Search Documents

By Y. J. Yu, C. D. Zhang, Y. S. Zhao, W. G. Liang, Y. D. Geng, J. L. Bi

"In this study, the coefficient of thermal expansion (CTE) and thermal conductivity (TC) of shale in two perpendicular directions, vertical and parallel to the bedding of the rock, are firstly measured by experiment. The experimental results show that the CTE of the shale in the vertical direction is 1.69 times as much as that in the parallel direction, while the TC in the parallel direction is 1.83 times larger than that of the vertical direction. Based on the no initial strain assumptions, numerical simulations for the thermal cracking in shale are carried out with the obtained coefficients. Using finite element method and thermal-mechanical coupling theory, two fracture mechanical parameters, KI and J-integral of the shale are also analyzed for the shale thermal fracturing. The simulation results show that both KI and J-integral reach the maximum when the fracturing angle equals to 0° in the shale, namely parallel to the bedding direciton. It is also found that the two fracture parameters decrease with the fracturing angle increasing. Additionally, the thermal fracturing effect of the shale is evaluated under a given scenario. The study is significant for shale oil or gas recovery by in situ pyrolyzing method.INTRODUCTIONOil shale is regarded as a kind of unconventional resource that can contribute to production of shale oil and hydrocarbon gases (Rahm & Dianne, 2011). As is known that there is a large deposit of oil shale in China, and present technology for exploiting oil shale still concentrates on open-pit mining, obtaining shale oil by retorting shale on the ground (Li, Tang, Xue, Zheng, & Du, 2014; Qian, Yin, 2008). However, this technology has a bad effect on the environment and leads to severe resource waste for utilizing oil shale. Exploiting oil shale by in-situ method for ‘green mining’ is widely necessary in China (Kang, Wang, Cao, Liang, Chang, & Liu, 2013; Waters, Dean, Downie, Kerrihard, Austbo, & McPherson, 2009; Zoback, Kohli, Das, & McClure, 2012). One of effective method to exploit shale oil is heating oil shale in-situ underground. For instance, the in-situ conversion process (ICP technique) from Shell Company etc. used a direct heating method, and convectional heating oil shale underground by injecting superheated steam from Mining Technology Institute, Taiyuan University of Technology and constructing horizontal fracture in vertical wellbore from Chevron Company use indirect heating method (Chaudhary, Ehlig, & Wattenbarger, 2011; Hazra, Lee, Economides, & Moridis, 2013; Zhao et al., 2010). The convectional heating method contains complicated procedures with phase transition in double-media of fracture-matrix of oil shale subjected to multi-physical fields coupling including stress, fluid and temperature (Zhao et al., 2010). The characteristics of thermodynamics, solid mechanics and seepage of oil shale have been investigated separately (Hopkins, Rosen, & Hill,1998; Kang, Zhao, & Yang, 2008; Yang, Zhao, Kang, 2010; Zhao, Yang, Feng, Liang, & Kang, 2008; Zhao, Cao, Zhao, Lin, & Wang, 2008). However, it is quite difficult to solve constrained problem of each physical parameter in multi-physical fields coupling for oil shale pyrolysis."

Jan 1, 2015

By Douglas Macaulay

"The Work contains the personal views and opinions of the Author and in no manner should it be construed as reflecting the official position of Export Development Canada. The Author makes no representation or warranty with respect to the accuracy or completeness of the contents of the Work and specifically disclaims any implied warranties, merchantability or fitness of use for a particular purpose". Export Development Canada ?Canada?s official export credit agency, established 1944 ?Mandate to support export and foreign investment ?Financially self-sustaining, AAA rated borrower ?Services include: Financing (FIN), Political Risk Insurance (PRI), Contract Insurance & Bonding (CIB), Accounts Receivable Insurance (ARI) ?A trusted partner in troubled times

