Search Documents

By T. M. Waterland

A GREAT deal of work has been done at Britannia during the past three years in improving and standardizing rounds for development headings, and the results obtained have been very gratifying. The round which has recently been adopted as a standard for all drifts and cross-cuts has, in some instances, doubled the average length of break formerly obtained. It has also increased the footage of advance per labour shift and reduced explosives' consumption. At the present time, with a shortage of skilled labour, more control is necessar7 in directing the drilling of rounds. The use of a standard round has been o great assistance to the foremen and shiftbosses. NATURE OF GROUND Most of the ground encountered consists of a moderately silicified chlorite schist, known locally as G.M.S (green-mottled schist). It cannot be termed hard ground, because a three and one-half inch Leyner will drill at an average rate of twelve inches per minute. Due to the abrasive nature of the ground, the gauge of the steel wears rapidly and in most cases one set of steel is needed for each hole. The ground is not 'free breaking and holes must be spaced correctly to obtain a maximum break. DEVELOPMENT OF STANDARD ROUND FOR THREE-SHIFT OPERATION Late in 1940, a development programme was started involving 7,000 feet of drifting, 6 ft. By 7 1/2 ft. In cross-section, in two headings. Plans were drawn up to advance the headings on three shifts. Equipment used in the headings was as follows: D.A.35 Leyner?machines, Eimco Model 12B mucking machines, nine one-ton end-dump cars, one Mancha Little Trammer on the longest heading, 20-pound rail, 4-in. 15 compressed-air line, 15-in. Fan pipe connected to 5 h. P. Coppus fan. Diamond-drill cross-cuts, 16 feet in length, were cut every 250 feet. Switches were installed at these cross-cuts and they served as passing points for the cars. One siding seventy feet in length was cut in each heading at approximately the half-way point. The cycle of operations planned was to muck out, drill, and blast each shift. Previous performance in this type of ground indicated that a daily advance of 12 feet to 14 feet might be made. However, if a better type of round could be developed, an increased daily advance would be possible. A study of the time available for each operation in a net working shift of six and one-half hours indicated that the maximum depth of round that could be mucked, drilled, and blasted each shift would be six and one-half feet. When this maximum depth was decided upon, the next problem was to develop a satisfactory round. Due to ventilation difficulties and to the short net working shift, the whole round had to be blasted at one time. In other words, no blasting of the cut-holes could be done.

Jan 1, 1942

By J. L. Huisman

Bio(hydro)metallurgy is the latest development in the ongoing search for efficient and economic metal winning processes. In addition to bioleaching, other biotechnology-based applications are becoming more and more accepted. In this paper the THIOMET process for general effluent treatment is described. With this process, it is possible to produce sulfide on-site and on-demand and to use the sulfide to precipitate metals, even selectively when required. The process is ideally suited as a treatment to remove metals after, for example, an acid regeneration process. Another process is proposed that deals with stainless steel pickling bleeds. Such effluents typically contain nitrate, iron, nickel, chromium(VI) and other species. This one process handles these compounds, as well as other metals.

Jan 1, 2006

By M. Lebeuf, A. Dumais, C. Farsangi, N. Singh

The Nunavik Nickel project began ramp-up of a new ore body (Expo) in November 2014. This new deposit is significantly more competent than the previous ore type milled (i.e., the plant moved from a feed with a BWI of 12.2 kWh/t to predominantly material with a BWI of 19.6 kWh/t). Despite circuit changes made in advance of the Expo ore ramp-up (grinding media size, mill loading/power draw, and cyclone configuration) the throughput of the plant was bottlenecked at 90% of targeted throughput with multiple stoppages to grind-out the primary mill due to excessive circulating loads. During this time, the secondary milling circuit was under-utilised: therefore the focus for debottlenecking plant production became increasing the product size of primary milling. Given the scope of changes already made to the circuit, it was decided to test the mill in open circuit. The milling changes were modelled using the Molycop Tools package to identify potential problems. In the modelling and plant trial it was apparent that the ball size in the secondary grinding circuit was inadequate, resulting in pebbling. The power draw of the secondary mill was brought up to minimize pebbling and the average ball size was increased. The switch to open circuit primary milling permitted a significant augmentation in plant tonnage. While the overall grinding efficiency decreased using the open circuit configuration, the ability to increase throughput made it the clear operating choice.

