Search Documents

By D. Cronin, A. Plumtree, A. Hosseini

"Crack in corrosion (CIC) linepipe defects are hybrid defects not directly addressed by existing assessment methods. To investigate the collapse pressure of these defects, CIC defects were formed in 508 mm (20 in) diameter, 5.7 mm thick API X52 linepipe. These defects were 200mm long and varied in depth from 3.0 to 3.8 mm. The respective failure pressures decreased from 14.3 MPa for the plain pipe to 7.9 and 6.2 MPa respectively. A standard FAD method was applied to evaluate these defects as equivalent length and depth cracks, predicting the rupture pressure conservatively by 18% on average. However, when assessed as equivalent cracks with a reduced wall thickness corresponding to the corrosion depth, the predicted collapse pressures were more accurate, approximately 14% conservative on average.INTRODUCTIONPipelines are a safe and efficient method for transporting high volumes of oil and gas. However, aging pipelines may experience defects, such as cracks or corrosion. Present approaches include detection, assessment and repair of defects before they may become critical to the integrity of the line. There are different codes and standards for assessing pipeline defects, depending on the type of defect, with API 579 (API, 2000) being the most common code for the assessment of cracks in oil and gas pipelines . Corrosion is commonly assessed using RSTRENG (Kiefner & Vieth, 1989). Other methods such as the Finite Element method and the CPS method (Cronin & Pick, 2002) may be used for crack and corrosion, respectively.At present, there is no specific method or procedure for assessing crack in corrosion (CIC) defects, and as a consequence there is a need to provide an assessment and evaluation of the integrity of these defects in order to determine the requirements for defect repair or hydro line testing. Hence, the goal of this study was to provide guidance for the assessment of CIC defects for linepipe.CRACK IN CORROSION DEFECTS (CIC)Significant amounts of corrosion and cracking are not generally found together (Hosseini, 2010). However, a new hybrid defect including cracking within corrosion (CIC) has been identified in operating pipelines. In this case, cracking coincident with corrosion (schematic shown in Figure 1) provides the motivation for the current study."

Jan 1, 2012

By V. S. Sastri, M. Elboujdaïni

"Corrosion rates of silicon brasses, highzinc yellow brass, low-zinc yellow brass, leadedtin bronze and silicon bronzes in both permanent-mold and sand-cast conditions were determined in soft water of pH 3, 5 and 8, and hard water of pH 8 at 70°C by electrochemical polarization technique. The alloys in permanent- mold condition showed greater corrosion resistance than sand-cast condition. Corrosion rates obtained from weight loss measurements showed no observable trend of a difference between permanent-mold and sand-cast alloys.The corrosion rates decreased with increasing pH of the medium. Silicon bronze and silicon brass showed high corrosion resistance while leaded-tin bronze showed the least resistance. Addition of small amounts of aluminum improved the corrosion resistance of silicon bronzes and silicon brasses. Alloys in permanent- mold condition showed greater resistance to dezincification than sand-cast alloys when average pit depth parameter is considered."

Jan 1, 1997

By L. M. Pidgeon

"Part I. - PrinciplesIntroductionIf the oxides of the metals are listed in decreasing order of the magnitude of their heats of formation, the list appearing in Table 1 will be formed. It will be apparent at once that this is essentially the well-known electrochemical series (Table li). The metals at the bottom of the list exhibit great stability and are attacked only by the most violent of chemical reagents. Higher on the list, the metals become more reactive until, at the head of the list, the metals lithium and calcium are unstable in moist air.The reactive metals to be considered lie above manganese. In this group will be found familiar and abundant metals such as aluminium and magnesium, the unfamiliar yet abundant metal titanium, the rare and mysterious metal beryllium, and others of greater or less interest.While these metals exhibit properties as unlike as those of uranium and magnesium, they have in common a specialized and difficult extractive metallurgy. They form compounds of great stability, and their reduction is to varying degrees difficult. The position of a metal in Table 1 (and more particu1arly its position in the free energy column) gives a numerical value to this property.Oxides with low free energies of formation may be reduced with great ease; thus silver and mercury may be produced from their oxides by simple heating in air.Lead, iron, and zinc may be separated from their oxides by heating with carbon to moderate temperatures. Magnesium oxide, on the other hand, .requires a high temperature and very special conditions before it will yield magnesium metal."

