Search Documents

By Shuji Owada

Scrap electrical and electronic appliances, so called "E-waste", are not a present target to be collected and recycled under Japanese regulations. This material, however, contains considerable amounts of base, precious, and rare metals and it is necessary to recover these elements for maintaining stable supply and establishing "the society of environmentally-sound material-cycle". This paper describes recent trends of rare metals recycling in Japan and technological approaches to achieve the above objective. Also a research work to concentrate rare metals from the printed wiring boards by combining brand new comminution and physical separation methods is discussed.

Jan 1, 2011

By Q. H. Bui

The elastoplastic self-consistent model is one of the effective models to study the initial microstructure effect on the mechanical behavior of bulk materials. However, the use of this micromechanics-based model which takes into account only the Hall-Petch relationship at grain level for predicting the grain sized effects on the strength of the deformed materials is not accurate yet because of the fact that the dislocation density contributes also to the strengthening of this kind of materials. In this study, a modification made to the Hill-Hutchinson elastoplastic self-consistent model was proposed for investigating the microstructure dependence of the mechanical behavior of cold-drawn 6063 aluminium tubes. Because of the novel modification, an estimation procedure with two steps was required to identify the parameters of this micromechanical model. An acceptable agreement between experimental and theoretical stress-strain curves was achieved.

Jan 1, 2011

By Takayuki Takasugi, Naoya Masahashi, Yasuyuki Kaneno, Satoshi Semboshi, Yusuke Kadoi

Cu–Ti alloy wires doped with and without a small amount of Ni were fabricated by over-aging and using intense drawing procedures. For both the Cu–Ti alloys with and without Ni doping, the over- aged microstructure was occupied fully with a coarse lamella of Cu solid solution and β-Cu4Ti plates precipitated discontinuously by grain boundary reactions. The full-lamellar microstructure was developed much more rapidly by aging in multi steps at 873 K to 723 K rather than by isothermal aging at 723 K. Ni doping in Cu-Ti alloy was also effective to accelerate the formation of the lamellar microstructure. When drawing the over-aged alloy with inferior hardness but superior electrical conductivity, the strength increased steadily and eventually exceeded that for the wires drawn from the peak-aged alloy. In addition, the electrical conductivity of the wires drawn from the over-aged alloy was always much greater than that from the peak-aged alloy. Eventually, the procedure of over-aging, followed by intense drawing, could enhance both the strength and electrical conductivity of Cu-Ti alloys, whichever they contain a small amount of Ni or not, rather than the conventional peak-aging and drawing process. INTRODUCTION Cu-based alloy wires, which have an excellent combination of strength and electrical conductivity, have attracted extensive attention for highly mechanically stressed electrical devices, such as conductive lead wires and wires in suspension springs. Cu-Be alloys are widely used for such electrical components owing to their combination of strength and electrical conductivity among industrial Cu-based alloys. However, since beryllium is potentially toxic and also a rare element, substitute materials for Cu-Be alloys have been searched for several decades. Age-hardenable Cu–Ti based alloys have been proposed as candidates because their mechanical and physical properties are comparable to those of Cu-Be alloys; however, their electrical conductivity is inferior (Datta & Soffa, 1976; Soffa & Laughlin, 2004). In order to satisfy the requirement of downsizing and streamlining electrical devices, further improvement of the mechanical and electrical properties of Cu–Ti alloy wires is needed. Age-hardenable Cu–Ti alloys, which contain approximately 3 to 6 at.% Ti, are typically prepared using a solid solution treatment above 1100 K and then aging at a moderate temperature of 700 K to 800 K. It has been revealed that the microstructural events during aging progress as follows (Soffa & Laughlin, 2004): (1) compositional modulation of the parent supersaturated Cu solid solution in an initial aging stage (Laughlin & Cahn, 1975), (2) continuous nucleation and growth of fine needle-shaped precipitates of metastable β’-Cu4Ti with a tetragonal structure in a peak-aged stage, and (3) discontinuous precipitation of cellular components laminating the plates of a terminal Cu solid solution and stable β-Cu4Ti with an orthorhombic structure at the grain boundaries in an over-aging stage. It has been also accepted that the highest number density of dispersed fine β’-Cu4Ti needles should contribute to maximal strengthening. On the other hand, decease of the strength in the over-aging stage occurs due to the replacement of the fine β’- Cu4Ti needles with cellular components containing coarse β-Cu4Ti plates, while the electrical conductivity is significantly enhanced due to the depletion of solute Ti in the Cu matrix. This suggests that a combination of strength and electrical conductivity for age-hardenable Cu-Ti alloys is in a trade-off relationship, and that innovative improvement of both properties might be limited to tuning the aging conditions.

