Search Documents

By Jocelyn Bouchard, Claude Bazin, Sami Makni, Rolando Quispe

"Finely disseminated minerals in ores require intensive size reduction to achieve sufficient liberation for the subsequent concentration process. The use of small grinding media in conventional ball mills as a replacement for the usual 2.5 to 3.8 cm balls (1.0 to 1.5 in) produces a finer size distribution at a lower power drawn by the mill motor. However, the conditions ensuring a successful application of using small media for fine grinding are still not fully understood and some plants faced issues to keep the newly introduced steel charge inside the mill during industrial trials. The retention conditions of small media are investigated in this paper using a continuously operated 40 x 40 cm laboratory grinding mill. The tests assess the effect of the steel charge level, the slurry solids concentration and the feed rate on the rate of ejection of the grinding media. The dominant variable is found to be the filling of the mill with the grinding media, followed by the mill feed rate. Results show that increasing the slurry solids concentration within a grinding mill may be favorable for the retention of the media inside the mill.IntroductionProcessing of complex ores often requires the use of fine grinding to liberate finely disseminated minerals. Grinding requirements for a P80 of less than 0.02 mm are not uncommon, and different grinding mills are available for such application (Leonida, 2014; Pease et al., 2006; Davey, 2006; Orford et al., 2006; Nesset et al., 2006). Even conventional horizontal ball mills charged with of 2.5 cm or larger grinding media can be used for fine grinding. However, simulation (Orford and al., 2006) and plant observations (Alves and L-Bouchet, 2005; Brisette, 2010; Brisette and Roman, 2012) demonstrated the advantages of using smaller grinding media in terms of size reduction and energy consumption."

Jan 1, 2015

By Jose R. Hernandez-Aguilar, Chris J. Martin, Rob Thorpe

"This study presents an approach to establishing relationships between metallurgical performance and the characteristics of the bubble population (gas dispersion) inside flotation cells. Bubble size Db, superficial gas velocity Jg, and bubble surface area flux Sb (Sb = 6Jg/Db) measurements were obtained along with metallurgical samples in full-size equipment processing different ore types. The gas dispersion was manipulated by changing the operating conditions of the cells (gas flowrate and frother type) and the metallurgical performance (grade-recovery) was determined. In two cases, the Sb had a strong relationship with grade and recovery, hence, Sb could be used as practical operating parameter. In another case, Sb did not correlate with recovery. The reasons were attributed to creating small bubbles using frothers with desired anti-coalescence properties. This illustrated that bubble size was the key parameter for metallurgy rather than Sb.INTRODUCTIONUnravelling the mechanisms that govern the relationships between metallurgical performance and the characteristics of the bubble population (gas dispersion) inside a flotation cell remains a major challenge. Information on this subject is scarce in the literature, particularly, plant-scale data. The report of Jameson and Allum (1984) appears to be the first gas dispersion study conducted in industrial (mechanical) cells. To introduce concepts, some aspects of their work are reviewed here.The prime motivation of that study was to establish whether any particular cell design (among 44 cells surveyed) could produce very small bubbles (< 0.1 mm), which laboratory research suggested would increase the recovery of fine particles. Although one of the outcomes was that the (examined) cells did not seem to produce such small bubbles (Sauter mean1 D32 ˜ 0.9 mm), the analysis highlighted the importance of including other factors. Jameson and Allum indicated that, besides bubble size (Db), other characteristics of the bubble dispersion should be considered, namely: gas holdup ?g – the fraction of cell volume occupied by bubbles, superficial gas velocity Jg – is the gas flowrate divided by the cross-sectional area of the cell and, bubble surface area flux Sb – the rate of production of (new) bubble surface area (m2/s) per m2 of cell cross-sectional area. It should be noted that, whereas Jg, ?g and Db can be measured directly, the Sb is derived: Sb = 6Jg/Db, where Db is usually substituted by the Sauter mean diameter (D32)."