Jan 1, 1950

By K. Chattopadhyay

Fluid flows in metallurgical reactors play a vital role on liquid metal cleanliness for both ferrous and non-ferrous metallurgy. Thus, it is absolutely critical to understand different fluid flow mechanisms, and the use of computational methods to model the complex non-isothermal, turbulent, single- and multiphase-flows, has to be appreciated. The present case study emphasizes on controlling the flow of liquid steel in a tundish and enhancing liquid metal cleanliness. CFD modeling was used to build a robust mathematical model, and effects of flow control furniture and non-isothermal conditions were analyzed. The mathematical model was validated against water model experiments. Parameters that were conducive for inclusion removal were identified and implemented in the plant. Some flow control devices could increase inclusion removal to a great extent compared to the existing configurations. In cases, where a hot ladle was poured into a relatively cooler tundish, inclusion removal was better, whereas results were catastrophic in cases where colder liquid was poured from ladle to the tundish. Similar techniques can be applied for other liquid metals including light metals and non-ferrous metals.

Jan 1, 2015

By Habib Zughbi, Paul Zulli

"A key step towards sustainability in iron and steelmaking is to optimise the use of raw materials and energy consumption, and consequently minimise CO2 emissions. Models based on a Process Integration (PI) approach play a key role in evaluating various scenarios and the impact of introducing changes in raw materials and operational conditions on the overall energy consumption and CO2 emissions. BlueScope uses a PI based comprehensive model for its Port Kembla Steelworks (PKSW), called the Integrated Steelworks Energy and Emissions Model (ISEEM). ISEEM is tightly coupled to the configuration of PKSW. It is based on mass and energy balances as well as thermodynamic relationships. ISEEM is a steady-state model and is used to predict overall and detailed unit-by-unit energy consumptions and CO2 emissions. It is also used for plant-based scenario modelling. This paper investigates the impact of major changes to PKSW configuration, including the shutting down of a blast furnace and cokemaking battery, on the energy consumption and CO2 emissions of the plant. It discusses some of the issues involved in updating the model and some identified opportunities."

Jan 1, 2015

By Shiqiang (Rob) Hui, Jiaren (Jimmy) Jiang, Rees Llewellyn, Yongsong Xie

Wear has been estimated to cost the Canadian mining/mineral processing industry over $15 billion per year mainly for repair/replacement of worn parts in 2013. The associated production loss is difficult to quantify but add considerably to the problem. The Canadian oil sands sector which has to deal with extremely abrasive and erosive solids, has traditionally incurred extremely severe and often unique attack. Demonstrable progress in mitigating the wear problems has been achieved through materials development, more informed materials selections, and better component and operation condition designs. An integral contributor to these advances is a long-term collaborative research partnership between NRC and the mining/supply industry. In this paper, this continuing collaboration will be described. A main focus is to identify degradation mechanisms occurring in the most severe and important service applications and to correlate these findings with laboratory test data. Relevant abrasion and erosion (often combined with corrosion) properties have been established and correlated with composition and microstructures for all classes of resistant materials ranging from relatively soft elastomers to ultra-hard ceramics. A comprehensive wear properties database has been compiled. This capability has been instrumental in facilitating the development of improved materials, optimizing materials fitness/selection for service, wear failure analysis, and quality assurance.