Jan 1, 2019

By D. Michaud, C. Bazin, S. Lévesque, L. Pérez-Barnuevo, H. Longuepée

In recent years, with the emergence of Geometallurgy, a great effort has been made to characterize ore resources as early and accurately as possible, to allow better design and a more efficient operation of mineral processing circuits. In this context, core logging plays an important role, since drill cores provide the first insight into the ore characteristics. However, to satisfy geometallurgical requirements, traditional core logging does not suffice. New tools and methodologies need to be developed for the automation of core logging and the acquisition of mineralogical data better related to mineral processing performances. In this paper, a methodology for the geometallurgical characterization of drill cores is proposed, based on the drill core textural patterns. Textural pattern is defined here as the macroscopic spatial arrangement of minerals. The Mont-Wright iron ore deposit (Quebec, Canada) is used as a case study. The first part of this work aimed at analyzing the potential link between the iron ores textural patterns observed in drill cores and their response to ore processing, namely comminution and concentration. Preliminary results show similar performances in terms of energy consumption and heavy liquid separation for samples showing the same textural pattern. In the second part, this work seeks to develop a methodology for the automated identification of drill core textural patterns by the application of digital image analysis and discriminant function analysis. The results obtained show that this methodology is able to discriminate between the textural patterns identified at Mont-Wright with a good rate of success. Therefore, this work lays the foundation for the development of a new drill core characterization tool, which would allow for the early prediction of the iron ore behaviour during mineral processing through the identification of drill core textural patterns.

Jan 1, 2016

By J. Pepin

When using alternating current submerged arc welding (SAW) to produce pipes from microalloyed linepipe steels, it is critical to balance penetration depth and deposition rates, in order to minimize the number of weld passes while still maintaining good heat affected zone (HAZ) microstructures and properties. A series of bead-on-plate (BOP) submerged arc welds were performed on X70 steel, using different waveform variable settings (i.e., balance, offset and frequency). Weld bead cross-section profile deposition and penetration areas were measured, and both Vickers hardness and Charpy V-notch impact testing were performed. Both single electrode and tandem electrode welds were evaluated.

Jan 1, 2011

By Matthew Novak, J. Brent Hiskey

It is well known that when chalcopyrite is put in direct contact with copper in an acidic medium a galvanic cell is created. Chalcopyrite is reduced to iron and sulfur deficient defect phases such as bornite, chalcocite, and at very low potentials to elemental copper. Galvanic conversion experiments were performed using three chalcopyrite concentrates. The first chalcopyrite contained less than 10% impurity phases. The second concentrate had a high concentration of pyrite, and the third concentrate had a high concentration of pyrrhotite. The effect of temperature, acid concentration, chalcopyrite grain size, copper grain size, and agitation on the rate of chalcopyrite conversion was studied.