Jan 1, 2006

By Ian R. Muirhead

Over the past year or so, a number of mining companies have been meeting to examine the role of research in surface mining and, in particular, how to establish a collaborative research effort for the surface mining industry. A review has been completed which has identified the topics that are of interest to the surface mining companies for undertaking collaborative research. This has identified key subject areas such as Operations & Equipment; Maintenance; Environment & Reclamation; and Stability. Specific research projects for the initial research effort have been selected which include Wireless Data Communications, Analysis and Management; Application of GPS in Mining; and Tires for Heavy Haulers. In addition, attention has also been focussed on finding a suitable low cost, but effective, organization to coordinate and manage the collaborative research. The recently formed CONRAD Organization (Canadian Oilsands Network for Research and Development) appears to be a suitable candidate and discussions are ongoing with that group. This paper provides a summary of the review of surface mining research needs and of the status of the establishment of a collaborative research body for surface mining.

Jan 1, 1996

By T. Holmes, S. Davison

"A surge bin at Agrium’s Vanscoy potash operations has been plagued with flow, wear, and corrosion issues since being built in 1967. The culprits? The bin’s carbon-steel construction, geometry, and the resultant funnel-flow pattern are the root causes. An investigation and cost analysis indicated that hopper redesign and retrofit would increase production and reduce maintenance and capital costs. The retrofitted bin provides safer, more reliable operation and has a much longer predicted working life. Using this example, the authors describe bulk-solids-flow theory and highlight the importance of customizing bulk-material-handling-system design using appropriate flow properties to improve reliability, safety, and cost effectiveness.RÉSUMÉ Depuis sa construction en 1967, un réservoir intermédiaire de l’exploitation de potasse Vanscoy d’Agrium connaît des problèmes de débit, d’usure et de corrosion. Les responsables ? La construction en acier ordinaire du réservoir, sa géométrie et la structure de débit en résultant au niveau de la carotte en sont les causes fondamentales. Une étude et une analyse des coûts indiquaient que la restructuration et la rénovation de la trémie permettraient d’augmenter la production et de réduire les coûts d’entretien et en capital. Un réservoir rénové permet de renforcer la sécurité ainsi que la fiabilité de l’exploitation, et sa durée d’activité prévue en est augmentée. En se fondant sur cet exemple, les auteurs de l’article décrivent la théorie du débit de matières solides en vrac et insistent sur l’importance de personnaliser la conception du système de manutention des matériaux en vrac à l’aide de propriétés rhéologiques adaptées afin d’améliorer la fiabilité, la sûreté et la rentabilité.INTRODUCTIONIn early 2013, Agrium’s Vanscoy Potash Operations (VPO) engaged Jenike & Johanson Ltd. (J&J) to provide testing, consulting, and structural engineering services related to proposed modifications to the 270 t special standard product surge bin, which Agrium planned to undertake during a two-week shutdown in August 2013. The bin, which had been plagued with flow, wear, and corrosion issues for its entire working life, was essential for the continuous operation of two of VPO’s compaction plants and for efficient dispatching to loadout. The bin often experienced product hang-ups, clumping on the walls, and plugging at the hopper outlet. Two recent unscheduled mill shutdowns had been partially attributed to flow issues in the bin due to clumping and product plugging up at the screws. These problems increased maintenance costs, limited production capacity, and degraded product quality. Holes and paper-thin sections in the bin walls discovered during a 2013 inspection revealed the potential for major hot material leaks or even structural failure. Either issue would stop plant operations until the bin could be repaired or bypassed. Clearly, the bin cone had reached the end of its life and required replacement."