Jan 1, 2015

By F. T. Mooney

Introduction The Flin Flon mine of the Hudson Bay Mining and Smelting Company, Limited, is on the interprovincial boundary between Manitoba and Saskatchewan, about four hundred miles north of the Canada-United States boundary. The orebodies are gold, silver, zinc, and copper replacement deposits occurring as irregular lenses of massive sulphides, arranged en echelon, and irregular masses of disseminated copper sulphides in chlorite. The country rocks are of Precambrian age, dominantly lava flows. Development of the Mine The mine is opened by two vertical main shafts- the North Main and South Main shafts- 3,800 feet apart. The North Main shaft has a depth of 2,210 feet and the South Main shaft is completed for stoping operations to the 3,250-foot level (see Figure 1). These shafts are connected by main haulages driven, on the footwall side of the orebodies, at 520-foot intervals down to the 2,210-foot level. No. 3 (subsidiary) shaft is on the footwall side of the orebodies at a point between the North Main and South Main shafts, 2,400 feet south of the former. It has a depth of 3,250 feet and connects with all main haulage levels- with both Main shafts down to the 2,210-foot level and with the South Main shaft on the 2,750-, 3,000-, and 3,250-foot levels. Other openings tO the mine include B North fan raise, the opening due to the recovery of the open pit sill pillar, and several back-fill raises.

Jan 1, 1949

By W. J. Langford

"Conventional design criteria assume that the fracture strength of a structural material exceeds its yield strength. Fracture below the design load is not expected, y et many structures have failed in this way. The causes of the fractures are almost always discontinuities such as cracks and welding defects. Linear Elastic Fracture Mechanics (LEFM or simply 'fracture mechanics') provides an analytical framework for assessing the influence of sharp defects on the load-bearing capability of a structure. Fracture mechanics techniques have reached the point of acceptance by ASME Design Codes for nuclear components, and ASTM Standards now include well-defined rules for measuring fracture toughness. Starting with a simple equation which relates applied stress and crack size, the influence of the material's thickness and yield strength can be calculated. Thus, the size of defect which will cause failure under the applied stress may be determined. Armed with this information, the metallurgist can assess the safety of a structure from the viewpoints of non-destructive testing standards, construction standards and conditions of operation throughout its service life."

Jan 1, 1976

"Developing markets for western metallurgical coal have continued to stimulate considerable exploration activity in the Rocky Mountain foothills and to influence major segments of a wide-ranging carbonization R&D pro-gram. Adjunct studies have included expanded petrographie investigations.Coal preparation has• been principally directed toward utilization of prepared small coal and was, like much of the year's combustion work, strongly influenced by concern over atmospheric pollution. Particular attention has been given to desulphurization and to the suppression of pollutants in combustion systems.In the area of non-fuel utilization of coal, interest has centered on plant nutrients and on a series of coal-based carbons which, inter alia, possess utility as filtration media.Other projects included the development of improved sampling and analytical methods, investigations into the effect of storage on coal proper-ties and R&D in solids pipelining. In addition, a significant volume of basic 'uncommitted' research has been maintained."

Jan 1, 1968

By J. Thiriar

The electrolytic tan/chouse at CCR was recognized by management as lagging behind modem refineries in terms of productivity, energy efficiency and controls. The operation was also burdened by high maintenance costs of cells, floors and electrolyte recirculation systems. A bench marking program was started in 1986 to evaluate processes and other technology by visiting major copper refineries in North America, Europe and Japan. The basic principles necessary to optimize the operation were defined, and a program called CCR 2000 was prepared for approval of the necessary capital investments. This paper describes the results obtained to date and outlines the remaining work to complete the modernization program, in particular, the control of electrolytes, the elimination of the Baltimore groove and studies to modernize the stripping operation or adopt permanent cathode technology.