Jan 1, 2014

By I. M. R. Duarte, J. A. Rodrigues-Carvalho, F. R. S. Rosa, A. B. Pinho

"This paper aims to contribute to the knowledge of the mechanical properties of the shales and greywackes which constitute the flysch-type deposits of the Baixo Alentejo Flysch Group, in the south of Portugal. These formations are flysch-type deposits constituted by sequences of usually thick greywacke beds alternating with thin shale beds, which include sometimes intercalations of conglomerate beds. All the sedimentation of these flysch formations was controlled by tectonics. At the same time, should have occurred along with the first Hercynian deformation phase, a low-grade metamorphic event (chlorite zone), that affected these flysch deposits. This study highlights the influence of anisotropy and heterogeneity of these flysch rocks on their physical and mechanical characteristics. The anisotropy verified in some physical properties and on mechanical properties, due to the foliation makes difficult the sample preparation for the laboratory tests. Besides, it induces a scattering of the properties values measured, as for example, the strength and the deformability. The heterogeneity is related to the main features of these geological formations, which are constituted mostly by thinly stratified greywackes and shale beds, which sometimes may affect the results of the laboratory tests making them less representative. The study is made by using both shales and greywackes that constitute these flysch-type deposits in order to evaluate their geotechnical properties, mainly of the shales. Samples of these two rock materials, are tested accordingly a laboratory testing programme, which includes which included mineralogical analysis (X-ray diffraction), physical tests (bulk density, porosity, and void index) and mechanical tests (uniaxial compression, and deformability tests). INTRODUCTIONOne of the factors that most influence the geomechanical behavior of rocks, as well as rock masses is the anisotropy. The word anisotropy comes from two Greek words ""anisos"" (meaning uneven) and ""tropos"" (meaning direction). A body or material is considered to be anisotropic, where the same property has different values depending in which direction it is measured, therefore, an anisotropic material is one whose magnitude of the properties depends on the direction in which these are studied or measured. Otherwise, it is about an isotropic material. However, the fully isotropic materials are quite rare in nature."

Jan 1, 2015

By M. Maleki-Moghaddam

At the concentration plant of the Gol-E-Gohar Iron Ore Company (Iran) three 9 m × 2.05 m AG mills (fixed speed) are used in parallel in a dry operation. The performance of AG mills has been lower than the target value indicated by an increase in the product size (P80) from 450 µm (target) to 515 µm and low power draw (50% of nominal). By simulation it was found that increasing the liner lifter face angle from 7 to 30o while keeping the original lifter height (i.e., 22.5 cm) could provide an appropriate charge trajectory. When the proposed liners installed in one of the AG mills, the throughput increased by 27%; when 5% (v/v) balls were added the throughput increased by 40%. The product size also decreased from 515 to 501 µm.

Jan 1, 2012

By Fabio Terzi

In this investigation some preliminary results are reported about the electrochemical oxidation of CO using goldbased encapsulated nanoparticles grafted on conducting substrate. The investigation has been planned in four steps: 1. production of Au(111) substrate and modification with self assembled monolayers; 2. synthesis and embedding of nanoparticles; 3. grafting of encapsulated nanoparticles on electrode substrates; 4. investigation of CO electroxidation on the modified electrode. The systems were characterized by means of various techniques (spectroscopic, microscopic, and electrochemical methods), obtaining information about SAM's structure and morphology, size and composition of nanoparticles and electrochemical behavior of modified electrodes.

Oct 1, 2003

By T. Narita

The diffusion barrier coating system (DBC system) was designed to suppress interdiffusion between alloy substrate and coatings in addition to ensuring slow oxide growth at high temperatures. In this report the concept of the DBC system will be introduced, and the results obtained for various heat-resistant alloys are presented. In this DBC system the s-phase of the Re-Cr-Ni system was selected as the barrier and is formed by electroplating Re-Ni and Ni films from aqueous solutions, followed by Cr and/or Al pack cementations. A typical DBC system consists of Ni-base superalloy / triple s-Re based alloy layer / ?’-Ni3Al and/or ß-NiAl (with or without Pt addition) / a-Al2O3. It was found that the DBC system maintained its structure for long time exposures because the s phase has tie-lines with the ? and ?’ alloy substrate and the ?’ and/or ß coating. The s-Re based alloy can suppress both the inward Al diffusion and the outward diffusion of alloying elements. The DBC system was successfully applied to various heat-resistant alloys such as Ni-Mo and Fe-Cr-Al based alloys, and these alloys with the DBC system were creep-deformed slowly under external applied stresses. A simultaneous diffusion coating process for Al and Hf was developed using Hf+NH4Cl+Al2O3 pack cementation. To obtain reliable and long-life coatings the combination of alloy substrate, coating, and external scale should be considered as a total system, to optimize oxidation resistance, structural stability, and mechanical properties.