Jan 1, 2016

By K. Lillkung, J. Kourunen, M. Latva-Kokko

"Carbon-in-leach (CIL) and carbon-in-pulp (CIP) processes utilize activated carbon to adsorb solubilized gold for recovery. Due to carbon attrition and non-ideal carbon management, however, some of the gold is lost in carbon fines and to the solution. The carbon attrition mechanism inside CIL/CIP reactors is mainly abrasion-related. This is critical to gold loss since gold loading takes place predominantly in the outer shell of the carbon particles. Thus fine carbon dust has a relatively high gold content and such a small particle size that it cannot be captured with safety screens. The attrition rate depends on ore and carbon characteristics, but it is always proportional to the mixing power intensity. This rate can be minimized by continuous suspension level measurement and control of agitation speed. In addition, a novel tank bottom structure can significantly reduce the required mixing power input compared to a flat bottom tank. A major challenge in carbon management is infrequent and inaccurate measurement of carbon concentration in the reactors. In order to reduce soluble gold losses by means of improved carbon management, Outotec has been developing a continuous in-situ measurement for carbon concentration that is tolerant to changes in slurry density.INTRODUCTION Cyanide leaching has been utilized since the late 19th century as a standard technology for hydrometallurgical gold production. Since then, gold and silver recovery rates have increased due to technological development, but very similar recovery methods are still being used. The original recovery method was to use zinc precipitation – similar to the Merrill-Crowe process, which is still common for feed materials with low throughput and high silver content. However, in most cases, activated carbon recovery is preferred due to its improved efficiency. The carbon-in-pulp process (CIP) and its modification, carbon-in-leach (CIL), have a lower residual soluble gold level and are not similarly affected by soluble base metals. The main alternative for the use of carbon is ion exchange resins. The principle of resin processes is similar to the CIL/CIP processes, with a different type of adsorbent material. Carbon processes are usually preferred over resin processes due to the significantly higher cost of resin material and the possibility to use simpler, well-established technology with carbon processes."

Jan 1, 2017

By M. Santaluce

"The revamp of critical process assets that require a significant plant outage (shutdown) presents a unique and demanding set of challenges for plant operators. They are executed in a more complex Brownfield environment, typically with limited working space and often involve unknown conditions or scope. For plant operators, such a project is often a high cost event both in terms of opportunity cost of lost production and the resource cost of labor and materials. It can also be a high risk event in terms safety, environment, and future plant reliability/availability. This impacts current and future performance or Overall Equipment Effectiveness (OEE). In our experience, the sequential nature of the EPCM approach does not provide the proper framework to facilitate the level of coordination, stakeholder cooperation and detailed planning required to adequately address the construction and shutdown complexity of a critical asset revamp projects. This paper proposes a more integrated approach to handling shutdown revamps of critical assets. Its main thesis is to involve the key performing stakeholder groups early in the project lifecycle (engineering team, procurement team, construction team and plant operations) to form an integrated shutdown management team that is focused on ensuring delivered results are aligned with project objectives. In this model, the construction team executing the shutdown/construction is preparing the detailed shutdown/construction planning concurrently with detailed engineering and procurement planning. This allows construction/shutdown requirements to influence engineering and procurement, with the desire to optimize safety, speed, quality and cost. The paper also discusses how to overcome the procurement hurdle in applying such an approach. The outcome of this integrated approach is better planning, coordination, communication and alignment between the project stakeholders, a shutdown/construction driven planning approach that more fully addresses the challenges of these projects and delivered results that are aligned with project objectives."