Jun 1, 1993

By Carlos Rebolledo, Nelson Parra

Arsenic is an unresolved problem in the mining industry considering the fact that most of the new copper deposits have high arsenic contents; stricter environmental restrictions for handling, transporting and processing complex materials are expected and stable abatement of arsenic is not extensively applied. In 2018 Chile produced 24.5% of the total copper from concentrates and in the future copper production in Chile is expected to increase, mainly associated with production of concentrates that will also contain more arsenic. China has set an import benchmark of maximum 0.5% for arsenic content in copper concentrates and this value is expected to be more restrictive in the future. On the first day of 2018 China banned the importation of scrap. Blending practice has been a business option, but it is not sustainable in the future, as “normal” copper concentrates become less and less clean. By the end of 2018, Chile formulated new regulations, increasing the capture of SO2 and arsenic to 95%. In order to comply with these regulations Chilean smelters had to make large invest large amounts of money. Disposing of arsenic as a stable residue is a pending issue. EcoMetales is a 100% subsidiary of Codelco and provides the mining industry with environmental solutions. It has a plant near Calama in Chile that treats flue dust from smelters, refinery effluents and acid solutions from acid plants. EcoMetales is fully committed to contributing to the solution to the arsenic problem. Currently we are developing four main projects: 1) Concentrates treatment. A PLCC project considering the treatment of 200 ktpy of copper concentrates with arsenic from the northern district of Codelco; 2) EPAS DET project considering the treatment of 700 m3/d of weak acid solution with arsenic from the of El Teniente devision of the Codelco acid plant; 3) Borras project, considering the recovery of valuable metals (Cu, Ag, Ge, Pb) from the flue dust leaching plant; 4) Tailings project, considering the recovery of metal values from tailings. The purpose of this work is to present the trends and treatment processes for arsenic handling in the copper mining industry with a focus on the scorodite process. INTRODUCTION Between 2000 and 2015 the global copper concentrates production has grown from approximately eleven to fifteen million metric tons per year. Chile produced 26.5% of the total copper from concentrates and in the future copper production in Chile is expected to increase, mainly as a result of the production of concentrates (Figure 1)

Jan 1, 2019

By Arthur. H. Winckers, Stephan L. Chryssoulis

"The deportment of gold in residue samples of cyanide leach tests of David Bell ore from level 6A block 13 was established using a comprehensive quantitative mineralogical approach. In every test the feed was first pre-aerated for 4 hours, followed by 48h cyanidation. Test no. 2 was done without lead nitrate and yielded a residue assaying 3.03g Au/t. In test nos. 4 and 9 lead nitrate was added before pre-aeration at 0.03kg/t and 0.3kg/t respectively yielding residues of 1.04 and 0.81 g Au/t.The mineralogical approach employed to establish the deportment of gold involved superpanning, to preconcentrate the free gold and assaying of the tailing fraction to determine the gold associated with quartz. It was thus determined that without lead nitrate added 47.2% of the lost gold is in the form of residual free gold particles less than 20 µm in size. It is this form of gold which is under represented in the residues of leach tests with lead nitrate added.Having eliminated coarseness of gold particles as a factor for lower recovery, it was determined that the residual gold particles have extensively contaminated surfaces. Amongst the deleterious surface contaminants identified: S, As, Ag, Sb and Hg, the two most harmful are S and Hg because of their concentration on the surface and rate of accumulation.Mercury and Ag are minor constituents of native gold at David Bell (average composition Au: 78.9 wt%, Hg: 18.5 wt% and Ag: 2.6 wt%) and they become enriched on the surface of residual gold particles because of their slower rate of dissolution in cyanide. The other elements absorb onto the gold particles from solution.The beneficial effect of lead nitrate was documented by comparative surface analysis of gold from residue samples of 48 hour leach testing with and without lead nitrate added and from time dependent (0-2 hour) leach tests in the presence and absence of lead nitrate. Lead nitrate accelerates the dissolution of gold by performing the following functions: (i) catalytic effect on the cyanidation of gold by accepting electrons; (ii) reaction with surface sulphur to form PbS which is then removed by oxidation; (iii) catalytic reaction on amalgam and Ag facilitating the cyanidation of Hg and Ag thus slowing down their build up onto the dissolving gold particles and (iv) the precipitation of sulphide sulphur from solution thus minimizing its build up on the surface of dissolving gold particles which is believed to facilitate the access of cyanide ions."