Jan 1, 2010

By Christian Brits, Bob Blain, Lloyd Buckingham, Juliu Stieger, Jean-Francoi Dupont

Barrick Gold Corporation (Barrick) has undertaken innovative methods of evaluating and improving the performance of grinding mills in several of its operations around the world. The results have been positive with some of the mines showing more than 20% net energy improvement leading to more than 43,000 tonnes per year reduction in CO2 emissions in four of the operations reviewed.

Jan 1, 2012

By Thomas G. Madgwick

Introduction Development of oil and gas is still centred in the Province of Alberta, much as it was when C. C. Ross read a paper on this subject three years ago at the Annual General Meeting in Montreal; but so far as gas is concerned, its early production in Saskatchewan seems now assured. The three years that have elapsed since Mr. Ross' paper have witnessed a growth in the world's production of oil that has created a potential supply out of all proportion to the demand for petroleum products, and one that has resisted the most energetic efforts of the industry entirely to control. The natural result has been very much to retard the active prospecting of new structures in the Prairie Provinces with any immediate view to oil production, although the same factor has not hindered the search for gas to the same extent. One consequence has been to divert the attention of organized oil operators from wildcat drilling to more detailed geological investigation than had hitherto been customary, sometimes accompanied by test drilling with a view to the elucidation of geological structure rather than to the immediate development of production which at the present is not needed. Nevertheless, in spite of the growth of this phase of oil prospecting - which the writer would be the last not to welcome as a very real blessing and of far greater value than indiscriminate wildcat drilling in either the complex structures of the foothills or the simpler but largely concealed formations of the plains- it is most satisfactory to have to record that in these three years the growth of production both of naphtha and the heavier crude-oil has kept pace with the by no means inconsiderable growth in the production and utilization of natural gas.

Jan 1, 1929

By Harold L. Gibson, David H. Watkinson

"Volcanogenic massive sulphide deposits of the Noranda Camp cur throughout the Noranda Shield Volcano but are concentrated and along the margins of the Noranda Cauldron. The deposits are realized along synvolcanic faults that also accommodated subsince and controlled the location of eruptive centres. Deposits within e 3 000 m thick Mine Sequence formed during a period of active volcanism and subsidence coinciding with the onset of two cauldron subsidence cycles. The Noranda Cauldron was a restricted site of 10malously high heat flow and structural permeability that favoured e development of a high-temperature hydrothermal system. Metals may have been derived from leaching of aquifer rocks by convecting a water or directly from a shallow underlying magma chamber, now presented by the Plavrian Pluton, that was at its highest position !thin the crust during cauldron subsidence. The deposits formed rough a combination of sulphide precipitation from exhaled fluid td replacement at and below the seafloor in a manner analogous to ose on the modern seafloor.RESUMESi les dépôts de sulfures massifs volcano gènes du camp minier de ~uyn-Noranda sont présents dans les différentes parties du volcanluclier de Noranda, ils se trouvent concentres toutefois, en plus ·and nombre, sur le pourtour de la caldeira (cauldron) de Noranda. ~s dépôts sont localises le long des failles synvolcaniques qui ont cilite la subsidence et contrôle la position des centres d’éruption.~dépôts situes dans la séquence des mines (3 000 m d’épaisseur) sont formes durant un épisode d' activité volcanique et de subsiden qui coïncide avec l' amorce de deux cycles d' affaissement de la rldera (cauldron) de Noranda. Celle-ci Jut le site exclusif d’unflux : chaleur anormalement élevé et d’une perméabilité d’origine cucturale qui ont favorise le développement d’un système hydrothermal a haute température. Les métaux proviennent soit directement d’une chambre magmatique situee afaible profondeur, so it d’un lessivage des roches de l’aquifère par l’eau de mer circulant par convection. Cette chambre magmatique, représentée maintenant par le pluton de Flavrian, se trouvait à son niveau le plus élevé dans la croute au moment de l’affaissement de la caldeira (cauldron). Les dépôts se sont constitués par un mecanisme combinant remplacement et précipitation de sulfures à partir des fluides exhalatifs, au niveau ou au-dessous du plancher océanique, de la même manière que se forment de nos jours, les dépôts de sulfures massifs au fond des océans."