Jan 1, 2018

By Bernard Dallaire, Jean Cayouette, Sylvain Duchesne

"Louvicourt Mine's concentrator, located near Val d'Or, Quebec, treats an average of 4,300 tonnes of ore per day composed mainly of copper, zinc, gold and silver. An analysis of concentrator revenues and metallurgical losses shows a potential for additional gain, particularly in regards to precious metals (kustelite) where recovery is usually around 67 -70 %. The planning, installation and trial operational period of two Outokumpu SK-240 flash cells at the underflow of the primary cyclones took two years. The use of (( flash flotation )) technology has made it possible to exploit the favourable conditions at the underflow of the primary cyclones such as precious metal concentration and the presence of liberated coarse chalcopyrite. These conditions permit early flotation (fresh surfaces) of the kustelite and the liberated copper. Since the start-up of the flash cells, the metallurgical gains have turned out to be very positive with increases in metal recovery reflected in appreciable NSR gains. Also, significant savings in reagent consumption and a coarser copper concentrate have made it possible to reduce the drying cycle of the Larox filter presses since the cells were put into operation.BACKGROUNDLouvicourt Mine is operated by Aur Resources Inc. (30% ownership) on behalf of its partners Novicourt Inc. (45%, subsidiary of Noranda Inc.) and Teck Corp. (25%). The mine is located in northwestern Quebec about 600 km north of Montreal and about 25 km east of the mining town of Val d'Or. The mine commenced commercial production in July 1994.The massive sulphide ore deposit lies at depths varying between 450 m and 900 m. Mining reserves (2% Cu equi. cut-off) as of Jan. Is', 2000 are estimated at 7.5 million tonnes of ore averaging 3.4% Cu, 1.8% Zn, 28.0 g/t Ag and 0.9 g/t Au. Delineated ore reserves permit the use of a mechanized transverse blasthole mining method. The extraction order is a typical 1.3.5 mining sequence. Primary and secondary stopes are 15 m wide, 15 to 70 m long (25 m long average) and 30 m high. Backfilling for pillar recovery and regional stability is required."

Jan 1, 2001

By Jérôme Girard, Shiu Kam, Sue Longo

"Historically, tailings management in a northern climate has involved the deposition of tailings into the Tailings Management Area (TMA) as conventional slurry. This type of system is obviously viable but presents challenges that are difficult to manage as circumstances change over the life of mine. These issues can include:? Increases in mill throughput, and? Life of the TMA for the life of mine.This case study will present how thickened, high-density, non-segregating tailings are used as an alternative to conventional slurry disposal to achieve greater storage capacity and enhanced environmental performance for a gold tailings facility in a northern climate. This paper will focus on how this change in deposition strategy accommodated the increased throughput of the mill and the increased life of mine. Specifically, the paper will discuss the addition and integration of new processes to the exiting mill system to accommodate the tailings management issues. It will highlight the challenges from laboratory testing to pre-feasibility to the engineered design of the thickened tailings system implemented at Musselwhite Mine.BACKGROUNDGoldcorp Canada’s Musselwhite Mine, in Northwestern Ontario (120 km north of Pickle Lake), is an underground gold mining operation that began production in 1997. The current mill throughput is about 4000 tpd (1.4 Mtpa). Gold extraction is based on a CIP process with cyanide destruction.The existing tailings management area (TMA) is located about 2 km southwest of the mill complex. The TMA is contained by high ground to the north and to the west and flanged by a moraine ridge along the south side. A number of dams have been constructed along this ridge. The dams were first built in 1996 and subsequently raised in 2000 and again in 2005. Excess tailings pond water is discharged to a polishing pond then released to the environment via a wetland.The TMA was originally designed to contain 13.7 Mt of tailings under a ponded surface for closure. The water cover was to inhibit adverse long-term environmental effects because the tailings contain pyrrhotite and other sulphide-bearing minerals that are potentially acid generating. The design was modified during Stage 3 Construction in 2005 to expand the storage capacity to 17.3 Mt (Golder, 2005). As of end of 2009, over 16 Mt of tailings had been deposited in the TMA. The slurried tailings were historically deposited at 50% solids."