Jan 1, 2015

By Y. Kashiwaya, J. Yagi, P. R. Austin

The problems of global environment and resources have become important issues in recent years, and the iron and steelmaking industry is requested to decrease energy consumption and carbon dioxide emission. The improvement of efficiency of ironmaking system is one of the countermeasures for these problems because more than a half of total energy input to the integrated steelwork is input to the ironmaking system. Various approaches to improve the blast furnace process have been made. The authors examined their performances through mathematical simulations of blast furnace operation, and confirmed the improvement of blast furnace efficiency under some operating conditions. The ironmaking system consists of various processes, and the materials and the energy are transported among these processes. Thus it is necessary to evaluate the efficiency of the novel operation of blast furnace based on the ironmaking system. In this study, the balances of material and energy on ironmaking system that consists of blast furnace, coke oven, sintering and hot stove processes were analyzed. The operation status of each process in the system was adjusted according to the results of the operation simulation of the blast furnace under novel operating conditions. The analysis clarified the effect of the blast furnace operation on the energy balance and CO2 emission of the ironmaking system.

Jan 1, 2015

By Delio J-J Tortosa, Fred F. Langford

"The Cenex orebody occurs at the intersection of northwest and northeast-trending fault zones that formed during post-Hudsonian uplift. The ore is localized in breccia zones, along faults, and in veins and adjacent wallrocks. The host rocks are Tazin quartzo-fe/dspathic mylonites and ultramylonites and chloritesericite- quartz-graphite-feldspar mylonite schist. The uraniumbearing minerals are finely disseminated pitchblende and uraniferous titanate.The earliest mineralization may have been associated with /ate-stage retrograde metamorphism in the mylonite schist. The main stages of mineralization were associated with brecciation, hematization, carbonatization, and chloritization of the mylonites and ultramylonites. Uranium mineralization was clearly much later than any igneous or metamorphic activity associated with the Hudsonian orogeny.Late post-orogenic uplift, erosion, and deposition of the Martin continental clastics in fault basins were coeval with uranium mineralization. The deposit is consistent with a meteoric-hydrologic system constituting a source for orebearing fluids, hence the close spatial relationship of the uranium deposits in the Beaverlodge area with the basal unconformity of the Martin Group."

Jan 1, 1986

By Ahmad Ghahreman, Lin Li

"In this study, the Fe(II)/Fe(III) redox reaction kinetics on the surface of pyrite, have been investigated in a 0.5 mol L-1 sulfuric acid solution for a temperature range of 22 to 65°C. Based on mixed potential theory, chronoamperometry is introduced to study the Fe(II)/Fe(III) kinetics by subtracting the current density of pyrite oxidation in an iron-free acidic solution from that in an iron-containing solution at the same applied polarized potential. Tafel behavior was established by this method to analyze the kinetics of the Fe(II)/Fe(III) redox reactions. The results showed that exchange current densities increased slightly with temperature, however remained on the order of 10-5 A cm-2. The activation energy for Fe(II) oxidation and Fe(III) reduction on the pyrite surfaces was calculated to be 102.0 and 32.7 kJ mol-1, respectively. Anodic transfer coefficients also increased, from 0.24 to 0.39, with increasing temperature, which indicates a weakened n-type semiconductor property at higher temperatures. Electrochemical impedance spectroscopy measurements have indicated that at lower anodic over potentials the charge transfer is the rate determining step of pyrite oxidative dissolution in sulfuric acid solution. In the presence of Fe ions, the major contribution of the total current density comes from the Fe(II)/Fe(III) redox reaction. INTRODUCTION Pyrite, an abundant sulfides mineral in the nature, is commonly considered a valueless gangue mineral frequently associated with other valuable sulfide minerals such as chalcopyrite, or metals such as gold, or coal (Lin & Say, 1999). Pyrite oxidation has been the subject of extensive research in view of gold metallurgy, as oxidation of pyrite is the initial step to break down the pyrite lattice and expose the encapsulated fine gold particles (Gasparrini, 1983). Fe(III) ion and dissolved oxygen (DO) have generally been considered as the two most important oxidants with respect to pyrite oxidation, having been studied extensively in previous research (Zheng, Allen, & Bautista, 1986; King Jr & Lewis, 1980). The process of pyrite oxidation can be viewed as a series of reactions amongst pyrite, ferrous, ferric and oxygen in which pyrite is initially oxidized by the dissolved oxygen in water forming ferrous (Eq. 1), and then the ferrous also is oxidized by he dissolved oxygen to form ferric (Eq. 2). The ferric, produced by reaction 2, then could potentially oxidize pyrite (Eq. 3) and convert to ferrous."