Jan 1, 1990

By William J. Davis, R. Blair Hrabi, Sally Pehrsson, Amelia V. Logan, Ross Sherlock

"Abstract - The Meadowbank gold deposits are hosted by a series of polydeformed and metamorphosed auriferous iron formations located in the Neoarchean Woodburn Lake group, western Churchill province, Nunavut. The supracrustal rocks in the Meadowbank area consist of a thick sequence of intermediate-composition volcanic rocks with intercalated iron formation, ultramafic volcanic rocks, and quartzite to quartz arenite. U-Pb geochronology gives an interpreted age of 2711 ± 3 Ma for the host strata at Meadowbank.The intermediate volcanic rocks are predominately volcaniclastic and have a geochemical composition that is consistent with an active continental margin setting. Iron formation deposition was coeval with the intermediate volcanism, as indicated by incorporation of volcanic detritus in the chemical precipitate. The geochemistry of the iron formation indicates that it precipitated from a fluid that at one time was at high temperature (>250°C), reducing, and likely acidic. Intercalated ultramafic rocks rarely show spinifex textures and have trace element ratios that are consistent with mantle plume-related undepleted mantle asthenosphere, likely recording episodic mantle upwelling associated with rifting in an active continental margin. The contact between the ultramafic volcanic rocks and the overlying quartz arenite is a disconformity marked by a quartz pebble conglomerate. However, similar geology on the structural hanging wall and footwall of the contact suggests that the conglomerate does not represent a significant hiatus in deposition, and is more likely a prograding terriginous siliciclastic unit.Three metamorphic events are recognized. The first, M1, is a cryptic greenschist facies event that is pre-D2. The second event, M2, is a mid-greenschist to amphibolite facies, syn-D2 event. M3 is the last event recognized, and is a post-tectonic greenschist facies event that is regional but inhomogeneous in extent, possibly reflecting thermal aureoles around post-tectonic 1.7 to 1.8 Ga Nueltin granites. The structural geology of the area is complex with four phases of deformation recognized, two of which had a significant effect on the geometry of the deposit. All of these regional events are interpreted as Paleoproterozoic in age. Relationships between deformation fabrics and mineralization, as well as the overall geometry of the mineralized envelopes, suggest that the deposit formed during syn- to late-D2. Superimposed on the mineralization are D4 structural elements that postdate gold mineralization.The main control on gold mineralization is replacement of magnetite by pyrrhotite and pyrite in high-strain corridors. The composition of amphiboles and chlorites associated with gold mineralization is remarkably consistent and shows no spatial or temporal variation, suggesting that it was buffered by the iron-rich nature of the host rocks. The bulk metasomatic effect on the intermediate volcanic rocks is characterized by the addition of K2O and the loss of CaO, Na2O, and MgO, with little variation in the total iron content. The elemental losses are likely the result of destruction of feldspars, stilpnomelane, and ferroactinolite, which are relatively common in the unmineralized rocks, and the formation of sericite, chlorite, and grunerite."