Jan 1, 2011

By Loris S. Russell

THE plains of southern Alberta constitute one of the classic areas of geological investigation in Canada, for it was here in 1874, and in 1881 to 1883, that George Mercer Dawson (1, 2, 3) made the pioneer observations that are basic to all subsequent work on the interior plains of Canada. Dawson&apos;s work was extended eastward by R. G. McConnell ( 4) and northward by J. B. Tyrrell( 5) , but it remained. for D. B. Dowling to re-examine Dawson&apos;s Bow and Belly River Area and to make certain necessary revisions in the stratigraphical system of his predecessor. In 1917, Dowling published his memoir, The Southern Plains of Alberta( 6) , which remained for over ten years the last word on the stratigraphy and structure of the area described. It is generally conceded that Dowling&apos;s work made known the existence of a great artesian basin beneath the semi-arid plains of southeastern Alberta. In addition, his structural studies greatly stimulated the search for natural gas and petroleum. The most recent general publications on this area by the Geological Survey are based on the field work of M. Y. Williams, E. J. Whittaker, W. S. Dyer, and P. S. Warren, between the years 1923 and 1926. Their results were embodied in the Calgary Sheet (7) and the memoir, Geology of Southern Alberta and Southwestern Saskatchewan (8). By this time, the number of geologists working in Alberta in the development of the petroleum and natural gas industries had become large, and in 1931 the Alberta Association of Petroleum Geologist~ offered the Donaldson Bogart Dowling Memorial Symposium on Stratigraphy of Southern Alberta( 9) , a most valuable series of papers descriptive both of the ,surface stratigraphy and that observed in the well records.

Jan 1, 1937

By K. Szafran, R. E. L. Seal, M. Tansey

Conversion of hydraulic equipment to fire resistant fluids has been hampered by less than satisfactory component performance and in some cases, catastrophic equipment failure. Concern over identifying possible causes to these problems led to a joint research project between the Potash Corporation of Saskatchewan Mining Limited and the University of Saskatchewan. This paper summarizes some of the results and conclusions derived from this joint project. In this study, the research was limited to evaluating the effects of potash contamination on the performance of hydraulic equipment. Two separate types of tests were conducted in order to provide a basis upon which trends could be established. This study concluded that the presence of potash dust in the hydraulic fluid can induce severe wear over relatively short periods of time. It was also deduced that a contaminant free fluid combined with proper fluid maintenance could extend the performance of hydraulic components using fire resistant fluids even under very severe operating conditions, such as elevated pressures and temperatures. Recommendations as to how to achieve this goal and the practicality of doing so are presented.

Jan 1, 1988

By Rob Sloan, Simon Yu, Rob Robison, Mark Schmidt

"In 2000-2009, Highland Valley Copper (HVC) tested new generation 660 mm cyclones supplied by various manufacturers in an aim to replace existing first generation 762 mm cyclones without success. Due to plant infrastructure limitations, new generation larger (838 and 800 mm) cyclones were not feasible. In 2010, an approach of testing hybrid 800 mm diameter cyclones was initiated by HVC. The hybrid cyclone consists of an 800 mm cyclone upper head section and the use of existing 762 mm cyclone conical sections. Three hybrid 800 mm cyclones were engineered and fabricated, targeting a throughput of 850-950 mtph and were installed in the E line cyclone cluster. Since starting operation on September 20, 2011, three hybrid 800 mm cyclones have been running at combined throughput ranges of 750 to 1050 mtph. Based on plant Daily Met Reports, the test hybrid cyclones demonstrated a decrease in misplacement of coarse copper bearing material to the cyclone overflow and better cyclone efficiency when compared to the existing 762 mm cyclones at the same throughput. The hybrid 800 mm cyclones also demonstrated significantly higher capacity per unit when compared to the existing cyclones. Based on the improvement demonstrated in the full plant trials, HVC decided to install the new hybrid 800 mm cyclones in all five grinding lines starting in July, 2012. A more detailed discussion of the full plant trials and initial results of the first complete retrofit of E line will be presented. INTRODUCTIONHighland Valley Copper Partnership (HVC) is Canada’s largest base metals mine and one of the world’s largest producers of Cu-in-concentrate. The mine, located in the central interior of British Columbia, is owned (97.5% interest) and operated by Teck Resources Ltd. In 2011, HVC produced about 210 million lbs. of Cu and 8 million lbs. of Mo. HVC’s Mill Modernization Project (MOP), which was budgeted for $475 M, is currently under intensive construction and is scheduled for commissioning in Q1 2014. The following description was valid at the time of writing this paper.The operation has been expanded a number of times since the startup of the original Lornex mill in 1972. The plant started up with two 9.75 m (32 foot) diameter primary SAG mills. It was expanded in 1981 with the addition of a 10.36 m (34 foot) diameter SAG mill. In 1988, the Highmont concentrator grinding mills and flotation section were moved and attached to the Lornex mill site. This added two10.36 m (34 foot) diameter AG primary mills to the Highland mill. This brought the total number of primary mills to five referred to as Line A, B, C, D and E: three SAG mills (A, B and C) each with two ball mills in parallel and two AG mills (D and E) each with one ball mill. Each AG mill line is equipped with one short head pebble crusher. Ball mill circuits are classified using 8 clusters of ten Linatex 762 mm cyclones to reach a target P80 330 micron (equivalent 43% +100 mesh), before the cyclone overflow product advances to the bulk flotation circuit."