Jan 1, 2017

By Haibin Ma, Jie Song, Qingyou Han, Xiaoming Wang, Wei Vian

In the grain refinement of aluminum, Al3Ti and TiB2 particles are introduced to reduce the casting grain size down to 200 micrometer level, which makes cold working possible. The particles are brought in by the addition of Al-Ti-B type master alloys. It is generally believed that TiB2 particles are stable and nucleate a-Al grains in solidification in the presence of extra titanium than the stoichiometry of TiB2 from the dissolution of Al3Ti particle in the master alloys. Titanium in solution either form Al3Ti layers on the surface of TiB2 particles or as solute to promote the nucleation and to restrict the growth of a-Al grains. However, a consensus on a grain refinement mechanism is still to be reached due to the lack of direct observation. This paper presents finding on the TiB2/Al3Ti interfaces in an aluminum matrix. It demonstrates a strong epitaxial growth of Al3Ti on the surface of TiB2 particles, a sign of the formation of an Al3Ti layer on the surface of TiB2 particles in grain refinement practice. The Al3Ti layer has a crystal coherency with a-Al and hence offers a substrate for heterogeneous nucleation of a-Al grains.

Jan 1, 2015

By R. Lasmanis, W. C. Utterback

"The Mount Tolman porphyry Mo-Cu deposit is 64 km south of Republic, Ferry County, Washington. It occurs in the composite Keller Butte pluton, which consists of the Keller Butte porphyritic biotite granite and granodiorite, the Mount Tolman quartz porphyry granite, and the Meadow Creek biotite granite phases. The three phases range in age from 61.3 Ma ± 2.3 Ma to 55.7 Ma ±2.0 Ma. The stockwork deposit occurs in the Keller Butte phase above the contact with the Mount Tolman quartz porphyry granite.Mount Tolman is a hybrid calc-alkaline deposit that has features of both a Climax-type and a plutonic type. Prior to post-ore faulting, the deposit had a flattened hood like shape. In plan it is elongated- 1.6 km wide, 3.2 km long, and up to 609 m thick. The orebody has a 292 o strike. It contains a geologic reserve exceeding 2.18 billion tonnes of ore averaging 0.093% MoS2 and 0.09o/o Cu using a 0.048% MoS2 cutoff. Of this total, 816 million tonnes of measured and indicated ore averaging 0.097% MoS2 and 0.09o/o Cu could be mined by open pit with an overall waste-to-ore ratio of 0.91 to 1.The deposit is a stockwork of quartz and quartz-sericite-pyrite veins and fracture fillings that contain molybdenite, chalcopyrite, sphalerite, and magnetite. Five separate episodes of fracturing and mineralization produced the orebody and were followed by four additional episodes of fracturing with sulrgrade mineralization. The Mount Tolman deposit contains propylitic, argillic, phyllic, topaz greisen, and potassic alteration zones. Extensive silicification overlaps the K-feldspathized, quartz-topaz, and phyllic alteration zones."