May 1, 2010

By G. J. Simandl

"Since the 1980s, China has become the predominant producer of REEs. Recently, it introduced REE export quotas and this started a world-scale REE exploration rush. REE resources are concentrated in carbonatite-related deposits, peralkaline igneous rocks, pegmatites, REE ± P veins, ion adsorption clays, placers, and some deep ocean sediments. REEs could also be derived as a by-product of phosphate fertilizer, U processing, Ti-Zr-bearing placers, and exploitation of Olympic Dam-type sub-type of IOCG deposits. The ideal REE development target would be located in a politically stable jurisdiction such as Canada. REE grade and tonnage, mineralogy, and permissive metallurgy are some of the key technical factors that could be used to screen projects. INTRODUCTIONAccording to the International Union of Pure and Applied Chemistry (IUPAC), the term “rare earth elements” (REEs) encompasses yttrium (Y), scandium (Sc), and the lanthanide series: lanthanum (La), cerium (Ce), praseodymium (Pr), neodymium (Nd), promethium (Pm), samarium (Sm), europium (Eu), gadolinium (Gd), terbium (Tb), dysprosium (Dy), holmium (Ho), erbium (Er), thulium (Tm), ytterbium (Yb), and lutetium (Lu). This definition is used throughout this paper.REEs are subdivided into light (LREE) and heavy (HREE) categories. LREEs include, Sc, La, Ce, Pr, Nd, Sm, Eu, and Gd and HREE include Tb, Dy, Ho, Er, Tm, Yb, Lu, and Y. Promethium (Pm) does not occur in nature. Concentrations of individual LREEs in the upper crust of the Earth are comparable to those of base metals. Even the least abundant REE (Lu) is about 200 times more abundant than gold.The production of REEs, reported in the form of oxides (REOs), for 2011 is estimated at 140 000 t (Figure 1a). Although high technology industries can substitute several REEs with other materials, these substitutes are typically more expensive or less effective than the REEs they replace. A number of countries, including the United States, consider several REEs essential for national security, their economy, and a general reduction in green house gas emissions. The forecasted demand for individual LREOs is much higher than that of HREOs (Figure 2). Dy, Eu, Tb, Nd, and Y are essential for the US economy and subject to predicted supply disruptions (U.S. Department of Energy, 2010)."

Jan 1, 2012

By P. Lafleur

All indications point to a growing market for thermal coal in Japan as part of the country's current energy policy formulation process. The Ministry of International Trade and Industry forecasts imports of 16 million tons a year in 1985 and 40 million tons in 1990-a twenty-fold and forty-fold increase over the present level. This potential reflects Japan's over-all serious and increasing concern for security of energy supplies and its resultant need to seek alternative sources. Nuclear power will be the main alternative source, but, because it is expected that its development will be slow, imported thermal coal will assume greater importance. Canada, with large resources of all types of coal, could fill a portion of this market. Thermal coal could come from specific thermal coal developments or from metallurgical coal mines, which usually produce a certain amount of coal not amenable to coking, but suitable for power purposes. However, penetration of this Japanese market by Canadian thermal coal will depend on the resolution of a number of problems. On the demand side, siting, environmental aspects, the need for a coal unloading and trans-shipment centre, and the added cost of installing coal-fired stations could be major constraints. Although Canada has ample high-quality resources, any new development tied to the Japanese market will require improvement in prices to cover the high costs associated with transportation, the construction of new mines and the provision of new infrastructure.

Jan 1, 1979

By R. K. Carnochan

MANY improvements have been made in recent years in the milling of industrial minerals and it is the purpose of this paper to review some of the more important innovations that are now being used in the preparation of these products. Some of the observations which will be made have been prompted by what was seen on a recent trip to industrial mineral milling plants in the north and central sections of the eastern United States. The flotation plants visited were those of the Valley Forge Cement Company at West Conshohocken, Pa., the International Agricultural Corporation at Mount Pleasant, Tenn., and the Aluminum Ore Company at Rosiclare, Ill. Besides these, sand plants in Pennsylvania, West Virginia, and Ohio, coal-cleaning plants in Pennsylvania, pyrophyllite, mica, feldspar, clay, and kyanite plants in North Carolina, and a zinc mill and the Tennessee Valley Authority ceramic laboratory in Tennessee were visited. The milling of industrial minerals can be considered under three broad headings, namely, crushing, grinding, and purification. Usually there is both a separation and grinding problem in treating an industrial mineral, but the problems are distinct, although sometimes a separation is made while grinding, as in the case of a Raymond throw-out mill, which grinds and at the same time throws out most of any hard material present in its feed.