Jan 1, 2004

By James W. Cameron

DESPITE the fact that, after oxygen and silicon, aluminum is the most abundant and widely distributed element in the earth's crust, it is, commercially, a modern metal. Attempts were made by Sir Humphrey Davy and other chemists to decompose alumina, the oxide, into its elements, but with unsatisfactory results, and it was not until 1827 that Wohler succeeded for the first time in isolating the metal in pure form. Some thirty years later, commercial production of aluminum was started in a plant near Alais, France, using a process developed by Deville which was a modification of that of Wohler. It was not, however, until around 1886 that possibilities of low-cost production were realized. Hall and Heroult discovered, independently, the now famous process for extraction of aluminum by the electrolysis of alumina (Al,O,) dissolved in fused cryolite. This discovery, with its subsequent effect in reducing the price of the metal, was perhaps the greatest single factor contributing to the remarkable growth of the aluminum industry. But only in the years following the Great War did aluminum begin to attain equal importance in many fields with other non-ferrous metals. Numerous factors, political and economic, in the past decade have had a profound effect on the industrial history of the metal. At present, systematic substitution of aluminum for other base-metals is proceeding at a rapid rate in such countries as Germany and Italy with a view towards 'economic self-sufficiency'. Quite naturally, ?the economic depression started extensive research and experiment in various industries in an attempt to improve efficiencies and lower costs. Partial answers have been found in the extended use of aluminum and its alloys. Even against the background of tremendous technological advance that has marked the past fifty years, the rise of the aluminum industry must necessarily stand out conspicuously.

Jan 1, 1939

By Shila Jafari, Mari Lundström, Aleksei Kritskii, Pia Sinisalo

A typical process adopted at nickel plant is the processing of nickel-copper mattes and converter mattes using the following technology: pressure oxidative leaching (POX), solvent extraction (SX), electrowinning (EW), cobalt recovery, and solutions purification. As a result of multi-stage atmospheric and autoclave process leaching, copper-nickel separation is achieved. Cobalt and nickel are further separated by SX. Copper in the process can be removed as copper cake (Cu-cake), which is a by-product with high content of valuable metals. In the current paper, a method combining atmospheric and pressure leaching of Cu-cake in sulfuric-acid media is discussed. Suggested method allows to obtain high copper extraction (>98%), with leach residue containing precious metals and PGMs. Sulfuric acid media was chosen to make the suggested technology adaptable for the primary POX-SX-EW circuit. The initial Cu-cake was analysed and a range of process parameters (t = 25–190°C; PO2 = 0–7 bar) investigated to achieve the optimal conditions for leaching process at the ambient as well as at increased pressure. As a result, an initial process block diagram for the treatment of Cu-cake with high copper leaching efficiency and low metal losses is provided. INTRODUCTION The conventional technology for nickel sulphide ore processing includes the following main stages: froth flotation, matte smelting and converting. The subsequent processing of nickel converter matte is possible using fundamentally different approaches - hydrometallurgical (Llanos, Queneau & Rickard, 1974; Rademan, Lorenzen & Van Deventer, 1999; Kshumaneva, Kasikov, Neradovskii & Belyaevskii, 2009; Dutrizac & Chen, 2013) and pyrometallurgical (Tsymbulov, Knyazev, Tsemekman & Golov, 2007). Hydrometallurgical approach in comparison with pyro-process has several advantages, such as reduced environmental load, reduced PGM losses, increased copper and nickel extraction. Typically, hydrometallurgical technologies include leaching, solvent extraction as well as nickel and cobalt recovery in metallic form by electrowinning or hydrogen reduction or as valuable metal salts via crystallization process (Crundwell, Moats, Ramachandran, Robinson & Davenport, 2011).

Jan 1, 2019

By H. Wotruba, L. von Ketelhodt, M. Kowalcyk, C. Kleine, M. Robben

Sensor-based sorting is a financially and technically viable technique that is operating with little or no water and relatively little power consumption. Sensor-based sorting has already proven its operational stability at two gold applications in South Africa. Sensor-based sorting cannot only turn waste dumps and diluted mining blocks into reserves. The implementation can also cause a decrease in specific operating costs of mill and mine when for example replacing selective mining by bulk mining methods with subsequent sorting. Successful installations, operational experience, test work data and flow sheet integration from mine-to-mill underline the impact and potential that sensor-based sorting can have on the gold mining and processing industry.