Jan 1, 1995

By G. Chi, W. J. Davis, S. Watters, D. Hoy, S. Castonguay

"The Poplar Mountain gold occurrence in western New Brunswick is hosted in the Poplar Mountain volcanic complex (PMVC), which is located along the southern segment of the regional Woodstock fault zone. The PMVC consists of three principal units including, in ascending order, a porphyritic felsic volcanic unit, a volcaniclastic unit, and a mafic volcanic unit. U-Pb dating of zircon indicates that the age of the volcanic rocks is younger than 459 ± 3 Ma, and 40Ar/39Ar dating of mineralization-associated sericite indicates that the age of mineralization is 411 ± 3.7 Ma. Gold-mineralized zones occur in all the lithologic units but mainly in the porphyritic felsic volcanic unit. Gold zones are not controlled by individual faults but are characterized by high-density brittle fracturing, thin carbonate-quartz veining, and intensive ankerite-sericite alteration, superimposed on an earlier chlorite-calcite- quartz alteration. Gold is associated with arsenopyrite, which mostly occurs as disseminations in the host rocks, and to a lesser extent with quartz-carbonate-sericite veins and quartz-cemented breccias.Geochemical data indicate that mineralization-associated alteration is characterized by enrichment of K, Rb, Cs, Ca, Sr, Ba, As, Sb, W, C, and S. Fluid inclusion data indicate that the mineralizing fluids are composed of H2O, salts, and CO2 with variable amounts of N2 and CH4; salinities range from 2.3 to 10.6 eq. wt.% NaCl, but mainly from 2.3 to 5.6 eq. wt.% NaCl, and homogenization temperatures lie mainly between 220° and 270°C. Fluid pressures at the site of mineralization are estimated to have been 770 to 1200 bars, corresponding to a depth of 2.9 to 4.6 km at lithostatic pressure. The d18OSMOW and d13CPDB values of mineralization-related ankerite range from +14.5‰ to +16.5‰, and -6.8‰ to -8.3‰, respectively. The d18O values of the ore-forming fluids are estimated to be 6.4‰ to 8.3‰ at a temperature of 250°C. These carbon and oxygen isotope data fall in the field of magmatic fluids and in part the field of metamorphic fluids.Considering the geological setting of the region, abundant granitic intrusions, the similarity between the age of mineralization (411 ± 3.7 Ma) and the nearby Pokiok batholith (402-415 Ma), and the enrichment of granophile elements in mineralization-related alteration, the ore-forming fluids were probably derived from a granitic intrusion underneath the PMVC. These fluids were focused along structures related to the Woodstock fault. The Poplar Mountain gold occurrence might be compared to some granitic intrusion-related gold systems based on the geochemical data presented herein. L’indice aurifère de Poplar Mountain dans l’ouest du Nouveau Brunswick est contenu dans le complexe volcanique de Poplar Mountain (CVPM), lequel est situé le long du segment sud de la zone de faille régionale de Woodstock. Les trois unités principales du CVPM sont, de la base au sommet, une unité volcanique felsique porphyrique, une unité volcaniclastique et une unité volcanique mafique. La datation U-Pb de zircons indique que les roches volcaniques sont plus jeunes que 459 ± 3 Ma, et la datation par la méthode 40Ar/39Ar de séricite associée à la minéralisation assigne à la minéralisation un age de 411 ± 3.7 Ma. Bien que les zones minéralisées en or soient présentes dans toutes les unités lithologiques, on les retrouve surtout dans l’unité felsique porphyrique. Les zones aurifères ne sont pas contrôlées par des failles individuelles mais sont caractérisées par une grande densité de fractures cassantes, de minces veines de quartz-carbonate, et par une altération en ankérite-séricite intense qui se superpose à une altération antérieure en chlorite-calcite-quartz. L’or est associé à l’arsénopyrite, laquelle est principalement présente à l’état de disséminations dans la roche hôte, et à un moindre degré avec des veines de quartz-carbonate-séricite et des brèches à ciment de quartz.Les données de géochimie indiquent que l’alté"