Jan 1, 1996

By R. E. Dye

Introduction Research concerning all phases of hoisting practice, but more particularly the causes and prevention of hoisting rope deterioration and the improvement of safety dogs 158 for shaft conveyances, has been carried on intensively for the past three years in the Province of Ontario. Prior to the hoisting accident at the Paymaster mine on February 2nd, 1945, there had been no fatalities in the Province due to a hoisting rope failure. It was probably on this account that little original research on hoisting problems had been undertaken here and that the mining industry had been content to look to British, South African, and United States investigators for new developments in this field. Except for the Paymaster accident this might still be the case since, in any industry, it is apparently necessary for a serious accident to occur before any extensive programme of preventive research is launched. When this accident occurred, the Government of Ontario, with the close co-operation of the Paymaster officials and the mining industry as a whole, took immediate steps to determine the cause. A five-man, non-industry committee, selected from the Faculty of the University of Toronto with Dean C. R. Young as Chairman, was appointed by the Government, and a three-man Committee consisting of R. D. Parker, General Superintendent of the International Nickel Company of Canada, Limited, R. L. Healy, General Manager of Wright Hargreaves Mines, Limited, and R. E. Dye, General Manager of Dome Mines, Limited, with the latter acting as Chairman, was appointed by the Ontario Mining Association.

Jan 1, 1948

By J. Visman

"Cyclone separators of different design are being used in increasing numbers in the coal industry of today. One recent addition, the Compound Water Cyclone, is finding application in the North American and Australian coal fields for the beneficiation of coking coals and for the reduction of sulphur and ash in steam coals. In this paper, the combination of specific-gravity separation, thickening, classification and water recovery are discussed. All of these operations can now be accomplished by means of cyclones that are effectively combined in circuits of compact design. In the layout of such integrated plants, three main sections are distinguished, namely: a Main Section for cleaning the plus-28-mesh fractions; an Effluent-Beneficiation Section for treating the minus-28-mesh fractions; and a Water-Recovery Section, where the wash water is reconditioned, and the fine solids are removed in a semi-solid state as slugs or pellets. Depending on the nature of the coal and the specifications of the purchaser, water-cyclone circuits can be flexibly combined with HM Cyclones and froth flotation, as well as with ancillary equipment for dewatering and drying."

Jan 1, 1968

By Pierre Buteau

Peat/ands distribution in Canada is widely spread thoughout the country and corresponds to a wide spectrum of wetland habitats which overlay peat deposits. The development and the evolution ofpeat/ands and peat deposits are closely linked together, since the vegetal remains of the peat deposits originate from the peatland habitats, and the peatland habitats constitute a response to many factors, including the properties of the substrate, which are the peat deposits. Peat/ands are defined as waterlogged terrains where the production of plant materials usually exceeds the rate of decomposition. The underlying peat deposits consists of organic residues associated to peatland vegetation, more or less decomposed, built up and kept under anaerobic conditions. Peat/ands evolution and distribution are determined primarily by climatic factors, but also by the geomorphology and edaphic conditions. All of these create particular hydrodynamical environments which will vary according to different regional settings, and sequentially to an evolutive time frame.

Jan 1, 2001

By Qingxia Liu, Mingbo Zhang, Hongbo Zeng

The shortage of freshwater has been a major challenge for mineral flotation in arid areas. When using high salinity water, certain electrolytes are detrimental to flotation while others can improve the flotability of minerals. In this paper, the flotation behaviors and contact angles of pyrite in both Milli-Q water and high salinity water were investigated using different collectors at various pH levels. Results show that the thionocarbamate has a less affinity to pyrite in different solutions under mildly alkaline conditions as compared with potassium amyl xanthate (PAX) and N-isopropoxypropyl-N’-ethoxycarbonyl thiourea (iPOPECTU). At high pH levels, the slime coating on pyrite surfaces, which is caused by colloidal precipitates of magnesium and calcium ions in seawater, was confirmed by SEM, EDX and in-situ zeta potential measurement. The slime coating of colloidal precipitates on mineral surfaces led to low recovery of pyrite at high pH levels. The study of flotation behavior of pyrite in high salinity water improves our fundamental understanding of mineral flotation in seawater.