Jan 1, 1939

By Juliana Parreira

The past decade shows record increases in global demand for minerals and metals with an accompanying significant decline in skilled personnel. Mining companies today are examining new technologies to maximize production, reduce costs, and create safer work conditions to deal with this shortfall. Automation of an open-pit mine haulage system is receiving attention as a beneficial option since it provides more consistent and efficient operation of mining equipment, it removes workers from potential danger, it reduces fuel consumption significantly reducing greenhouse gas (GHG) emissions, and it can help optimize vehicle repairs and equipment replacement because of more-predictable and better-controlled maintenance. This paper describes a simulation model under development using the EXTENDSIM software package to examine scale-up issues and constraints of autonomous vehicles in comparison to a manual system. The software can predict and manage Key Performance Indicators (KPIs), such as productivity, safety, cost, equipment failures, fuel consumption, and tire wear under different road and load conditions. By breaking-down the various systems of an autonomous haulage truck and simulating the overall haulage system using a Monte Carlo approach, the model becomes a flexible and powerful tool to use within a mining organization. Direct comparison to a manuallyrun system can be done to show the cost and operational benefits of automation. Project managers can use this tool to guide decision-making about possible application of autonomous haulage trucks at a specific mine site.

May 1, 2010

By F W. Irwin

In recent years, a number of significant developments have occurred in the steel industry which are no-table and of general interest. This paper is confined to the steel-melting phase of the business. The development of high production rates on Stelco's Basic Open Hearth furnaces is chronologically summarized. Al-though various aspects of this subject have been presented previously, this paper summarizes the developments in high fuel rates, the usage of basic refractories, low and high oxygen rates and hearth maintenance. Background T HE interest which has been shown in steelmaking techniques in the past few years has been due, primarily, to the extremely high production rates obtained. Upon further study of the facilities and techniques employed to generate this steel at record rates, tonnage oxygen appears as the common factor. It can be stated that tonnage oxy-gen has revolutionized steelmaking techniques to a degree never before encountered. It was only about ten years ago that the use of large amounts of pure oxygen in a steelmaking

Jan 1, 1965

By C. S. Simons, D. A. Dahlstrom

"Growing interest in the developing technique of improving the dewatering of filter cakes by the direct application of steam has been apparent during the past year. A number of applications to iron and base-metal concentrates are under study, and intensive work continues on applications to coal cleaning.This paper presents and discusses the data presently available. The effects of material characteristics and operating variables on final cake moisture are examined. Although it is not yet possible to answer all questions regarding the applicability of the technique to specific problems from general data correlations, it is found that the use of these in con-junction with empirical data derived from properly conducted laboratory tests does yield reliable conclusions.Emphasis is placed on the basic economics of the process, and on de-sign criteria for ""steam drying"" filter stations, as applied particularly to metallurgical concentrates. Examples of the use of laboratory tests to solve application problems are given."

Jan 1, 1966

By C. G. McLachlan

INTRODUCTION The work described in the following paper was under-taken with a view to determining, if possible, the relative importance of some of the phenomena on which flotation seems to depend, in the hope that, if this information could be obtained, it would be of value in dealing with the problem as a whole. At the outset, brief reference will be made to three papers which had a considerable bearing on the course followed in the present investigation. In 1919, Langmuir, in a paper on 'The Mechanism of the Surface Phenomena of Flotation', showed that mono-molecular films of very great stability could be produced on solid surfaces with oleic acid, but that pure paraffin oil, though spreading readily on a dean dry surface, was easily displaced by water.

Jan 1, 1926

By N. Bahrani

Photogrammetry surveys were used to document a footwall slab failure that occurred at a surface coal mine located on the eastern slope of the Rocky Mountains. Photographs taken before and after the failure provided the pre- and post-failure geometry of the slope and the failed slab. A 2D finite element model was constructed using slope profiles. The model contained joint elements that represented the bedding surface upon which the slab slid and the model was used to analyze the footwall slope. The in situ stresses, rock properties and the bedding surface shear strength and stiffness properties are discussed. The process of mining out a valley and exposing a highwall was modelled. As expected, elastic valley rebound occurred in the model, but shear stress and shear displacement reversals along the slip surface were also observed. The modelling results provided new insight into shear strength degradation that occurs when the pit floor approaches and then passes a specific point in the highwall.

Jan 1, 2009

By N. R. Thote, J. L. Porathur, C. P. Verma

Highwall mining is a highly mechanized coal mining method associated with several advantages, such as a very high production rate (approximately 3,000 t/d) and low production costs. There is no requirement for underground support, ventilation, or blasting. Production leads to added recovery, which is otherwise lost in the ultimate pit. The use of highwall mining can bridge the gap that exists between supply and demand in the energy sector. This paper presents a brief review of highwall mining technology, including current status, analysis tools, and design techniques. In addition, it identifies important parameters from the analysis of failure case studies.