Jan 1, 2013

By Jeffrey L. Pagnutti

Train derailment can lead to loss of capital, damage to the environment, and loss of life. Machinery condition monitoring techniques can be used to develop a structural health monitoring system for railway track to detect faults at the incipient stage, before catastrophic failure occurs. This study uses vibration measurements from a novel material haulage unit to develop a decision support system for railway track maintenance. A variety of feature sets and classifiers were compared to determine the optimal configuration for fault detection. The results highlight the shortcomings and advantages of certain methods and describe the process in which the optimal result was obtained. The Parzen data descriptor paired with a refined statistical feature set performed the task of fault detection with less than five percent false positive and false negative classification error. Overall, the outcome of these experiments indicated that condition monitoring of railway systems is a promising approach for fault detection and has the potential to avoid catastrophic failure.

May 1, 2013

By Pathies Nawej Muteb, Tom Strombotne, Karl Leetmaa, Irma Gabric, Keith Darby

"Continuous control of the final grinding product size is important to optimize gold liberation for Gold Milling operations. At Meadowbank Mine an on-line Particle Size Monitor has been employed successfully to achieve the targeted final grind which leads to optimizing the gold recovery at maximum grinding circuit throughput. The live monitoring of the final product particle size leads to a maximum grinding circuit throughput every minute during the process. This paper discusses the optimal utilization of the Particle Size Monitor to assist the Mill operator to maximize the grinding circuit throughput as the milling conditions change due to variable ore processed at Meadowbank Mine. Also the paper includes the usage of the Particle Size Monitor to guarantee the final grind target at each instant of the process.IntroductionAgnico-Eagle is a Canadian-based company that Trades on the TSX & NYSE (AEM). It owns eight mines (8) operating in Nunavut, Quebec, Finland and Mexico and has more than 7,500 employees (Figure 1). 1.6 M ounces of gold were produced in 2015 and the annual average annual production from 2016 to 2018 is forecast to be approximately 1.53 million ounces of gold.The Meadowbank Mine is located in Nunavut, Canada (Figure 2). The mine opened in 2010 and from 2010 to 2014 a total of 1.8M oz of gold was produced. The milling rate is 4.2 Mt per year with an average mill throughput of 11,900 tpd or 496 tph. Average annual gold production over life of mine is expected to be 450,000 ounces. Meadowbank has 775 employees, of which 265 are Inuit or 36% of the total workforce. Estimated life of mine is 2010 to 2018. Gold production in 2015 was 381,804 oz. Meadowbank was Agnico-Eagle’s largest Gold producer in 2015."

