as well as with developments still in the initial but promising stages. T HE casting of steel to shape is the most direct method of producing steel parts in their final form. It is a basically economical process both as to cost and production time; it is also a process that offers design engineers the greatest flexibility and highest metallurgical versatility. In North America, the steel casting market has a normal yearly sales volume of 1,500,000 tons. In decreasing order, the largest customers are the railroads, construction machinery and earth-moving

Jan 1, 1965