Jan 1, 2014

By C. R. Julian

MECHANIZATION During the last fifteen years, numerous attempts have been made to mechanize the operations of loading ore and placing till. It is to be regretted that, to date, little progress has been made in this direction. The comparative efficiency of manual labour in Spain is the factor largely responsible for the failure to cheapen costs by mechanization. The necessity for careful classification of the ore and the need for keeping all openings small also makes the problem one of difficulty. It may be of interest to describe the various attempts at mechanization that have so far been made. CONVEYORS: (1) When stoping by layout III in San Dionisio, a trial was made of transporting the filling by jigging conveyors. This method proved un-economical, as the wall building and spreading of the till could not keep pace with the delivery, with the result that the machinery was idle a great part of the shift. (2) The transport of ore from the working places to the ore-passes by jigging conveyors and belts was also tried. Although more successful than in the case of the fill, the method could not compete with that of hand tramming, principally due to the high cost of (a) maintenance caused by the abrasiveness of pyrites, and (b) labour constantly employed on re-aligning the conveyors owing to the constant settlement of the floor. In a few cases, where a sill floor was being blocked out in virgin ground, the method showed a saving. SCRAPERS: Frequent attempts at loading by scrapers have been made, but again the only success obtained has been in the blocking-out of sill floors. The principal obstacle to the successful application of scraping, other than on the sill floor, has been that the openings, which have to be small, call for a light scraper outfit, whereas, in practice, a heavy scraper and at least a 25 h.p. winch are necessary for handling satisfactorily the ore, which is heavy and which breaks somewhat blockily.

Jan 1, 1940

By C. A. Jeffrey, K. Pearson

Abstract - The Croft diorite in central England belongs to a suite of Caledonian igneous rocks collectively known as the South Leicestershire diorite complex. Although the intrusions occupy separate outcrops, they are linked at depth to form a single pluton, buried beneath a cover of Triassic sediments (Le Bas, 1972; 1982, Allsop and Arthur, 1983). Both the Caledonian diorites and the overlying sub-Triassic unconformity have been affected by a complex history of alteration and mineralization which can be subdivided into four stages: (1) deuteric effects, caused by the release of volatiles during magmatic cooling; (2) albitization through sodic enrichment; (3) formation of lowtemperature laumontite, analcime and calcite veins with associated wall-rock alteration to prehnite and pumpellyite; and (4) sub-Triassic unconformity-hosted base metal, manganese and palygorskite mineralization. Zeolite mineralization occured some 200 Ma later than the intrusion itself, during post-Triassic times, as indicated by the presence of a single vein of laumontite and microcrystalline calcite which cross-cuts the sub-Triassic unconformity surface and enters the overlying Triassic sediments. Evidence from fluid inclusion work indicates that two fluids were involved in the deposition of the zeolite veins. One fluid was initially of relatively high temperature (~100°C to 320°C) and low salinity (~0.2 to 5.9 wt% NaCl equiv.), and was probably meteoric in origin, whereas the other was of relatively low temperature (~41°C to 165°C) and high salinity (~0.4 to 16.72 wt% NaCl equiv.), and is interpreted to represent a basinal brine. During Triassic rifting, thinning and fracturing of the crust, with the possible rise of associated magmas (Halliday and Mitchell, 1984), could have increased permeability and heat flow, initiating the circulation of hydrothermal fluids. Triassic unconformity-hosted base-metal mineralization in Central England is similar to other Triassic-Jurassic mineralization in Europe (Mitchell and Halliday, 1976).