Jan 1, 2017

By Alan Jessop

A small group has been set up at the Dominion Observatory, Ottawa, to make a survey of terrestrial heat flow throughout Canada. Terrestrial heat flow is the heat rising from the interior of the earth and escaping at the surface, and is calculated from a knowledge of under-ground temperature distribution and the thermal conductivity of rocks. A small number of diamond drill holes are being sunk for the purpose of measuring temperatures below the surface, but the program is inadequate for a thorough survey. Mines and holes drilled for other purposes are being sought by the Dominion Observatory group to supplement their own drilling program. F ROM January, 1.962, to December, 1964, geo-physicists of many nations will be cooperating in the "International Upper Mantle Project." Unlike tl1e International Geophysical Year, which was mainly concerned with the fluid layers surrounding the earth, the Upper Mantle Project is an intensive study of the solid earth. Canada, with its large land area and extensive Precambrian Shield, is an active participant in the project.

Jan 1, 1964

By R. Kwiatkowski

Agenda ? Health Canada Protocol _ Screening Level Risk Assessments (SLRAs) Contaminants Foods Exposure Pathways COPCs _ Site Specific Risk Assessments (SSRAs) In-depth, quantitative Monitoring Exposure estimates Food Issues in Environmental Impact Assessments ?Country Foods? ? Foods gathered from the project area and consumed by local residents.

Apr 1, 2005

By B. H. Kim

It is hypothesized that the standard approach adopted to characterize the ground and to determine the rock strength properties at depth are flawed and generally tend to underestimate the rock strength and possibly the stiffness, particularly when the rock mass is characterized as massive to moderately jointed or blocky to very blocky. It is therefore necessary to conclusively established that the hypothesis, that the rock strength in highly confined rocks is greater than generally anticipated, is actually valid and generally applicable, and then to develop new procedures to establish rock parameters that can be reliably used for the design of deep excavation.

May 1, 2009

By Paul Semple

"In 2007, Noront Resources Inc. discovered the high grade nickel copper PGE deposit in northwestern Ontario in a region now known as the Ring of Fire. Since the initial discovery, Noront has advanced the Eagle¹s Nest Project and in September 2012 released a feasibility study for the development of the Eagle¹s Nest Project. This paper summarizes the results of this recent study and outlines additional work planned in the next stages of project development. INTRODUCTIONThe following paper summarizes the findings of the recently completed feasibility study on Noront Resources Ltd.’s Eagle’s Nest Project. The feasibility study was compiled into a NI 43-101 report by Micon International. This paper is intended to summarize the major technical findings and for complete information, interested parties can find the entire NI 43-101 report at www.norontresources.com or on SEDAR.LOCATIONThe McFaulds Lake project area, which includes the Eagle’s Nest deposit, is located at approximately UTM 5844000 N and 547000 E, and between approximately 52º42’ and 52º50’ N latitude and 86º06’ and 86º24’ W longitude, approximately 250 km west of the community of Attawapiskat on James Bay and 575 km northwest of Timmins. The closest all-season accessible community to the McFaulds Lake project area is Nakina, 300 km to the south, where there is a paved airstrip, in addition to all weather road and railroad access (see Figure 1).The First Nations communities of Webequie and Ogoki/Marten Falls are located 90 km west and 120 km south southeast of McFaulds Lake, respectively. Both communities are served by regularly scheduled air service, primarily from Thunder Bay; both Thunder Bay and Timmins serve as support centres for the James Bay communities and the exploration projects in the area."

Jan 1, 2013

By Jon R. Maki

"EVTAC, an iron ore mine in Minnesota, had trouble meeting the customer’s pellet silica requirements. In addition, the mine plan was moving towards a lower grade ore and funding was not available for plant improvements to compensate for the change in ore or improving quality. Small changes to optimize various processing equipment resulted in significant improvements in both quality and productivity; for example, productivity on one mill line increased by 10% while producing lower silica concentrate. This paper will provide the methodology that allowed EVTAC to improve quality and productivity through process optimization with little capital investment.INTRODUCTION EVTAC, an iron ore mine in Minnesota, had trouble meeting the customer pellet silica requirements. In addition, the short-term mine plan was changing to a lower ore grade. Because of limited funds, EVTAC did not have the capital for investing in the plant to compensate for the ore change or to make improvements to lower product silica levels. Small changes to optimize process equipment resulted in significant improvements in quality and productivity; for example, one mill line feed rates increased by 10% while also producing a higher quality concentrate. These changes were sufficient enough to allow the mine to lower the target ore grade beyond their initial goal. At one time, a $3M flotation facility was considered as a way to meet quality with the new ore grade. However, the process changes were able to accomplish the same silica reduction with roughly a $50,000 investment in VFDs for sump controls. This paper will discuss some of the modifications that allowed EVTAC to meet the quality and production objectives with little capital investment. It also discusses the methodology used to make these process improvements."