Jan 1, 2008

By F. Baerhold

Recycling of hydrochloric acid from the pickling of mild steel using pyrohydrolysis is a state-of-the-art technology. Recent developments have focused on the production of a high value iron oxide by-product, where the chemical purity and physical properties are the main issues. New processing routes, especially for TiO2 and Ni production, use leaching operations with hydrochloric acid. The feasibility of those processes depends on the availability of an economic and reliable process for the recovery of the acid. Depending on the level and type of impurities and the required specification of the by-product, pyrohydrolysis in a fluid bed or in a spray roast reactor can be the ideal solution. In stainless steel annealing and pickling lines, a mixture of nitric and hydrofluoric acids is used to remove the scale from the surface after heat treatment. Nitrate emissions from the pickling and the rinsing processes have to be avoided because of more stringent environmental regulations. An annealing and pickling line that is totally wastewater-free was developed, where not only the nitric/hydrofluoric acid but also the rinse water, is completely recycled. New developments to increase the HNO3-recovery rate and to obtain a metal oxide by-product that is easier to recycle are presented.

Jan 1, 2006

By H. R. Stockford

"A pyroxenite-carbonatite complex containing extensive pyrochlore mineralization was discovered during January, 1966, within an exploratory license area held by Consolidated Morrison Explorations Limited. Located 32 miles south of Moosonee, Ontario, the deposit was found under 100 feet of glacial till and Paleozoic sedimentary cover using airborne and ground magnetometer surveys. Exploratory and detailed drilling, totalling 47,625 feet in 85 holes, was completed in outlining the deposit to a maximum depth of 900 feet. Pyrochlore reserves are estimated at 62,000,000 tons averaging 0.52 per cent Cb,05 to a depth of 825 feet. Included in this tonnage is a high-grade section containing 10,000 tons per vertical foot grading 0.82 per cent Cb20 5• The deposit is still open at depth and the intrusive complex has by no means been fully explored.The columbium (niobium) mineralization occurs in a lineated calcite-dolomite host rock which has been intruded along a fault zone within a northeast-trending granulite belt. Potassium-argon dating indicates an age of 1655 million years.Preliminary studies suggest that the complex was intruded in a series of pulses in the form of a partially crystallized mush. The James Bay intrusive is unusual in that it is linear in form and contains only two main rock types - p•yroxenite and carbonatite. Nepheline-bearing syenites and associated rocks are notably absent. Moreover, the pyrochlore is essentially non-radioactive and free from many of the impurities generally associated with other pyrochlores. A test shaft to investigate soil conditions and to provide a 250-ton bulk sample was completed during 1968. Subsequent pilot-plant operations indicate that good quality pyrochlore concelttrates can be produced from this deposit."

Jan 1, 1972

By K. C. Corin, Z. G. Song, J. Y. Liu, M. W. Zhang, State Key Laboratory of Mineral Processing-BGRIMM, J. G. Wiese

"In the present study effect of grinding media on flotation of two mineral systems have been investigated, viz. sulphide minerals (including a pure chalcopyrite and pyrite mineral, and two different base metal sulphide ores), and oxide minerals (quartz, hematite and cassiterite). It was shown that mild steel media milling produced lower recoveries in the case of chalcopyrite and pyrite, as compared to the case of milling using ceramic media. For oxide minerals, the effects of using mild steel media as opposed to ceramic media were not as significant as was for the sulphides, although, after mild steel milling, at acidic pHs their recoveries were significantly reduced. For two base metal sulphide ores, viz. Nkomati and Dexing ores, the differences resulting from different milling media , although marginal, were opposite for each of these ores.For oxide minerals XPS showed that oxides and hydroxides of iron (e.g. FeOOH) adsorbed on the surfaces of the minerals. In the case of the Nkomati ore, adding Fe2+ or F3+ ions after milling with chrome steel media resulted in reduced talc (gangue) recovery, but increased water recovery and reduced concentrate grades. Further investigations are currently in progress to examine the Fe ions effect on the talc surfaces and froth properties.INTRODUCTIONGrinding of ores is necessary to liberate the valuable minerals from its gangues to allow for their selective recovery during mineral processing such as flotation. The grinding process inevitably involves contact of the ores with the surface of the grinding device and the grinding media. Accompanied by grinding, several phenomena can occur including the grinding medium wear, formation of precipitated species on the ore surfaces, chemical reaction, galvanic effects, changes in the Eh of solution, etc. There is a considerable body of literature on the differences observed in the flotation of various ores after milling using various grinding media. Laboratory studies have used balls or rods made from mild steel, ceramic, stainless steel or chrome steel to investigate the effects of different grinding media on mineral flotation. It is found that the interactions between the ore and the grinding environment can affect flotation separation of sulphide (Wei and Sandenbergh, 2007; Bruckard, 2011), oxide (He et al., 2014) and carbonate minerals (Song, 2009 and 2010). For example, mild steel milling produces relatively high concentrations of Fe ions in the pulp, affecting the recoveries of minerals compared to the case of ceramic media. On the other hand, the stainless steel media or chrome media are reported to be beneficial to the recovery of sulphides, when compared to the cases of using mild or carbon steel media (Rey and Formanek, 1960; Peng et al., 2003a,b; Huang and Grano, 2006; Bruckard, 2011). It is not clear, however, whether these Fe ions may affect the surface properties of the minerals involved or the general pulp/froth behaviour and hence their floatability. In addition, in the study of an low-S PGE ore carried out by Miettunen et al. (2012), forged media grinding in the CO2 atmosphere led to the highest Pt and Pd grades and recoveries, but the high chrome grinding media gave lower flotation recoveries than those using the forged media."