Jan 1, 1997

By C. A. Jeffrey, K. Pearson

The Croft diorite in central England belongs to a suite of Caledonian igneous rocks collectively known as the South Leicestershire diorite complex. Although the intrusions occupy separate outcrops, they are linked at depth to form a single pluton, buried beneath a cover of Triassic sediments (Le Bas, 1972; 1982, Allsop and Arthur, 1983). Both the Caledonian diorites and the over-lying sub-Triassic unconformity have been affected by a complex history of alteration and mineralization which can be subdivided into four stages: (1) deuteric effects, caused by the release ofvolatiles during magmatic cooling; (2) albitization through sodic enrichment; (3) formation of low-temperature laumontite, analcime and calcite veins with associated wall-rock alteration to prehniteand pumpellyite; and (4) sub-Triassic unconformity-hosted base metal, manganese and palygorskite mineralization. Zeolite mineralization occured some 200 Ma later than the intrusion itself, duringpost-Triassic times, as indicated by the presence of a single vein of laumontite and microcrystallinecalcite which cross-cuts the sub-Triassic unconformity surface and enters the overlying Triassic sediments. Evidence from ?uid inclusion work indicates that two ?uids were involved in the deposition of the zeolite veins. One ?uid was initially of relatively high temperature (~100°C to 320°C) and lowsalinity (~0.2 to 5.9 wt% NaCl equiv.), and was probably meteoric in origin, whereas the other wasof relatively low temperature (~41°C to 165°C) and high salinity (~0.4 to 16.72 wt% NaCl equiv.),and is interpreted to represent a basinal brine. During Triassic rifting, thinning and fracturing of the crust, with the possible rise of associated magmas (Halliday and Mitchell, 1984), could have increased permeability and heat ?ow, initiating the circulation of hydrothermal ?uids. Triassic unconformity-hosted base-metal mineralization in Central England is similar to other Triassic-Juras-sic mineralization in Europe (Mitchell and Halliday, 1976).

Jan 1, 1997

By W. E. Cockfield

THE object of this paper is to review recent geological work in the Cariboo district and to present notes on the recent development of mineral properties. The Geological Survey has done considerable work in the Cariboo district, extending over a period of years. In 1885 and 1886, Bowman (1) mapped the geology of a large area. In 1922 and 1923, Johnston and Uglow (2) mapped Barkerville area in some detail and prepared a report on the placer and lode gold deposits. In 1931 and 1932, Cockfield and Walker (3) mapped the Quesnel Forks area. In 1933, Hanson reported on Willow River area ( 4), and in 1934 made a detailed examination of part of the Barkerville area (5). In 1935, Lang commenced work on the Keithley area, lying to the southeast of the Barkerville area, and in 1936 published a preliminary re-port (6). The work on Keithley area was continued in 1936 by both authors of the present paper. As the results of the earlier work have been published, this paper will be concerned largely with Keithley area, that is, the part of the region lyinp between longitudes 121° 00' and 121° 30', and latitudes 52° 45' and 53° 00 . This area lies astride Cariboo (Swamp) river and extends north some 17 miles from Keithley, which is situated near the southern border of the map-area (see sketch-map). Points in the western part of the map-area are fairly accessible. A road extends from Barkerville to upper Cunningham creek, and from this a trail crosses Snowshoe plateau to Keithley. A second trail from this road leads to the lower falls on Cariboo river. From this road, a branch road leads to upper Antler creek, with a trail leading from this branch road to Keithley. Part of this western half of the area is made up of the Snowshoe plateau, which constitutes a gently rolling surface, at or above timber line, where trails are largely unnecessary.

Jan 1, 1937

By F. Awotwe-Appiah, P. Koshy, A. Y. Fosu, J. Dankwah, J. R. Dankwah

Ghana currently exports its bauxite raw without any value addition. Gradual depletion of high grade bauxite (with high alumina content) and the emergence of low grade bauxite (with high iron oxide content) calls for novel and inexpensive ways to recover alumina from these low grade ores. Bauxite users have indicated their willingness to pay 10% to 50% higher for a corresponding reduction in impurities by a similar amount. This project therefore investigates the carbothermal upgrading of the Ghana Awaso bauxite using waste polypropylene as reductant in a locally designed gas-fired furnace. Composite pellets of low grade bauxite sample (assaying 45% Al2O3) containing pulverised waste polypropylene were formed, oven dried, placed in fireclay crucible and fired for 30 minutes. The magnetic fraction after reduction was separated by a Low Intensity Magnet and weighed. It was observed that up to 97% of the iron oxides (occurring as hematite and goethite) could be separated into the magnetic fraction as magnetite leaving a nonmagnetic fraction with over 98% Al2O3 as opposed to the 45% Al2O3 in the as-received bauxite sample. This research direction provides yet another simple but effective way for simultaneously upgrading low grade bauxite and recycling waste polypropylene, whilst at the same time decreasing the amount of waste material generated as red mud after the Bayer process.