Jan 1, 2014

By Glenn Kosick, John Starkey, Glenn Dobby

"A practical new test has been developed for SAG hardness determination. Using two kilogram samples of minus one inch diamond drill core or crushed muck samples, the Starkey SAG Test has been shown to give accurate predictive information which directly relates to on-stream SAG mill performance. Typical results and test criteria are discussed in the paperAchievements to date include:• Identification of hardness profiles and the location of hard and soft zones in a large ore body.• Accurate prediction of the hardness of a bulk sample by using an adjacent diamond drill hole.• Derivation of a plotted curve relating pilot plant power to laboratory relative hardness.• Demonstration that for every test done to date, the Starkey SAG Test produced a product size distribution identical to that produced in a pilot plant or full scale plant SAG operation.This test can now be used for blast hardness monitoring and short term control of mine production in existing plants and for identifying the proper locations for bulk samples in new projects. In addition, new SAG mill design can now be rationalized in a low cost way to eliminate unforeseen production shortfalls.IntroductionThis paper is presented to introduce the Starkey SAG Test, a practical new laboratory tool for measuring the relative hardness of small ore samples in a semi-autogenous grinding (SAG) environment. The test was first designed for use on diamond drill core samples during the prefeasibility stage of new mining projects, to provide new information about the ore body at reasonable cost. It is a new tool and does not replace existing pilot plant test requirements.The test will also be useful for throughput prediction in existing SAG plants by assisting in short and long term mine planning, where forecasting of metal grades and milled tonnage is used to control mine profitability. Because in-plant hardness testing has previously been unavailable on small samples, this test offers exciting possibilities for SAG mill operations where hardness variation is or could be a problem.The Starkey SAG Test provides the following benefits to the mining industry"

Jan 1, 1994

By S. Kelebek, E. Yalcin

"Two composite samples of a gold-bearing ore from North Western Quebec (Barry Township) were tested to assess their grindability, recovery by flotation and Knelson concentrator as well as extraction using cyanidation.Work index values (BWi) for two composites were found to be 10.4 and 11.0 kWh/tonne, respectively. Flotation tests involved feed samples for which the particle size ranged from a P80 value of 205 ?m to 53 ?m, which resulted in gold recoveries of 91.8% to 95.8% (at gold grades of 130 to 140 g/tonne). Cyanidation tests indicated gold extraction levels ranging from 94.2 to 97.5%. Higher, recoveries were obtained at finer grind sizes and higher cyanide strengths. However, the grind size had a bigger impact on gold leaching. Gold grade and recoveries obtained with the Knelson concentrator device were lower than those obtained by flotation. Mass recoveries to concentrate products strongly depended on the fluidization pressure used. High gold recoveries can be obtained generally at low water pressures of 3 to 4 psi. Higher water pressures produced more selectivity at the expense of higher gold losses.It can be concluded that the gold ore samples tested have good characteristics due to moderate levels of energy requirement, high gold recoveries and extraction rates attainable.INTRODUCTIONBench scale testing of ore samples is an important step in the long series of metallurgical and economic studies involved in bringing new ore bodies into production (Coleman, 1980). Through a laboratory testing program, the behaviour of an ore in a particular process on a larger scale can be established. In an exploratory manner, this testing can be helpful for classification of ores in terms of “good ore” or “problematic ore” by providing preliminary information on recoverability of target minerals. Potential problems if any can be assessed by further investigation of products (e.g., middlings) obtained as a result of testing. A detailed bench scale experimental program in the metallurgical laboratory can also provide the background work for flowsheet development. Depending on the simplicity or complexity of the ore to be tested and type of details required from a testing program, the amount of samples required in the mineral processing laboratory can vary from several kg to more than one hundred kg depending on how detailed the metallurgical testing program is."