Jan 1, 2015

By James R. Hein

Manganese nodules form at the sediment surface of abyssal plains throughout the global ocean at water depths of about 4000-6500 m. The nodules form a continuum from purely hydrogenetic (all metals from seawater) to purely diagenetic (all metals from sediment pore waters), which will determine which metals of potential economic interest are enriched in the nodules. Another important factor in metal enrichment is whether diagenesis in the bottom sediment is oxic or suboxic. There are several nodule fields in the deep ocean that have received much attention with regards to economic potential, the most important being the Clarion-Clipperton zone (CCZ) in the NE Pacific, where the International Seabed Authority (ISA) has signed 12 contracts for exploration areas, each spanning 75,000 square kilometers. Those nodules are rich in nickel (mean 1.3 wt. %), copper (mean 1.1 %), and manganese (28%), with moderate amounts of cobalt (mean 0.2%), molybdenum (587 g/t), and lithium (129 g/t). A conservative estimate is that there exists 21,100 million dry tonnes of nodules in the CCZ, yielding more manganese, twice the nickel, three times the cobalt, and four times the yttrium than the entire land-based reserve base (economic plus marginally economic plus subeconomic reserves) for each metal. Total rare-earth elements (REEs) as oxides average 0.09% in CCZ nodules, a potential byproduct even at that grade because the heavy REE complement averages 26%, compared to less than 1% for the large land-based carbonatite REE deposits. The price for HREEs is much greater than for the light REEs. For comparison, the REEs in deep-ocean ferromanganese crusts are 3 to 5 times greater than nodules and the HREE complement averages 18%. Of the 12 CCZ contracts, 7 are with States (China, France, Germany, Japan, Korea, Russia, and a group of States (IOM); and 5 are with companies: G-Tec Sea Mineral Resources NV, Nauru Ocean Resources Inc. (NORI); Tonga Offshore Mining Ltd (TOML), UK Seabed Resources Ltd (Lockheed UK), and Marawa Research and Exploration Ltd. Three other nodule fields that have received attention are in the Peru Basin, which has nodules very rich in manganese (34%) and lithium (mean 311 g/t), the Penrhyn Basin (Cook Islands Exclusive Economic Zone), with nodules very rich in cobalt (mean 0.4%); and the Central Indian Ocean Basin (CIOB), where India has an exploration contract with the ISA. CIPB nodules have mean nickel, copper, and manganese contents of 1.1%, 1.0%, and 24% respectively.

May 1, 2013

By H. C. L. Reemeyer

"The mining industry faces increasing economic, environmental and social challenges, as easier deposits deplete and ores become more difficult to mine and process; head grades decline; projects migrate to increasingly remote and difficult geographies; and the industry faces more stringent environmental and social standards. While these factors increase costs and risks, they also present opportunities for a more integrated approach to mining, processing, materials handling and waste management. Two key areas of risk are in tailings and water management. As mining and processing tonnage rates continue to increase, the disturbance footprints, water and energy consumption and scale of tailings storage facilities also rise. These factors can be mitigated by more selective mining, ore sorting and pre-concentration, and more intensive tailings dewatering. Such alternatives must be considered in conjunction with the selection of mining method, metallurgical flowsheets, major equipment selection, and key process design criteria. For example, increasing the grind size of a concentrator reduces energy consumption and eases tailings dewatering, but may cause challenges with metal recovery. Emerging technologies will be reviewed, and economic and environmental trade-offs for eco-efficient alternatives will be presented for metal sulfide mines.INTRODUCTION The metals mining industry faces significant challenges that can affect its financial viability and social license to operate. There has been a consistent decline in ore grades and a relentless push towards larger operations to capture perceived economies of scale. With these larger operations, the environmental footprint of mines has increased. Water and energy consumption, and resulting GHG emissions have also risen. In recent years, two issues have raised special concerns for stakeholders and companies: • Water scarcity, particularly in drier regions of the world such as Northern Chile, SW USA, Southern Africa and Australia • Tailings risks, following the high-profile failures of the Fundao tailings dam in Minas Gerais, Brazil in 2015 and the Mount Polley tailings dam in BC, Canada in 2014"