Jan 1, 2015

By T. A. Utigard, S. Pedler

Ilmenite from the Everett deposit in Quebec was characterized both chemically and mineralogically. The sample investigated contained the following main components: 40% Fe2O3, 21% TiO2 and 21% SiO2. The ilmenite grains contained about 20 to 25% hematite intergrown blades, with widths ranging from 2 to 30 \u03bcm. Crushing the sample to less than 0.85 mm led to significant liberation of the ilmenite from the gangue minerals. Gravity separation followed by magnetic separation of this size fraction led to a TiO2 concentrate grading of about 30% TiO2, with a recovery of 94%.

Jan 1, 2010

By Biplop Das, E. Herrera, A. Burrows, P. J. Mackey, G. R. F. Alvear Flores

Since the first commercial plant was built at Mount Isa, another twenty ISASMELT™ furnaces have come into commercial operation, and construction of new plants continues. The primary copper ISASMELT™ top submerged lance (TSL) technology continues to attract interest from potential users who seek to smelt productively. In addition to the known benefits of productivity and flexibility, ISASMELT™ operators have also achieved improvements to energy efficiency when switching from their previous technologies. The recent production statistics for operation at Tuticorin, India show that ISASMELT™ has taken the first steps into territory beyond 400,000 t/y (copper cathode basis) and this will likely be the scale chosen by future new copper smelters operating purely on a toll smelting basis. Highly energy-efficient technologies will be expected at these smelters

Jan 1, 2015

By E. R. Weltevreden, C. Klauber, C. Vernon

"In this paper a review of the current status in recycling technologies for cathode ray tubes is given for both the glass and phosphors. Particular emphasis is placed on the opportunities for the recovery of the rare earth elements (REE) from the phosphor coatings. This is placed in the market context of alternative virgin sources and some of the advantages and disadvantages for REE waste recovery. Future opportunities are explored and also some experimental detail on a low cost leach system is presented. INTRODUCTIONThe disposal of cathode ray tube (CRT) based colour televisions has accelerated world-wide with the development of high definition flat screen panels. The total number of colour CRT televisions that have been sold in the United States in the mid-20th century is estimated to have been over 2 billion (U.S. Environmental Protection Agency, 2007), with high current rates of disposal. It is estimated that of the 20 million televisions annually discarded, 78% are send to landfill (Nnorom, Osibanjo & Ogwuegbu, 2011). However, this easily accessible item of electronics cannot only be turned into a valuable resource using the right recovery procedures, it can also prevent the substantial environmental contamination arising from improper disposal. In this review we focus on previous and current work performed on the recycling of CRT based televisions. Due to the increasing demand for rare earth metals, the main focus will be on the possibilities and challenges of recycling the fluorescent phosphor powders on the CRT’s panel glass.CATHODE RAY TUBE’S GLASS RECYCLINGConventional cathode ray tubes consist of three main parts, the panel, the funnel and the neck (Figure 1). To produce the different colours on the screen, the inside of the panel is coated with a matrix of hundreds of thousands of small phosphor dots. Each dot is one of three types of coloured phosphors, emitting either red, green or blue light. These emit light when excited by a beam of electrons generated by electron guns located in the neck of the CRT. These beams pass through holes in the shadow mask and excite the phosphor coating on the inside of the panel, to give light of variable RGB composition, see Figure 1."

Jan 1, 2012

By R. Bainbridge

THE cinnabar deposits of the Consolidated Mining and Smelting Company's Pinchi Lake property, situated near Fort St. James, B.C., were discovered and reported on by a Dominion Government geological party in 1937. Claims were staked by a group of local prospectors and, later, the Consolidated Mining and Smelting Company of Canada, Limited, took an option on the property. By the fall of 1939, exploration work had indicated ore of commercial quantity and grade, and laboratory tests had shown that standard methods of reduction, namely, roasting of the ore, followed by condensation of the mercury vapour produced, would result in satisfactory recovery. In June, 1940, construction of a 50-ton unit arranged for wood firing was completed and operation commenced. The installation consisted of a 46 in. by 60 ft. rotary kiln (see Figure 1) followed by a 14-in. Sirocco cyclone, a cast-iron condenser unit, and a 1,700 c.f.m. fan, exhausting to a stack. Other equipment included a 9 in. by 18 in. Denver jaw crusher with the necessary bins and feeders. As the need for mercury was urgent, because of war requirements, construction of a duplicate unit was begun almost immediately. This first extension started operation in January, 1941, and the plant was then capable of treating about 150 tons of ore daily.

Jan 1, 1945