Jan 1, 2011

By M. Abdellatif

Successful demonstration of The Mintek Thermal Magnesium Process (MTMP) was achieved in November 2004 at the pilot-scale, About 30 tons of magnesium producing recipe was smelted in the DC arc furnace over a continuous operation of 8-days, Twenty-two furnace batching-tapping operations were carried out at a feed rate of 525kg/h and a smelting temperature of 1600-1700°C, The MgO content in the produced slag was as low as 6,7%, and averaged 9,2% MgO, resulting in an overall magnesium extraction of 77%, which reached 87% during good operating periods, Magnesium vapour was extracted at a rate of 70-85kg/h and was delivered to the condenser that was operated at 680-720°C, The magnesium was captured in the condenser crucible in a liquid state, allowing its prompt tapping, More than 3500kg of crude metal were produced over 15 on-line metal tapping operations, On average, a condensation efficiency of 85% was achieved during the entire testwork, which peaked at 87% during steady operations, The quality of the crude metal was similar to, if not better than, that of the Magnetherm's crude magnesium, A pre-feasibility study has indicated that the MTMP has the potential for lower capital and operating costs as compared to the electrolytic process, and therefore Mintek and its consortium partners are exploring opportunities for a commercial production facility.

Jan 1, 2006

By Jing Chai

The Cenozoic unconsolidated strata with the thickness of 100 to 240m in the east area of China are composed of clay, sandy clay and hardpan, etc. Numerous shafts of the coal mines in these areas have been damaged to various degrees since 1987, with the main reason for this being the subsidence of the super-thick unconsolidated strata. To prevent the continuing settlement deformation of unconsolidated strata caused by groundwater removal, long-term water injection through multiple boreholes controlled the settlement deformation of unconsolidated strata. A new type of fiber Bragg grating (FBG) sensing system was successfully used for real-time strain monitoring of the unconsolidated strata during water injection at a coal mine in China. A mathematical model for the compression settlement induced strain calculation is proposed which can assist understanding of the effect of water injection on the ground. With the increase in water injection, the unconsolidated strata compressed state was improved by the transition of the stress state from compressive to tensile stress. The wavelength change of fiber Bragg grating sensors corresponded with the trend of the water level in the same strata. Engineering practice indicates that these sensors can normally, safely and reliably survive conditions associated with hydrous unconsolidated strata. The FBG sensing can be used for continuous lifetime monitoring of the system, starting with real-time monitoring during low-pressure water injection process of multi-borehole. The results will give important guidance for water injection and mastering stratum subsidence.

Aug 1, 2013

By M. Souley, G. Armand, M. Ghoreychi, D. Seyedi, J. -B. Kazmierczak

"An anisotropic constitutive model is proposed in this paper accounting for both structural anisotropy and induced anisotropic plasticity. It is assumed that the rock is composed of a matrix and of potential planes of weakness. The matrix is assumed to be linear, transversely isotropic and the plasticity is described by a non linear yield function where the parameters are deduced from the nonlinear Hoek-Brown envelopes in pre- and post-peak, and derived from the laboratory characterization. A non-associated flow rule is used with a distinction between compression and extensional stress paths, as well as the absence of volumetric strain beyond large plastic distortion.The planes of weakness are considered as known a priori or assumed to be oriented perpendicular to the direction of the current minor principal stress. An elastic-perfectly plastic behavior according to the Mohr-Coulomb criterion is assumed in the planes of weakness; while the elastic part is considered as linear and transversely isotropic.Finally, the proposed model was implemented in FLAC3D and used to simulate triaxial compressions to provide a verification of the implementation. The applicability of the implemented model to reproduce damage (pre-peak) and/or failure developments around a circular opening is checked. The GCS drift, one of the mine-by experiments set up at the main level of the Meuse/Haute-Marne Underground Research Laboratory, is selected for this first application."

Jan 1, 2015