Jan 1, 2016

By T. W. Wlodek

"AbstractIn this paper a new type of durable 'spiral-rolled' drill set is introduced and its performance discussed. Efficient and economical mine drilling-depends to a great extent on durability of the drill-set employed. Premature failure of this element damages the drill bit and is costly when tungsten carbide bits are used.Time of drilling of 'spiral-rolled' drill sets introduced at present in Canada is considerably larger than for the presently used drill steel, but laboratory simulated service tests and practical field tests show that the 'drilling life' of the spiral-rolled drill set is several times that of ordinary drill steel.Some features of differential plastic deformation and differential surface rolling, so called 'spiral-rolling', are given.Relations between the drilling machine drill set and characteristics of the ore are discussed. The effect of shims on conical drill rod attachments, the mechanism of failure of drill steel, .and stresses during mine drilling, are analysed.IntroductionIN MINE DRILLING operations, the main interests are: the drilling machines as a source of working energy, the drill set as the tool transferring the working energy to the cutting edges of the bit, and, finally, the drilling characteristic of the .ore or waste rock.This paper includes a review of the possibilities of metallurgical and mechanical improvements in the drill set, with particular attention to drill steel and the attachments.For economical and efficient mine drilling operations, a durable drill rod, attachment, and drill bit are essential. Premature failure of any of these parts interferes with mining operations and is costly."

Jan 1, 1955

By J. D. R. Neilsen

The objective of the research conducted and presented herein was to determine the effect of pre-established free gas saturation on the sweep efficiency of an isolated inverted five-spot well pattern. The investigation concluded that the ultimate recovery of an isolated inverted five-spot may be slightly increased by establishing a free gas saturation prior to water flooding; however, of more significance is the extreme deviation of the pattern's performance after water break-through from that commonly obtained from developed well patterns. The rapid "water-out" characteristic common to both linear floods and floods conducted in developed well patterns was not evidenced in the isolated inverted five-spot. Instead, the wells continued to produce oil long after breakthrough until ultimate areal sweep efficiencies of four, five, and six hundred percent were obtained prior to the water-oil ratio becoming excessive.

Jan 1, 1962

By Noel W. Kirshenbaum

Difficulties and costs of transport markedly affect Canadian mineral producers because of distance from markets, weather conditions and rugged terrain. The chemical and physical nature of sulphide concentrates presents additional difficulties in handling and transport, resulting in higher costs which are ultimately borne by the mineowner. Troublesome properties include the thixo-tropic character of wet concentrates, freezing, susceptibility to autogenous heating, and fine particle size causing spillage and dusting losses. Canadian mineowners and shippers must contend with these problems and with stringent regulations governing the maritime shipping of concentrates. A "systems approach," in which complementary techniques in materials preparation, handling and transport are integrated, could reduce freight costs and losses for those selling concentrates, facilitate operations for those carrying and handling them and, in some cases, improve metallurgical processes in smelters receiving them.