Jan 1, 2017

By D. Campbell Mackenzie

THIS paper is submitted primarily to put on record the results of a number of experiments carried out at the Wingdam mine of Consolidated Gold Alluvials of B.C., Ltd., with the object of establishing a reliable method of concentration of 'wash' and a maximum recovery of gold from the concentrate. It will be generally admitted that, during the last two decades, a tremendous amount of research work has been carried out, both by private companies and Government departments, with a view to improving the technique of the recovery of gold .from quartz veins or lodes. So thorough have been these investigations that milling practice at a modern quartz gold mine is almost an exact science, carried out with meticulous accuracy. In placer mining, on the other hand, very little departure from old traditional methods can be noted, with the exception perhaps of the more modern gold dredges. This may be due to the fact that the concentration of placer gravels, up to a certain point, is comparatively easy. Only a simple equipment of sluice box and riffies seems necessary where the gold is coarse and the gravel free from clay. In the early days of placer mining, when claims were rich and fairly 5hallow, nobody worried very much about fine gold; and, if clay was present, an enlarged dump box was constructed in which the gravel was subjected to a rather desultory puddling. That large quantities of gold are lost in normal placer practice is generally admitted. Some 26 years ago, I had inspectorial charge of many bucket dredges on the Ovens river, in Australia. Occasionally it was necessary for a dredge to work through its own tailing to reach a new section, and almost without exception enough gold was recovered from these tailings to defray the total cost of moving the dredge. Since those days, the technique of gold recovery in dredging has been considerably improved and it is still receiving close attention. Outside of dredge mining, most placer operations, deep or otherwise, are as they were-notorious gold losers, paying little attention to the recovery of fine gold and taking an absurd amount of time over each clean-up. In the Cariboo district of British Columbia, the alluvial gold is usual y associated with varying quantities of black sand (magnetic) and grey sand (non-magnetic); and it can be taken as axiomatic that, if you save all the black sand and grey sand, you save practically all the gold. It is on this hypothesis that we have carried out our research work and brought our recovery system up to its present highly satisfactory standard.

Jan 1, 1937

By R. N. Chakravorty

Early detection of spontaneous combustion is of utmost importance in underground coal mining to prevent major disruptions of production and to ensure a safer working environment. This paper presents the work done in developing a suitable system for the early detection of heating in a hydraulic coal mine. Laboratory studies on the products of oxidation for Balmer 10 seam coal showed that a significant amount of carbon monoxide is produced during the early stages of heating and that detection methods based on the analysis of other gases, such as hydrogen, ethane or ethylene, are not a better alternative for this coal. The four-point carbon monoxide monitoring system recently installed at the hydraulic mine is discussed in this paper. It is believed that by studying the trend of carbon monoxide concentration in the mine air, it will be possible to detect heating at an early stage. Field tests carried out so far have indicated that infra-red technology will prove to be a powerful tool in the hydraulic mine, particularly for locating hidden oxidation or fire in cracks, fissures, underground workings and coal outcrop areas before it spreads extensively. The project is jointly sponsored by EMR, CANMET, Mining Research Laboratories and Kaiser Resources Ltd.

Jan 1, 1978