Jan 1, 2008

By Jennifer Pell

Dunsmuir Ventures? Nanuq diamond project is located approximately 250 km northeast of Baker Lake and 170 km north of Chesterfield Inlet. It occurs at the intersection of the Wager Bay shear zone with the Keewatin Arch, a major long-lived crustal uplift. The newly discovered diamondiferous kimberlites at Rankin Inlet, Repulse Bay and on Melville Peninsula also occur along this arch. Kimberlite indicator mineral (KIM) sampling has outlined a distinct KIM train more than 35 km long and 6 km wide. Geomorphological studies, boulder displacements and dispersion of magnetite in tills suggest that glacial transport distances were on the order of 4 to 6 kms only. The presence of multiple sources within the main Nanuq indicator train would account for its length and breadth. A second train has been located on the west central part of the property and anomalous concentrations of KIM occur elsewhere. Pyrope garnets (G9?s and G10?s), diamond inclusion field (DI) eclogitic garnets and DI chromites were confirmed by microprobe analyses. Clinopyroxene thermobarometry indicates a cool geotherm, approximately 35 mW/m2, and that mantle within the diamond stability field was tapped. An aeromagnetic survey has identified a number of anomalies. Those with down ice KIM support will have ground geophysical follow-up and will be tested in a spring 2004 drill program. Dunsmuir is optimistic that this will lead to the discovery of a new kimberlite cluster on the Nanuq property.

May 1, 2004

By J. E. Nesset, F. Rosenblum, J. A. Finch

"The self-heating of sulphides can be a major hazard in mining operations and concentrate handling, particularly during transportation and associated storage. Self-heating results from the oxidation of sulphide minerals and can vary from being insignificant to highly reactive and potentially hazardous to both humans and infrastructure. It is essential that there be a reliable test methodology that can measure and categorize a given sulphide material as to its self-heating potential. By their nature, sulphide ores and concentrates are complex and variable mineral mixtures making it difficult to predict their self-heating behaviour a-priori based on mineralogy or with a simple “snapshot” test. Furthermore, self-heating behaviour will depend on the state of oxidation of the sulphides as well as time, temperature and humidity. A review of available testing apparatuses and protocols that can be used to assess self-heating potential is presented. Each of these methodologies was examined in relation to its ability to measure and reliably predict the latent self-heating hazard of a sulphide material. Several of the methods were tested and compared to illustrate their strengths and weakness. The results indicated that a number of the test protocols may produce false negative indications of self-heating potential, constituting an obvious concern to the industry.INTRODUCTION Sulphides as well as other materials (coal, wood chips, hay, powdered milk, to name a few) that are stockpiled in an air atmosphere may undergo oxidation reactions which can result in the evolution of heat (Beever, 1984) (Hudak, 2002) (Blanchard, 2007). If the rate of heat generated exceeds the rate of heat dissipation, the stockpile temperature will rise, potentially leading to “hot spots” in the most reactive areas, and possibly even fires. The heat generation rate, the “self-heating” rate, depends on many factors such as the type and composition of material, particle size, moisture content, oxygen availability, ambient temperature and humidity, and of prime importance, the extend of prior oxidation, or more specifically, the presence of oxidation products. The desire of operators that mine, process or transport sulphide-bearing materials with a potential for self-heating is to have an accepted and reliable method for evaluating and quantifying the potential hazard of their material. The challenges are how to best measure the self-heating properties of given samples, and based on results, predict the behaviour of the bulk material over time and in-situ. Generally, when evaluating a given material one derives the self-heating characteristics of that sample at the time and under the conditions of testing, which will be referred to as a “snapshot test”. If that material is invariable, i.e. it will not change its response over time, then it may be considered to be a “predictive test”. However, if as a result of continuing oxidation or other changes, the material becomes more or less reactive with time, then a “snapshot test” is unreliable with respect to predictive ability."

Jan 1, 2014