Jan 1, 1969

By P. Cavanagh

Summary This paper discusses the fundamental principles which allow the development of a new method for studying the deformation and failure of metals in terms of 'internal microstrains'. Internal microstrains mechanical and magnetic properties are defined and their influence on of metals is outlined. A research programme at present in progress will determine whether magnetic measurements of internal microstrains give sufficiently accurate values for predicting the performance of metals under service conditions. These magnetic test techniques are also being used to detect the beginning of plastic deformation and to trace the development of deformation processes and failure. Results of the experimental work in each field will be published. Introduction Any attempts are being made to develop a complete theory embracing the mechanical behaviour of metals. In spite of the amount of experimental data available, the theoretical approach is rather difficult, since most of the mechanical properties of a metal are determined by deviations from the pure chemical composition or the perfect crystal. Both types of deviation are difficult to reproduce experimentally and to describe theoretically. In general, there are three main avenues of approach to the problem being followed today.

Jan 1, 1950

By J. A. Chamberlain

DURING a recent trip across Canada and parts of the northern United States, the. writer examined some forty mine models. Construction -details and the uses to which the models were being put were outlined in a report to Eldorado Mining and Refining, Limited, and a specific model was proposed on the basis of the Company's particular needs at their Beaverlodge operation. It was felt, however, that portions of the report would be of some value to anyone contemplating building a mine model. For this reason, a synopsis of some of the more important aspects of the problem is presented here, together with a suggested model type that appears to have wide application. Thanks are due not only to Eldorado for permission to publish the following material, but also to the many mine personnel across Canada who allowed the writer to examine their models and gave freely of their time in discussion.

Jan 1, 1958

By C. H. Lee, T. T. Wang

"Exampling of the tunneling task in the Tsengwen Reservoir Transbasin Diversion (TRTD) in southern Taiwan, this study investigates the application of the Drilling Survey System (DRISS) in both Drilling and Blasting (D&B)- and Tunnel Boring Machine (TBM)-excavated sections. In the D&B section, a nonlinear relationship exists between drilling energy and uniaxial compressive strength of rock mass, in which a reasonable coefficient of determination can be analyzed statistically. Additionally, the DRISS accurately predicted an unfavorable section with a valuable position. The magnitude of uniaxial compressive strength back calculated using DRISS data also matches those acquired from geological investigations with different approaches. Study results indicate that the DRISS is an effective tool for fore-probing of both D&B- and TBM-excavated tunnels. INTRODUCTIONModern advancements in geological and geophysical investigations, and drilling techniques, have provided valuable information for detecting and interpreting geological conditions of rock tunnels with a resolution of several to ten of meters (Brückl et al., 2001, 2008, Lorang et al., 2005). Nevertheless, construction risks remain considerable during tunnel excavation, especially when a tunnel was excavated by a Tunnel Boring Machine (TBM). Predictions of the local fault, shear zone, and other minor geological features, which may cause moderate collapse or excessive deformation of rocks surrounding the tunnel, before tunnel excavation is highly desirable for high-quality tunnel construction and economically efficient project management.Rather than conventional geophysical prospection methodologies, which always favor large-scale investigation with moderate precision, this study focuses on the drilling method probing ahead of a tunnel. The goal of such an investigation is not only to prevent catastrophic collapse, but also to provide quantitative or semi-quantitative information for estimation of the mechanical parameters of rock mass.For the tunneling task in the Tsengwen Reservoir Transbasin Diversion (TRTD) in southern Taiwan, a drilling survey system is adopted for fore probing. Data collected from both drilling and blasting (D&B) and TBM-excavated sections are analyzed statistically and discussed. The applications of the Drilling Survey System (DRISS) are addressed accordingly."

Jan 1, 2015